They report 40bit, but only have 36bits of physical address space.
This caused problems with setting up the correct masks for MTRR.
CPUID workaround for steppings 0F33h(supporting x86) and 0F34h(supporting x86
and EM64T). Detail info can be found at:
http://download.intel.com/design/Xeon/specupdt/30240216.pdfhttp://download.intel.com/design/Pentium4/specupdt/30235221.pdf
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Compute the highest possible value for memnode_shift, in order to reduce
footprint of memnodemap[] to the minimum, thus making all users
(phys_to_nid(), kfree()), more cache friendly.
Before the patch :
Node 0 MemBase 0000000000000000 Limit 00000001ffffffff
Node 1 MemBase 0000000200000000 Limit 00000003ffffffff
Using 23 for the hash shift. Max adder is 3ffffffff
After the patch :
Node 0 MemBase 0000000000000000 Limit 00000001ffffffff
Node 1 MemBase 0000000200000000 Limit 00000003ffffffff
Using 33 for the hash shift.
In this case, only 2 bytes of memnodemap[] are used, instead of 2048
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows to run 64bit signal handlers in 64bit processes that run small
code snippets in compat mode.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With a NR_CPUS==128 kernel with CPU hotplug enabled we would waste 4MB
on per CPU data of all possible CPUs. The reason was that HOTPLUG
always set up possible map to NR_CPUS cpus and then we need to allocate
that much (each per CPU data is roughly ~32k now)
The underlying problem is that ACPI didn't tell us how many hotplug CPUs
the platform supports. So the old code just assumed all, which would
lead to this memory wastage.
This implements some new heuristics:
- If the BIOS specified disabled CPUs in the ACPI/mptables assume they
can be enabled later (this is bending the ACPI specification a bit,
but seems like a obvious extension)
- The user can overwrite it with a new additionals_cpus=NUM option
- Otherwise use half of the available CPUs or 2, whatever is more.
Cc: ashok.raj@intel.com
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor victory on the continuous quest against all stray extern.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adding __initdata_* to asm-generic/sections.h
Replaces a lot of open coded externs in arch/x86_64/*
I had to change __bss_end to __bss_stop to match the other architectures.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should zap the low mappings, as soon as possible, so that we can catch
kernel bugs more effectively. Previously early boot had NULL mapped
and didn't trap on NULL references.
This patch introduces boot_level4_pgt, which will always have low identity
addresses mapped. Druing boot, all the processors will use this as their
level4 pgt. On BP, we will switch to init_level4_pgt as soon as we enter C
code and zap the low mappings as soon as we are done with the usage of
identity low mapped addresses. On AP's we will zap the low mappings as
soon as we jump to C code.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not go from the CPU number to an mapping array.
Mode number is often used now in fast paths.
This also adds a generic numa_node_id to all the topology includes
Suggested by Eric Dumazet
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix
arch/x86_64/kernel/aperture.c: In function #iommu_hole_init#:
arch/x86_64/kernel/aperture.c:199: warning: #aper_order# may be used uninitialized in this function
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to cpuid instruction in IA32 SDM-Vol2, when computing cpu model,
we need to consider extended model ID for family 0x6 also.
AK: Also added fixes/simplifcation from Petr Vandrovec
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove duplicate __cpuinit in smp.c. Already defined in init.h which is
already included.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's a patch that builds on Natalie Protasevich's IRQ compression
patch and tries to work for MPS boots as well as ACPI. It is meant for
a 4-node IBM x460 NUMA box, which was dying because it had interrupt
pins with GSI numbers > NR_IRQS and thus overflowed irq_desc.
The problem is that this system has 270 GSIs (which are 1:1 mapped with
I/O APIC RTEs) and an 8-node box would have 540. This is much bigger
than NR_IRQS (224 for both i386 and x86_64). Also, there aren't enough
vectors to go around. There are about 190 usable vectors, not counting
the reserved ones and the unused vectors at 0x20 to 0x2F. So, my patch
attempts to compress the GSI range and share vectors by sharing IRQs.
Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MC4_MISC - DRAM Errors Threshold Register realized under AMD K8 Rev F.
This register is used to count correctable and uncorrectable ECC errors that occur during DRAM read operations.
The user may interface through sysfs files in order to change the threshold configuration.
bank%d/error_count - reads current error count, write to clear.
bank%d/interrupt_enable - set/clear interrupt enable.
bank%d/threshold_limit - read/write the threshold limit.
APIC vector 0xF9 in hw_irq.h.
5 software defined bank ids in mce.h.
new apic.c function to setup threshold apic lvt.
defaults to interrupt off, count enabled, and threshold limit max.
sysfs interface created on /sys/devices/system/threshold.
AK: added some ifdefs to make it compile on UP
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The VM needs to know about lost memory in zones to accurately
balance dirty pages. This patch accounts mem_map in there too,
which fixes a constant errror of a few percent. Also some
other misc mappings and the kernel text itself are accounted
too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new 4GB GFP_DMA32 zone between the GFP_DMA and GFP_NORMAL zones.
As a bit of historical background: when the x86-64 port
was originally designed we had some discussion if we should
use a 16MB DMA zone like i386 or a 4GB DMA zone like IA64 or
both. Both was ruled out at this point because it was in early
2.4 when VM is still quite shakey and had bad troubles even
dealing with one DMA zone. We settled on the 16MB DMA zone mainly
because we worried about older soundcards and the floppy.
But this has always caused problems since then because
device drivers had trouble getting enough DMA able memory. These days
the VM works much better and the wide use of NUMA has proven
it can deal with many zones successfully.
So this patch adds both zones.
This helps drivers who need a lot of memory below 4GB because
their hardware is not accessing more (graphic drivers - proprietary
and free ones, video frame buffer drivers, sound drivers etc.).
Previously they could only use IOMMU+16MB GFP_DMA, which
was not enough memory.
Another common problem is that hardware who has full memory
addressing for >4GB misses it for some control structures in memory
(like transmit rings or other metadata). They tended to allocate memory
in the 16MB GFP_DMA or the IOMMU/swiotlb then using pci_alloc_consistent,
but that can tie up a lot of precious 16MB GFPDMA/IOMMU/swiotlb memory
(even on AMD systems the IOMMU tends to be quite small) especially if you have
many devices. With the new zone pci_alloc_consistent can just put
this stuff into memory below 4GB which works better.
One argument was still if the zone should be 4GB or 2GB. The main
motivation for 2GB would be an unnamed not so unpopular hardware
raid controller (mostly found in older machines from a particular four letter
company) who has a strange 2GB restriction in firmware. But
that one works ok with swiotlb/IOMMU anyways, so it doesn't really
need GFP_DMA32. I chose 4GB to be compatible with IA64 and because
it seems to be the most common restriction.
The new zone is so far added only for x86-64.
For other architectures who don't set up this
new zone nothing changes. Architectures can set a compatibility
define in Kconfig CONFIG_DMA_IS_DMA32 that will define GFP_DMA32
as GFP_DMA. Otherwise it's a nop because on 32bit architectures
it's normally not needed because GFP_NORMAL (=0) is DMA able
enough.
One problem is still that GFP_DMA means different things on different
architectures. e.g. some drivers used to have #ifdef ia64 use GFP_DMA
(trusting it to be 4GB) #elif __x86_64__ (use other hacks like
the swiotlb because 16MB is not enough) ... . This was quite
ugly and is now obsolete.
These should be now converted to use GFP_DMA32 unconditionally. I haven't done
this yet. Or best only use pci_alloc_consistent/dma_alloc_coherent
which will use GFP_DMA32 transparently.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
attached patch renames one instance of
/sys/devices/system/timer
to
/sys/devices/system/timer_pit
to avoid a name clash with another instance created in time.c.
Acked-by: Andi Kleen <ak@muc.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid. Improves efficiency of
resched_task and some cpu_idle routines.
* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
and as we hold it during resched_task, then there is no need for an
atomic test and set there. The only other time this should be set is
when the task's quantum expires, in the timer interrupt - this is
protected against because the rq lock is irq-safe.
- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
won't get unset until the task get's schedule()d off.
- If we are running on the same CPU as the task we resched, then set
TIF_NEED_RESCHED and no further action is required.
- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
after TIF_NEED_RESCHED has been set, then we need to send an IPI.
Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.
* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
becomes true, explicitly call schedule(). This makes things a bit clearer
(IMO), but haven't updated all architectures yet.
- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
to the resched_task rules, this isn't needed (and actually breaks the
assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
held). So remove that. Generally one less locked memory op when switching
to the idle thread.
- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
most polling idle loops. The above resched_task semantics allow it to be
set until before the last time need_resched() is checked before going into
a halt requiring interrupt wakeup.
Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
can be always left set, completely eliminating resched IPIs when rescheduling
the idle task.
POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run idle threads with preempt disabled.
Also corrected a bugs in arm26's cpu_idle (make it actually call schedule()).
How did it ever work before?
Might fix the CPU hotplugging hang which Nigel Cunningham noted.
We think the bug hits if the idle thread is preempted after checking
need_resched() and before going to sleep, then the CPU offlined.
After calling stop_machine_run, the CPU eventually returns from preemption and
into the idle thread and goes to sleep. The CPU will continue executing
previous idle and have no chance to call play_dead.
By disabling preemption until we are ready to explicitly schedule, this bug is
fixed and the idle threads generally become more robust.
From: alexs <ashepard@u.washington.edu>
PPC build fix
From: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
MIPS build fix
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EXPORT_SYMBOL's for phys_proc_id and cpu_core_id were added this year but
never used.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reorganize the preempt_disable/enable calls to eliminate the extra preempt
depth. Changes based on Paul McKenney's review suggestions for the kprobes
RCU changeset.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes to the arch kprobes infrastructure to take advantage of the locking
changes introduced by usage of RCU for synchronization. All handlers are now
run without any locks held, so they have to be re-entrant or provide their own
synchronization.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86_64 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu using a arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following set of patches are aimed at improving kprobes scalability. We
currently serialize kprobe registration, unregistration and handler execution
using a single spinlock - kprobe_lock.
With these changes, kprobe handlers can run without any locks held. It also
allows for simultaneous kprobe handler executions on different processors as
we now track kprobe execution on a per processor basis. It is now necessary
that the handlers be re-entrant since handlers can run concurrently on
multiple processors.
All changes have been tested on i386, ia64, ppc64 and x86_64, while sparc64
has been compile tested only.
The patches can be viewed as 3 logical chunks:
patch 1: Reorder preempt_(dis/en)able calls
patches 2-7: Introduce per_cpu data areas to track kprobe execution
patches 8-9: Use RCU to synchronize kprobe (un)registration and handler
execution.
Thanks to Maneesh Soni, James Keniston and Anil Keshavamurthy for their
review and suggestions. Thanks again to Anil, Hien Nguyen and Kevin Stafford
for testing the patches.
This patch:
Reorder preempt_disable/enable() calls in arch kprobes files in preparation to
introduce locking changes. No functional changes introduced by this patch.
Signed-off-by: Ananth N Mavinakayahanalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The sys_ptrace boilerplate code (everything outside the big switch
statement for the arch-specific requests) is shared by most architectures.
This patch moves it to kernel/ptrace.c and leaves the arch-specific code as
arch_ptrace.
Some architectures have a too different ptrace so we have to exclude them.
They continue to keep their implementations. For sh64 I had to add a
sh64_ptrace wrapper because it does some initialization on the first call.
For um I removed an ifdefed SUBARCH_PTRACE_SPECIAL block, but
SUBARCH_PTRACE_SPECIAL isn't defined anywhere in the tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-By: David Howells <dhowells@redhat.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton suggested to move kprobes from kernel hacking menu, since
kernel hacking menu is in-appropriate for the Kprobes. This patch moves
Kprobes and Oprofile under instrumentation menu.
(akpm: it's not a natural fit, but things like djprobes and the s390 guys'
statistics library need a home)
Signed-of-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: John Levon <levon@movementarian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes the x86-64 find_[first|next]_zero_bit() function for the
end-of-range case. It didn't test for a zero size, and the "rep scas"
would do entirely the wrong thing.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reads from an HPET register require a round trip to the south bridge and are
almost as slow as PCI reads. By caching the last value we've written to the
comparator register, we can eliminate all HPET reads from the fast path in the
emulated RTC interrupt handler.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure that the RTC timer is in non-periodic mode; some stupid BIOS might
have initialized it to periodic mode.
Furthermore, don't set the SETVAL bit in the config register. This wouldn't
have any effect unless the timer was in period mode (which it isn't), and then
the actual timer frequency would be half that of the desired one because
incrementing the comparator in the interrupt handler would be done after the
hardware has already incremented it itself.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the emulated RTC interrupt is no longer needed, we better disable it;
otherwise, we get a spurious interrupt whenever the timer has rolled over and
reaches the same comparator value.
Having a superfluous interrupt every five minutes doesn't hurt much, but it's
bad style anyway. ;-)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define jiffies_64 in kernel/timer.c rather than having 24 duplicated
defines in each architecture.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This ioctl doesn't exist for native i386.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every user of init_timer() also needs to initialize ->function and ->data
fields. This patch adds a simple setup_timer() helper for that.
The schedule_timeout() is patched as an example of usage.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch makes swsusp use the PG_nosave and PG_nosave_free flags to
mark pages that should be freed in case of an error during resume.
This allows us to simplify the code and to use swsusp_free() in all of the
swsusp's resume error paths, which makes them actually work.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle 32-bit mtrr ioctls in the mtrr driver instead of the ia32
compatability layer.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If VMX feature is available in the CPU, this patch will make it visible in
the /proc/cpuinfo with the cpuid detection.
Signed-Off-By: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mxcsr_feature_mask_init isn't needed in suspend/resume time (we can use
boot time mask). And actually it's harmful, as it clear task's saved
fxsave in resume. This bug is widely seen by users using zsh.
(akpm: my eyes. Fixed some surrounding whitespace mess)
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I just found out that some precision is unnecessarily lost in the
arch/i386/kernel/timers/timer_tsc.c:set_cyc2ns_scale function. It uses a
cpu_mhz parameter when it could use a cpu_khz. In the specific case of an
Intel P4 running at 3001.171 Mhz, the truncation to 3001 Mhz leads to an
imprecision of 19 microseconds per second : this is very sad for a timer with
nearly nanosecond accuracy.
Fix the x86_64 architecture too.
Cc: george anzinger <george@mvista.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
First step in pushing down the page_table_lock. init_mm.page_table_lock has
been used throughout the architectures (usually for ioremap): not to serialize
kernel address space allocation (that's usually vmlist_lock), but because
pud_alloc,pmd_alloc,pte_alloc_kernel expect caller holds it.
Reverse that: don't lock or unlock init_mm.page_table_lock in any of the
architectures; instead rely on pud_alloc,pmd_alloc,pte_alloc_kernel to take
and drop it when allocating a new one, to check lest a racing task already
did. Similarly no page_table_lock in vmalloc's map_vm_area.
Some temporary ugliness in __pud_alloc and __pmd_alloc: since they also handle
user mms, which are converted only by a later patch, for now they have to lock
differently according to whether or not it's init_mm.
If sources get muddled, there's a danger that an arch source taking
init_mm.page_table_lock will be mixed with common source also taking it (or
neither take it). So break the rules and make another change, which should
break the build for such a mismatch: remove the redundant mm arg from
pte_alloc_kernel (ppc64 scrapped its distinct ioremap_mm in 2.6.13).
Exceptions: arm26 used pte_alloc_kernel on user mm, now pte_alloc_map; ia64
used pte_alloc_map on init_mm, now pte_alloc_kernel; parisc had bad args to
pmd_alloc and pte_alloc_kernel in unused USE_HPPA_IOREMAP code; ppc64
map_io_page forgot to unlock on failure; ppc mmu_mapin_ram and ppc64 im_free
took page_table_lock for no good reason.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
How is anon_rss initialized? In dup_mmap, and by mm_alloc's memset; but
that's not so good if an mm_counter_t is a special type. And how is rss
initialized? By set_mm_counter, all over the place. Come on, we just need to
initialize them both at once by set_mm_counter in mm_init (which follows the
memcpy when forking).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
changes to swiotlb.c made in commit 281dd25cdc0d6903929b79183816d151ea626341
since this file has been moved from arch/ia64/lib/swiotlb.c to
lib/swiotlb.c
Signed-off-by: Tony Luck <tony.luck@intel.com>
CPU hotplug fills up the possible map to NR_CPUs, but it did that after
setting up per CPU data. This lead to CPU data not getting allocated
for all possible CPUs, which lead to various side effects.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noticed by Terence Ripperda
Undo wrong change in global_flush_tlb. We need to flush the caches in all
cases, not just when pages were reverted. This was a bogus optimization
added earlier, but it was wrong.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes the setup of the alignment of the signal frame, so that all
signal handlers are run with a properly aligned stack frame.
The current code "over-aligns" the stack pointer so that the stack frame
is effectively always mis-aligned by 4 bytes. But what we really want
is that on function entry ((sp + 4) & 15) == 0, which matches what would
happen if the stack were aligned before a "call" instruction.
Signed-off-by: Markus F.X.J. Oberhumer <markus@oberhumer.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch makes swsusp avoid the possible temporary corruption
of page translation tables during resume on x86-64. This is achieved by
creating a copy of the relevant page tables that will not be modified by
swsusp and can be safely used by it on resume.
The problem is that during resume on x86-64 swsusp may temporarily
corrupt the page tables used for the direct mapping of RAM. If that
happens, a page fault occurs and cannot be handled properly, which leads
to the solid hang of the affected system. This leads to the loss of the
system's state from before suspend and may result in the loss of data or
the corruption of filesystems, so it is a serious issue. Also, it
appears to happen quite often (for me, as often as 50% of the time).
The problem is related to the fact that (at least) one of the PMD
entries used in the direct memory mapping (starting at PAGE_OFFSET)
points to a page table the physical address of which is much greater
than the physical address of the PMD entry itself. Moreover,
unfortunately, the physical address of the page table before suspend
(i.e. the one stored in the suspend image) happens to be different to
the physical address of the corresponding page table used during resume
(i.e. the one that is valid right before swsusp_arch_resume() in
arch/x86_64/kernel/suspend_asm.S is executed). Thus while the image is
restored, the "offending" PMD entry gets overwritten, so it does not
point to the right physical address any more (i.e. there's no page
table at the address pointed to by it, because it points to the address
the page table has been at during suspend). Consequently, if the PMD
entry is used later on, and it _is_ used in the process of copying the
image pages, a page fault occurs, but it cannot be handled in the normal
way and the system hangs.
In principle we can call create_resume_mapping() from
swsusp_arch_resume() (ie. from suspend_asm.S), but then the memory
allocations in create_resume_mapping(), resume_pud_mapping(), and
resume_pmd_mapping() must be made carefully so that we use _only_
NosaveFree pages in them (the other pages are overwritten by the loop in
swsusp_arch_resume()). Additionally, we are in atomic context at that
time, so we cannot use GFP_KERNEL. Moreover, if one of the allocations
fails, we should free all of the allocated pages, so we need to trace
them somehow.
All of this is done in the appended patch, except that the functions
populating the page tables are located in arch/x86_64/kernel/suspend.c
rather than in init.c. It may be done in a more elegan way in the
future, with the help of some swsusp patches that are in the works now.
[AK: move some externs into headers, renamed a function]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
