o Following patch provides purely cosmetic changes and corrects CodingStyle
guide lines related certain issues like below in kexec related files
o braces for one line "if" statements, "for" loops,
o more than 80 column wide lines,
o No space after "while", "for" and "switch" key words
o Changes:
o take-2: Removed the extra tab before "case" key words.
o take-3: Put operator at the end of line and space before "*/"
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Makes kexec_crashdump() take a pt_regs * as an argument. This allows to
get exact register state at the point of the crash. If we come from direct
panic assertion NULL will be passed and the current registers saved before
crashdump.
This hooks into two places:
die(): check the conditions under which we will panic when calling
do_exit and go there directly with the pt_regs that caused the fatal
fault.
die_nmi(): If we receive an NMI lockup while in the kernel use the
pt_regs and go directly to crash_kexec(). We're probably nested up badly
at this point so this might be the only chance to escape with proper
information.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Vivek Goyal" <vgoyal@in.ibm.com>
o Support for /proc/vmcore interface. This interface exports elf core image
either in ELF32 or ELF64 format, depending on the format in which elf headers
have been stored by crashed kernel.
o Added support for CONFIG_VMCORE config option.
o Removed the dependency on /proc/kcore.
From: "Eric W. Biederman" <ebiederm@xmission.com>
This patch has been refactored to more closely match the prevailing style in
the affected files. And to clearly indicate the dependency between
/proc/kcore and proc/vmcore.c
From: Hariprasad Nellitheertha <hari@in.ibm.com>
This patch contains the code that provides an ELF format interface to the
previous kernel's memory post kexec reboot.
Signed off by Hariprasad Nellitheertha <hari@in.ibm.com>
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for retrieving the address of elf core header if one
is passed in command line.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch provides the interfaces necessary to read the dump contents,
treating it as a high memory device.
Signed off by Hariprasad Nellitheertha <hari@in.ibm.com>
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch exports kexec global variable "crash_notes" to user space
through sysfs as kernel attribute in /sys/kernel.
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a minor bug fix in kexec to resolve the problem of loading panic
kernel with initrd.
o Problem: Loading a capture kenrel fails if initrd is also being loaded.
This has been observed for vmlinux image for kexec on panic case.
o This patch fixes the problem. In segment location and size verification
logic, minor correction has been done. Segment memory end (mend) should be
mstart + memsz - 1. This one byte offset was source of failure for initrd
loading which was being loaded at hole boundary.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the architecture independent implementation the
sys_kexec_load, the compat_sys_kexec_load system calls.
Kexec on panic support has been integrated into the core patch and is
relatively clean.
In addition the hopefully architecture independent option
crashkernel=size@location has been docuemented. It's purpose is to reserve
space for the panic kernel to live, and where no DMA transfer will ever be
setup to access.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a new preemption model: 'Voluntary Kernel Preemption'. The
3 models can be selected from a new menu:
(X) No Forced Preemption (Server)
( ) Voluntary Kernel Preemption (Desktop)
( ) Preemptible Kernel (Low-Latency Desktop)
we still default to the stock (Server) preemption model.
Voluntary preemption works by adding a cond_resched()
(reschedule-if-needed) call to every might_sleep() check. It is lighter
than CONFIG_PREEMPT - at the cost of not having as tight latencies. It
represents a different latency/complexity/overhead tradeoff.
It has no runtime impact at all if disabled. Here are size stats that show
how the various preemption models impact the kernel's size:
text data bss dec hex filename
3618774 547184 179896 4345854 424ffe vmlinux.stock
3626406 547184 179896 4353486 426dce vmlinux.voluntary +0.2%
3748414 548640 179896 4476950 445016 vmlinux.preempt +3.5%
voluntary-preempt is +0.2% of .text, preempt is +3.5%.
This feature has been tested for many months by lots of people (and it's
also included in the RHEL4 distribution and earlier variants were in Fedora
as well), and it's intended for users and distributions who dont want to
use full-blown CONFIG_PREEMPT for one reason or another.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only sane way to clean up the current 3 lock_kernel() variants seems to
be to remove the spinlock-based BKL implementations altogether, and to keep
the semaphore-based one only. If we dont want to do that for whatever
reason then i'm afraid we have to live with the current complexity. (but
i'm open for other cleanup suggestions as well.)
To explore this possibility we'll (at a minimum) have to know whether the
semaphore-based BKL works fine on plain SMP too. The patch below enables
this.
The patch may make sense in isolation as well, as it might bring
performance benefits: code that would formerly spin on the BKL spinlock
will now schedule away and give up the CPU. It might introduce performance
regressions as well, if any performance-critical code uses the BKL heavily
and gets overscheduled due to the semaphore. I very much hope there is no
such performance-critical codepath left though.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch consolidates the CONFIG_PREEMPT and CONFIG_PREEMPT_BKL
preemption options into kernel/Kconfig.preempt. This, besides reducing
source-code, also enables more centralized tweaking of preemption related
options.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds the core update_cpu_domains code and updated cpusets documentation
Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Acked-by: Paul Jackson <pj@sgi.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patches add dynamic sched domains functionality that was
extensively discussed on lkml and lse-tech. I would like to see this added to
-mm
o The main advantage with this feature is that it ensures that the scheduler
load balacing code only balances against the cpus that are in the sched
domain as defined by an exclusive cpuset and not all of the cpus in the
system. This removes any overhead due to load balancing code trying to
pull tasks outside of the cpu exclusive cpuset only to be prevented by
the tasks' cpus_allowed mask.
o cpu exclusive cpusets are useful for servers running orthogonal
workloads such as RT applications requiring low latency and HPC
applications that are throughput sensitive
o It provides a new API partition_sched_domains in sched.c
that makes dynamic sched domains possible.
o cpu_exclusive cpusets sets are now associated with a sched domain.
Which means that the users can dynamically modify the sched domains
through the cpuset file system interface
o ia64 sched domain code has been updated to support this feature as well
o Currently, this does not support hotplug. (However some of my tests
indicate hotplug+preempt is currently broken)
o I have tested it extensively on x86.
o This should have very minimal impact on performance as none of
the fast paths are affected
Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Acked-by: Paul Jackson <pj@sgi.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Presently, a process without the capability CAP_SYS_NICE can not change
its own policy, which is OK.
But it can also not decrease its RT priority (if scheduled with policy
SCHED_RR or SCHED_FIFO), which is what this patch changes.
The rationale is the same as for the nice value: a process should be
able to require less priority for itself. Increasing the priority is
still not allowed.
This is for example useful if you give a multithreaded user process a RT
priority, and the process would like to organize its internal threads
using priorities also. Then you can give the process the highest
priority needed N, and the process starts its threads with lower
priorities: N-1, N-2...
The POSIX norm says that the permissions are implementation specific, so
I think we can do that.
In a sense, it makes the permissions consistent whatever the policy is:
with this patch, process scheduled by SCHED_FIFO, SCHED_RR and
SCHED_OTHER can all decrease their priority.
From: Ingo Molnar <mingo@elte.hu>
cleaned up and merged to -mm.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The maximum rebalance interval allowed by the multiprocessor balancing
backoff is often not large enough to handle corner cases where there are
lots of tasks pinned on a CPU. Suresh reported:
I see system livelock's if for example I have 7000 processes
pinned onto one cpu (this is on the fastest 8-way system I
have access to).
After this patch, the machine is reported to go well above this number.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidate balance-on-exec with balance-on-fork. This is made easy by the
sched-domains RCU patches.
As well as the general goodness of code reduction, this allows the runqueues
to be unlocked during balance-on-fork.
schedstats is a problem. Maybe just have balance-on-event instead of
distinguishing fork and exec?
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One of the problems with the multilevel balance-on-fork/exec is that it needs
to jump through hoops to satisfy sched-domain's locking semantics (that is,
you may traverse your own domain when not preemptable, and you may traverse
others' domains when holding their runqueue lock).
balance-on-exec had to potentially migrate between more than one CPU before
finding a final CPU to migrate to, and balance-on-fork needed to potentially
take multiple runqueue locks.
So bite the bullet and make sched-domains go completely RCU. This actually
simplifies the code quite a bit.
From: Ingo Molnar <mingo@elte.hu>
schedstats RCU fix, and a nice comment on for_each_domain, from Ingo.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The fundamental problem that Suresh has with balance on exec and fork is that
it only tries to balance the top level domain with the flag set.
This was worked around by removing degenerate domains, but is still a problem
if people want to start using more complex sched-domains, especially
multilevel NUMA that ia64 is already using.
This patch makes balance on fork and exec try balancing over not just the top
most domain with the flag set, but all the way down the domain tree.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove degenerate scheduler domains during the sched-domain init.
For example on x86_64, we always have NUMA configured in. On Intel EM64T
systems, top most sched domain will be of NUMA and with only one sched_group
in it.
With fork/exec balances(recent Nick's fixes in -mm tree), we always endup
taking wrong decisions because of this topmost domain (as it contains only one
group and find_idlest_group always returns NULL). We will endup loading HT
package completely first, letting active load balance kickin and correct it.
In general, this patch also makes sense with out recent Nick's fixes in -mm.
From: Nick Piggin <nickpiggin@yahoo.com.au>
Modified to account for more than just sched_groups when scanning for
degenerate domains by Nick Piggin. And allow a runqueue's sd to go NULL
rather than keep a single degenerate domain around (this happens when you run
with maxcpus=1).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the last 2 places that directly access a runqueue's sched-domain and
assume it cannot be NULL.
That allows the use of NULL for domain, instead of a dummy domain, to signify
no balancing is to happen. No functional changes.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of requiring architecture code to interact with the scheduler's
locking implementation, provide a couple of defines that can be used by the
architecture to request runqueue unlocked context switches, and ask for
interrupts to be enabled over the context switch.
Also replaces the "switch_lock" used by these architectures with an oncpu
flag (note, not a potentially slow bitflag). This eliminates one bus
locked memory operation when context switching, and simplifies the
task_running function.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reimplement the balance on exec balancing to be sched-domains aware. Use this
to also do balance on fork balancing. Make x86_64 do balance on fork over the
NUMA domain.
The problem that the non sched domains aware blancing became apparent on dual
core, multi socket opterons. What we want is for the new tasks to be sent to
a different socket, but more often than not, we would first load up our
sibling core, or fill two cores of a single remote socket before selecting a
new one.
This gives large improvements to STREAM on such systems.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the very aggressive idle stuff that has recently gone into 2.6 - it is
going against the direction we are trying to go. Hopefully we can regain
performance through other methods.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do less affine wakeups. We're trying to reduce dbt2-pgsql idle time
regressions here... make sure we don't don't move tasks the wrong way in an
imbalance condition. Also, remove the cache coldness requirement from the
calculation - this seems to induce sharp cutoff points where behaviour will
suddenly change on some workloads if the load creeps slightly over or under
some point. It is good for periodic balancing because in that case have
otherwise have no other context to determine what task to move.
But also make a minor tweak to "wake balancing" - the imbalance tolerance is
now set at half the domain's imbalance, so we get the opportunity to do wake
balancing before the more random periodic rebalancing gets preformed.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do CPU load averaging over a number of different intervals. Allow each
interval to be chosen by sending a parameter to source_load and target_load.
0 is instantaneous, idx > 0 returns a decaying average with the most recent
sample weighted at 2^(idx-1). To a maximum of 3 (could be easily increased).
So generally a higher number will result in more conservative balancing.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the special casing for idle CPU balancing. Things like this are
hurting for example on SMT, where are single sibling being idle doesn't really
warrant a really aggressive pull over the NUMA domain, for example.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These conditions should now be impossible, and we need to fix them if they
happen.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SMT balancing has a couple of problems. Firstly, active_load_balance is too
complex - basically it should be a dumb helper for when the periodic balancer
has determined there is an imbalance, but gets stuck because the task is
running.
So rip out all its "smarts", and just make it move one task to the target CPU.
Second, the busy CPU's sched-domain tree was being used for active balancing.
This means that it may not see that nr_balance_failed has reached a critical
level. So use the target CPU's sched-domain tree for this. We can do this
because we hold its runqueue lock.
Lastly, reset nr_balance_failed to a point where we allow cache hot migration.
This will help ensure active load balancing is successful.
Thanks to Suresh Siddha for pointing out these issues.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up active load balancing a bit so it doesn't get called when it shouldn't.
Reset the nr_balance_failed counter at more points where we have found
conditions to be balanced. This reduces too aggressive active balancing seen
on some workloads.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
John Hawkes explained the problem best:
A large number of processes that are pinned to a single CPU results
in every other CPU's load_balance() seeing this overloaded CPU as
"busiest", yet move_tasks() never finds a task to pull-migrate. This
condition occurs during module unload, but can also occur as a
denial-of-service using sys_sched_setaffinity(). Several hundred
CPUs performing this fruitless load_balance() will livelock on the
busiest CPU's runqueue lock. A smaller number of CPUs will livelock
if the pinned task count gets high.
Expanding slightly on John's patch, this one attempts to work out whether the
balancing failure has been due to too many tasks pinned on the runqueue. This
allows it to be basically invisible to the regular blancing paths (ie. when
there are no pinned tasks). We can use this extra knowledge to shut down the
balancing faster, and ensure the migration threads don't start running which
is another problem observed in the wild.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
New sched-domains code means we don't get spans with offline CPUs in
them.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Show swsuspend only on .config where it can compile. I got this on PPC32 &&
SMP:
kernel/power/smp.c:24: error: storage size of `ctxt' isn't known
Also mark swsusp as no longer experimental.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the cpu hotplug case, per-cpu data possibly isn't initialized even the
system state is 'running'. As the comments say in the original code, some
console drivers assume per-cpu resources have been allocated. radeon fb is
one such driver, which uses kmalloc. After a CPU is down, the per-cpu data
of slab is freed, so the system crashed when printing some info.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch moves the recalculation of nr_copy_pages so that the right
number is used in the calculation of the size of memory and swap needed.
It prevents swsusp from attempting to suspend if there is not enough memory
and/or swap (which is unlikely anyway).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch cleans up whitespace in swsusp.c (a bit):
- removes any trailing whitespace
- adds spaces after if, for, for_each_pbe, for_each_zone etc., wherever
necessary.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch removes the unnecessary function does_collide_order().
This function is no longer necessary, as currently there are only 0-order
allocations in swsusp, and the use of it is confusing.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without this patch, Linux provokes emergency disk shutdowns and
similar nastiness. It was in SuSE kernels for some time, IIRC.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using CPU hotplug to support suspend/resume SMP. Both S3 and S4 use
disable/enable_nonboot_cpus API. The S4 part is based on Pavel's original S4
SMP patch.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(The i386 CPU hotplug patch provides infrastructure for some work which Pavel
is doing as well as for ACPI S3 (suspend-to-RAM) work which Li Shaohua
<shaohua.li@intel.com> is doing)
The following provides i386 architecture support for safely unregistering and
registering processors during runtime, updated for the current -mm tree. In
order to avoid dumping cpu hotplug code into kernel/irq/* i dropped the
cpu_online check in do_IRQ() by modifying fixup_irqs(). The difference being
that on cpu offline, fixup_irqs() is called before we clear the cpu from
cpu_online_map and a long delay in order to ensure that we never have any
queued external interrupts on the APICs. There are additional changes to s390
and ppc64 to account for this change.
1) Add CONFIG_HOTPLUG_CPU
2) disable local APIC timer on dead cpus.
3) Disable preempt around irq balancing to prevent CPUs going down.
4) Print irq stats for all possible cpus.
5) Debugging check for interrupts on offline cpus.
6) Hacky fixup_irqs() to redirect irqs when cpus go off/online.
7) play_dead() for offline cpus to spin inside.
8) Handle offline cpus set in flush_tlb_others().
9) Grab lock earlier in smp_call_function() to prevent CPUs going down.
10) Implement __cpu_disable() and __cpu_die().
11) Enable local interrupts in cpu_enable() after fixup_irqs()
12) Don't fiddle with NMI on dead cpu, but leave intact on other cpus.
13) Program IRQ affinity whilst cpu is still in cpu_online_map on offline.
Signed-off-by: Zwane Mwaikambo <zwane@linuxpower.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another rollup of patches which give various symbols static scope
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds version and srcversion files to
/sys/module/${modulename} containing the version and srcversion fields
of the module's modinfo section (if present).
/sys/module/e1000
|-- srcversion
`-- version
This patch differs slightly from the version posted in January, as it
now uses the new kstrdup() call in -mm.
Why put this in sysfs?
a) Tools like DKMS, which deal with changing out individual kernel
modules without replacing the whole kernel, can behave smarter if they
can tell the version of a given module. The autoinstaller feature, for
example, which determines if your system has a "good" version of a
driver (i.e. if the one provided by DKMS has a newer verson than that
provided by the kernel package installed), and to automatically compile
and install a newer version if DKMS has it but your kernel doesn't yet
have that version.
b) Because sysadmins manually, or with tools like DKMS, can switch out
modules on the file system, you can't count on 'modinfo foo.ko', which
looks at /lib/modules/${kernelver}/... actually matching what is loaded
into the kernel already. Hence asking sysfs for this.
c) as the unbind-driver-from-device work takes shape, it will be
possible to rebind a driver that's built-in (no .ko to modinfo for the
version) to a newly loaded module. sysfs will have the
currently-built-in version info, for comparison.
d) tech support scripts can then easily grab the version info for what's
running presently - a question I get often.
There has been renewed interest in this patch on linux-scsi by driver
authors.
As the idea originated from GregKH, I leave his Signed-off-by: intact,
though the implementation is nearly completely new. Compiled and run on
x86 and x86_64.
From: Matthew Dobson <colpatch@us.ibm.com>
build fix
From: Thierry Vignaud <tvignaud@mandriva.com>
build fix
From: Matthew Dobson <colpatch@us.ibm.com>
warning fix
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch makes the following changes:
(1) There's a new special key type called ".request_key_auth".
This is an authorisation key for when one process requests a key and
another process is started to construct it. This type of key cannot be
created by the user; nor can it be requested by kernel services.
Authorisation keys hold two references:
(a) Each refers to a key being constructed. When the key being
constructed is instantiated the authorisation key is revoked,
rendering it of no further use.
(b) The "authorising process". This is either:
(i) the process that called request_key(), or:
(ii) if the process that called request_key() itself had an
authorisation key in its session keyring, then the authorising
process referred to by that authorisation key will also be
referred to by the new authorisation key.
This means that the process that initiated a chain of key requests
will authorise the lot of them, and will, by default, wind up with
the keys obtained from them in its keyrings.
(2) request_key() creates an authorisation key which is then passed to
/sbin/request-key in as part of a new session keyring.
(3) When request_key() is searching for a key to hand back to the caller, if
it comes across an authorisation key in the session keyring of the
calling process, it will also search the keyrings of the process
specified therein and it will use the specified process's credentials
(fsuid, fsgid, groups) to do that rather than the calling process's
credentials.
This allows a process started by /sbin/request-key to find keys belonging
to the authorising process.
(4) A key can be read, even if the process executing KEYCTL_READ doesn't have
direct read or search permission if that key is contained within the
keyrings of a process specified by an authorisation key found within the
calling process's session keyring, and is searchable using the
credentials of the authorising process.
This allows a process started by /sbin/request-key to read keys belonging
to the authorising process.
(5) The magic KEY_SPEC_*_KEYRING key IDs when passed to KEYCTL_INSTANTIATE or
KEYCTL_NEGATE will specify a keyring of the authorising process, rather
than the process doing the instantiation.
(6) One of the process keyrings can be nominated as the default to which
request_key() should attach new keys if not otherwise specified. This is
done with KEYCTL_SET_REQKEY_KEYRING and one of the KEY_REQKEY_DEFL_*
constants. The current setting can also be read using this call.
(7) request_key() is partially interruptible. If it is waiting for another
process to finish constructing a key, it can be interrupted. This permits
a request-key cycle to be broken without recourse to rebooting.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-Off-By: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch makes it possible to pass a session keyring through to the
process spawned by call_usermodehelper(). This allows patch 3/3 to pass an
authorisation key through to /sbin/request-key, thus permitting better access
controls when doing just-in-time key creation.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the upcoming aio_down patch, it is useful to store a private data
pointer in the kiocb's wait_queue. Since we provide our own wake up
function and do not require the task_struct pointer, it makes sense to
convert the task pointer into a generic private pointer.
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid taking the tasklist_lock in sys_times if the process is single
threaded. In a NUMA system taking the tasklist_lock may cause a bouncing
cacheline if multiple independent processes continually call sys_times to
measure their performance.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes recalc_sigpending() to work correctly with tasks which are
being freezed.
The problem is that freeze_processes() sets PF_FREEZE and TIF_SIGPENDING
flags on tasks, but recalc_sigpending() called from e.g.
sys_rt_sigtimedwait or any other kernel place will clear TIF_SIGPENDING due
to no pending signals queued and the tasks won't be freezed until it
recieves a real signal or freezed_processes() fail due to timeout.
Signed-Off-By: Kirill Korotaev <dev@sw.ru>
Signed-Off-By: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new `suid_dumpable' sysctl:
This value can be used to query and set the core dump mode for setuid
or otherwise protected/tainted binaries. The modes are
0 - (default) - traditional behaviour. Any process which has changed
privilege levels or is execute only will not be dumped
1 - (debug) - all processes dump core when possible. The core dump is
owned by the current user and no security is applied. This is intended
for system debugging situations only. Ptrace is unchecked.
2 - (suidsafe) - any binary which normally would not be dumped is dumped
readable by root only. This allows the end user to remove such a dump but
not access it directly. For security reasons core dumps in this mode will
not overwrite one another or other files. This mode is appropriate when
adminstrators are attempting to debug problems in a normal environment.
(akpm:
> > +EXPORT_SYMBOL(suid_dumpable);
>
> EXPORT_SYMBOL_GPL?
No problem to me.
> > if (current->euid == current->uid && current->egid == current->gid)
> > current->mm->dumpable = 1;
>
> Should this be SUID_DUMP_USER?
Actually the feedback I had from last time was that the SUID_ defines
should go because its clearer to follow the numbers. They can go
everywhere (and there are lots of places where dumpable is tested/used
as a bool in untouched code)
> Maybe this should be renamed to `dump_policy' or something. Doing that
> would help us catch any code which isn't using the #defines, too.
Fair comment. The patch was designed to be easy to maintain for Red Hat
rather than for merging. Changing that field would create a gigantic
diff because it is used all over the place.
)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
