Switch to the new generic functions. Plain convert, no functionality
added yet.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The probe function is a little bit messy, something here, something
there. Rework it so that there is some order: first init the private
structure, then the adapter, then do HW init. This also allows us to
remove the device argument of the clock calculation function, because it
now can be deduced from the private structure. Also, shorten some lines
where possible. This is a preparation for further refactoring.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Inspired from the i2c-rk3x driver (thanks guys!) but refactored and
extended. See built-in docs for further information.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On an hardware shared I2C bus (certain Intel Baytrail SoC platforms) the
runtime PM disable depth keeps increasing over repeated modprobe/rmmod
cycle because pm_runtime_disable() is called without checking should it
be disabled already because of bus sharing.
This hasn't made any other harm than dev->power.disable_depth keeps
increasing but keep it sync by calling pm_runtime_disable() only when
runtime PM is not disabled.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because of some hardware limitation, AMD I2C controller can't
trigger pending interrupt if interrupt status has been changed
after clearing interrupt status bits. Then, I2C will lost
interrupt and IO timeout.
According to hardware design, this patch implements a workaround
to disable i2c controller interrupt and re-enable i2c interrupt
before exiting ISR.
To reduce the performance impacts on other vendors, use unlikely
function to check flag in ISR.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.
In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.
The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The read and write opcodes are global for all units on SoC and even across
Intel SoCs. Remove duplication of corresponding constants. At the same time
convert all current users.
No functional change.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boon Leong Ong <boon.leong.ong@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With ACPI _DSD (introduced in ACPI v5.1) it is now possible to pass device
configuration information from ACPI in addition to DT. In order to support
this, convert the driver to use the unified device property accessors
instead of DT specific.
Change to ordering a bit so that we first try platform data and if that's
not available look from device properties. ACPI *CNT methods are then used
as last resort to override everything else.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Allow the eg20t I2C driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set the I2C adapter devices of_node to that of the PCI device, such that
I2C clients may be instantiated via device tree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The hold field allows to configure the data hold time which can be set
with the help of the generic binding 'i2c-sda-hold-time-ns'. This
feature has been introduced with SAMA5D4 SoC family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For platform with auto restart support, between every transfer,
i2c controller will trigger an interrupt and SW need to handle
it to start new transfer. When doing write-then-read transfer,
instead of restart mechanism, using WRRD mode to have controller
send both transfer in one request to reduce latency.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The suspended flag is a flag holding the device's PM status.
The runtime framework does that for us.
Use pm_runtime_suspended call instead.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the clocks are enabled at probe and disabled at remove.
Which keeps the clocks enabled even if no transaction is going on.
This patch enables the clocks at the start of transfer and disables
after it.
Also adapts to runtime pm.
converts dev pm to const to silence a checkpatch warning.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As reported in the links given below. the BCM2835 has a hardware bug in
its i2c module which prevents a correct clock stretching. This patch
adds the I2C_AQ_NO_CLK_STRETCH quirk flag to i2c-bcm2835.
Signed-off-by: Nicola Corna <nicola@corna.info>
[wsa: put the links into the code as comments]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add I2C_AQ_NO_CLK_STRETCH to drivers/i2c/algos/i2c-algo-bit.c when getscl
is not available.
Signed-off-by: Nicola Corna <nicola@corna.info>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All protected sections are only called from sleep-able context, so there is
no need to use a spinlock.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The simple_strtoul function is marked as obsolete.
This patch replace it by kstrtou8.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C controller used in Keystone SoC has an undocumented peculiarity which
results in SDA-SCL margins being dependent on module clock. Driving high
capacity bus near its limits can result in STOP condition sometimes being
understood as REPEATED-START by slaves (or NACK instead of ACK, etc...).
Driving the module with higher clocks increases the margin between SDA and SCL
transitions, making the operations with higher bus rates more robust. Therefore,
target the module clock to 12MHz instead of 7MHz, still staying within
the specification limits.
Before the change STOP timing looked like this on 400kHz:
SDA ----------+ +----
\ /
\ /
+----+
(1)
SCL --+ +------------
\ /
\ /
+----+
(2)
While only point (1) signals STOP, point (2) could be incorrectly recognized as
repeated-START (almost no margin between SDA and SCL transitions).
After the change there is at least 600ns margin measured between SCL fall and
SDA fall during STOP generation:
SDA ------+ +----
\ /
\ /
+----+
SCL --+ +--------
\ /
\ /
+----+
->| |<- 600ns
->| |<- tSUSTO
So called tSUSTO (setup time for STOP condition) is still slightly higher than
600ns, so no problem here.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to the datasheets the n factor for dividing the tclk is
2 to the power n on Allwinner SoCs, not 2 to the power n + 1 as it is
on other mv64xxx implementations.
I've contacted Allwinner about this and they have confirmed that the
datasheet is correct.
This commit fixes the clk-divider calculations for Allwinner SoCs
accordingly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch adds support for port names for the SB800 chipset.
Since the chipset supports a multiplexed main SMBus controller, adding
the channel name to the adapter name is necessary to differentiate the
ports better (for example in sensors output).
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. The multiplexed ports share the same SMBus address and
register set. The port is selected by bits 2:1 of the smb_en register
(0x2C).
Only one port can be active at any point in time therefore a mutex is
needed in order to synchronize access.
Additionally, the commit avoids requesting and releasing the SMBus base
address index region on every multiplexed transfer by moving the
request_region call into piix4_probe.
Tested on HP ProLiant MicroServer G7 N54L (where this patch adds
support to access sensor data from the w83795adg).
Cc: Thomas Brandon <tbrandonau@gmail.com>
Cc: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. Therefore the static variable piix4_main_adapter is
converted into a piix4_main_adapters array that can hold one
i2c_adapter for each multiplexed port.
The auxiliary adapter remains unchanged since it represents the second
(not multiplexed) SMBus controller on the SB800 chipset.
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated, e.g. when receiving NACK in address
phase. To keep the race window as small as possible, we clear it right
at the beginning of the interrupt. We don't need any checks since we
always want to stop START and STOP generation on the next occasion after
we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to the HW design, master IRQs are timing critical, so give them
precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After making sure to reinit the HW and clear interrupts in the timeout
case, we know that interrupts are always disabled in the sections
protected by the spinlock. Thus, we can simply remove it which is a
preparation for further refactoring. While here, rename the timeout
variable to time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When calculating the bus speed, the clock should be on, of course. Most
bootloaders left them on, so this went unnoticed so far.
Move the ioremapping out of this clock-enabled-block and prepare for
adding hw initialization there, too.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes obvious copy-past error in wake up irq parsing
code which leads to the fact that dev_pm_set_wake_irq() will
be called with wrong IRQ number when "wakeup" IRQ is not
defined in DT.
Fixes: 3fffd1283927 ("i2c: allow specifying separate wakeup interrupt in device tree")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: <stable@vger.kernel.org> # v4.3
Pull i2c updates from Wolfram Sang:
- New drivers: UniPhier (with and without FIFO)
- some drivers got some bigger rework: ismt, designware, img-scb (rcar
had to be reverted because issues were showing up just lately)
- ACPI: reworked the device scanning and added support for muxes
... and quite a lot of driver bugfixes and cleanups this time. All
files touched outside of the i2c realm have proper acks.
* 'i2c/for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits)
i2c: rcar: Revert the latest refactoring series
i2c: pnx: remove superfluous assignment
MAINTAINERS: i2c: drop i2c-pnx maintainer
MAINTAINERS: i2c: mark also subdirectories as maintained
i2c: cadence: enable driver for ARM64
i2c: i801: Document Intel DNV and Broxton
i2c: at91: manage unexpected RXRDY flag when starting a transfer
i2c: pnx: Use setup_timer instead of open coding it
i2c: add ACPI support for I2C mux ports
acpi: add acpi_preset_companion() stub
i2c: pxa: Add support for pxa910/988 & new configuration features
i2c: au1550: Convert to devm_kzalloc and devm_ioremap_resource
i2c-dev: Fix I2C_SLAVE ioctl comment
i2c-dev: Fix typo in ioctl name reference
i2c: sirf: tune the divider to make i2c bus freq more accurate
i2c: imx: Use -ENXIO as error in the NACK case
i2c: i801: Add support for Intel Broxton
i2c: i801: Add support for Intel DNV
i2c: mediatek: add i2c resume support
i2c: imx: implement bus recovery
...
The asm-generic changes for 4.4 are mostly a series from Christoph Hellwig
to clean up various abuses of headers in there. The patch to rename the
io-64-nonatomic-*.h headers caused some conflicts with new users, so I
added a workaround that we can remove in the next merge window.
The only other patch is a warning fix from Marek Vasut
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dQKG
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"The asm-generic changes for 4.4 are mostly a series from Christoph
Hellwig to clean up various abuses of headers in there. The patch to
rename the io-64-nonatomic-*.h headers caused some conflicts with new
users, so I added a workaround that we can remove in the next merge
window.
The only other patch is a warning fix from Marek Vasut"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: temporarily add back asm-generic/io-64-nonatomic*.h
asm-generic: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
gpio-mxc: stop including <asm-generic/bug>
n_tracesink: stop including <asm-generic/bug>
n_tracerouter: stop including <asm-generic/bug>
mlx5: stop including <asm-generic/kmap_types.h>
hifn_795x: stop including <asm-generic/kmap_types.h>
drbd: stop including <asm-generic/kmap_types.h>
move count_zeroes.h out of asm-generic
move io-64-nonatomic*.h out of asm-generic
This whole series caused sometimes timeouts and even OOPSes on some
r8a7791 Koelsch boards. We need to understand and fix those first.
Revert "i2c: rcar: clean up after refactoring"
Revert "i2c: rcar: revoke START request early"
Revert "i2c: rcar: check master irqs before slave irqs"
Revert "i2c: rcar: don't issue stop when HW does it automatically"
Revert "i2c: rcar: init new messages in irq"
Revert "i2c: rcar: refactor setup of a msg"
Revert "i2c: rcar: remove spinlock"
Revert "i2c: rcar: remove unused IOERROR state"
Revert "i2c: rcar: rework hw init"
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add missing entries into i2c-i801 documentation and Kconfig about recently
added Intel DNV and Broxton.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
