Due to SNDRV_SEQ_ADDRESS_BROADCAST, not all 256 port number values can
be used.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the last subscriber to a "Through" port has been removed, the
subscribed destination ports might still be active, so it would be
wrong to send "all sounds off" and "reset controller" events to them.
The proper place for such a shutdown would be the closing of the actual
MIDI port (and close_substream() in rawmidi.c already can do this).
This also fixes a deadlock when dummy_unuse() tries to send events to
its own port that is already locked because it is being freed.
Reported-by: Peter Billam <peter@www.pjb.com.au>
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_midi_event_free() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add SNDRV_PCM_TRIGGER_DRAIN trigger for pcm drain.
Some audio devices require notification of drain events
in order to properly drain and shutdown an audio stream.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of opencoding them use the standard roundup_pow_of_two() and
rounddown_pow_of_two() helper functions. This gets rids one of the few users
of the custom ld2() function and also makes it a bit more obvious what the
code does.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the msbits constraints requires to specify a specific sample
format width for which the constraint should be applied. But often the
number of most significant bits is not sample format specific, but rather a
absolute limit. E.g. the PCM interface might accept 32-bit and 24-bit
samples, but the DAC has a 16-bit resolution and throws away the LSBs. In
this case for both 32-bit and 24-bit format msbits should be set to 16. This
patch extends snd_pcm_hw_constraint_msbits() so that a wildcard constraint
can be setup that is applied for all formats with a sample width larger than
the specified msbits. Choosing the wildcard constraint is done by setting
the sample width parameter of the function to 0.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the sound card is made up of discrete components, each with their own
driver (e.g. like in the ASoC case), we might end up with multiple msbits
constraint rules installed. Currently this will result in msbits being set
to whatever the last rule set it to.
This patch updates the behavior of the rule to choose the minimum (other
than zero) of all the installed rules.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [7a2e9ddc: ALSA: usb-audio: Add native DSD support for
Denon/Marantz DACs] requires the new format definition that has
landed only in for-next branch.
The functions snd_seq_oss_timer_delete() and vunmap() perform also input
parameter validation. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes XMOS DSD sample format to DSD_U32_BE and also adds
DSD_U16_BE and DSD_U32_BE sample formats.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Acked-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a copy & paste error:
Warning(sound/core/pcm_native.c:1112): Excess function parameter 'state' description in 'snd_pcm_stop_xrun'
The state argument was dropped from snd_pcm_stop_xrun().
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new helper function snd_pcm_stop_xrun() to the standard sequnce
lock/snd_pcm_stop(XRUN)/unlock by a single call, and replace the
existing open codes with this helper.
The function checks the PCM running state to prevent setting the wrong
state, too, for more safety.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We want to know the offset for the id that was passed to the function, not
the offset of the first id of the control (which is always 0).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some state changes (e.g. snd_pcm_stop()) sets the runtime state after
calling snd_timer_notify(). This is basically racy, since the
notification may wakes up the user even before the state change.
Although the possibility is low, we should set the state before the
notifications.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges the USB-audio disconnect fix and resolves the conflicts
so that we can continue working on development of usb-audio stuff.
Conflicts:
sound/usb/card.c
This patch adds a new proc entry for PCM substreams to inject an
XRUN. When a PCM substream is running and any value is written to its
xrun_injection proc file, the driver triggers XRUN. This is a useful
feature for debugging XRUN and error handling code paths.
Note that this entry is enabled only when CONFIG_SND_PCM_XRUN_DEBUG is
set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA PCM core has a mechanism tracking the PCM hwptr updates for
analyzing XRUNs. But its log is limited (up to 10) and its log output
is a kernel message, which is hard to handle.
In this patch, the hwptr logging is moved to the tracing
infrastructure instead of its own. Not only the hwptr updates but
also XRUN and hwptr errors are recorded on the trace log, so that user
can see such events at the exact timing.
The new "snd_pcm" entry will appear in the tracing events:
# ls -F /sys/kernel/debug/tracing/events/snd_pcm
enable filter hw_ptr_error/ hwptr/ xrun/
The hwptr is for the regular hwptr update events. An event trace
looks like:
aplay-26187 [004] d..3 4012.834761: hwptr: pcmC0D0p/sub0: POS: pos=488, old=0, base=0, period=1024, buf=16384
"POS" shows the hwptr update by the explicit position update call and
"IRQ" means the hwptr update by the interrupt,
i.e. snd_pcm_period_elapsed() call. The "pos" is the passed
ring-buffer offset by the caller, "old" is the previous hwptr, "base"
is the hwptr base position, "period" and "buf" are period- and
buffer-size of the target PCM substream.
(Note that the hwptr position displayed here isn't the ring-buffer
offset. It increments up to the PCM position boundary.)
The XRUN event appears similarly, but without "pos" field.
The hwptr error events appear with the PCM identifier and its reason
string, such as "Lost interrupt?".
The XRUN and hwptr error reports on kernel message are still left, can
be turned on/off via xrun_debug proc like before. But the bit 3, 4, 5
and 6 bits of xrun_debug proc are dropped by this patch. Also, along
with the change, the message strings have been reformatted to be a bit
more consistent.
Last but not least, the hwptr reporting is enabled only when
CONFIG_SND_PCM_XRUN_DEBUG is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While converting to dev_*(), the message showing the invalid PCM
position was wrongly tagged as if an XRUN although it's actually a
BUG. This patch corrects the message again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function snd_pcm_action_lock_irq() can be much simplified by
simply wrapping snd_pcm_action() with the stream lock. This was
rather the original idea, but later it was open coded for
optimization. However, looking at the optimization part closely, one
notices that the probability of the optimized path is quite low; in
normal situations, the linked stream action happens only for the
triggered substream, thus the operation becomes identical. So the
code simplification has a clear win, especially because we have now
doubly codes for both atomic and non-atomic locks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few functions have no proper documentation yet, so let's add them.
Along with it, remove superfluous blank line between the closing brace
and EXPORT_SYMBOL() line.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In compat mode, we copy each field of snd_pcm_status struct but don't
touch the reserved fields, and this leaves uninitialized values
there. Meanwhile the native ioctl does zero-clear the whole
structure, so we should follow the same rule in compat mode, too.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On x86, using dma_mmap_coherent() for the pages allocated via
dma_alloc_coherent() results in a warning like:
aplay:32536 map pfn RAM range req uncached-minus for [mem 0x21d500000-0x21d51ffff], got write-back
Until the issue is addressed in the core side, take back to the old
good way in PCM code only for x86.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
this is a series of patches to just convert the plain info callback
for enum ctl elements to snd_ctl_elem_info(). Also, it includes the
extension of snd_ctl_elem_info(), for catching the unexpected string
cut-off and handling the zero items.
Some architectures like PARISC is known not to support mmap properly
with the DMA buffer, where dma_mmap_coherent() returns -EINVAL
unconditionally. From the API POV, we should rather drop the mmap
support there and expose it before the user-space tries to call mmap.
The patch contains again ugly ifdef's, unfortunately, as there is no
global flag indicating this. Once when such macro is defined, we can
get rid of this instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since we have consistently dma_mmap_coherent() for all architectures,
the current ifdef and arch-specific codes in pcm core can be cleaned
up gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As PCM core handles the multiple linked streams in parallel, lockdep
gets confused (partly because of weak annotations) and spews the
false-positive warnings. This hasn't been a problem for long time but
the latest PCM lock path update seems to have woken up a sleeping
dog.
Here is an attempt to paper over this issue: pass the lock subclass
just calculated from the depth in snd_pcm_action_group(). Also, a
(possibly) wrong lock subclass set in snd_pcm_action_lock_mutex() is
dropped, too.
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although this is weird, some drivers want to allow empty control
elements intentionally, e.g. the number of items may change depending
on the firmware status. Let the function simply returning in such a
case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since we're calling request_module() asynchronously now, we can get
rid of the autoload lock in snd_seq_device_register_driver(), as well
as in the snd-seq driver registration itself. This enables the
automatic loading of dependent sequencer modules, such as
snd-seq-virmidi from snd-emu10k1-synth.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the sequencer module binding is performed independently from
the card module itself. The reason behind it is to keep the sequencer
stuff optional and allow the system running without it (e.g. for using
PCM or rawmidi only). This works in most cases, but a remaining
problem is that the binding isn't done automatically when a new driver
module is probed. Typically this becomes visible when a hotplug
driver like usb audio is used.
This patch tries to address this and other potential issues. First,
the seq-binder (seq_device.c) tries to load a missing driver module at
creating a new device object. This is done asynchronously in a workq
for avoiding the deadlock (modprobe call in module init path).
This action, however, should be enabled only when the sequencer stuff
was already initialized, i.e. snd-seq module was already loaded. For
that, a new function, snd_seq_autoload_init() is introduced here; this
clears the blocking of autoloading, and also tries to load all pending
driver modules.
Reported-by: Adam Goode <agoode@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the unlock loop of snd_pcm_action_group(), the object "s" is used
as the check of nonatomic PCM, but it should be rather "s1", which is
the iterator of the loop. This supposedly causes a kernel panic when
the substreams in operatino are linked.
Fixes: 257f8cce5d ('ALSA: pcm: Allow nonatomic trigger operations')
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a NULL check in snd_pci_quirk_lookup() so that NULL can be passed
as a pci_dev pointer. This fixes the possible NULL dereferences in
HD-audio drivers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- More componentisation work from Lars-Peter, this time mainly
cleaning up the suspend and bias level transition callbacks.
- Real system support for the Intel drivers and a bunch of fixes and
enhancements for the associated CODEC drivers, this is going to need
a lot quirks over time due to the lack of any firmware description of
the boards.
- Jack detect support for simple card from Dylan Reid.
- A bunch of small fixes and enhancements for the Freescale drivers.
- New drivers for Analog Devices SSM4567, Cirrus Logic CS35L32, Everest
Semiconductor ES8328 and Freescale cards using the ASRC in newer i.MX
processors.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUMoHRAAoJECTWi3JdVIfQGXUH/RWQ6/Ey70SPgUdWWQ42PFey
sBq/Hl69F8/JNxW6EDA4GEg6ue880Gek0oGqioxtN6Ku0Vm/WSqDWnKcTAGl4dDO
AefC4FwekZWCYQi3VTNIvMEqfUWkcofTLVwjdh/PUZxniahkiGA81UJ1mQNXBxLF
UusrK0fIAxQgiNsCcPZ94knJiqZVBWgbRv/mCXY9K1/jqITNKd/ZVEMkOPk/p00q
cH9LIx8EknRV3HyJNZQ0xpmhpuMzLy6Agf7Oeq/m5kDqq1stmClvibPYkdqkdkto
jYwKaPh18dNHlUmm1w/G7X20kCidhbiwRjS/iIzx3cfIrWkiz90/BSRFKs8pqSo=
=7PPg
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.18
- More componentisation work from Lars-Peter, this time mainly
cleaning up the suspend and bias level transition callbacks.
- Real system support for the Intel drivers and a bunch of fixes and
enhancements for the associated CODEC drivers, this is going to need
a lot quirks over time due to the lack of any firmware description of
the boards.
- Jack detect support for simple card from Dylan Reid.
- A bunch of small fixes and enhancements for the Freescale drivers.
- New drivers for Analog Devices SSM4567, Cirrus Logic CS35L32, Everest
Semiconductor ES8328 and Freescale cards using the ASRC in newer i.MX
processors.
The calculated frame size was wrong because snd_pcm_format_physical_width()
actually returns the number of bits, not bytes.
Use snd_pcm_format_size() instead, which not only returns bytes, but also
simplifies the calculation.
Fixes: 8bea869c5e ("ALSA: PCM midlevel: improve fifo_size handling")
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
