Remove the dependency on PCI initialization for SWIOTLB initialization.
So that PCI can be initialized at proper time.
SWIOTLB is partly determined by PCI inbound/outbound map which is assigned
in PCI initialization. But swiotlb_init() should be done at the stage of
mem_init() which is much earlier than PCI initialization. So we reserve the
memory for SWIOTLB first and free it if not necessary.
All boards are converted to fit this change.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the 64 bit case separate out e5500 cpu_setup and cpu_restore functions.
The cpu_setup function (for the primary core) is passed the cpu_spec
pointer, which is not there in case of the cpu_restore function. Also, in
our case we will have to manipulate the CPU_FTR_EMB_HV flag on the primary
core.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Merge the 32 bit cpu setup code for e500mc/e5500 and define the
"cpu_restore" routine (for e5500/e6500) only for the 64 bit case. The
cpu_restore routine is used in the 64 bit case for setting up the secondary
cores.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the E.HV check and CPU_FTR_EMB_HV flag manipulation to the cpu setup
code. Create a separate routine for E.HV ivors setup.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support to disable and re-enable individual cores at runtime on
MPC85xx/QorIQ SMP machines. Currently support e500v1/e500v2 core.
MPC85xx machines use ePAPR spin-table in boot page for CPU kick-off. This
patch uses the boot page from bootloader to boot core at runtime. It
supports 32-bit and 36-bit physical address.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the case of cpu hotplug, the cpu_state should be set to CPU_UP_PREPARE
when kicking cpu. Otherwise, the cpu_state is always CPU_DEAD after
calling generic_set_cpu_dead(), which makes the delay in generic_cpu_die()
not happen.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently we mark the DABRX to interrupt on all matches
(hypervisor/kernel/user and then filter in software. We can be a lot
smarter now that we can set the DABRX dynamically.
This sets the DABRX based on the flags passed by the user.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rework set_dabr to take a DABRX value as well.
Both the pseries and PS3 hypervisors do some checks on the DABRX
values that are passed in the hcall. This patch stops bogus values
from being passed to hypervisor. Also, in the case where we are
clearing the breakpoint, where DABR and DABRX are zero, we modify the
DABRX value to make it valid so that the hcall won't fail.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The idea comes from Benjamin Herrenschmidt. The eeh cache helps
fetching the pci device according to the given I/O address. Since
the eeh cache is serving for eeh, it's reasonable for eeh cache
to trace eeh device except pci device.
The patch make eeh cache to trace eeh device. Also, the major
eeh entry function eeh_dn_check_failure has been renamed to
eeh_dev_check_failure since it will take eeh device as input
parameter.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, we have 3 phases for EEH initialization on pSeries platform.
All of them are done through builtin functions: platform initialization,
EEH device creation, and EEH subsystem enablement. All of them are done
no later than ppc_md.setup_arch. That means that the slab/slub isn't ready
yet, so we have to allocate memory chunks on basis of PAGE_SIZE for those
dynamically created EEH devices. That's pretty expensive.
In order to utilize slab/slub for memory allocation, we have to move the EEH
initialization functions around, but all of them should be called after slab
is ready.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It's possible for the cpu_possible_mask to change between the time we
initialise the pacas and the time we setup per_cpu areas.
Obviously impossible cpus shouldn't ever be running, but stranger things
have happened. So be paranoid and initialise data_offset with a poison
value in case we don't set it up later.
Based on a patch from Anton Blanchard.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change bp_info to info to be consistent with the rest of this file.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc kernel doesn't export the memory limit enforced by 'mem='
kernel parameter. This is required for building the ELF header in
kexec-tools to limit the vmcore to capture only the used memory. On
powerpc the kexec-tools depends on the device-tree for memory related
information, unlike /proc/iomem on the x86.
Without this information, the kexec-tools assumes the entire System
RAM and vmcore creates an unnecessarily larger dump.
This patch exports the memory limit, if present, via
chosen/linux,memory-limit
property, so that the vmcore can be limited to the memory limit.
The prom_init seems to export this value in the same node. But doesn't
really
appear there. Also the memory_limit gets adjusted with the processing of
crashkernel= parameter. This patch makes sure we get the actual limit.
The kexec-tools will use the value to limit the 'end' of the memory
regions.
Tested this patch on ppc64 and ppc32(ppc440) with a kexec-tools
patch by Mahesh.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Tested-by: Mahesh J. Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are some device-tree nodes, whose values are of type phys_addr_t.
The phys_addr_t is variable sized based on the CONFIG_PHSY_T_64BIT.
Change these to a fixed unsigned long long for consistency.
This patch does the change only for memory_limit.
The following is a list of such variables which need the change:
1) kernel_end, crashk_size - in arch/powerpc/kernel/machine_kexec.c
2) (struct resource *)crashk_res.start - We could export a local static
variable from machine_kexec.c.
Changing the above values might break the kexec-tools. So, I will
fix kexec-tools first to handle the different sized values and then change
the above.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When PCI probe flag PCI_REASSIGN_ALL_RSRC has been passed into PCI
core, it's hoped that all resources to be reassigned by PCI core.
As to particular P2P (PCI-to-PCI) bridge, the size of the corresponding
BAR (I/O, MMIO, prefetchable MMIO) is calculated by the resources
required by the PCI devices behind the P2P bridge. That means that
the information like start/end address retrieved from the hardware
registers of the P2P bridge is meainingless in the case. However,
we still count that in and the BARs might have been configured by
firmware with non-zero size. That leads to space waste.
The patch explicitly sets the size of P2P bridge BARs to zero in
case that resource reassignment is expected with PCI probe flag
PCI_REASSIGN_ALL_RSRC. In the result, it will save overall resource
required by the system without waste.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Critical exception on 64-bit booke uses user-visible SPRG3 as scratch.
Restore VDSO information in SPRG3 on exception prolog.
Use a common sprg3 field in PACA for all powerpc64 architectures.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have been observing hangs, both of KVM guest vcpu tasks and more
generally, where a process that is woken doesn't properly wake up and
continue to run, but instead sticks in TASK_WAKING state. This
happens because the update of rq->wake_list in ttwu_queue_remote()
is not ordered with the update of ipi_message in
smp_muxed_ipi_message_pass(), and the reading of rq->wake_list in
scheduler_ipi() is not ordered with the reading of ipi_message in
smp_ipi_demux(). Thus it is possible for the IPI receiver not to see
the updated rq->wake_list and therefore conclude that there is nothing
for it to do.
In order to make sure that anything done before smp_send_reschedule()
is ordered before anything done in the resulting call to scheduler_ipi(),
this adds barriers in smp_muxed_message_pass() and smp_ipi_demux().
The barrier in smp_muxed_message_pass() is a full barrier to ensure that
there is a full ordering between the smp_send_reschedule() caller and
scheduler_ipi(). In smp_ipi_demux(), we use xchg() rather than
xchg_local() because xchg() includes release and acquire barriers.
Using xchg() rather than xchg_local() makes sense given that
ipi_message is not just accessed locally.
This moves the barrier between setting the message and calling the
cause_ipi() function into the individual cause_ipi implementations.
Most of them -- those that used outb, out_8 or similar -- already had
a full barrier because out_8 etc. include a sync before the MMIO
store. This adds an explicit barrier in the two remaining cases.
These changes made no measurable difference to the speed of IPIs as
measured using a simple ping-pong latency test across two CPUs on
different cores of a POWER7 machine.
The analysis of the reason why processes were not waking up properly
is due to Milton Miller.
Cc: stable@vger.kernel.org # v3.0+
Reported-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During a context switch we always restore the per thread DSCR value.
If we aren't doing explicit DSCR management
(ie thread.dscr_inherit == 0) and the default DSCR changed while
the process has been sleeping we end up with the wrong value.
Check thread.dscr_inherit and select the default DSCR or per thread
DSCR as required.
This was found with the following test case, when running with
more threads than CPUs (ie forcing context switching):
http://ozlabs.org/~anton/junkcode/dscr_default_test.c
With the four patches applied I can run a combination of all
test cases successfully at the same time:
http://ozlabs.org/~anton/junkcode/dscr_default_test.chttp://ozlabs.org/~anton/junkcode/dscr_explicit_test.chttp://ozlabs.org/~anton/junkcode/dscr_inherit_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the default DSCR is non zero we set thread.dscr_inherit in
copy_thread() meaning the new thread and all its children will ignore
future updates to the default DSCR. This is not intended and is
a change in behaviour that a number of our users have hit.
We just need to inherit thread.dscr and thread.dscr_inherit from
the parent which ends up being much simpler.
This was found with the following test case:
http://ozlabs.org/~anton/junkcode/dscr_default_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we update the DSCR either via emulation of mtspr(DSCR) or via
a change to dscr_default in sysfs we don't update thread.dscr.
We will eventually update it at context switch time but there is
a period where thread.dscr is incorrect.
If we fork at this point we will copy the old value of thread.dscr
into the child. To avoid this, always keep thread.dscr in sync with
reality.
This issue was found with the following testcase:
http://ozlabs.org/~anton/junkcode/dscr_inherit_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Writing to dscr_default in sysfs doesn't actually change the DSCR -
we rely on a context switch on each CPU to do the work. There is no
guarantee we will get a context switch in a reasonable amount of time
so fire off an IPI to force an immediate change.
This issue was found with the following test case:
http://ozlabs.org/~anton/junkcode/dscr_explicit_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The CPU hotplug code for the powernv platform currently only puts
offline CPUs into nap mode if the powersave_nap variable is set.
However, HV-style KVM on this platform requires secondary CPU threads
to be offline and in nap mode. Since we know nap mode works just
fine on all POWER7 machines, and the only machines that support the
powernv platform are POWER7 machines, this changes the code to
always put offline CPUs into nap mode, regardless of powersave_nap.
Powersave_nap still controls whether or not CPUs go into nap mode
when idle, as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment the handler for hypervisor decrementer interrupts is
the same as for decrementer interrupts, i.e. timer_interrupt().
This is bogus; if we ever do get a hypervisor decrementer interrupt
it won't have anything to do with the next timer event. In fact
the only time we get hypervisor decrementer interrupts is when one
is left pending on exit from a KVM guest.
When we get a hypervisor decrementer interrupt we don't need to do
anything special to clear it, since they are edge-triggered on the
transition of HDEC from 0 to -1. Thus this adds an empty handler
function for them. We don't need to have them masked when interrupts
are soft-disabled, so we use STD_EXCEPTION_HV instead of
MASKABLE_EXCEPTION_HV.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Embedded.Hypervisor category defines GSPRG0..3 physical registers for guests.
Avoid SPRG4-7 usage as scratch in host exception handlers, otherwise guest
SPRG4-7 registers will be clobbered.
For bolted TLB miss exception handlers, which is the version currently
supported by KVM, use SPRN_SPRG_GEN_SCRATCH aka SPRG0 instead of
SPRN_SPRG_TLB_SCRATCH aka SPRG6. Keep using TLB PACA slots to fit in one
64-byte cache line.
For critical exception handlers use SPRG3 instead of SPRG7. Provide a routine
to store and restore user-visible SPRGs. This will be subsequently used
to restore VDSO information in SPRG3. Add EX_R13 to paca slots to free up
SPRG3 and change the critical exception epilog to use it.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Refactor exception prolog to get rid of mfspr srr1 duplicate. This was
introduced by KVM integration, with DO_KVM macro logic expecting srr1 value
earlier in r11.
Reserve r11 to hold srr1's value also required at the end of the prolog and
free up r10 to serve as spare in addition macros.
For syscalls case this change does not add any performance penalty. For irq
soft-disabled case the change adds a store/load of conditional register value
to/from a paca slot. Paca slots fit in one 64-byte cache line so these
additional operations have little impact on performance.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Hook DO_KVM macro into 64-bit booke for KVM integration. Extend interrupt
handlers' parameter list with interrupt vector numbers to accomodate the macro.
Only the bolted version of tlb miss handers is addressed now.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Guest Doorbell interrupts use guest save and restore registers. Add a new
Guest Doorbell exception type to accommodate GSRR0/1 SPRs usage in exception
prolog and fix the exception handler.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Machine check exception handler was using a wrong prolog. Hypervisors like
KVM which are called early from the exception handler rely on the interrupt
source.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is the port of uprobes to powerpc. Usage is similar to x86.
[root@xxxx ~]# ./bin/perf probe -x /lib64/libc.so.6 malloc
Added new event:
probe_libc:malloc (on 0xb4860)
You can now use it in all perf tools, such as:
perf record -e probe_libc:malloc -aR sleep 1
[root@xxxx ~]# ./bin/perf record -e probe_libc:malloc -aR sleep 20
[ perf record: Woken up 22 times to write data ]
[ perf record: Captured and wrote 5.843 MB perf.data (~255302 samples) ]
[root@xxxx ~]# ./bin/perf report --stdio
...
69.05% tar libc-2.12.so [.] malloc
28.57% rm libc-2.12.so [.] malloc
1.32% avahi-daemon libc-2.12.so [.] malloc
0.58% bash libc-2.12.so [.] malloc
0.28% sshd libc-2.12.so [.] malloc
0.08% irqbalance libc-2.12.so [.] malloc
0.05% bzip2 libc-2.12.so [.] malloc
0.04% sleep libc-2.12.so [.] malloc
0.03% multipathd libc-2.12.so [.] malloc
0.01% sendmail libc-2.12.so [.] malloc
0.01% automount libc-2.12.so [.] malloc
The trap_nr addition patch is a prereq.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add thread_struct.trap_nr and use it to store the last exception
the thread experienced. In this patch, we populate the field at
various places where we force_sig_info() to the process.
This is also used in uprobes to determine if the probed instruction
caused an exception.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have an old FIXME in reg.h which points out that we should standardise
on PVR_foo for our PVR #defines. Currently we use PVR_ on 32-bit and PV_
on 64-bit.
So do that rename and remove the FIXME.
Seeing as we're touching all but one usage of __is_processor(), rename it
to something less ugly and more indicative of what it does, which is
simply to check the PVR version.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It's empty now, apart from other includes.
Fixup a few files that were getting things via this header.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These days they are just __va() and __pa() respectively.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Directly comparing current->personality against PER_LINUX32 doesn't work
in cases when any of the personality flags stored in the top three bytes
are used.
Directly forcefully setting personality to PER_LINUX32 or PER_LINUX
discards any flags stored in the top three bytes
Use personality() macro to compare only PER_MASK bytes and make sure that
we are setting only the bits that should be set, instead of overwriting
the whole value.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Checking for device mask to cover the whole IOMMU table is too strict.
IOMMU allocators should handle mask constraint properly for each
allocation.
The patch enables to use old AirPort Extreme cards on PowerMacs with
more than 1GB of memory; without the patch the driver init fails with:
b43-pci-bridge 0001:01:01.0: Warning: IOMMU window too big for device mask
b43-pci-bridge 0001:01:01.0: mask: 0x3fffffff, table end: 0x80000000
b43-phy0 ERROR: The machine/kernel does not support the required 30-bit DMA mask
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For powerpc BooKE and e200, singlestep is handled on the critical/dbg
exception stack. This causes current_thread_info() to fail for kgdb
internal, so previously We work around this issue by copying
the thread_info from the kernel stack before calling kgdb_handle_exception,
and copying it back afterwards.
But actually we don't do this properly. We should backup current_thread_info
then restore that when exit.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to skip a breakpoint exception when it occurs after
a breakpoint has already been removed.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kgdb_single_step flag has the possibility to indefinitely
hang the system on an SMP system.
The x86 arch have the same problem, and that problem was fixed by
commit 8097551d9ab9b9e3630(kgdb,x86: do not set kgdb_single_step
on x86). This patch does the same behaviors as x86's patch.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently if you are doing a global perf recording with hardware
breakpoints (ie perf record -e mem:0xdeadbeef -a), you can oops with:
Faulting instruction address: 0xc000000000738890
cpu 0xc: Vector: 300 (Data Access) at [c0000003f76af8d0]
pc: c000000000738890: .hw_breakpoint_handler+0xa0/0x1e0
lr: c000000000738830: .hw_breakpoint_handler+0x40/0x1e0
sp: c0000003f76afb50
msr: 8000000000001032
dar: 6f0
dsisr: 42000000
current = 0xc0000003f765ac00
paca = 0xc00000000f262a00 softe: 0 irq_happened: 0x01
pid = 6810, comm = loop-read
enter ? for help
[c0000003f76afbe0] c00000000073cd04 .notifier_call_chain.isra.0+0x84/0xe0
[c0000003f76afc80] c00000000073cdbc .notify_die+0x3c/0x60
[c0000003f76afd20] c0000000000139f0 .do_dabr+0x40/0xf0
[c0000003f76afe30] c000000000005a9c handle_dabr_fault+0x14/0x48
--- Exception: 300 (Data Access) at 0000000010000480
SP (ff8679e0) is in userspace
This is because we don't check to see if the break point is associated
with task before we deference the task_struct pointer.
This changes the update to use current.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull DMA-mapping updates from Marek Szyprowski:
"Those patches are continuation of my earlier work.
They contains extensions to DMA-mapping framework to remove limitation
of the current ARM implementation (like limited total size of DMA
coherent/write combine buffers), improve performance of buffer sharing
between devices (attributes to skip cpu cache operations or creation
of additional kernel mapping for some specific use cases) as well as
some unification of the common code for dma_mmap_attrs() and
dma_mmap_coherent() functions. All extensions have been implemented
and tested for ARM architecture."
* 'for-linus-for-3.6-rc1' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: add support for DMA_ATTR_SKIP_CPU_SYNC attribute
common: DMA-mapping: add DMA_ATTR_SKIP_CPU_SYNC attribute
ARM: dma-mapping: add support for dma_get_sgtable()
common: dma-mapping: introduce dma_get_sgtable() function
ARM: dma-mapping: add support for DMA_ATTR_NO_KERNEL_MAPPING attribute
common: DMA-mapping: add DMA_ATTR_NO_KERNEL_MAPPING attribute
common: dma-mapping: add support for generic dma_mmap_* calls
ARM: dma-mapping: fix error path for memory allocation failure
ARM: dma-mapping: add more sanity checks in arm_dma_mmap()
ARM: dma-mapping: remove custom consistent dma region
mm: vmalloc: use const void * for caller argument
scatterlist: add sg_alloc_table_from_pages function
Commit 9adc5374 ('common: dma-mapping: introduce mmap method') added a
generic method for implementing mmap user call to dma_map_ops structure.
This patch converts ARM and PowerPC architectures (the only providers of
dma_mmap_coherent/dma_mmap_writecombine calls) to use this generic
dma_map_ops based call and adds a generic cross architecture
definition for dma_mmap_attrs, dma_mmap_coherent, dma_mmap_writecombine
functions.
The generic mmap virt_to_page-based fallback implementation is provided for
architectures which don't provide their own implementation for mmap method.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
As Colin Cross ported my x86 change to ARM, he also pointed out that
powerpc is also behind in this fix.
The commit 722b3c7469 "ftrace/graph: Trace function entry before
updating index" fixes an issue with function graph tracing for x86,
where if the called entry function decides not to trace interrupts, it
can fail the check if an interrupt comes in just after the
curr_ret_stack is updated.
The solution is to call the entry function first, then update the
curr_ret_stack if the entry function wants to be traced.
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reduce the severity of the warning given when firmware flash is
not supported. Not all platforms have it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 9778b696a0 incorrectly
changes the code setting the stack limit on entry to the
kernel to mark the thread_info at the bottom of the stack
out of bounds anymore. This fixes it.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Host bridge hotplug
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos Kong)
Dynamic resource management
- Track bus number allocation (struct resource tree per domain) (Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment (Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup() (Myron Stowe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=oo/A
-----END PGP SIGNATURE-----
Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug:
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug:
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos
Kong)
Dynamic resource management:
- Track bus number allocation (struct resource tree per domain)
(Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment
(Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management:
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization:
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex
Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous:
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup()
(Myron Stowe)"
* tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits)
PCI: hotplug: ensure a consistent return value in error case
PCI: fix undefined reference to 'pci_fixup_final_inited'
PCI: build resource code for M68K architecture
PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width()
PCI: reorder __pci_assign_resource() (no change)
PCI: fix truncation of resource size to 32 bits
PCI: acpiphp: merge acpiphp_debug and debug
PCI: acpiphp: remove unused res_lock
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
...
A small set of changes for devicetree:
- Couple of Documentation fixes
- Addition of new helper function of_node_full_name
- Improve of_parse_phandle_with_args return values
- Some NULL related sparse fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQDwsgAAoJEMhvYp4jgsXiuwUH/Ri6ZSnqHcz4Wa/X4FxvNc3I
3Xelo/Vt3WLYue3s/+OYiM5FK9+KH8T6x+U79Q4p7vePcfUh6GJII0AUbMeRghkS
m3FjNd5syzYNJlnDnqdngQYRDpaz8U/SyftjXyMPjJ1VWiyLx/EJQUkj1EEwDLe/
ZVabppnco3Y6OJpFuETONNvXx5mE7xq86isW5+aYmviMkWSMMwJPf8qofLJ78Dh5
OAhWuCPRDooz548+Wkabt90qHjF6FU43w5fU7zZW26NT39ptppcbZ2bAXcTYqIIq
sATp5YSitvwFqO2c1mA/drZ9nrgxDPCaw3qCDyiMdcbWgXqDirz2x7q1iauVHF4=
=5TZ/
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.6' of git://sources.calxeda.com/kernel/linux
Pull devicetree updates from Rob Herring:
"A small set of changes for devicetree:
- Couple of Documentation fixes
- Addition of new helper function of_node_full_name
- Improve of_parse_phandle_with_args return values
- Some NULL related sparse fixes"
Grant's busy packing.
* tag 'dt-for-3.6' of git://sources.calxeda.com/kernel/linux:
of: mtd: nuke useless const qualifier
devicetree: add helper inline for retrieving a node's full name
of: return -ENOENT when no property
usage-model.txt: fix typo machine_init->init_machine
of: Fix null pointer related warnings in base.c file
LED: Fix missing semicolon in OF documentation
of: fix a few typos in the binding documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pECD
-----END PGP SIGNATURE-----
Merge tag 'kvm-3.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Avi Kivity:
"Highlights include
- full big real mode emulation on pre-Westmere Intel hosts (can be
disabled with emulate_invalid_guest_state=0)
- relatively small ppc and s390 updates
- PCID/INVPCID support in guests
- EOI avoidance; 3.6 guests should perform better on 3.6 hosts on
interrupt intensive workloads)
- Lockless write faults during live migration
- EPT accessed/dirty bits support for new Intel processors"
Fix up conflicts in:
- Documentation/virtual/kvm/api.txt:
Stupid subchapter numbering, added next to each other.
- arch/powerpc/kvm/booke_interrupts.S:
PPC asm changes clashing with the KVM fixes
- arch/s390/include/asm/sigp.h, arch/s390/kvm/sigp.c:
Duplicated commits through the kvm tree and the s390 tree, with
subsequent edits in the KVM tree.
* tag 'kvm-3.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (93 commits)
KVM: fix race with level interrupts
x86, hyper: fix build with !CONFIG_KVM_GUEST
Revert "apic: fix kvm build on UP without IOAPIC"
KVM guest: switch to apic_set_eoi_write, apic_write
apic: add apic_set_eoi_write for PV use
KVM: VMX: Implement PCID/INVPCID for guests with EPT
KVM: Add x86_hyper_kvm to complete detect_hypervisor_platform check
KVM: PPC: Critical interrupt emulation support
KVM: PPC: e500mc: Fix tlbilx emulation for 64-bit guests
KVM: PPC64: booke: Set interrupt computation mode for 64-bit host
KVM: PPC: bookehv: Add ESR flag to Data Storage Interrupt
KVM: PPC: bookehv64: Add support for std/ld emulation.
booke: Added crit/mc exception handler for e500v2
booke/bookehv: Add host crit-watchdog exception support
KVM: MMU: document mmu-lock and fast page fault
KVM: MMU: fix kvm_mmu_pagetable_walk tracepoint
KVM: MMU: trace fast page fault
KVM: MMU: fast path of handling guest page fault
KVM: MMU: introduce SPTE_MMU_WRITEABLE bit
KVM: MMU: fold tlb flush judgement into mmu_spte_update
...
