after the recent changes to wired drivers to use only
netif_carrier_off the driver can have outstanding tx work to
complete that will never complete once link is down. Since the
intel hardware will hold this tx work forever, the driver
notices a tx timeout condition internally and might try
to instigate printk and reset of the part with a
netif_stop_queue, which doesn't work because link is down.
Don't bother arming to tx hang detection when link is down.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out that the Intel wired ethernet drivers do not need to
wake the tx queue since netif_carrier_on/off will take care of the qdisc
management in order to guarantee the correct handling of the transmit
routine enable state.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
in addition this driver appeared to need a netif_start_queue at
the end of open.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This code updates ixgb so that it can use the skb_dma_map/unmap functions
to map the buffers. In addition it also updates the tx hang logic to use
time_stamp instead of dma to determine if it has detected a tx hang.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we removed the network device argument from several
NAPI interfaces in 908a7a16b8
("net: Remove unused netdev arg from some NAPI interfaces.")
several drivers now started getting unused variable warnings.
This fixes those up.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to network device ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the newly introduced pci_ioremap_bar() function in drivers/net.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It was pointed out by Breno Leitao <leitao@linux.vnet.ibm.com> that
ixgb would crash on PPC when an IOMMU was in use, if change_mtu was
called.
It appears to be a pretty simple issue in the driver that wasn't discovered
because most systems don't run with an IOMMU. The driver needs to only unmap
buffers that are mapped (duh).
CC: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently VLAN filtering is enabled when the first VLAN is added.
Obviously before that there's no point in receiving any VLAN packets.
Now that we disable VLAN filtering in promiscous mode, we can keep
the VLAN filters enabled the remaining time.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed in this thread:
http://www.mail-archive.com/netdev@vger.kernel.org/msg53976.html
promiscous mode means to disable *all* filters. Currently only unicast
and multicast filtering is disabled. This patch changes all Intel
drivers to also disable VLAN filtering.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
network maintainers suggest NAPI only drivers are the only way to go.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
cleaned up some spacing in defines
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
calls to kfree_skb_any are only required when calling kfree
from interrupt context.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
rx cleanup should look more like our other drivers that have evolved
to nicer performance levels over time. Changes consist of refilling
tx buffers to hardware more often, some minor assignment cleanups.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
this patch is trivial but because I want to have everything be nice and
tidy I'm updating it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
copybreak code was already in the driver, allow the user to turn it
off if they don't like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
a) kernel developers suggest LLTX is broken and unsafe to use, remove it.
b) remember to pre-stop the queue if we won't have room
c) removing lltx means we can remove our tx lock
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgb needs to call flush scheduled work to flush any timers before
unregistering the netdev.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
some random coverage testing found that when changing mtu
under heavy traffic load, NAPI would use the rx_buffer_len variable
after it had been changed by change_mtu.
Similar to e1000 bugs found long ago.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
a user pointed out that setting variables out of order with respect
to the checks we make for tx timeout handling could result in a race
where ->dma was set but ->time_stamp was set to the old value.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
in order to prevent the case where poll_disable is waiting
on our device to permanently, check the flag to make sure we're not
down or closing down before re-enabling interrupts.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgb hardware (not ixgbe) has a problem where it might dma past the
end of a buffer in certain cases. leave 8 bytes extra room.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
there was one more bug hidden in the prefetch routines in ixgb hardware
that force us to remove it completely. Writebacks were being done on
descriptors with stale data due to internal hardware fifo corruption.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
this patch has been made to many other drivers in kernel to fix
the storage of 64 bit resources in 32 bit variables.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
back when maybe stop tx was added to the ixgb driver some mistakes
were made and the driver
a) didn't remove the tx lock, which is now un-necessary
b) didn't change the restart code to be compliant with maybe_stop
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The vlan_hwaccel_{rx,receive_skb} functions expect the full TCI field
for priority mappings, don't truncate the upper 4 bits.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conglomerate of 4 separate patches by Joe.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgb can remove irq_sem by auditing all the call sites to make sure
that each of them makes sure the adapter is in the correct state
before re-enabling interrupts. after doing this to all of our other
drivers it is becoming easier.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
> send me a patch for e1000 and for ixgb and I'll happily apply those :)
boolean_t to bool
TRUE to true
FALSE to false
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
