Pull timer fix from Thomas Gleixner:
"One more fix from the timer departement:
- Handle division of negative nanosecond values proper on 32bit.
A recent cleanup wrecked the sign handling of the dividend and
dropped the check for negative divisors"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Fix ktime_divns to do signed division
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Pull block fixes from Jens Axboe:
"Three small fixes that have been picked up the last few weeks.
Specifically:
- Fix a memory corruption issue in NVMe with malignant user
constructed request. From Christoph.
- Kill (now) unused blk_queue_bio(), dm was changed to not need this
anymore. From Mike Snitzer.
- Always use blk_schedule_flush_plug() from the io_schedule() path
when flushing a plug, fixing a !TASK_RUNNING warning with md. From
Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
sched: always use blk_schedule_flush_plug in io_schedule_out
nvme: fix kernel memory corruption with short INQUIRY buffers
block: remove export for blk_queue_bio
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contain Netfilter fixes for your net tree, they are:
1) Fix a race in nfnetlink_log and nfnetlink_queue that can lead to a crash.
This problem is due to wrong order in the per-net registration and netlink
socket events. Patch from Francesco Ruggeri.
2) Make sure that counters that userspace pass us are higher than 0 in all the
x_tables frontends. Discovered via Trinity, patch from Dave Jones.
3) Revert a patch for br_netfilter to rely on the conntrack status bits. This
breaks stateless IPv6 NAT transformations. Patch from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking socket spinlock in tcp_get_info() can deadlock, as
inet_diag_dump_icsk() holds the &hashinfo->ehash_locks[i],
while packet processing can use the reverse locking order.
We could avoid this locking for TCP_LISTEN states, but lockdep would
certainly get confused as all TCP sockets share same lockdep classes.
[ 523.722504] ======================================================
[ 523.728706] [ INFO: possible circular locking dependency detected ]
[ 523.734990] 4.1.0-dbg-DEV #1676 Not tainted
[ 523.739202] -------------------------------------------------------
[ 523.745474] ss/18032 is trying to acquire lock:
[ 523.750002] (slock-AF_INET){+.-...}, at: [<ffffffff81669d44>] tcp_get_info+0x2c4/0x360
[ 523.758129]
[ 523.758129] but task is already holding lock:
[ 523.763968] (&(&hashinfo->ehash_locks[i])->rlock){+.-...}, at: [<ffffffff816bcb75>] inet_diag_dump_icsk+0x1d5/0x6c0
[ 523.774661]
[ 523.774661] which lock already depends on the new lock.
[ 523.774661]
[ 523.782850]
[ 523.782850] the existing dependency chain (in reverse order) is:
[ 523.790326]
-> #1 (&(&hashinfo->ehash_locks[i])->rlock){+.-...}:
[ 523.796599] [<ffffffff811126bb>] lock_acquire+0xbb/0x270
[ 523.802565] [<ffffffff816f5868>] _raw_spin_lock+0x38/0x50
[ 523.808628] [<ffffffff81665af8>] __inet_hash_nolisten+0x78/0x110
[ 523.815273] [<ffffffff816819db>] tcp_v4_syn_recv_sock+0x24b/0x350
[ 523.822067] [<ffffffff81684d41>] tcp_check_req+0x3c1/0x500
[ 523.828199] [<ffffffff81682d09>] tcp_v4_do_rcv+0x239/0x3d0
[ 523.834331] [<ffffffff816842fe>] tcp_v4_rcv+0xa8e/0xc10
[ 523.840202] [<ffffffff81658fa3>] ip_local_deliver_finish+0x133/0x3e0
[ 523.847214] [<ffffffff81659a9a>] ip_local_deliver+0xaa/0xc0
[ 523.853440] [<ffffffff816593b8>] ip_rcv_finish+0x168/0x5c0
[ 523.859624] [<ffffffff81659db7>] ip_rcv+0x307/0x420
Lets use u64_sync infrastructure instead. As a bonus, 64bit
arches get optimized, as these are nop for them.
Fixes: 0df48c26d8 ("tcp: add tcpi_bytes_acked to tcp_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull HID fixes from Jiri Kosina:
"Bugfixes for HID subsystem that should go in 4.1. Important
highlights:
- the patch that extended support for HID++ protocol for TK820
touchpad turns out to be causing regressions due to firmware
issues; patch reverting back to basic support from Benjamin
Tissoires
- Wacom driver can oops for devices that report non-touch data on
touch interfaces. Fix from Ping Cheng
- gpiolib is not mandatory for i2c-hid, so the driver shouldn't fail
if gpiolib is not enabled. Fix from Mika Westerberg"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: fix an Oops caused by wacom_wac_finger_count_touches
HID: usbhid: Add HID_QUIRK_NOGET for Aten DVI KVM switch
HID: hid-sensor-hub: Fix debug lock warning
Revert "HID: logitech-hidpp: support combo keyboard touchpad TK820"
HID: i2c-hid: Do not fail probing if gpiolib is not enabled
exception of a single locking fix in the core code. All driver fixes are
for code that was merged recently. The Samsung stuff is mostly fixes
around suspend/resume, the Qualcomm fixes are for invalid hardware
configuration data and the Silicon Labs patches are fixes following
their move away from platform_data to Device Tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yjsw
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"The first set of clk fixes for 4.1 are all driver bugs, with the
exception of a single locking fix in the core code.
All driver fixes are for code that was merged recently. The Samsung
stuff is mostly fixes around suspend/resume, the Qualcomm fixes are
for invalid hardware configuration data and the Silicon Labs patches
are fixes following their move away from platform_data to Device Tree"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: si5351: Do not pass struct clk in platform_data
clk: si5351: Mention clock-names in the binding documentation
clk: add missing lock when call clk_core_enable in clk_set_parent
clk: exynos5420: Restore GATE_BUS_TOP on suspend
clk: qcom: Fix MSM8916 gfx3d_clk_src configuration
clk: qcom: Fix MSM8916 venus divider value
clk: exynos5433: Fix wrong PMS value of exynos5433_pll_rates
clk: exynos5433: Fix wrong parent clock of sclk_apollo clock
clk: exynos5433: Fix CLK_PCLK_MONOTONIC_CNT clk register assignment
clk: exynos5433: Fix wrong offset of PCLK_MSCL_SECURE_SMMU_JPEG
clk: Use CONFIG_ARCH_EXYNOS instead of CONFIG_ARCH_EXYNOS5433
This reverts commit c055d5b03b.
There are two issues:
'dnat_took_place' made me think that this is related to
-j DNAT/MASQUERADE.
But thats only one part of the story. This is also relevant for SNAT
when we undo snat translation in reverse/reply direction.
Furthermore, I originally wanted to do this mainly to avoid
storing ipv6 addresses once we make DNAT/REDIRECT work
for ipv6 on bridges.
However, I forgot about SNPT/DNPT which is stateless.
So we can't escape storing address for ipv6 anyway. Might as
well do it for ipv4 too.
Reported-and-tested-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A non-percpu VIRQ (e.g., VIRQ_CONSOLE) may be freed on a different
VCPU than it is bound to. This can result in a race between
handle_percpu_irq() and removing the action in __free_irq() because
handle_percpu_irq() does not take desc->lock. The interrupt handler
sees a NULL action and oopses.
Only use the percpu chip/handler for per-CPU VIRQs (like VIRQ_TIMER).
# cat /proc/interrupts | grep virq
40: 87246 0 xen-percpu-virq timer0
44: 0 0 xen-percpu-virq debug0
47: 0 20995 xen-percpu-virq timer1
51: 0 0 xen-percpu-virq debug1
69: 0 0 xen-dyn-virq xen-pcpu
74: 0 0 xen-dyn-virq mce
75: 29 0 xen-dyn-virq hvc_console
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: <stable@vger.kernel.org>
tcp_illinois and upcoming tcp_cdg require 64bit alignment of
icsk_ca_priv
x86 does not care, but other architectures might.
Fixes: 05cbc0db03 ("ipv4: Create probe timer for tcp PMTU as per RFC4821")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Fan Du <fan.du@intel.com>
Acked-by: Fan Du <fan.du@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's some TTY and serial driver fixes for reported issues. All of
these have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlVX4JMACgkQMUfUDdst+ymy/QCfSx/npI/WfRNlKBMHI20xwOaE
szQAoJKRxeF0d+2GCJ56OVbmqqjnG4IN
=FUtJ
-----END PGP SIGNATURE-----
Merge tag 'tty-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here's some TTY and serial driver fixes for reported issues.
All of these have been in linux-next successfully"
* tag 'tty-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
pty: Fix input race when closing
tty/n_gsm.c: fix a memory leak when gsmtty is removed
Revert "serial/amba-pl011: Leave the TX IRQ alone when the UART is not open"
serial: omap: Fix error handling in probe
earlycon: Revert log warnings
We currently have no limit on the number of elements in a hash table.
This is a problem because some users (tipc) set a ceiling on the
maximum table size and when that is reached the hash table may
degenerate. Others may encounter OOM when growing and if we allow
insertions when that happens the hash table perofrmance may also
suffer.
This patch adds a new paramater insecure_max_entries which becomes
the cap on the table. If unset it defaults to max_size * 2. If
it is also zero it means that there is no cap on the number of
elements in the table. However, the table will grow whenever the
utilisation hits 100% and if that growth fails, you will get ENOMEM
on insertion.
As allowing oversubscription is potentially dangerous, the name
contains the word insecure.
Note that the cap is not a hard limit. This is done for performance
reasons as enforcing a hard limit will result in use of atomic ops
that are heavier than the ones we currently use.
The reasoning is that we're only guarding against a gross over-
subscription of the table, rather than a small breach of the limit.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter fixes for your net tree, they are:
1) Fix a leak in IPVS, the sysctl table is not released accordingly when
destroying a netns, patch from Tommi Rantala.
2) Fix a build error when TPROXY and socket are built-in but IPv6 defrag is
compiled as module, from Florian Westphal.
3) Fix TCP tracket wrt. RFC5961 challenge ACK when in LAST_ACK state, patch
from Jesper Dangaard Brouer.
4) Fix a bogus WARN_ON() in nf_tables when deleting a set element that stores
a map, from Mirek Kratochvil.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler fixes from Ingo Molnar:
"Two fixes: a suspend/resume related regression fix, and an RT priority
boosting fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Fix regression in cpuset_cpu_inactive() for suspend
sched: Handle priority boosted tasks proper in setscheduler()
In compliance with RFC5961, the network stack send challenge ACK in
response to spurious SYN packets, since commit 0c228e833c ("tcp:
Restore RFC5961-compliant behavior for SYN packets").
This pose a problem for netfilter conntrack in state LAST_ACK, because
this challenge ACK is (falsely) seen as ACKing last FIN, causing a
false state transition (into TIME_WAIT).
The challenge ACK is hard to distinguish from real last ACK. Thus,
solution introduce a flag that tracks the potential for seeing a
challenge ACK, in case a SYN packet is let through and current state
is LAST_ACK.
When conntrack transition LAST_ACK to TIME_WAIT happens, this flag is
used for determining if we are expecting a challenge ACK.
Scapy based reproducer script avail here:
https://github.com/netoptimizer/network-testing/blob/master/scapy/tcp_hacks_3WHS_LAST_ACK.py
Fixes: 0c228e833c ("tcp: Restore RFC5961-compliant behavior for SYN packets")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull drm fixes from Dave Airlie:
"Radeon:
one oops fix, one bug fix, one pci id addition patch
i915:
one suspend/resume regression fix.
All seems quiet enough."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: don't do mst probing if MST isn't enabled.
drm/radeon: add new bonaire pci id
drm/radeon: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR handling
drm/i915: Avoid GPU hang when coming out of s3 or s4
radeon minor fixes, and pci id addition.
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: don't do mst probing if MST isn't enabled.
drm/radeon: add new bonaire pci id
drm/radeon: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR handling
RTNH_F_EXTERNAL today is printed as "offload" in iproute2 output.
This patch renames the flag to be consistent with what the user sees.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
{u,g}id_valid call {u,g}id_eq, which calls __k{u,g}id_val on both
arguments and compares. With !CONFIG_MULTIUSER, __k{u,g}id_val return a
constant 0, which makes {u,g}id_valid always return false. Change
{u,g}id_valid to compare their argument against -1 instead. That produces
identical results in the normal CONFIG_MULTIUSER=y case, but with
!CONFIG_MULTIUSER will make {u,g}id_valid constant-fold into "return
true;" rather than "return false;".
This fixes uses of devpts without CONFIG_MULTIUSER.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>,
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not all kmem allocations should be accounted to memcg. The following
patch gives an example when accounting of a certain type of allocations to
memcg can effectively result in a memory leak. This patch adds the
__GFP_NOACCOUNT flag which if passed to kmalloc and friends will force the
allocation to go through the root cgroup. It will be used by the next
patch.
Note, since in case of kmemleak enabled each kmalloc implies yet another
allocation from the kmemleak_object cache, we add __GFP_NOACCOUNT to
gfp_kmemleak_mask.
Alternatively, we could introduce a per kmem cache flag disabling
accounting for all allocations of a particular kind, but (a) we would not
be able to bypass accounting for kmalloc then and (b) a kmem cache with
this flag set could not be merged with a kmem cache without this flag,
which would increase the number of global caches and therefore
fragmentation even if the memory cgroup controller is not used.
Despite its generic name, currently __GFP_NOACCOUNT disables accounting
only for kmem allocations while user page allocations are always charged.
To catch abusing of this flag, a warning is issued on an attempt of
passing it to mem_cgroup_try_charge.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org> [4.0.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was noted that the 32bit implementation of ktime_divns()
was doing unsigned division and didn't properly handle
negative values.
And when a ktime helper was changed to utilize
ktime_divns, it caused a regression on some IR blasters.
See the following bugzilla for details:
https://bugzilla.redhat.com/show_bug.cgi?id=1200353
This patch fixes the problem in ktime_divns by checking
and preserving the sign bit, and then reapplying it if
appropriate after the division, it also changes the return
type to a s64 to make it more obvious this is expected.
Nicolas also pointed out that negative dividers would
cause infinite loops on 32bit systems, negative dividers
is unlikely for users of this function, but out of caution
this patch adds checks for negative dividers for both
32-bit (BUG_ON) and 64-bit(WARN_ON) versions to make sure
no such use cases creep in.
[ tglx: Hand an u64 to do_div() to avoid the compiler warning ]
Fixes: 166afb6451 'ktime: Sanitize ktime_to_us/ms conversion'
Reported-and-tested-by: Trevor Cordes <trevor@tecnopolis.ca>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1431118043-23452-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull networking fixes from David Miller:
1) Handle max TX power properly wrt VIFs and the MAC in iwlwifi, from
Avri Altman.
2) Use the correct FW API for scan completions in iwlwifi, from Avraham
Stern.
3) FW monitor in iwlwifi accidently uses unmapped memory, fix from Liad
Kaufman.
4) rhashtable conversion of mac80211 station table was buggy, the
virtual interface was not taken into account. Fix from Johannes
Berg.
5) Fix deadlock in rtlwifi by not using a zero timeout for
usb_control_msg(), from Larry Finger.
6) Update reordering state before calculating loss detection, from
Yuchung Cheng.
7) Fix off by one in bluetooth firmward parsing, from Dan Carpenter.
8) Fix extended frame handling in xiling_can driver, from Jeppe
Ledet-Pedersen.
9) Fix CODEL packet scheduler behavior in the presence of TSO packets,
from Eric Dumazet.
10) Fix NAPI budget testing in fm10k driver, from Alexander Duyck.
11) macvlan needs to propagate promisc settings down the the lower
device, from Vlad Yasevich.
12) igb driver can oops when changing number of rings, from Toshiaki
Makita.
13) Source specific default routes not handled properly in ipv6, from
Markus Stenberg.
14) Use after free in tc_ctl_tfilter(), from WANG Cong.
15) Use softirq spinlocking in netxen driver, from Tony Camuso.
16) Two ARM bpf JIT fixes from Nicolas Schichan.
17) Handle MSG_DONTWAIT properly in ring based AF_PACKET sends, from
Mathias Kretschmer.
18) Fix x86 bpf JIT implementation of FROM_{BE16,LE16,LE32}, from Alexei
Starovoitov.
19) ll_temac driver DMA maps TX packet header with incorrect length, fix
from Michal Simek.
20) We removed pm_qos bits from netdevice.h, but some indirect
references remained. Kill them. From David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
net: Remove remaining remnants of pm_qos from netdevice.h
e1000e: Add pm_qos header
net: phy: micrel: Fix regression in kszphy_probe
net: ll_temac: Fix DMA map size bug
x86: bpf_jit: fix FROM_BE16 and FROM_LE16/32 instructions
netns: return RTM_NEWNSID instead of RTM_GETNSID on a get
Update be2net maintainers' email addresses
net_sched: gred: use correct backlog value in WRED mode
pppoe: drop pppoe device in pppoe_unbind_sock_work
net: qca_spi: Fix possible race during probe
net: mdio-gpio: Allow for unspecified bus id
af_packet / TX_RING not fully non-blocking (w/ MSG_DONTWAIT).
bnx2x: limit fw delay in kdump to 5s after boot
ARM: net: delegate filter to kernel interpreter when imm_offset() return value can't fit into 12bits.
ARM: net fix emit_udiv() for BPF_ALU | BPF_DIV | BPF_K intruction.
mpls: Change reserved label names to be consistent with netbsd
usbnet: avoid integer overflow in start_xmit
netxen_nic: use spin_[un]lock_bh around tx_clean_lock (2)
net: xgene_enet: Set hardware dependency
net: amd-xgbe: Add hardware dependency
...
Commit e2c6544829 removed pm_qos from struct net_device but left the
comment and header file. Remove those.
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit ff36ab345 ("dm: remove request-based logic from
make_request_fn wrapper") DM no longer calls blk_queue_bio() directly,
so remove its export. Doing so required a forward declaration in
blk-core.c.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When CONFIG_DEBUG_LOCK_ALLOC is defined, mutex magic is compared and
warned for (l->magic != l), here l is the address of mutex pointer.
In hid-sensor-hub as part of hsdev creation, a per hsdev mutex is
initialized during MFD cell creation. This hsdev, which contains, mutex
is part of platform data for the a cell. But platform_data is copied
in platform_device_add_data() in platform.c. This copy will copy the
whole hsdev structure including mutex. But once copied the magic
will no longer match. So when client driver call
sensor_hub_input_attr_get_raw_value, this will trigger mutex warning.
So to avoid this allocate mutex dynamically. This will be same even
after copy.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull libata fixes from Tejun Heo:
"Rather big for fixes pull.
- SCC controllers never lived to see the light of the day. Both
libata and ide drivers removed.
- In some configurations, link power management policy changes
sometimes cause delayed spurious PHY events which can develop into
noticeable failures. This has been reported several times over the
years. Gabriele's patches suppress PHY events for a while after
LPM policy changes which should help most of these failures without
causing too much problem for hotplug use cases.
- A few controller specific fixes"
[ Hmm. I don't think removing SSC support is really a "fix", but hey, it
removes a lot of lines of code. Which I like. So ... good riddance ]
* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: avoton port-disable reset-quirk
ata: select DW_DMAC in case of SATA_DWC
libata: Blacklist queued TRIM on all Samsung 800-series
libata: Ignore spurious PHY event on LPM policy change
libata: Add helper to determine when PHY events should be ignored
ata: ahci_st: fixup layering violations / drvdata errors
Remove celleb-only SCC PATA drivers
A read() from a pty master may mistakenly indicate EOF (errno == -EIO)
after the pty slave has closed, even though input data remains to be read.
For example,
pty slave | input worker | pty master
| |
| | n_tty_read()
pty_write() | | input avail? no
add data | | sleep
schedule worker --->| | .
|---> flush_to_ldisc() | .
pty_close() | fill read buffer | .
wait for worker | wakeup reader --->| .
| read buffer full? |---> input avail ? yes
|<--- yes - exit worker | copy 4096 bytes to user
TTY_OTHER_CLOSED <---| |<--- kick worker
| |
**** New read() before worker starts ****
| | n_tty_read()
| | input avail? no
| | TTY_OTHER_CLOSED? yes
| | return -EIO
Several conditions are required to trigger this race:
1. the ldisc read buffer must become full so the input worker exits
2. the read() count parameter must be >= 4096 so the ldisc read buffer
is empty
3. the subsequent read() occurs before the kicked worker has processed
more input
However, the underlying cause of the race is that data is pipelined, while
tty state is not; ie., data already written by the pty slave end is not
yet visible to the pty master end, but state changes by the pty slave end
are visible to the pty master end immediately.
Pipeline the TTY_OTHER_CLOSED state through input worker to the reader.
1. Introduce TTY_OTHER_DONE which is set by the input worker when
TTY_OTHER_CLOSED is set and either the input buffers are flushed or
input processing has completed. Readers/polls are woken when
TTY_OTHER_DONE is set.
2. Reader/poll checks TTY_OTHER_DONE instead of TTY_OTHER_CLOSED.
3. A new input worker is started from pty_close() after setting
TTY_OTHER_CLOSED, which ensures the TTY_OTHER_DONE state will be
set if the last input worker is already finished (or just about to
exit).
Remove tty_flush_to_ldisc(); no in-tree callers.
Fixes: 52bce7f8d4 ("pty, n_tty: Simplify input processing on final close")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96311
BugLink: http://bugs.launchpad.net/bugs/1429756
Cc: <stable@vger.kernel.org> # 3.19+
Reported-by: Andy Whitcroft <apw@canonical.com>
Reported-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since these are now visible to userspace it is nice to be consistent
with BSD (sys/netmpls/mpls.h in netBSD).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull irq updates from Thomas Gleixner:
"Two patches from the irq departement:
- a simple fix to make dummy_irq_chip usable for wakeup scenarios
- removal of the gic arch_extn hackery. Now that all users are
converted we really want to get rid of the interface so people wont
come up with new use cases"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: gic: Drop support for gic_arch_extn
genirq: Set IRQCHIP_SKIP_SET_WAKE flag for dummy_irq_chip
Pull block fixes from Jens Axboe:
"A collection of fixes since the merge window;
- fix for a double elevator module release, from Chao Yu. Ancient bug.
- the splice() MORE flag fix from Christophe Leroy.
- a fix for NVMe, fixing a patch that went in in the merge window.
From Keith.
- two fixes for blk-mq CPU hotplug handling, from Ming Lei.
- bdi vs blockdev lifetime fix from Neil Brown, fixing and oops in md.
- two blk-mq fixes from Shaohua, fixing a race on queue stop and a
bad merge issue with FUA writes.
- division-by-zero fix for writeback from Tejun.
- a block bounce page accounting fix, making sure we inc/dec after
bouncing so that pre/post IO pages match up. From Wang YanQing"
* 'for-linus' of git://git.kernel.dk/linux-block:
splice: sendfile() at once fails for big files
blk-mq: don't lose requests if a stopped queue restarts
blk-mq: fix FUA request hang
block: destroy bdi before blockdev is unregistered.
block:bounce: fix call inc_|dec_zone_page_state on different pages confuse value of NR_BOUNCE
elevator: fix double release of elevator module
writeback: use |1 instead of +1 to protect against div by zero
blk-mq: fix CPU hotplug handling
blk-mq: fix race between timeout and CPU hotplug
NVMe: Fix VPD B0 max sectors translation
the only user of it didn't make the 4.1 merge window. But the helper
function should be fixed before 4.2 when the users start coming in.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVTBNUAAoJEEjnJuOKh9ld0VQIAJWPLivGbGJyjSqFd1NXLidS
ytcbM0dquYjvQ94EDxoA+uBm34hk1JbvcI+FgiOihEeyGh7wrhdibEVGT40TzE2I
XrfTVwPfN5/k2D5MeZzzRkeoTDufc33MgqTURymRQSzkmHf5GttPXxZ/ckO9Hz9A
XqzXaHcmnauZSmUY12q8rMtbKYP/dN5hUdmR6p44bMgDJehQkmTzJkxbe6t98b+t
8y3YAcK5HclYITC2lBVHSw5z8e9F/B7UmrNxvNkcV5kqdYg3NnVnA292kSMft5zo
WRk1nH4eVARq2dmGQ289QpneHqtMx22RU42m/t8M/v0OUANhlPaDb/RHlyDWJF4=
=4JGY
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"The newly added ftrace_print_array_seq() function had a bug in it.
Luckily, the only user of it didn't make the 4.1 merge window.
But the helper function should be fixed before 4.2 when the users
start coming in"
* tag 'trace-fixes-v4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Make ftrace_print_array_seq compute buf_len
When registering clk-si5351 by platform_data, we should not pass struct clk
for the reference clocks. Drop struct clk from platform_data and rework the
driver to use devm_clk_get of named clock references.
While at it, check for at least one valid input clock and properly prepare/
enable valid reference clocks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: Michael Welling <mwelling@ieee.org>
Reported-by: Jean-Francois Moine <moinejf@free.fr>
Reported-by: Russell King <rmk+linux@arm.linux.org.uk>
Tested-by: Michael Welling <mwelling@ieee.org>
Tested-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Ronny reported that the following scenario is not handled correctly:
T1 (prio = 10)
lock(rtmutex);
T2 (prio = 20)
lock(rtmutex)
boost T1
T1 (prio = 20)
sys_set_scheduler(prio = 30)
T1 prio = 30
....
sys_set_scheduler(prio = 10)
T1 prio = 30
The last step is wrong as T1 should now be back at prio 20.
Commit c365c292d0 ("sched: Consider pi boosting in setscheduler()")
only handles the case where a boosted tasks tries to lower its
priority.
Fix it by taking the new effective priority into account for the
decision whether a change of the priority is required.
Reported-by: Ronny Meeus <ronny.meeus@gmail.com>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: <stable@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Fixes: c365c292d0 ("sched: Consider pi boosting in setscheduler()")
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1505051806060.4225@nanos
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i6KB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/dledford/linux
Pull infiniband updates from Doug Ledford:
"Minor updates for 4.1-rc
Most of the changes are fairly small and well confined. The iWARP
address reporting changes are the only ones that are a medium size. I
had these queued up prior to rc1, but due to the shuffle in
maintainers, they did not get submitted when I expected. My apologies
for that. I feel comfortable with them however due to the testing
they've received, so I left them in this submission"
* tag 'for-linus' of git://github.com/dledford/linux:
MAINTAINERS: Update InfiniBand subsystem maintainer
MAINTAINERS: add include/rdma/ to InfiniBand subsystem
IPoIB/CM: Fix indentation level
iw_cxgb4: Remove negative advice dmesg warnings
IB/core: Fix unaligned accesses
IB/core: change rdma_gid2ip into void function as it always return zero
IB/qib: use arch_phys_wc_add()
IB/qib: add acounting for MTRR
IB/core: dma unmap optimizations
IB/core: dma map/unmap locking optimizations
RDMA/cxgb4: Report the actual address of the remote connecting peer
RDMA/nes: Report the actual address of the remote connecting peer
RDMA/core: Enable the iWarp Port Mapper to provide the actual address of the connecting peer to its clients
iw_cxgb4: enforce qp/cq id requirements
iw_cxgb4: use BAR2 GTS register for T5 kernel mode CQs
iw_cxgb4: 32b platform fixes
iw_cxgb4: Cleanup register defines/MACROS
RDMA/CMA: Canonize IPv4 on IPV6 sockets properly
The only caller to this function (__print_array) was getting it wrong by
passing the array length instead of buffer length. As the element size
was already being passed for other reasons it seems reasonable to push
the calculation of buffer length into the function.
Link: http://lkml.kernel.org/r/1430320727-14582-1-git-send-email-alex.bennee@linaro.org
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
- Fix blkback regression if using persistent grants.
- Fix various event channel related suspend/resume bugs.
- Fix AMD x86 regression with X86_BUG_SYSRET_SS_ATTRS.
- SWIOTLB on ARM now uses frames <4 GiB (if available) so device only
capable of 32-bit DMA work.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJVSiC1AAoJEFxbo/MsZsTRojgH/1zWPD0r5WMAEPb6DFdb7Ga1
SqBbyHFu43axNwZ7EvUzSqI8BKDPbTnScQ3+zC6Zy1SIEfS+40+vn7kY/uASmWtK
LYaYu8nd49OZP8ykH0HEvsJ2LXKnAwqAwvVbEigG7KJA7h8wXo7aDwdwxtZmHlFP
18xRTfHcrnINtAJpjVRmIGZsCMXhXQz4bm0HwsXTTX0qUcRWtxydKDlMPTVFyWR8
wQ2m5+76fQ8KlFsoJEB0M9ygFdheZBF4FxBGHRrWXBUOhHrQITnH+cf1aMVxTkvy
NDwiEebwXUDHacv21onszoOkNjReLsx+DWp9eHknlT/fgPo6tweMM2yazFGm+JQ=
=W683
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.1b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- fix blkback regression if using persistent grants
- fix various event channel related suspend/resume bugs
- fix AMD x86 regression with X86_BUG_SYSRET_SS_ATTRS
- SWIOTLB on ARM now uses frames <4 GiB (if available) so device only
capable of 32-bit DMA work.
* tag 'for-linus-4.1b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Add __GFP_DMA flag when xen_swiotlb_init gets free pages on ARM
hypervisor/x86/xen: Unset X86_BUG_SYSRET_SS_ATTRS on Xen PV guests
xen/events: Set irq_info->evtchn before binding the channel to CPU in __startup_pirq()
xen/console: Update console event channel on resume
xen/xenbus: Update xenbus event channel on resume
xen/events: Clear cpu_evtchn_mask before resuming
xen-pciback: Add name prefix to global 'permissive' variable
xen: Suspend ticks on all CPUs during suspend
xen/grant: introduce func gnttab_unmap_refs_sync()
xen/blkback: safely unmap purge persistent grants
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also an uncore PMU driver fix and an uncore
PMU driver hardware-enablement addition"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Fix segfault if passed with ''.
perf report: Fix -T/--threads option to work again
perf bench numa: Fix immediate meeting of convergence condition
perf bench numa: Fixes of --quiet argument
perf bench futex: Fix hung wakeup tasks after requeueing
perf probe: Fix bug with global variables handling
perf top: Fix a segfault when kernel map is restricted.
tools lib traceevent: Fix build failure on 32-bit arch
perf kmem: Fix compiles on RHEL6/OL6
tools lib api: Undefine _FORTIFY_SOURCE before setting it
perf kmem: Consistently use PRIu64 for printing u64 values
perf trace: Disable events and drain events when forked workload ends
perf trace: Enable events when doing system wide tracing and starting a workload
perf/x86/intel/uncore: Move PCI IDs for IMC to uncore driver
perf/x86/intel/uncore: Add support for Intel Haswell ULT (lower power Mobile Processor) IMC uncore PMUs
perf/x86/intel: Add cpu_(prepare|starting|dying) for core_pmu
The range check for b-tree level parameter in nilfs_btree_root_broken()
is wrong; it accepts the case of "level == NILFS_BTREE_LEVEL_MAX" even
though the level is limited to values in the range of 0 to
(NILFS_BTREE_LEVEL_MAX - 1).
Since the level parameter is read from storage device and used to index
nilfs_btree_path array whose element count is NILFS_BTREE_LEVEL_MAX, it
can cause memory overrun during btree operations if the boundary value
is set to the level parameter on device.
This fixes the broken sanity check and adds a comment to clarify that
the upper bound NILFS_BTREE_LEVEL_MAX is exclusive.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using the new find_closest() macro can result in the following sparse
warnings.
drivers/hwmon/lm85.c:194:16: warning:
incorrect type in initializer (different modifiers)
drivers/hwmon/lm85.c:194:16: expected int *__fc_a
drivers/hwmon/lm85.c:194:16: got int static const [toplevel] *<noident>
drivers/hwmon/lm85.c:210:16: warning:
incorrect type in initializer (different modifiers)
drivers/hwmon/lm85.c:210:16: expected int *__fc_a
drivers/hwmon/lm85.c:210:16: got int const *map
This is because the array passed to find_closest() will typically be
declared as array of constants, but the macro declares a non-constant
pointer to it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move to include/uapi/linux/mpls.h to be externally visibile.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addresses the following kernel logs seen during boot of sparc systems:
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Signed-off-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull crypto fixes from Herbert Xu:
"This fixes a build problem with bcm63xx and yet another fix to the
memzero_explicit function to ensure that the memset is not elided"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: bcm63xx - Fix driver compilation
lib: make memzero_explicit more robust against dead store elimination
Add functionality to enable the port mapper on the passive side to provide to its
clients the actual (non-mapped) ip/tcp address information of the connecting peer
1) Adding remote_info_cb() to process the address info of the connecting peer
The address info is provided by the user space port mapper service when
the connection is initiated by the peer
2) Adding a hash list to store the remote address info
3) Adding functionality to add/remove the remote address info
After the info has been provided to the port mapper client,
it is removed from the hash list
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
* a fix for an issue with hash collision handling in the
rhashtable conversion
* a merge issue - rhashtable removed default shrinking
just before mac80211 was converted, so enable it now
* remove an invalid WARN that can trigger with legitimate
userspace behaviour
* add a struct member missing from kernel-doc that caused
a lot of warnings
-----BEGIN PGP SIGNATURE-----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=sf/A
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-05-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have only a few fixes right now:
* a fix for an issue with hash collision handling in the
rhashtable conversion
* a merge issue - rhashtable removed default shrinking
just before mac80211 was converted, so enable it now
* remove an invalid WARN that can trigger with legitimate
userspace behaviour
* add a struct member missing from kernel-doc that caused
a lot of warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-05-04
Here's the first bluetooth-next pull request for 4.2:
- Various fixes for at86rf230 driver
- ieee802154: trace events support for rdev->ops
- HCI UART driver refactoring
- New Realtek IDs added to btusb driver
- Off-by-one fix for rtl8723b in btusb driver
- Refactoring of btbcm driver for both UART & USB use
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a FUA request enters its DATA stage of flush pipeline, the
request is added to mq requeue list, the request will then be added to
ctx->rq_list. blk_mq_attempt_merge() might merge the request with a bio.
Later when the request is finished the flush pipeline, the
request->__data_len is 0. Then I only saw the bio gets endio called, the
original request never finish.
Adding REQ_FLUSH_SEQ into REQ_NOMERGE_FLAGS looks an easy fix.
stable: 3.15+
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Eliminate 90 of these warnings:
Warning(..//include/net/mac80211.h:1682): No description found for parameter 'drv_priv[0]'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
