This provides the low-level support for MMIO emulation in Book3S HV
guests. When the guest tries to map a page which is not covered by
any memslot, that page is taken to be an MMIO emulation page. Instead
of inserting a valid HPTE, we insert an HPTE that has the valid bit
clear but another hypervisor software-use bit set, which we call
HPTE_V_ABSENT, to indicate that this is an absent page. An
absent page is treated much like a valid page as far as guest hcalls
(H_ENTER, H_REMOVE, H_READ etc.) are concerned, except of course that
an absent HPTE doesn't need to be invalidated with tlbie since it
was never valid as far as the hardware is concerned.
When the guest accesses a page for which there is an absent HPTE, it
will take a hypervisor data storage interrupt (HDSI) since we now set
the VPM1 bit in the LPCR. Our HDSI handler for HPTE-not-present faults
looks up the hash table and if it finds an absent HPTE mapping the
requested virtual address, will switch to kernel mode and handle the
fault in kvmppc_book3s_hv_page_fault(), which at present just calls
kvmppc_hv_emulate_mmio() to set up the MMIO emulation.
This is based on an earlier patch by Benjamin Herrenschmidt, but since
heavily reworked.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently we patch the whole code include paravirt template code.
This isn't safe for scratch area and has impact to performance.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This allows additional registers to be accessed by the guest
in PR-mode KVM without trapping.
SPRG4-7 are readable from userspace. On booke, KVM will sync
these registers when it enters the guest, so that accesses from
guest userspace will work. The guest kernel, OTOH, must consistently
use either the real registers or the shared area between exits. This
also applies to the already-paravirted SPRG3.
On non-booke, it's not clear to what extent SPRG4-7 are supported
(they're not architected for book3s, but exist on at least some classic
chips). They are copied in the get/set regs ioctls, but I do not see any
non-booke emulation. I also do not see any syncing with real registers
(in PR-mode) including the user-readable SPRG3. This patch should not
make that situation any worse.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Also fix wrteei 1 paravirt to check for a pending interrupt.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The current implementation of mtmsr and mtmsrd are racy in that it does:
* check (int_pending == 0)
---> host sets int_pending = 1 <---
* write shared page
* done
while instead we should check for int_pending after the shared page is written.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Create a distinction between scheduler related preempt_enable_no_resched()
calls and the nearly one hundred other places in the kernel that do not
want to reschedule, for one reason or another.
This distinction matters for -rt, where the scheduler and the non-scheduler
preempt models (and checks) are different. For upstream it's purely
documentational.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/n/tip-gs88fvx2mdv5psnzxnv575ke@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With bug.h currently living right in linux/kernel.h there
are files that use BUG_ON and friends but are not including
the header explicitly. Fix them up so we can remove the
presence in kernel.h file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We already use pci_flags, so this just sets pci_flags directly and removes
the intermediate step of figuring out pci_probe_only, then using it to set
pci_flags.
The PCI core provides a pci_flags definition (currently __weak), so drop
the powerpc definitions in favor of that.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_probe_only is set on ppc64 to prevent resource re-allocation
by the core. It's meant to be used in very specific circumstances
such as when operating under a hypervisor that may prevent such
re-allocation.
Instead of default to 1, we make it default to 0 and explicitly
set it in the few cases where we need it.
This fixes FSL PCI which wants it clear among others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The perf code has grown a lot since it started, and is big enough to
warrant its own subdirectory. For reference it's ~60% bigger than the
oprofile code. It declutters the kernel directory, makes it simpler to
grep for "just perf stuff", and allows us to shorten some filenames.
While we're at it, make it more obvious that we have two implementations
of the core perf logic. One for (roughly) Book3S CPUs, which was the
original implementation, and the other for Freescale embedded CPUs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the phyp assisted dump implementation which is not is use.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If dump is active during system reboot, shutdown or halt then invalidate
the fadump registration as it does not get invalidated automatically.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch introduces an sysfs interface '/sys/kernel/fadump_release_mem' to
invalidate the last fadump registration, invalidate '/proc/vmcore', release
the reserved memory for general use and re-register for future kernel dump.
Once the dump is copied to the disk, unlike phyp dump, the userspace tool
can release all the memory reserved for dump with one single operation of
echo 1 to '/sys/kernel/fadump_release_mem'.
Release the reserved memory region excluding the size of the memory required
for future kernel dump registration. And therefore, unlike kdump, Fadump
doesn't need a 2nd reboot to get back the system to the production
configuration.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Introduce a PT_NOTE program header that points to physical address of
vmcoreinfo_note buffer declared in kernel/kexec.c. The vmcoreinfo
note buffer is populated during crash_fadump() at the time of system
crash.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When registered for firmware assisted dump on powerpc, firmware preserves
the registers for the active CPUs during a system crash. This patch reads
the cpu register data stored in Firmware-assisted dump format (except for
crashing cpu) and converts it into elf notes and updates the PT_NOTE program
header accordingly. The exact register state for crashing cpu is saved to
fadump crash info structure in scratch area during crash_fadump() and read
during second kernel boot.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Build the crash memory range list by traversing through system memory during
the first kernel before we register for firmware-assisted dump. After the
successful dump registration, initialize the elfcore header and populate
PT_LOAD program headers with crash memory ranges. The elfcore header is
saved in the scratch area within the reserved memory. The scratch area starts
at the end of the memory reserved for saving RMR region contents. The
scratch area contains fadump crash info structure that contains magic number
for fadump validation and physical address where the eflcore header can be
found. This structure will also be used to pass some important crash info
data to the second kernel which will help second kernel to populate ELF core
header with correct data before it gets exported through /proc/vmcore. Since
the firmware preserves the entire partition memory at the time of crash the
contents of the scratch area will be preserved till second kernel boot.
Since the memory dump exported through /proc/vmcore is in ELF format similar
to kdump, it will help us to reuse the kdump infrastructure for dump capture
and filtering. Unlike phyp dump, userspace tool does not need to refer any
sysfs interface while reading /proc/vmcore.
NOTE: The current design implementation does not address a possibility of
introducing additional fields (in future) to this structure without affecting
compatibility. It's on TODO list to come up with better approach to
address this.
Reserved dump area start => +-------------------------------------+
| CPU state dump data |
+-------------------------------------+
| HPTE region data |
+-------------------------------------+
| RMR region data |
Scratch area start => +-------------------------------------+
| fadump crash info structure { |
| magic nummber |
+------|---- elfcorehdr_addr |
| | } |
+----> +-------------------------------------+
| ELF core header |
Reserved dump area end => +-------------------------------------+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On 2012-02-20 11:02:51 Mon, Paul Mackerras wrote:
> On Thu, Feb 16, 2012 at 04:44:30PM +0530, Mahesh J Salgaonkar wrote:
>
> If I have read the code correctly, we are going to get this printk on
> non-pSeries machines or on older pSeries machines, even if the user
> has not put the fadump=on option on the kernel command line. The
> printk will be annoying since there is no actual error condition. It
> seems to me that the condition for the printk should include
> fw_dump.fadump_enabled. In other words you should probably add
>
> if (!fw_dump.fadump_enabled)
> return 0;
>
> at the beginning of the function.
Hi Paul,
Thanks for pointing it out. Please find the updated patch below.
The existing patches above this (4/10 through 10/10) cleanly applies
on this update.
Thanks,
-Mahesh.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reserve the memory during early boot to preserve CPU state data, HPTE region
and RMA (real mode area) region data in case of kernel crash. At the time of
crash, powerpc firmware will store CPU state data, HPTE region data and move
RMA region data to the reserved memory area.
If the firmware-assisted dump fails to reserve the memory, then fallback
to existing kexec-based kdump.
Most of the code implementation to reserve memory has been
adapted from phyp assisted dump implementation written by Linas Vepstas
and Manish Ahuja
This patch also introduces a config option CONFIG_FA_DUMP for firmware
assisted dump feature on Powerpc (ppc64) architecture.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a few problems when returning to userspace. This is a
quick set of fixes for 3.3, I'll look into a more comprehensive
rework for 3.4. This fixes:
- We kept interrupts soft-disabled when schedule'ing or calling
do_signal when returning to userspace as a result of a hardware
interrupt.
- Rename do_signal to do_notify_resume like all other archs (and
do_signal_pending back to do_signal, which it was before Roland
changed it).
- Add the missing call to key_replace_session_keyring() to
do_notify_resume().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
In commit 54321242af ("Disable interrupts early in Program Check"), we
switched from enabling to disabling interrupts in program_check_common.
Whereas ENABLE_INTS leaves r3 untouched, if lockdep is enabled DISABLE_INTS
calls into lockdep code and will clobber r3. That means we pass a bogus
struct pt_regs* into program_check_exception() and all hell breaks loose.
So load our regs pointer into r3 after we call DISABLE_INTS.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch only moves the code. It doesn't make any changes, and the
code is still only compiled for powerpc. Follow-on patches will generalize
the code for other architectures.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
There is only one user, and it is trivial to open-code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
perf on POWER stopped working after commit e050e3f0a7 (perf: Fix
broken interrupt rate throttling). That patch exposed a bug in
the POWER perf_events code.
Since the PMCs count upwards and take an exception when the top bit
is set, we want to write 0x80000000 - left in power_pmu_start. We were
instead programming in left which effectively disables the counter
until we eventually hit 0x80000000. This could take seconds or longer.
With the patch applied I get the expected number of samples:
SAMPLE events: 9948
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>
Program Check exceptions are the result of WARNs, BUGs, some
type of breakpoints, kprobe, and other illegal instructions.
We want interrupts (and thus preemption) to remain disabled
while doing the initial stage of testing the reason and
branching off to a debugger or kprobe, so we are still on
the original CPU which makes debugging easier in various cases.
This is how the code was intended, hence the local_irq_enable()
right in the middle of program_check_exception().
However, the assembly exception prologue for that exception was
incorrectly marked as enabling interrupts, which defeats that
(and records a redundant enable with lockdep).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A kernel oops/panic prints an instruction dump showing several
instructions before and after the instruction which caused the
oops/panic.
The code intended that the faulting instruction be enclosed in angle
brackets, however a bug caused the faulting instruction to be
interpreted by printk() as the message log level.
To fix this, the KERN_CONT log level is added before the actual text of
the printed message.
=== Before the patch ===
[ 1081.587266] Instruction dump:
[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
[ 1081.602500] 4e800020 3803ffd0 2b800009
<4>[ 1081.587266] Instruction dump:
<4>[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
<98090000>[ 1081.602500] 4e800020 3803ffd0 2b800009
=== After the patch ===
[ 51.385216] Instruction dump:
[ 51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[ 51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009
<4>[ 51.385216] Instruction dump:
<4>[ 51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[ 51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch drops the powerpc-specific irq_map table and replaces it with
directly using the irq_alloc_desc()/irq_free_desc() interfaces for allocating
and freeing irq_desc structures.
This patch is a preparation step for generalizing the powerpc-specific virq
infrastructure to become irq_domains.
As part of this change, the irq_big_lock is changed to a mutex from a raw
spinlock. There is no longer any need to use a spin lock since the irq_desc
allocation code is now responsible for the critical section of finding
an unused range of irq numbers.
The radix lookup table is also changed to store the irq_data pointer instead
of the irq_map entry since the irq_map is removed. This should end up being
functionally equivalent since only allocated irq_descs are ever added to the
radix tree.
v5: - Really don't ever allocate virq 0. The previous version could still
do it if hint == 0
- Respect irq_virq_count setting for NOMAP. Some NOMAP domains cannot
use virq values above irq_virq_count.
- Use numa_node_id() when allocating irq_descs. Ideally the API should
obtain that value from the caller, but that touches a lot of call sites
so will be deferred to a follow-on patch.
- Fix irq_find_mapping() to include irq numbers lower than
NUM_ISA_INTERRUPTS. With the switch to irq_alloc_desc*(), the lowest
possible allocated irq is now returned by arch_probe_nr_irqs().
v4: - Fix incorrect access to irq_data structure in debugfs code
- Don't ever allocate virq 0
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
This patch drops the powerpc-specific irq_host structures and uses the common
irq_domain strucutres defined in linux/irqdomain.h. It also fixes all
the users to use the new structure names.
Renaming irq_host to irq_domain has been discussed for a long time, and this
patch is a step in the process of generalizing the powerpc virq code to be
usable by all architecture.
An astute reader will notice that this patch actually removes the irq_host
structure instead of renaming it. This is because the irq_domain structure
already exists in include/linux/irqdomain.h and has the needed data members.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
We use __get_cpu_var() which triggers a false positive warning
in smp_processor_id() thinking interrupts are enabled (at this
point, they are soft-enabled but hard-disabled).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When userspace needs to find a specific device, it currently isn't easy to
resolve a /sys/devices/ path from a specific device tree node. Nor is it
easy to obtain the compatible list for devices.
This patch generalizes the code that inserts OF_* values into the uevent
device attribute so that any device that is attached to an OF node will
have that information exported to userspace. Without this patch only
platform devices and some powerpc-specific busses have access to this
data.
The original function also creates a MODALIAS property for the compatible
list, but that code has not been generalized into the common case because
it has the potential to break module loading on a lot of bus types. Bus
types are still responsible for their own MODALIAS properties.
Boot tested on ARM and compile tested on PowerPC and SPARC.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Frederic Lambert <frdrc66@gmail.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Mark Brown <broonie@sirena.org.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 9deaa53ac7 broke build
on platforms that use legacy_serial.c without also having
CONFIG_SERIAL_8250_FSL enabled due to an unconditional code
to a routine in that module.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I could not find cpus_in_crash anywhere in the sourcetree, except for
arch/powerpc/kernel/crash.c. Moving the definition into the CONFIG_SMP
fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit: (29 commits)
audit: no leading space in audit_log_d_path prefix
audit: treat s_id as an untrusted string
audit: fix signedness bug in audit_log_execve_info()
audit: comparison on interprocess fields
audit: implement all object interfield comparisons
audit: allow interfield comparison between gid and ogid
audit: complex interfield comparison helper
audit: allow interfield comparison in audit rules
Kernel: Audit Support For The ARM Platform
audit: do not call audit_getname on error
audit: only allow tasks to set their loginuid if it is -1
audit: remove task argument to audit_set_loginuid
audit: allow audit matching on inode gid
audit: allow matching on obj_uid
audit: remove audit_finish_fork as it can't be called
audit: reject entry,always rules
audit: inline audit_free to simplify the look of generic code
audit: drop audit_set_macxattr as it doesn't do anything
audit: inline checks for not needing to collect aux records
audit: drop some potentially inadvisable likely notations
...
Use evil merge to fix up grammar mistakes in Kconfig file.
Bad speling and horrible grammar (and copious swearing) is to be
expected, but let's keep it to commit messages and comments, rather than
expose it to users in config help texts or printouts.
Every arch calls:
if (unlikely(current->audit_context))
audit_syscall_entry()
which requires knowledge about audit (the existance of audit_context) in
the arch code. Just do it all in static inline in audit.h so that arch's
can remain blissfully ignorant.
Signed-off-by: Eric Paris <eparis@redhat.com>
The audit system previously expected arches calling to audit_syscall_exit to
supply as arguments if the syscall was a success and what the return code was.
Audit also provides a helper AUDITSC_RESULT which was supposed to simplify things
by converting from negative retcodes to an audit internal magic value stating
success or failure. This helper was wrong and could indicate that a valid
pointer returned to userspace was a failed syscall. The fix is to fix the
layering foolishness. We now pass audit_syscall_exit a struct pt_reg and it
in turns calls back into arch code to collect the return value and to
determine if the syscall was a success or failure. We also define a generic
is_syscall_success() macro which determines success/failure based on if the
value is < -MAX_ERRNO. This works for arches like x86 which do not use a
separate mechanism to indicate syscall failure.
We make both the is_syscall_success() and regs_return_value() static inlines
instead of macros. The reason is because the audit function must take a void*
for the regs. (uml calls theirs struct uml_pt_regs instead of just struct
pt_regs so audit_syscall_exit can't take a struct pt_regs). Since the audit
function takes a void* we need to use static inlines to cast it back to the
arch correct structure to dereference it.
The other major change is that on some arches, like ia64, MIPS and ppc, we
change regs_return_value() to give us the negative value on syscall failure.
THE only other user of this macro, kretprobe_example.c, won't notice and it
makes the value signed consistently for the audit functions across all archs.
In arch/sh/kernel/ptrace_64.c I see that we were using regs[9] in the old
audit code as the return value. But the ptrace_64.h code defined the macro
regs_return_value() as regs[3]. I have no idea which one is correct, but this
patch now uses the regs_return_value() function, so it now uses regs[3].
For powerpc we previously used regs->result but now use the
regs_return_value() function which uses regs->gprs[3]. regs->gprs[3] is
always positive so the regs_return_value(), much like ia64 makes it negative
before calling the audit code when appropriate.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com> [for x86 portion]
Acked-by: Tony Luck <tony.luck@intel.com> [for ia64]
Acked-by: Richard Weinberger <richard@nod.at> [for uml]
Acked-by: David S. Miller <davem@davemloft.net> [for sparc]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [for mips]
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> [for ppc]
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPBZXBAAoJECgfDbjSjVRpuuYIAIMD0wE96MuTOSBJX4VG8VAP
UyjL9dsfMRy8CKioQo5/fxpTY07YBCWmNauSSX7pzgcoUKBfYIGn4Z1qwGYsWK9M
CzLs6PXLTugw0FtKobHZl/klRTWEBS6YOUjp9x568rplwF+Ppk7b993uj7eS/g+e
T0mUKzqg4/UavbHd9+W5KgC4drQ5hgtu2WZHoUxBK4umnd3C2G+U82Sthg50o/XU
SC8IGm39K8I36HoIWgXj3Y7nkOP3mQELohOT4ZPiVSmLvGS4i47+ix75anO+8ZvZ
jxHr8RC85IK1Nd89NZhbKOyvx0QQiwoKUZaTwcWXJNSOADzZnM6icdIsodc+Elo=
=ccQZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
lib: use generic pci_iomap on all architectures
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
alpha: drop pci_iomap/pci_iounmap from pci-noop.c
mn10300: switch to GENERIC_PCI_IOMAP
mn10300: add missing __iomap markers
frv: switch to GENERIC_PCI_IOMAP
tile: switch to GENERIC_PCI_IOMAP
tile: don't panic on iomap
sparc: switch to GENERIC_PCI_IOMAP
sh: switch to GENERIC_PCI_IOMAP
powerpc: switch to GENERIC_PCI_IOMAP
parisc: switch to GENERIC_PCI_IOMAP
mips: switch to GENERIC_PCI_IOMAP
microblaze: switch to GENERIC_PCI_IOMAP
arm: switch to GENERIC_PCI_IOMAP
alpha: switch to GENERIC_PCI_IOMAP
lib: add GENERIC_PCI_IOMAP
lib: move GENERIC_IOMAP to lib/Kconfig
Fix up trivial conflicts due to changes nearby in arch/{m68k,score}/Kconfig
Tracepoints should not be called inside an rcu_idle_enter/rcu_idle_exit
region. Since pSeries calls H_CEDE in the idle loop, we were violating
this rule.
commit a7b152d534 (powerpc: Tell RCU about idle after hcall tracing)
tried to work around it by delaying the rcu_idle_enter until after we
called the hcall tracepoint, but there are a number of issues with it.
The hcall tracepoint trampoline code is called conditionally when the
tracepoint is enabled. If the tracepoint is not enabled we never call
rcu_idle_enter. The idle_uses_rcu check was also done at compile time
which breaks multiplatform builds.
The simple fix is to avoid tracing H_CEDE and rely on other tracepoints
and the hypervisor dispatch trace log to work out if we called H_CEDE.
This fixes a hang during boot on pSeries.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: imx: move del_timer_sync() to avoid potential deadlock
imx: add polled io uart methods
imx: Add save/restore functions for UART control regs
serial/imx: let probing fail for the dt case without a valid alias
serial/imx: propagate error from of_alias_get_id instead of using -ENODEV
tty: serial: imx: Allow UART to be a source for wakeup
serial: driver for m32 arch should not have DEC alpha errata
serial/documentation: fix documented name of DCD cpp symbol
atmel_serial: fix spinlock lockup in RS485 code
tty: Fix memory leak in virtual console when enable unicode translation
serial: use DIV_ROUND_CLOSEST instead of open coding it
serial: add support for 400 and 800 v3 series Titan cards
serial: bfin-uart: Remove ASYNC_CTS_FLOW flag for hardware automatic CTS.
serial: bfin-uart: Enable hardware automatic CTS only when CTS pin is available.
serial: make FSL errata depend on 8250_CONSOLE, not just 8250
serial: add irq handler for Freescale 16550 errata.
serial: manually inline serial8250_handle_port
serial: make 8250 timeout use the specified IRQ handler
serial: export the key functions for an 8250 IRQ handler
serial: clean up parameter passing for 8250 Rx IRQ handling
...
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (185 commits)
powerpc: fix compile error with 85xx/p1010rdb.c
powerpc: fix compile error with 85xx/p1023_rds.c
powerpc/fsl: add MSI support for the Freescale hypervisor
arch/powerpc/sysdev/fsl_rmu.c: introduce missing kfree
powerpc/fsl: Add support for Integrated Flash Controller
powerpc/fsl: update compatiable on fsl 16550 uart nodes
powerpc/85xx: fix PCI and localbus properties in p1022ds.dts
powerpc/85xx: re-enable ePAPR byte channel driver in corenet32_smp_defconfig
powerpc/fsl: Update defconfigs to enable some standard FSL HW features
powerpc: Add TBI PHY node to first MDIO bus
sbc834x: put full compat string in board match check
powerpc/fsl-pci: Allow 64-bit PCIe devices to DMA to any memory address
powerpc: Fix unpaired probe_hcall_entry and probe_hcall_exit
offb: Fix setting of the pseudo-palette for >8bpp
offb: Add palette hack for qemu "standard vga" framebuffer
offb: Fix bug in calculating requested vram size
powerpc/boot: Change the WARN to INFO for boot wrapper overlap message
powerpc/44x: Fix build error on currituck platform
powerpc/boot: Change the load address for the wrapper to fit the kernel
powerpc/44x: Enable CRASH_DUMP for 440x
...
Fix up a trivial conflict in arch/powerpc/include/asm/cputime.h due to
the additional sparse-checking code for cputime_t.
Convert from pci_create_bus() to pci_create_root_bus(). This way the root
bus resources are correct immediately. This patch doesn't fix a problem
because powerpc fixed the resources before scanning the bus, but it makes
powerpc more consistent with other architectures.
v2: fix build error with resource pointer passing
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change. This is so we can use pcibios_phb_map_io_space()
before we have a struct pci_bus.
v2: fix map io phb typo
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch converts PowerPC's architecture-specific
'pcibios_set_master()' routine to a non-inlined function. This will
allow follow on patches to create a generic 'pcibios_set_master()'
function using the '__weak' attribute which can be used by all
architectures as a default which, if necessary, can then be over-
ridden by architecture-specific code.
Converting 'pci_bios_set_master()' to a non-inlined function will
allow PowerPC's 'pcibios_set_master()' implementation to remain
architecture-specific after the generic version is introduced and
thus, not change current behavior.
No functional change.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (64 commits)
cpu: Export cpu_up()
rcu: Apply ACCESS_ONCE() to rcu_boost() return value
Revert "rcu: Permit rt_mutex_unlock() with irqs disabled"
docs: Additional LWN links to RCU API
rcu: Augment rcu_batch_end tracing for idle and callback state
rcu: Add rcutorture tests for srcu_read_lock_raw()
rcu: Make rcutorture test for hotpluggability before offlining CPUs
driver-core/cpu: Expose hotpluggability to the rest of the kernel
rcu: Remove redundant rcu_cpu_stall_suppress declaration
rcu: Adaptive dyntick-idle preparation
rcu: Keep invoking callbacks if CPU otherwise idle
rcu: Irq nesting is always 0 on rcu_enter_idle_common
rcu: Don't check irq nesting from rcu idle entry/exit
rcu: Permit dyntick-idle with callbacks pending
rcu: Document same-context read-side constraints
rcu: Identify dyntick-idle CPUs on first force_quiescent_state() pass
rcu: Remove dynticks false positives and RCU failures
rcu: Reduce latency of rcu_prepare_for_idle()
rcu: Eliminate RCU_FAST_NO_HZ grace-period hang
rcu: Avoid needlessly IPIing CPUs at GP end
...
This moves the 'memory sysdev_class' over to a regular 'memory' subsystem
and converts the devices to regular devices. The sysdev drivers are
implemented as subsystem interfaces now.
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the 'cpu sysdev_class' over to a regular 'cpu' subsystem
and converts the devices to regular devices. The sysdev drivers are
implemented as subsystem interfaces now.
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Userspace relies on events and generic sysfs subsystem infrastructure
from sysdev devices, which are made available with this conversion.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Len Brown <lenb@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the PM core is now going to execute driver callbacks directly
if the corresponding subsystem callbacks are not present,
forward-only subsystem callbacks (i.e. such that only execute the
corresponding driver callbacks) are not necessary any more. Thus
it is possible to remove generic_subsys_pm_ops, because the only
callback in there that is not forward-only, .runtime_idle, is not
really used by the only user of generic_subsys_pm_ops, which is
vio_bus_type.
However, the generic callback routines themselves cannot be removed
from generic_ops.c, because they are used individually by a number
of subsystems.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Put the logic to compute the event index into a per pmu method. This
is required because the x86 rules are weird and wonderful and don't
match the capabilities of the current scheme.
AFAIK only powerpc actually has a usable userspace read of the PMCs
but I'm not at all sure anybody actually used that.
ARM is restored to the default since it currently does not support
userspace access at all. And all software events are provided with a
method that reports their index as 0 (disabled).
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Arun Sharma <asharma@fb.com>
Link: http://lkml.kernel.org/n/tip-dfydxodki16lylkt3gl2j7cw@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The following patch adds relocatable kernel support - based on processing
of dynamic relocations - for PPC44x kernel.
We find the runtime address of _stext and relocate ourselves based
on the following calculation.
virtual_base = ALIGN(KERNELBASE,256M) +
MODULO(_stext.run,256M)
relocate() is called with the Effective Virtual Base Address (as
shown below)
| Phys. Addr| Virt. Addr |
Page (256M) |------------------------|
Boundary | | |
| | |
| | |
Kernel Load |___________|_ __ _ _ _ _|<- Effective
Addr(_stext)| | ^ |Virt. Base Addr
| | | |
| | | |
| |reloc_offset|
| | | |
| | | |
| |______v_____|<-(KERNELBASE)%256M
| | |
| | |
| | |
Page(256M) |-----------|------------|
Boundary | | |
The virt_phys_offset is updated accordingly, i.e,
virt_phys_offset = effective. kernel virt base - kernstart_addr
I have tested the patches on 440x platforms only. However this should
work fine for PPC_47x also, as we only depend on the runtime address
and the current TLB XLAT entry for the startup code, which is available
in r25. I don't have access to a 47x board yet. So, it would be great if
somebody could test this on 47x.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The following patch implements the dynamic relocation processing for
PPC32 kernel. relocate() accepts the target virtual address and relocates
the kernel image to the same.
Currently the following relocation types are handled :
R_PPC_RELATIVE
R_PPC_ADDR16_LO
R_PPC_ADDR16_HI
R_PPC_ADDR16_HA
The last 3 relocations in the above list depends on value of Symbol indexed
whose index is encoded in the Relocation entry. Hence we need the Symbol
Table for processing such relocations.
Note: The GNU ld for ppc32 produces buggy relocations for relocation types
that depend on symbols. The value of the symbols with STB_LOCAL scope
should be assumed to be zero. - Alan Modra
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alan Modra <amodra@au1.ibm.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
DYNAMIC_MEMSTART(old RELOCATABLE) was restricted only to PPC_47x variants
of 44x. This patch enables DYNAMIC_MEMSTART for 440x based chipsets.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The current implementation of CONFIG_RELOCATABLE in BookE is based
on mapping the page aligned kernel load address to KERNELBASE. This
approach however is not enough for platforms, where the TLB page size
is large (e.g, 256M on 44x). So we are renaming the RELOCATABLE used
currently in BookE to DYNAMIC_MEMSTART to reflect the actual method.
The CONFIG_RELOCATABLE for PPC32(BookE) based on processing of the
dynamic relocations will be introduced in the later in the patch series.
This change would allow the use of the old method of RELOCATABLE for
platforms which can afford to enforce the page alignment (platforms with
smaller TLB size).
Changes since v3:
* Introduced a new config, NONSTATIC_KERNEL, to denote a kernel which is
either a RELOCATABLE or DYNAMIC_MEMSTART(Suggested by: Josh Boyer)
Suggested-by: Scott Wood <scottwood@freescale.com>
Tested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
As the kernels and initrd's get bigger boot-loaders and possibly
kexec-tools will need to place the initrd outside the RMO. When this
happens we end up with no lowmem and the boot doesn't get very far.
Only use initrd_end as the limit for alloc_bottom if it's inside the
RMO.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit d57af9b (taskstats: use real microsecond granularity for CPU times)
renamed msecs_to_cputime to usecs_to_cputime, but failed to update all
numbers on the way. This causes nonsensical cpu idle/iowait values to be
displayed in /proc/stat (the only user of usecs_to_cputime so far).
This also renames __cputime_msec_factor to __cputime_usec_factor, adapting
its value and using it directly in cputime_to_usecs instead of doing two
multiplications.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.
Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The PowerPC pSeries platform (CONFIG_PPC_PSERIES=y) enables
hypervisor-call tracing for CONFIG_TRACEPOINTS=y kernels. One of the
hypervisor calls that is traced is the H_CEDE call in the idle loop
that tells the hypervisor that this OS instance no longer needs the
current CPU. However, tracing uses RCU, so this combination of kernel
configuration variables needs to avoid telling RCU about the current CPU's
idleness until after the H_CEDE-entry tracing completes on the one hand,
and must tell RCU that the the current CPU is no longer idle before the
H_CEDE-exit tracing starts.
In all other cases, it suffices to inform RCU of CPU idleness upon
idle-loop entry and exit.
This commit makes the required adjustments.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.
To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().
If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().
Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:
- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:
- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.
There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.
Split this function into:
- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.
- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).
To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().
This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Sending a break on the SOC UARTs found in some MPC83xx/85xx/86xx
chips seems to cause a short lived IRQ storm (/proc/interrupts
typically shows somewhere between 300 and 1500 events). Unfortunately
this renders SysRQ over the serial console completely inoperable.
The suggested workaround in the errata is to read the Rx register,
wait one character period, and then read the Rx register again.
We achieve this by tracking the old LSR value, and on the subsequent
interrupt event after a break, we don't read LSR, instead we just
read the RBR again and return immediately.
The "fsl,ns16550" is used in the compatible field of the serial
device to mark UARTs known to have this issue.
Thanks to Scott Wood for providing the errata data which led to
a much cleaner fix.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only function of memblock_analyze() is now allowing resize of
memblock region arrays. Rename it to memblock_allow_resize() and
update its users.
* The following users remain the same other than renaming.
arm/mm/init.c::arm_memblock_init()
microblaze/kernel/prom.c::early_init_devtree()
powerpc/kernel/prom.c::early_init_devtree()
openrisc/kernel/prom.c::early_init_devtree()
sh/mm/init.c::paging_init()
sparc/mm/init_64.c::paging_init()
unicore32/mm/init.c::uc32_memblock_init()
* In the following users, analyze was used to update total size which
is no longer necessary.
powerpc/kernel/machine_kexec.c::reserve_crashkernel()
powerpc/kernel/prom.c::early_init_devtree()
powerpc/mm/init_32.c::MMU_init()
powerpc/mm/tlb_nohash.c::__early_init_mmu()
powerpc/platforms/ps3/mm.c::ps3_mm_add_memory()
powerpc/platforms/embedded6xx/wii.c::wii_memory_fixups()
sh/kernel/machine_kexec.c::reserve_crashkernel()
* x86/kernel/e820.c::memblock_x86_fill() was directly setting
memblock_can_resize before populating memblock and calling analyze
afterwards. Call memblock_allow_resize() before start populating.
memblock_can_resize is now static inside memblock.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
* early_init_devtree(): Total memory size is aligned to PAGE_SIZE;
however, alignment isn't enforced if memory_limit is explicitly
specified. Simplify the logic and always apply PAGE_SIZE alignment.
* MMU_init(): memblock regions is truncated by directly modifying
memblock.memory.cnt. This is incomplete (reserved array is not
truncated) and unnecessarily low level hindering further memblock
improvments. Use memblock_enforce_memory_limit() instead.
* wii_memory_fixups(): Unnecessarily low level direct manipulation of
memblock regions. The same result can be achieved using properly
abstracted operations. Reimplement using memblock API.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
memblock_init() initializes arrays for regions and memblock itself;
however, all these can be done with struct initializers and
memblock_init() can be removed. This patch kills memblock_init() and
initializes memblock with struct initializer.
The only difference is that the first dummy entries don't have .nid
set to MAX_NUMNODES initially. This doesn't cause any behavior
difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
This fixes a problem where a CPU thread coming out of nap mode can
think it has valid values in the nonvolatile GPRs (r14 - r31) as saved
away in power7_idle, but in fact the values have been trashed because
the thread was used for KVM in the mean time. The result is that the
thread crashes because code that called power7_idle (e.g.,
pnv_smp_cpu_kill_self()) goes to use values in registers that have
been trashed.
The bit field in SRR1 that tells whether state was lost only reflects
the most recent nap, which may not have been the nap instruction in
power7_idle. So we need an extra PACA field to indicate that state
has been lost even if SRR1 indicates that the most recent nap didn't
lose state. We clear this field when saving the state in power7_idle,
we set it to a non-zero value when we use the thread for KVM, and we
test it in power7_wakeup_noloss.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At present, on the powernv platform, if you off-line a CPU that was
online, and then try to on-line it again, the kernel generates a
warning message "OPAL Error -1 starting CPU n". Furthermore, if the
CPU is a secondary thread that was used by KVM while it was off-line,
the CPU fails to come online.
The first problem is fixed by only calling OPAL to start the CPU the
first time it is on-lined, as indicated by the cpu_start field of its
PACA being zero. The second problem is fixed by restoring the
cpu_start field to 1 instead of 0 when using the CPU within KVM.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The minimum RMO size field in ibm,client-architecture is currently
ignored, but a future firmware version will rectify that. Since we
always get at least 128MB of RMO right now, asking for 64MB is
likely to result in boot failures.
We should bump it to at least 128MB, but considering all the boot
issues we have on 128MB RMO boxes and all new machines have virtual
RMO, we may as well set our minimum to 256MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lv1_get_version_info hcall takes 2, not 1 output
arguments. Adjust the lv1 hcall table and all calls.
Usage:
int lv1_get_version_info(u64 *version_number, u64 *vendor_id)
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We might enter the secondary CPU capture code twice, eg if we have to
unstick some CPUs with a system reset. In this case we don't want to
overwrite the state on CPUs that had made it into the capture code OK,
so use the cpus_state_saved cpumask for that and make it local to
crash_ipi_callback.
For controlling progress now use atomic_t cpus_in_crash to count how
many CPUs have made it into the kdump code, and time_to_dump to tell
everyone it's time to dump.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we enter the kdump code via system reset, wait a bit before
sending the IPI to capture all secondary CPUs. Without it we race
with the hypervisor that is issuing the system reset to each CPU.
If the IPI gets there first the system reset oops output then shows
the register state of the IPI handler which is not what we want.
I took the opportunity to add defines for all the various delays
we have. There's no need for cpu_relax when we are doing an mdelay,
so remove them too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Our die() code was based off a very old x86 version. Update it to
mirror the current x86 code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove some unnecessary defines and fix some spelling mistakes.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can handle recursion caused by system reset by reusing the crash
shutdown fault handler.
Since we don't have an OS triggerable NMI, if all CPUs don't make it
into kdump then we tell the user to issue a system reset. However if
we have a panic timeout set we cannot wait forever and must continue
the kdump.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a lot of complicated logic that handles possible recursion between
kdump and a system reset exception. We can solve this in a much simpler
way using the same setjmp/longjmp tricks xmon does.
As a first step, this patch removes the old system reset code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I've been seeing truncated output when people send system reset info
to me. We should see a backtrace for every CPU, but the panic() code
takes the box down before they all make it out to the console. The
panic code runs unlocked so we also see corrupted console output.
If we are going to panic, then delay 1 second before calling into the
panic code. Move oops_exit inside the die lock and put a newline
between oopses for clarity.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch implements a back-end cpuidle driver for pSeries
based on pseries_dedicated_idle_loop and pseries_shared_idle_loop
routines. The driver is built only if CONFIG_CPU_IDLE is set. This
cpuidle driver uses global registration of idle states and
not per-cpu.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch provides cpu_idle_wait() routine for the powerpc
platform which is required by the cpuidle subsystem. This
routine is required to change the idle handler on SMP systems.
The equivalent routine for x86 is in arch/x86/kernel/process.c
but the powerpc implementation is different.
cpuidle_disable variable is to enable/disable cpuidle
framework if power_save option is set during the boot
time.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It's only used inside the same file where it's defined. There's
also no point exporting it anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Open Firmware on OPAL machines seems to have issues if we close
stdin and/or we try to print things after calling "quiesce" so
we avoid doing both.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For 64-bit FSL_BOOKE implementations, gigantic pages need to be
reserved at boot time by the memblock code based on the command line.
This adds the call that handles the reservation, and fixes some code
comments.
It also removes the previous pr_err when reserve_hugetlb_gpages
is called on a system without hugetlb enabled - the way the code is
structured, the call is unconditional and the resulting error message
spurious and confusing.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The AppliedMicro APM8018X embedded processor targets embedded applications that
require low power and a small footprint. It features a PowerPC 405 processor
core built in a 65nm low-power CMOS process with a five-stage pipeline executing
up to one instruction per cycle. The family has 128-kbytes of on-chip memory,
a 128-bit local bus and on-chip DDR2 SDRAM controller with 16-bit interface.
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
powerpc copied pci_iomap from generic code, probably to avoid
pulling the rest of iomap.c in. Since that's in
a separate file now, we can reuse the common implementation.
The only difference is handling of nocache flag,
that turns out to be done correctly by the
generic code since arch/powerpc/include/asm/io.h
defines ioremap_nocache same as ioremap.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
On a 64bit book3s machine I have an oops from a system reset that
claims the book3e CE bit was set:
MSR: 8000000000021032 <ME,CE,IR,DR> CR: 24004082 XER: 00000010
On a book3s machine system reset sets IBM bit 46 and 47 depending on
the power saving mode. Separate the definitions by type and for
completeness add the rest of the bits in.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On Fri, Nov 11, 2011 at 10:17:55AM +0530, Ananth N Mavinakayanahalli wrote:
> >
> > At this rate we're going to end up with no bits left for CPU features
> > way too quickly... Especially for something we only care about once at
> > boot time.
> >
> > Wouldn't CPU_FTR_PPCAS_ARCH_V2 be a good enough test ?
>
> /me checks Cell manuals... yes, that test would be good enough. I will
> cook up a patch to use this.
Here it is...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds support for p7IOC (and possibly other IODA v1 IO Hubs)
using OPAL v2 interfaces.
We completely take over resource assignment and assign them using an
algorithm that hands out device BARs in a way that makes them fit in
individual segments of the M32 window of the bridge, which enables us
to assign individual PEs to devices and functions.
The current implementation gives out a PE per functions on PCIe, and a
PE for the entire bridge for PCIe to PCI-X bridges.
This can be adjusted / fine tuned later.
We also setup DMA resources (32-bit only for now) and MSIs (both 32-bit
and 64-bit MSI are supported).
The DMA allocation tries to divide the available 256M segments of the
32-bit DMA address space "fairly" among PEs. This is done using a
"weight" heuristic which assigns less value to things like OHCI USB
controllers than, for example SCSI RAID controllers. This algorithm
will probably want some fine tuning for specific devices or device
types.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When PCI_REASSIGN_ALL_RSRC is set, we used to clear all bus resources
at the beginning of survey and re-allocate them later.
This changes it so instead, during early fixup, we mark all resources
as IORESOURCE_UNSET and move them down to be 0-based.
Later, if bus resources are still unset at the beginning of the survey,
then we clear them.
This shouldn't impact the re-assignment case on 4xx, but will enable
us to have the platform do some custom resource assignment before the
survey, by clearing individual resources IORESOURCE_UNSET bit.
Also limits the clutter in the kernel log from fixup when re-assigning
since we don't care about the offset applied to the BAR values in this
case.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some platforms need to perform resource allocation using a custom algorithm
due to HW constraints, or may want to tweak things globally below a host
bridge. For example OPAL support for IODA will need to perform a
resource allocation pass that applies IODA specific segmentation
constraints to MMIO which cannot be done simply using the kernel generic
resource management code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
IPI handlers cannot be threaded. Remove the obsolete IRQF_DISABLED
flag (see commit e58aa3d2) while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The RTAS firmware flash update is conducted using an RTAS call that is
serialized by lock_rtas() which uses spin_lock. While the flash is in
progress, rtasd performs scan for any RTAS events that are generated by
the system. rtasd keeps scanning for the RTAS events generated on the
machine. This is performed via workqueue mechanism. The rtas_event_scan()
also uses an RTAS call to scan the events, eventually trying to acquire
the spin_lock before issuing the request.
The flash update takes a while to complete and during this time, any other
RTAS call has to wait. In this case, rtas_event_scan() waits for a long time
on the spin_lock resulting in a soft lockup.
Fix: Just before the flash update is performed, the queued rtas_event_scan()
work item is cancelled from the work queue so that there is no other RTAS
call issued while the flash is in progress. After the flash completes, the
system reboots and the rtas_event_scan() is rescheduled.
Signed-off-by: Suzuki Poulose <suzuki@in.ibm.com>
Signed-off-by: Ravi Nittala <ravi.nittala@in.ibm.com>
Reported-by: Divya Vikas <divya.vikas@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
ICSWX is also used by the A2 processor to access coprocessors,
although not all "chips" that contain A2s have coprocessors.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
decrementer_check_overflow is called from arch_local_irq_restore so
we want to make it as light weight as possible. As such, turn
decrementer_check_overflow into an inline function.
To avoid a circular mess of includes, separate out the two components
of struct decrementer_clock and keep the struct clock_event_device
part local to time.c.
The fast path improves from:
arch_local_irq_restore
0: mflr r0
4: std r0,16(r1)
8: stdu r1,-112(r1)
c: stb r3,578(r13)
10: cmpdi cr7,r3,0
14: beq- cr7,24 <.arch_local_irq_restore+0x24>
...
24: addi r1,r1,112
28: ld r0,16(r1)
2c: mtlr r0
30: blr
to:
arch_local_irq_restore
0: std r30,-16(r1)
4: ld r30,0(r2)
8: stb r3,578(r13)
c: cmpdi cr7,r3,0
10: beq- cr7,6c <.arch_local_irq_restore+0x6c>
...
6c: ld r30,-16(r1)
70: blr
Unfortunately we still setup a local TOC (due to -mminimal-toc). Yet
another sign we should be moving to -mcmodel=medium.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix some formatting issues and use the DECREMENTER_MAX
define instead of 0x7fffffff.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The clockevents code uses max_delta_ns to avoid calling a
clockevent with too large a value.
Remove the redundant version of this in the timer_interrupt
code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use clocksource_register_hz which calculates the shift/mult
factors for us. Also remove the shift = 22 assumption in
vsyscall_update - thanks to Paul Mackerras and John Stultz for
catching that.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can use clockevents_calc_mult_shift instead of doing all
the work ourselves.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When re-enabling interrupts we have code to handle edge sensitive
decrementers by resetting the decrementer to 1 whenever it is negative.
If interrupts were disabled long enough that the decrementer wrapped to
positive we do nothing. This means interrupts can be delayed for a long
time until it finally goes negative again.
While we hope interrupts are never be disabled long enough for the
decrementer to go positive, we have a very good test team that can
drive any kernel into the ground. The softlockup data we get back
from these fails could be seconds in the future, completely missing
the cause of the lockup.
We already keep track of the timebase of the next event so use that
to work out if we should trigger a decrementer exception.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Current pci/pcie init code will hide the pci/pcie host resource.
But did not judge it is host/RC or agent/EP. If configured as
agent/EP, we should avoid hiding its resource in the host side.
In PCI system, the Programing Interface can be used to judge the
host/agent status:
Programing Interface = 0: host
Programing Interface = 1: Agent
In PCIE system, both the Programing Interface and Header type can
be used to judge the RC/EP status.
Header Type = 0: EP
Header Type = 1: RC
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On PPC64, put_sigset_t converts a sigset_t to a compat_sigset_t
before copying it to userspace. There is a typo in the case that
we have 4 words to copy, meaning that we corrupt the compat_sigset_t.
It appears that _NSIG_WORDS can't be greater than 2 at the moment
so this code is probably always optimised away anyway.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the introduction of CONFIG_PPC_ADV_DEBUG_REGS user space debug is
broken on Book-E 64-bit parts that support delayed debug events. When
switch_booke_debug_regs() sets DBCR0 we'll start getting debug events as
MSR_DE is also set and we aren't able to handle debug events from kernel
space.
We can remove the hack that always enables MSR_DE and loads up DBCR0 and
just utilize switch_booke_debug_regs() to get user space debug working
again.
We still need to handle critical/debug exception stacks & proper
save/restore of state for those exception levles to support debug events
from kernel space like we have on 32-bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All of DebugException is already protected by CONFIG_PPC_ADV_DEBUG_REGS
there is no need to have another such ifdef inside the function.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We had an existing ifdef for 4xx & BOOKE processors that got changed to
CONFIG_PPC_ADV_DEBUG_REGS. The define has nothing to do with
CONFIG_PPC_ADV_DEBUG_REGS. The define really should be:
#if defined(CONFIG_4xx) || defined(CONFIG_BOOKE)
and not
#ifdef CONFIG_PPC_ADV_DEBUG_REGS
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
kdump fails because we try to execute an HV only instruction. Feature
fixups are being applied after we copy the exception vectors down to 0
so they miss out on any updates.
We have always had this issue but it only became critical in v3.0
when we added CFAR support (breaks POWER5) and v3.1 when we added
POWERNV (breaks everyone).
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> [v3.0+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I had to debug a strange situation where all manner of things were
failing. SMT threads, storage and network were all completely broken.
The root cause was we couldn't find enough memory to instantiate RTAS -
this was a network install so the initrd was huge.
Instead of limping along and failing in mysterious ways we should just
panic up front if RTAS exists and we can't allocate space for it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kexec is not supported on 47x. 47x is a variant of 44x with slightly
different MMU and SMP support. There was a typo in the config dependency
for kexec. This patch fixes the same.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Should do what other architectures do and wrap all that code into
the appropriate ifdef
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When running with HV KVM and CBE config options enabled, I get
build failures like the following:
arch/powerpc/kernel/head_64.o: In function `cbe_system_error_hv':
(.text+0x1228): undefined reference to `do_kvm_0x1202'
arch/powerpc/kernel/head_64.o: In function `cbe_maintenance_hv':
(.text+0x1628): undefined reference to `do_kvm_0x1602'
arch/powerpc/kernel/head_64.o: In function `cbe_thermal_hv':
(.text+0x1828): undefined reference to `do_kvm_0x1802'
This is because we jump to a KVM handler when HV is enabled, but we
only generate the handler with PR KVM mode.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
Fix typo in comments introduced by:
commit 6dece0eb69
Author: Scott Wood <scottwood@freescale.com>
Date: Mon Jul 25 11:29:33 2011 +0000
powerpc/32: Pass device tree address as u64 to machine_init
Signed-off-by: Matthew McClintock <msm@freescale.com>
cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
None of the files touched here are modules, and they are not
exporting any symbols either -- so there is no need to be including
the module.h. Builds of all the files remains successful.
Even kernel/module.c does not need to include it, since it includes
linux/moduleloader.h instead.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
All these files were including module.h just for the basic
EXPORT_SYMBOL infrastructure. We can shift them off to the
export.h header which is a way smaller footprint and thus
realize some compile time gains.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This file only needs export.h to get EXPORT_SYMBOL, but in doing
so, it uncovers an implicit use of linux/cache.h as follows:
CC arch/powerpc/kernel/firmware.o
arch/powerpc/kernel/firmware.c:20: error: expected '=', ',', ';', 'asm' or '__attribute__' before '__read_mostly'
arch/powerpc/kernel/firmware.c:21: error: expected '=', ',', ';', 'asm' or '__attribute__' before '__used'
make[2]: *** [arch/powerpc/kernel/firmware.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
They are getting it through device.h --> module.h path, but we want
to clean that up. This is a sample of what will happen if we don't:
pseries/iommu.c: In function 'tce_build_pSeriesLP':
pseries/iommu.c:136: error: implicit declaration of function 'show_stack'
pseries/eeh.c: In function 'eeh_token_to_phys':
pseries/eeh.c:359: error: 'init_mm' undeclared (first use in this function)
pseries/eeh_event.c: In function 'eeh_event_handler':
pseries/eeh_event.c:63: error: implicit declaration of function 'daemonize'
pseries/eeh_event.c:64: error: implicit declaration of function 'set_current_state'
pseries/eeh_event.c:64: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
pseries/eeh_event.c:64: error: (Each undeclared identifier is reported only once
pseries/eeh_event.c:64: error: for each function it appears in.)
pseries/eeh_event.c: In function 'eeh_thread_launcher':
pseries/eeh_event.c:109: error: 'CLONE_KERNEL' undeclared (first use in this function)
hotplug-cpu.c: In function 'pseries_mach_cpu_die':
hotplug-cpu.c:115: error: implicit declaration of function 'idle_task_exit'
kernel/swsusp_64.c: In function 'do_after_copyback':
kernel/swsusp_64.c:17: error: implicit declaration of function 'touch_softlockup_watchdog'
cell/spufs/context.c: In function 'alloc_spu_context':
cell/spufs/context.c:60: error: implicit declaration of function 'get_task_mm'
cell/spufs/context.c:60: warning: assignment makes pointer from integer without a cast
cell/spufs/context.c: In function 'spu_forget':
cell/spufs/context.c:127: error: implicit declaration of function 'mmput'
pasemi/dma_lib.c: In function 'pasemi_dma_stop_chan':
pasemi/dma_lib.c:332: error: implicit declaration of function 'cond_resched'
sysdev/fsl_lbc.c: In function 'fsl_lbc_ctrl_irq':
sysdev/fsl_lbc.c:247: error: 'TASK_NORMAL' undeclared (first use in this function)
Add in sched.h so these get the definitions they are looking for.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
They get it via module.h (via device.h) but we want to clean that up.
When we do, we'll get things like:
ibmebus.c:314: error: 'S_IWUSR' undeclared here (not in a function)
vio.c:972: error: 'S_IWUSR' undeclared here (not in a function)
so add in the stat header it is using explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fix failures in powerpc associated with the previously allowed
implicit module.h presence that now lead to things like this:
arch/powerpc/mm/mmu_context_hash32.c:76:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/powerpc/mm/tlb_hash32.c:48:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/powerpc/kernel/pci_32.c:51:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/powerpc/kernel/iomap.c:36:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/powerpc/platforms/44x/canyonlands.c:126:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/powerpc/kvm/44x.c:168:59: error: 'THIS_MODULE' undeclared (first use in this function)
[with several contibutions from Stephen Rothwell <sfr@canb.auug.org.au>]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It was coming in via device.h --> module.h etc. but we want to
clean that up. So explicitly include the header where init_mm
is being declared.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'kvm-updates/3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (75 commits)
KVM: SVM: Keep intercepting task switching with NPT enabled
KVM: s390: implement sigp external call
KVM: s390: fix register setting
KVM: s390: fix return value of kvm_arch_init_vm
KVM: s390: check cpu_id prior to using it
KVM: emulate lapic tsc deadline timer for guest
x86: TSC deadline definitions
KVM: Fix simultaneous NMIs
KVM: x86 emulator: convert push %sreg/pop %sreg to direct decode
KVM: x86 emulator: switch lds/les/lss/lfs/lgs to direct decode
KVM: x86 emulator: streamline decode of segment registers
KVM: x86 emulator: simplify OpMem64 decode
KVM: x86 emulator: switch src decode to decode_operand()
KVM: x86 emulator: qualify OpReg inhibit_byte_regs hack
KVM: x86 emulator: switch OpImmUByte decode to decode_imm()
KVM: x86 emulator: free up some flag bits near src, dst
KVM: x86 emulator: switch src2 to generic decode_operand()
KVM: x86 emulator: expand decode flags to 64 bits
KVM: x86 emulator: split dst decode to a generic decode_operand()
KVM: x86 emulator: move memop, memopp into emulation context
...
For those MMUs that have some form of bolt'd linear mapping (TLB)
required its rare that one ever sets mem= smaller than the size of that
mapping.
However, on Book-E 64 parts the initial linear mapping is quite large
(1G) so its quite reasonable that mem= is set smaller than that.
We need to parse the command line for mem= limit and constrain the
amount of memory we map initially by it if need be.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is wrongly using undefined CONFIG_E500MC.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If the L1 D-Cache is in write shadow mode the HW will auto-recover the
error. However we might still log the error and cause a machine check
(if L1CSR0[CPE] - Cache error checking enable). We should only treat
the non-write shadow case as non-recoverable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The firmware on old 970 blades supports some kind of takeover called
"TNK takeover" which will crash if we try to probe for OPAL takeover,
so don't do it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current L1 cache read event code 0x80082 only counts for thread 0. The
event code 0x280030 should be used to count events on thread 0 and 1. The
patch fixes the event code for the L1 cache read.
The current L1 cache write event code 0x80086 only counts for thread 0. The
event code 0x180032 should be used to count events on thread 0 and 1. The
patch fixes the event code for the L1 cache write.
FYI, the documentation lists three event codes for the L1 cache read event
and three event codes for the L1 cache write event. The event description
for the event codes is as follows:
L1 cache read requests 0x80082 LSU 0 only
L1 cache read requests 0x8008A LSU 1 only
L1 cache read requests 0x80030 LSU 1 or LSU 0, counter 2 only.
L1 cache store requests 0x80086 LSU 0 only
L1 cache store requests 0x8008E LSU 1 only
L1 cache store requests 0x80032 LSU 0 or LSU 1, counter 1 only.
There can only be one request from either LSU 0 or 1 active at a time.
Signed-off-by: Carl Love <cel@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
gcc (rightfully) complains that we are accessing beyond the
end of the fpr array (we do, to access the fpscr).
The only sane thing to do (whether anything in that code can be
called remotely sane is debatable) is to special case fpscr and
handle it as a separate statement.
I initially tried to do it it by making the array access conditional
to index < PT_FPSCR and using a 3rd else leg but for some reason gcc
was unable to understand it and still spewed the warning.
So I ended up with something a tad more intricated but it seems to
build on 32-bit and on 64-bit with and without VSX.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We don't want to configure PCI Express Max Payload Size or
Max Read Request Size on systems that set that flag. The
firmware will have done it for us, and under hypervisors such
as pHyp we don't even see the parent switches and bridges and
thus can make no assumption on what values are safe to use.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With a KVM guest operating in SMT4 mode (i.e. 4 hardware threads per
core), whenever a CPU goes idle, we have to pull all the other
hardware threads in the core out of the guest, because the H_CEDE
hcall is handled in the kernel. This is inefficient.
This adds code to book3s_hv_rmhandlers.S to handle the H_CEDE hcall
in real mode. When a guest vcpu does an H_CEDE hcall, we now only
exit to the kernel if all the other vcpus in the same core are also
idle. Otherwise we mark this vcpu as napping, save state that could
be lost in nap mode (mainly GPRs and FPRs), and execute the nap
instruction. When the thread wakes up, because of a decrementer or
external interrupt, we come back in at kvm_start_guest (from the
system reset interrupt vector), find the `napping' flag set in the
paca, and go to the resume path.
This has some other ramifications. First, when starting a core, we
now start all the threads, both those that are immediately runnable and
those that are idle. This is so that we don't have to pull all the
threads out of the guest when an idle thread gets a decrementer interrupt
and wants to start running. In fact the idle threads will all start
with the H_CEDE hcall returning; being idle they will just do another
H_CEDE immediately and go to nap mode.
This required some changes to kvmppc_run_core() and kvmppc_run_vcpu().
These functions have been restructured to make them simpler and clearer.
We introduce a level of indirection in the wait queue that gets woken
when external and decrementer interrupts get generated for a vcpu, so
that we can have the 4 vcpus in a vcore using the same wait queue.
We need this because the 4 vcpus are being handled by one thread.
Secondly, when we need to exit from the guest to the kernel, we now
have to generate an IPI for any napping threads, because an HDEC
interrupt doesn't wake up a napping thread.
Thirdly, we now need to be able to handle virtual external interrupts
and decrementer interrupts becoming pending while a thread is napping,
and deliver those interrupts to the guest when the thread wakes.
This is done in kvmppc_cede_reentry, just before fast_guest_return.
Finally, since we are not using the generic kvm_vcpu_block for book3s_hv,
and hence not calling kvm_arch_vcpu_runnable, we can remove the #ifdef
from kvm_arch_vcpu_runnable.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This simplifies the way that the book3s_pr makes the transition to
real mode when entering the guest. We now call kvmppc_entry_trampoline
(renamed from kvmppc_rmcall) in the base kernel using a normal function
call instead of doing an indirect call through a pointer in the vcpu.
If kvm is a module, the module loader takes care of generating a
trampoline as it does for other calls to functions outside the module.
kvmppc_entry_trampoline then disables interrupts and jumps to
kvmppc_handler_trampoline_enter in real mode using an rfi[d].
That then uses the link register as the address to return to
(potentially in module space) when the guest exits.
This also simplifies the way that we call the Linux interrupt handler
when we exit the guest due to an external, decrementer or performance
monitor interrupt. Instead of turning on the MMU, then deciding that
we need to call the Linux handler and turning the MMU back off again,
we now go straight to the handler at the point where we would turn the
MMU on. The handler will then return to the virtual-mode code
(potentially in the module).
Along the way, this moves the setting and clearing of the HID5 DCBZ32
bit into real-mode interrupts-off code, and also makes sure that
we clear the MSR[RI] bit before loading values into SRR0/1.
The net result is that we no longer need any code addresses to be
stored in vcpu->arch.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This makes arch/powerpc/kvm/book3s_rmhandlers.S and
arch/powerpc/kvm/book3s_hv_rmhandlers.S be assembled as
separate compilation units rather than having them #included in
arch/powerpc/kernel/exceptions-64s.S. We no longer have any
conditional branches between the exception prologs in
exceptions-64s.S and the KVM handlers, so there is no need to
keep their contents close together in the vmlinux image.
In their current location, they are using up part of the limited
space between the first-level interrupt handlers and the firmware
NMI data area at offset 0x7000, and with some kernel configurations
this area will overflow (e.g. allyesconfig), leading to an
"attempt to .org backwards" error when compiling exceptions-64s.S.
Moving them out requires that we add some #includes that the
book3s_{,hv_}rmhandlers.S code was previously getting implicitly
via exceptions-64s.S.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Some devices have a dma-window that starts at the address 0. This allows
DMA addresses to be mapped to this address and returned to drivers as a
valid DMA address. Some drivers may not behave well in this case, since
the address 0 is considered an error or not allocated.
The solution to avoid this kind of error from happening is reserve the
page addressed as 0 so it cannot be allocated for a DMA mapping.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
perf events, powerpc: Add POWER7 stalled-cycles-frontend/backend events
Extent the POWER7 PMU driver with definitions for generic front-end and back-end
stall events.
As explained in Ingo's original comment(8f62242246
), the exact definitions of the stall events are very much processor specific as
different things mean different in their respective instruction pipeline. These
two Power7 raw events are the closest approximation to the concept detailed in
Ingo's comment.
[PERF_COUNT_HW_STALLED_CYCLES_FRONTEND] = 0x100f8, /* GCT_NOSLOT_CYC */
It means cycles when the Global Completion Table has no slots from this thread
[PERF_COUNT_HW_STALLED_CYCLES_BACKEND] = 0x4000a, /* CMPLU_STALL */
It means no groups completed and GCT not empty for this thread
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL can handle various interrupt for us such as Machine Checks (it
performs all sorts of recovery tasks and passes back control to us with
informations about the error), Hardware Management Interrupts and Softpatch
interrupts.
This wires up the mechanisms and prints out specific informations returned
by HAL when a machine check occurs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a udbg and an hvc console backend for supporting a console
using the OPAL console interfaces.
On OPAL v1 we have hvc0 mapped to whatever console the system was
configured for (network or hvsi serial port) via the service
processor.
On OPAL v2 we have hvcN mapped to the Nth console provided by OPAL
which generally corresponds to:
hvc0 : network console (raw protocol)
hvc1 : serial port S1 (hvsi)
hvc2 : serial port S2 (hvsi)
Note: At this point, early debug console only works with OPAL v1
and shouldn't be enabled in a normal kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL v2 is instantiated in a way similar to RTAS using Open Firmware
client interface calls, and the resulting address and entry point are
put in the device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add definition of OPAL interfaces along with the wrappers to call
into OPAL runtime and the early device-tree parsing hook to locate
the OPAL runtime firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We stash it in boot_command_line which isn't in BSS and so won't
be overwritten. We then use that as a default cmd_line before
we walk the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On machines supporting the OPAL firmware version 1, the system
is initially booted under pHyp. We then use a special hypercall
to verify if OPAL is available and if it is, we then trigger
a "takeover" which disables pHyp and loads the OPAL runtime
firmware, giving control to the kernel in hypervisor mode.
This patch add the necessary code to detect that the OPAL takeover
capability is present when running under PowerVM (aka pHyp) and
perform said takeover to get hypervisor control of the processor.
To perform the takeover, we must first use RTAS (within Open
Firmware runtime environment) to start all processors & threads,
in order to give control to OPAL on all of them. We then call
the takeover hypercall on everybody, OPAL will re-enter the kernel
main entry point passing it a flat device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With OPAL, r8 and r9 will be used to pass the OPAL base and entry
for debugging purposes (those informations are also in the
device-tree). We don't want to clobber those registers that
early.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This new function is used to properly setup the PCI Express Max Payload Size
(and in some circumstances Max Read Request Size).
Some systems will not operate properly if these aren't set correctly and
the firmware doesn't always do it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds more generic support for doing CPU hotplug with a simple
idle loop and no actual reset of the processors. The generic
smp_generic_kick_cpu() does the hotplug bringup trick if the PACA
shows that the CPU has already been started at boot and we provide
an accessor for the CPU state.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While converting code to use for_each_node_by_type I noticed a
number of coding style issues.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use for_each_node_by_type instead of open coding it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a new udbg driver for the PS3 gelic Ehthernet device.
This driver shares only a few stucture and constant definitions with the
gelic Ethernet device driver, so is implemented as a stand-alone driver
with no dependencies on the gelic Ethernet device driver.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In SMP mode, the kernel would produce call trace when resumed
from hibernation. The reason is when the function destroy_context
is called to drop the resuming mm context, the mm->context.active
is 1 which is wrong and should be zero.
We pass the current->active_mm as previous mm context to function
switch_mmu_context to decrease the context.active by 1.
In UP mode, there is no effect.
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
u64 is used rather than phys_addr_t to keep things simple, as
this is called from assembly code.
Update callers to pass a 64-bit address in r3/r4. Other unused
register assignments that were once parameters to machine_init
are dropped.
For FSL BookE, look up the physical address of the device tree from the
effective address passed in r3 by the loader. This is required for
situations where memory does not start at zero (due to AMP or IOMMU-less
virtualization), and thus the IMA doesn't start at zero, and thus the
device tree effective address does not equal the physical address.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable hugepages on Freescale BookE processors. This allows the kernel to
use huge TLB entries to map pages, which can greatly reduce the number of
TLB misses and the amount of TLB thrashing experienced by applications with
large memory footprints. Care should be taken when using this on FSL
processors, as the number of large TLB entries supported by the core is low
(16-64) on current processors.
The supported set of hugepage sizes include 4m, 16m, 64m, 256m, and 1g.
Page sizes larger than the max zone size are called "gigantic" pages and
must be allocated on the command line (and cannot be deallocated).
This is currently only fully implemented for Freescale 32-bit BookE
processors, but there is some infrastructure in the code for
64-bit BooKE.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This iotype is only used by the legacy_serial code in powerpc, so the
code should live there, rather than be compiled in for every 8250
driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-serial@vger.kernel.org
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new get_required_mask hook name is longer than many of but not all
of the prior ops. Tidy the struct initializers to align the equal signs
using the local whitespace.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that the generic code has dma_map_ops set, instead of having a
messy ifdef & if block in the base dma_get_required_mask hook push
the computation into the dma ops.
If the ops fails to set the get_required_mask hook default to the
width of dma_addr_t.
This also corrects ibmbus ibmebus_dma_supported to require a 64
bit mask. I doubt anything is checking or setting the dma mask on
that bus.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The hook dma_get_required_mask is supposed to return the mask required
by the platform to operate efficently. The generic version of
dma_get_required_mask in driver/base/platform.c returns a mask based
only on max_pfn. However, this is likely too big for iommu systems
and could be too small for platforms that require a dma offset or have
a secondary window at a high offset.
Override the default, provide a hook in ppc_md used by pseries lpar and
cell, and provide the default answer based on memblock_end_of_DRAM(),
with hooks for get_dma_offset, and provide an implementation for iommu
that looks at the defined table size. Coverting from the end address
to the required bit mask is based on the generic implementation.
The need for this was discovered when the qla2xxx driver switched to
64 bit dma then reverted to 32 bit when dma_get_required_mask said
32 bits was sufficient.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ePAPR embedded hypervisor specification provides an API for "byte
channels", which are serial-like virtual devices for sending and receiving
streams of bytes. This driver provides Linux kernel support for byte
channels via three distinct interfaces:
1) An early-console (udbg) driver. This provides early console output
through a byte channel. The byte channel handle must be specified in a
Kconfig option.
2) A normal console driver. Output is sent to the byte channel designated
for stdout in the device tree. The console driver is for handling kernel
printk calls.
3) A tty driver, which is used to handle user-space input and output. The
byte channel used for the console is designated as the default tty.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds kexec support for PPC440 based chipsets. This work is based
on the KEXEC patches for FSL BookE.
The FSL BookE patch and the code flow could be found at the link below:
http://patchwork.ozlabs.org/patch/49359/
Steps:
1) Invalidate all the TLB entries except the one this code is run from
2) Create a tmp mapping for our code in the other address space and jump to it
3) Invalidate the entry we used
4) Create a 1:1 mapping for 0-2GiB in blocks of 256M
5) Jump to the new 1:1 mapping and invalidate the tmp mapping
I have tested this patches on Ebony, Sequoia boards and Virtex on QEMU.
You need kexec-tools commit e8b7939b1e or newer for ppc440x support,
available at:
git://git.kernel.org/pub/scm/utils/kernel/kexec/kexec-tools.git
Signed-off-by: Suzuki Poulose <suzuki@in.ibm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Brown paper bag day, previous commit wouldn't work very well with modules
enabled. Move the exports into the ifdef.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit fea80311a9
"iomap: make IOPORT/PCI mapping functions conditional"
Broke powerpc build without CONFIG_PCI as we would still define
pci_iomap(), which overlaps with the new empty inline in the headers.
Make our implementation conditional on CONFIG_PCI
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are seeing boot failures on some very large boxes even with
commit b5416ca9f8 (powerpc: Move kdump default base address to
64MB on 64bit).
This patch halves the RMO so both kernels get about the same
amount of RMO memory. On large machines this region will be
at least 256MB, so each kernel will get 128MB.
We cap it at 256MB (small SLB size) since some early allocations need
to be in the bolted SLB region. We could relax this on machines with
1TB SLBs in a future patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Panic observed on an older kernel when collecting call chains for
the context-switch software event:
[<b0180e00>]rb_erase+0x1b4/0x3e8
[<b00430f4>]__dequeue_entity+0x50/0xe8
[<b0043304>]set_next_entity+0x178/0x1bc
[<b0043440>]pick_next_task_fair+0xb0/0x118
[<b02ada80>]schedule+0x500/0x614
[<b02afaa8>]rwsem_down_failed_common+0xf0/0x264
[<b02afca0>]rwsem_down_read_failed+0x34/0x54
[<b02aed4c>]down_read+0x3c/0x54
[<b0023b58>]do_page_fault+0x114/0x5e8
[<b001e350>]handle_page_fault+0xc/0x80
[<b0022dec>]perf_callchain+0x224/0x31c
[<b009ba70>]perf_prepare_sample+0x240/0x2fc
[<b009d760>]__perf_event_overflow+0x280/0x398
[<b009d914>]perf_swevent_overflow+0x9c/0x10c
[<b009db54>]perf_swevent_ctx_event+0x1d0/0x230
[<b009dc38>]do_perf_sw_event+0x84/0xe4
[<b009dde8>]perf_sw_event_context_switch+0x150/0x1b4
[<b009de90>]perf_event_task_sched_out+0x44/0x2d4
[<b02ad840>]schedule+0x2c0/0x614
[<b0047dc0>]__cond_resched+0x34/0x90
[<b02adcc8>]_cond_resched+0x4c/0x68
[<b00bccf8>]move_page_tables+0xb0/0x418
[<b00d7ee0>]setup_arg_pages+0x184/0x2a0
[<b0110914>]load_elf_binary+0x394/0x1208
[<b00d6e28>]search_binary_handler+0xe0/0x2c4
[<b00d834c>]do_execve+0x1bc/0x268
[<b0015394>]sys_execve+0x84/0xc8
[<b001df10>]ret_from_syscall+0x0/0x3c
A page fault occurred walking the callchain while creating a perf
sample for the context-switch event. To handle the page fault the
mmap_sem is needed, but it is currently held by setup_arg_pages.
(setup_arg_pages calls shift_arg_pages with the mmap_sem held.
shift_arg_pages then calls move_page_tables which has a cond_resched
at the top of its for loop - hitting that cond_resched is what caused
the context switch.)
This is an extension of Anton's proposed patch:
https://lkml.org/lkml/2011/7/24/151
adding case for 32-bit ppc.
Tested on the system that first generated the panic and then again
with latest kernel using a PPC VM. I am not able to test the 64-bit
path - I do not have H/W for it and 64-bit PPC VMs (qemu on Intel)
is horribly slow.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a newline to the panic messages in make_room. Also fix a
comment that suggested our chunk size is 4Mb. It's 1MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have a box that fails in OF during boot with:
DEFAULT CATCH!, exception-handler=fff00400
at %SRR0: 49424d2c4c6f6768 %SRR1: 800000004000b002
ie "IBM,Logh". OF got corrupted with a device tree string.
Looking at make_room and alloc_up, we claim the first chunk (1 MB)
but we never claim any more. mem_end is always set to alloc_top
which is the top of our available address space, guaranteeing we will
never call alloc_up and claim more memory.
Also alloc_up wasn't setting alloc_bottom to the bottom of the
available address space.
This doesn't help the box to boot, but we at least fail with
an obvious error. We could relocate the device tree in a future
patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit af9eef3c7b caused cpu_setup to see
the_cpu_spec, rather than the source struct. However, on 32-bit, the
return value of identify_cpu was being used for feature fixups, and
identify_cpu was returning the source struct. So if cpu_setup patches
the feature bits, the update won't affect the fixups.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
It is not necessary to share the same notifier.h.
This patch already moves register_reboot_notifier() and
unregister_reboot_notifier() from kernel/notifier.c to kernel/sys.c.
[amwang@redhat.com: make allyesconfig succeed on ppc64]
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
This patch removes all the module loader hook implementations in the
architecture specific code where the functionality is the same as that
now provided by the recently added default hooks.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (123 commits)
perf: Remove the nmi parameter from the oprofile_perf backend
x86, perf: Make copy_from_user_nmi() a library function
perf: Remove perf_event_attr::type check
x86, perf: P4 PMU - Fix typos in comments and style cleanup
perf tools: Make test use the preset debugfs path
perf tools: Add automated tests for events parsing
perf tools: De-opt the parse_events function
perf script: Fix display of IP address for non-callchain path
perf tools: Fix endian conversion reading event attr from file header
perf tools: Add missing 'node' alias to the hw_cache[] array
perf probe: Support adding probes on offline kernel modules
perf probe: Add probed module in front of function
perf probe: Introduce debuginfo to encapsulate dwarf information
perf-probe: Move dwarf library routines to dwarf-aux.{c, h}
perf probe: Remove redundant dwarf functions
perf probe: Move strtailcmp to string.c
perf probe: Rename DIE_FIND_CB_FOUND to DIE_FIND_CB_END
tracing/kprobe: Update symbol reference when loading module
tracing/kprobes: Support module init function probing
kprobes: Return -ENOENT if probe point doesn't exist
...
* 'of-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
pci/of: Consolidate pci_bus_to_OF_node()
pci/of: Consolidate pci_device_to_OF_node()
x86/devicetree: Use generic PCI <-> OF matching
microblaze/pci: Move the remains of pci_32.c to pci-common.c
microblaze/pci: Remove powermac originated cruft
pci/of: Match PCI devices to OF nodes dynamically
We already did it for hard IRQs but it looks like we forgot
to do it for softirqs. Without this, we would lose flags
such as TIF_NEED_RESCHED set using current_thread_info()
by something running of a softirq.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kernel loadable module can use hard_smp_processor_id() if building with SMP
kernel. In order to make it work for UP kernels too, boot_cpuid_phys
symbol (which is what hard_smp_processor_id() macro resolves to
in non-SMP configuration) must be exported.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now we have the CFAR saved add it to the oops output.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
HFI creates interrupts each time a window is setup. This results in
a lot of messages in the kernel log buffer:
irq: irq 199007 on host null mapped to virtual irq 351
This box has over 3500 of them, causing more important kernel
messages to be overwritten. We can get at this information via
debugfs now so we may as well turn it into a pr_debug.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The existing code it pretty ugly. How about we clean it up even more
like this?
From: Anton Blanchard <anton@samba.org>
We check for timeout expiry in the outer loop, but we also need to
check it in the inner loop or we can lock up forever waiting for a
CPU to hit real mode.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes the following warning:
WARNING: arch/powerpc/kernel/built-in.o(.text+0x29768): Section mismatch in reference from the function .register_power_pmu() to the function .cpuinit.text:.power_pmu_notifier()
The function .register_power_pmu() references
the function __cpuinit .power_pmu_notifier().
This is often because .register_power_pmu lacks a __cpuinit
annotation or the annotation of .power_pmu_notifier is wrong.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
