We should select FSR also to be driven by McBSP, not only FSX.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In soc_new_compress() when rtd->dai_link->dynamic is set, we create the pcm
substreams with this call:
ret = snd_pcm_new_internal(rtd->card->snd_card, new_name, num,
1, 0, &be_pcm);
which passes 0 as capture_count leading to
be_pcm->streams[SNDRV_PCM_STREAM_CAPTURE].substream
being NULL, hence when trying to set rtd a few lines below we get an oops.
Fix by using rtd->dai_link->dpcm_playback and rtd->dai_link->dpcm_capture as
playback_count and capture_count to snd_pcm_new_internal().
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
There is only one I2S I/F, AD/DA path must operate to the same
format.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the path name for mux to get rid of the following warning:
--->8---
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTR
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTR
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACL
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACL
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACR
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACR
---8<---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If asoc_simple_card_probe() fails, asoc_simple_card_unref() may be
called before dev_set_drvdata(), causing a NULL pointer dereference in
asoc_simple_card_unref():
Unable to handle kernel NULL pointer dereference at virtual address 000000d4
...
PC is at asoc_simple_card_unref+0x14/0x48
LR is at asoc_simple_card_probe+0x3d4/0x40c
This typically happens because asoc_simple_card_parse_of() returns
-EPROBE_DEFER, but other failure modes are possible.
devm_snd_soc_register_card()/snd_soc_register_card() may fail either
before or after dev_set_drvdata().
Pass a snd_soc_card pointer instead of a platform_device pointer to
asoc_simple_card_unref() to fix this.
Note that if CONFIG_OF_DYNAMIC=n, of_node_put() is a dummy, and gcc may
optimize away the loop over card->dai_link, never actually dereferencing
card, and thus avoiding the crash...
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: e512e001da ("ASoC: simple-card: Fix the reference count of device nodes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The following crash happens when trying to unload the snd_soc_imx_wm8962 module
while playback is active:
[ 208.666868] Unable to handle kernel paging request at virtc
[ 208.674110] pgd = 80004000
[ 208.676867] [7f06541c] *pgd=4c334811, *pte=00000000, *ppte=00000000
[ 208.683211] Internal error: Oops: 80000007 [#1] SMP ARM
[ 208.688445] Modules linked in: snd_soc_wm8962 snd_soc_fsl_ssi snd_soc_imx_audmux imx_pcm_fiq evbug]
...
In order to avoid such problem, fill the card owner field as suggested by
Lars-Peter Clausen:
"But looking at the source it seems that this is a core feature of ALSA and at
least for the card module itself it will do the ref-counting when a stream is
started/stopped. And we even support setting the owner of a card in ASoC.
It's just that pretty much no ASoC card driver bothers to set the owner field
in the snd_soc_card struct. So this particular problem can be fixed by updating
the imx-wm8962 driver to set the owner field."
By doing as suggested, we no longer see the crash when attempting to unload the
snd_soc_imx_wm8962 module while playback is active:
$ modprobe -r snd_soc_imx_wm8962
modprobe: can't unload module snd_soc_imx_wm8962: Resource temporarily
unavailable
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP programs are listed out of order.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The patch modified the behavior that updates the PLL parameter. It set the
update bit before the PLL power up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 2ffa531078 ("ASoC: fsl_ssi: Fix module unbound") changed the way to
retrieve the irq number from irq_of_parse_and_map() to platform_get_irq(), but
missed to updated the irq error check accordingly.
We should test for negative irq number and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not send IPC stream commands to FW when the stream is
NULL, dereference the NULL pointer may also occur without precheck.
Here add NULL pointer checks for these stream APIs.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8960 codec can't support sample rate 11250, it must be 11025.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The probe routine was disabling the clock even
if the system was configured successfully. Add
a return statement to leave clocks enabled.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset of block allocator, ba->offset, should not be changed during
fixed address allocating, for the caller may treat it as the offset of
allocated memory and use it. In the case that we allocate more than 1
blocks, we should make sure this offset is correct.
Here introduces a temp allocator for the later continuous allocating.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ts3a227e does not trigger interrupt to report jack status when system
boots from warm reset because ts3a227e's power remains on during warm reset.
Read jack status at probe to get current jack status.
Note that if system boots from EC reset, then this issue will not
happen.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new wildcard msbits constraints instead of installing a constraint
for each available sample format width.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The xDC field should have 5 bit width according to Reference Manual.
Thus this patch fixes it.
Signed-off-by: Aurelien BOUIN <a_bouin@yahoo.fr>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Set Transmit Data Level(TDL) and Receive Data Level(RDL) to 16 samples.
Without this setting, the TDL is default to be 0x00 (means 0 sample),
and the RDL is default to be 0x1f (means 32 samples).
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since RK3288 DMAC's burst length only support max to 4, here
set maxburst of playback and capture dma data to 4.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to description about "Transmit Data Level",
This bit field controls the level at which a DMA request
is made by the transmit logic.
It is equal to the watermark level.
That is, the dma_tx_req signal is generated when the number
of valid data entries in the TXFIFO
(TXFIFO0 if CSR=00
TXFIFO1 if CSR=01
TXFIFO2 if CSR=10
TXFIFO3 if CSR=11)
is equal to or below this field value.
Different to receive data level, transmit data level does not need
to "-1".
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the duplicated PLL1 connections of the adc stereo filters,
and remove the PLL1 connections of the DACs because the PLL1 should be
connected to dac filters.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the filter powers of the dac mono3 and mono4, and remove the connection
of dac stereo1 filter that connect to DAC1 MIX.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable some modules from other than base FW, according
to FW interface spec, we need pass the correct entry point
param to FW, so here store the entry_point read from FW
file for later usage.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For block span more than 1 section, when allocate it from
a free block, we need allocate the remain buffers within
the block, and then continue alloc the rest of needed
size buffer.
Here also make sure this free block is moved from free
list to used list, and add it to block_list which may
be used for power gating disabling later.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Both codec and cpu DAI prepare print the same error message making it a bit
more difficult to grep quickly from sources. Fix this by telling it
explicitly.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_kcontrol_chip should return snd_soc_component instead of
snd_soc_codec
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
System clock is necessary for rt5670 JD function. We assume system
clock source will be set in machine driver. So there are two things
left we should do in codec driver.
1. Set sysclk to codec internal clock in probe since machine driver
may not do that before JD function is registered.
2. Power up PLL once sysclk source is switched to PLL.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds runtime PM support on rt5670 codec.
Signed-off-by: Lin Mengdong <mengdong.lin@intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/intel/sst/sst_acpi.c:248:5: warning:
symbol 'sst_acpi_probe' was not declared. Should it be static?
sound/soc/intel/sst/sst_acpi.c:335:5: warning:
symbol 'sst_acpi_remove' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_sst_bytcr_dpcm_rt5640 doesn't autoload because MODULE_ALIAS doesn't
match with "bytt100_rt5640" platform device.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BYTCR DSP firmware is in intel/ subdirectory. See linux-firmware.git
commit d562a3b63632 ("linux-firmware: add sst audio firmware for baytrail
platforms").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Designware core can be configured with up to four stereo channels.
Each stereo channel is individually configured so, when the driver's
hw_params call is made, each requested stereo channel has to be
programmed.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
