Clean up dump_bfin_mem so that it will display
content from the kernel, as well as l1 instruction, when deferred
HW errors happen, print out the last frame info if it makes sense.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
On BF548-EZKIT, build kernel faills with power management, video and audio enabled.
This patch fix this.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
modified CMD_TIMEOUT and DAT_TIMEOUT to CMD_TIME_OUT and DAT_TIME_OUT
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3719
When the CPLBs get a miss, we do:
- find a victim in the HW table
- remove the victim
- find the replacement in the software table
- put it into the HW table.
If we can't find a replacement in the software table, we accidently
leave a duplicate in the HW table. This patch ensures that duplicate
is marked as not valid.
What we should do is find the replacement in the software table, before
we find a victim in the HW table - but its too late in the release cycle
to do that much restructuring of this code.
Rather that duplicate code, connect Hardware Errors (irq5) into trap_c,
so user space processes get killed properly.
The rest of irq_panic() can be moved into traps.c (later)
There is still a small corner case that causes problems when a
pheriperal interrupt goes off a single cycle before a user space
hardware error. This causes a kernel panic, rather than the user
space process being killed.
But, this checkin makes things work in 99.9% of the cases, and is a vast
improvement from what is there today (which fails 100% of the time).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (63 commits)
ide: remove REQ_TYPE_ATA_CMD
ide: switch ide_cmd_ioctl() to use REQ_TYPE_ATA_TASKFILE requests
ide: switch set_xfer_rate() to use REQ_TYPE_ATA_TASKFILE requests
ide: fix final status check in drive_cmd_intr()
ide: check BUSY and ERROR status bits before reading data in drive_cmd_intr()
ide: don't enable local IRQs for PIO-in in driver_cmd_intr() (take 2)
ide: convert "empty" REQ_TYPE_ATA_CMD requests to use REQ_TYPE_ATA_TASKFILE
ide: initialize rq->cmd_type in ide_init_drive_cmd() callers
ide: use wait_drive_not_busy() in drive_cmd_intr() (take 2)
ide: kill DATA_READY define
ide: task_end_request() fix
ide: use rq->nr_sectors in task_end_request()
ide: remove needless ->cursg clearing from task_end_request()
ide: set IDE_TFLAG_IN_* flags before queuing/executing command
ide-tape: fix handling of non-special requests in ->end_request method
ide: fix final status check in task_in_intr()
ide: clear HOB bit for REQ_TYPE_ATA_CMD requests in ide_end_drive_cmd()
ide: fix ->io_32bit race in ide_taskfile_ioctl()
cmd64x: remove /proc/ide/cmd64x
ide: remove broken disk byte-swapping support
...
Based on the earlier work by Tejun Heo.
All users are gone so we can finally remove it.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on the earlier work by Tejun Heo.
Switch set_xfer_rate() to use REQ_TYPE_ATA_TASKFILE requests
and make ide_wait_cmd() static.
There should be no functionality changes caused by this patch.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use wait_drive_not_busy() in drive_cmd_intr().
v2:
* Fix wait_drive_not_busy() comment (noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
task_end_request() modified to always call ide_end_drive_cmd()
for taskfile requests. Previously, ide_end_drive_cmd() was
called only when IDE_TFLAG_FLAGGED was set. Also,
ide_dma_intr() is modified to use task_end_request().
Enables TASKFILE ioctls to get valid register outputs on
successful completion.
Bart:
- ported it over recent IDE changes
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_{HOB,TF,DEVICE} defines.
* Set IDE_TFLAG_IN_* flags in {do_rw,ide_no_data,ide_raw}_taskfile() users.
* Remove no longer needed ->tf_flags setup from ide_end_drive_cmd().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In ide_taskfile_ioctl(), there was a race condition involving
drive->io_32bit. It was cleared and restored during ioctl
requests but there was no synchronization with other requests.
So, other requests could execute with the altered ->io_32bit
setting or updated drive->io_32bit could be overwritten by
ide_taskfile_ioctl().
This patch adds IDE_TFLAG_IO_16BIT flag to indicate to
ide_pio_datablock() that 16-bit I/O is needed regardless of
drive->io_32bit settting.
Bart:
- ported it over recent IDE changes
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove broken disk byte-swapping support:
- it can cause a data corruption on SMP (or if using PREEMPT on UP)
- all data coming from disk are byte-swapped by taskfile_*_data() which
results in incorrect identify data being reported by /proc/ide/ and IOCTLs
- "hdx=bswap/byteswap" kernel parameter has been broken on m68k host drivers
(including Atari/Q40 ones) since 2.5.x days (because of 'hwif' zero-ing)
- byte-swapping is limited to PIO transfers (for working with TiVo disks on
x86 machines using user-space solutions or dm-byteswap should result in
much better performance because DMA can be used)
For previous discussions please see:
http://www.ussg.iu.edu/hypermail/linux/kernel/0201.0/0768.htmlhttp://lkml.org/lkml/2004/2/28/111
[ I have dm-byteswap device mapper target if somebody is interested
(patch is for 2.6.4 though but I'll dust it off if needed). ]
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make remaining built-in only IDE host drivers modular, add ide-scan-pci.c
file for probing PCI host drivers registered with IDE core (special case
for built-in IDE and CONFIG_IDEPCI_PCIBUS_ORDER=y) and then take care of
the ordering in which all IDE host drivers are probed when IDE is built-in
during link time.
* Move probing of gayle, falconide, macide, q40ide and buddha (m68k arch
specific) host drivers, before PCI ones (no PCI on m68k), ide-cris (cris
arch specific), cmd640 (x86 arch specific) and pmac (ppc arch specific).
* Move probing of ide-cris (cris arch specific) host driver before cmd640
(x86 arch specific).
* Move probing of mpc8xx (ppc specific) host driver before ide-pnp (depends
on ISA and none of ppc platform that use mpc8xx supports ISA) and ide-h8300
(h8300 arch specific).
* Add "probe_vlb" kernel parameter to cmd640 host driver and update
Documentation/ide.txt accordingly.
* Make IDE_ARM config option visible so it can also be disabled if needed.
* Remove bogus comment from ide.c while at it.
v2:
* Fix two issues spotted by Sergei:
- replace ENOMEM error value by ENOENT in ide-h8300 host driver
- fix MODULE_PARM_DESC() in cmd640 host driver
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename init_hwif_data() to ide_init_port_data() and export it.
* For all users of ide_register_hw() with 'initializing' argument set
hwif->present and hwif->hold are always zero so convert these host
drivers to use ide_find_port()+ide_init_port_data()+ide_init_port_hw()
instead (also no need for init_hwif_default() call since the setup
done by it gets over-ridden by ide_init_port_hw() call).
* Drop 'initializing' argument from ide_register_hw().
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_init_port_hw() helper.
* rapide.c: convert rapide_locate_hwif() to rapide_setup_ports()
and use ide_init_port_hw().
* ide_platform.c: convert plat_ide_locate_hwif() to plat_ide_setup_ports()
and use ide_init_port_hw().
* sgiioc4.c: use ide_init_port_hw().
* pmac.c: add 'hw_regs_t *hw' argument to pmac_ide_setup_device(),
setup 'hw' in pmac_ide_{macio,pci}_attach() and use ide_init_port_hw()
in pmac_ide_setup_device().
This patch is a preparation for the future changes in the IDE probing code.
There should be no functionality changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix build break of powerpc holly_defconfig:
In file included from arch/powerpc/platforms/embedded6xx/holly.c:24:
include/linux/ide.h:1206: error: 'CONFIG_IDE_MAX_HWIFS' undeclared here (not in a function)
There's no need to have a sized array in the prototype, might as well
turn it into a pointer.
It could probably be argued that large parts of the include file can be
covered under #ifdef CONFIG_IDE, but that's a larger undertaking.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename ide_device_add() to ide_device_add_all() and make it accept
'u8 idx[MAX_HWIFS]' instead of 'u8 idx[4]' as an argument.
* Add ide_device_add() wrapper for ide_device_add_all().
* Convert ide_generic_init() to use ide_device_add_all().
* Remove no longer needed ideprobe_init().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Assign drive->quirk_list in ->quirkproc implementations:
- hpt366.c::hpt3xx_quirkproc()
- pdc202xx_new.c::pdcnew_quirkproc()
- pdc202xx_old.c::pdc202xx_quirkproc()
* Make ->quirkproc void.
* Move calling ->quirkproc from do_identify() to probe_hwif().
* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.
* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
no longer needed drive->present check from is_dev_seagate_sata().
* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
as an argument. Then convert ide_register_hw() to accept 'quirkproc'
argument instead of 'fixup' one.
* Remove no longer needed ->fixup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_dma_off_quietly() and __ide_dma_on() always available.
* Drop "__" prefix from __ide_dma_on().
* Check for presence of ->dma_host_on instead of ->ide_dma_on.
* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
to use ide_dma_on() and ide_dma_off_quietly() instead.
* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
from ide_hwif_t.
* Make ide_dma_on() void.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix SWDMA/MWDMA masks in cy82c693_chipset.
* Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to
check whether the DMA should be enabled even if ide_max_dma_mode()
fails.
* Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode()
and remove no longer needed cy82c693_ide_dma_on(). Then set
IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in
cy82c693_chipset.
* Bump driver version.
As a result of this patch cy82c693 driver will configure and use DMA on
all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In s390's spin_lock_irqsave, interrupts remain disabled while
spinning. In other architectures like x86 and powerpc, interrupts are
re-enabled while spinning if IRQ is not masked before spin_lock_irqsave
is called.
The following patch re-enables interrupts through local_irq_restore
while spinning for a lock acquisition.
This can improve system response.
[heiko.carstens@de.ibm.com: removed saving of pc]
Signed-off-by: Hisashi Hifumi <hifumi.hisashi@oss.ntt.co.jp>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds the s390 variant for smp_call_function_mask(). The
implementation is pretty straight forward using the wrapper
__smp_call_function_map() which already takes a cpumask_t argument.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove extern declaration of non-existent last_task_used_math and
remove unused field error_code from the thread_struct.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch fixes a problem with the following scenario:
1. Linux booted from DASD "A"
2. Reboot from DASD "B" using "/sys/firmware/reipl/ccw/device"
3. Reboot DASD "B"
Without this patch in step 3 on newer s390 systems under LPAR instead of
DASD "B", DASD "A" will be booted. The reason is that in step 2 we use CCW
reipl and in step 3 we use DIAG308 (subcode 3) reipl. DIAG308 does not
notice the CCW reipl and still thinks that it has to reboot DASD "A".
Before applying this fix, ensure to have MCF RJ9967101E or z9 GA3 base driver
installed.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of a kernel panic it is currently possible to specify that a dump
should be created, the system should be rebooted or stopped. Virtual sysfs
files under the directory /sys/firmware/ are used for that configuration.
In addition to that, there are kernel parameters 'vmhalt', 'vmpoff'
and 'vmpanic', which can be used to specify z/VM commands, which are
automatically executed in case of halt, power off or a kernel panic.
This patch combines both functionalities and allows to specify the z/VM CP
commands also via sysfs attributes. In addition to that, it enhances the
existing handling of shutdown triggers (e.g. halt or panic) and associated
shutdown actions (e.g. dump or reipl) and makes it more flexible.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It caused only a lot of confusion. From now on cpu hotplug of up to
NR_CPUS will work by default. If somebody wants to limit that then
the possible_cpus parameter can be used.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Used to contain the address of the holder of the lock. But since the
spinlock code is not inlined anymore all locks contain the same address
anyway. And since in addtition nobody complained about that for ages
its obviously unused. So remove it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the vmalloc area starts at a dynamic address depending on
the memory size. There was also an 8MB security hole after the
physical memory to catch out-of-bounds accesses.
We can simplify the code by putting the vmalloc area explicitely at
the top of the kernel mapping and setting the vmalloc size to a fixed
value of 128MB/128GB for 31bit/64bit systems. Part of the vmalloc
area will be used for the vmem_map. This leaves an area of 96MB/1GB
for normal vmalloc allocations.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The clear-by-asce operation of the idte instruction gets an asce
(address-space-control-element) as argument to specify which TLBs
need to get flushed. The current code passes a plain pointer to
the start of the pgd without the additional bits which would make
the pointer an asce. The current machines don't mind the difference
but a future model might want to use the designation type control
bits in the asce as a filter for the TLBs to flush.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a new interface so that cpus can be put into standby state and
configured state.
Only offline cpus can be put into standby state or configured state.
For that the new percpu sysfs attribute "configure" must be used.
To put a cpu in standby state a "0" must be written to the attribute.
In order to switch it into configured state a "1" must be written to
the attribute.
Only cpus in configured state can be brought online.
In addition this patch introduces a static mapping of physical to
logical cpus. As a result only the sysfs directories of present cpus
will be created. To scan for new cpus the new sysfs attribute "rescan"
must be used.
Writing to /sys/devices/system/cpu/rescan will trigger a rescan of
cpus and will create directories for new cpus.
On IPL only configured cpus will be used. And on reboot/shutdown all
cpus will remain in their current state (configured/standby).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
From: Cornelia Huck <cornelia.huck@de.ibm.com>
Change the adapter interrupt interface in order to allow multiple
adapter interrupt handlers to be registered. Indicators are now
allocated by cio instead of the device driver.
The qdio parts have been
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (67 commits)
fix drivers/ata/sata_fsl.c double-decl
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: Merge winbond support
ata_generic: Cenatek support
pata_winbond: error return
pata_serverworks: Fix cable types and cosmetics
pata_mpc52xx: remove un-needed assignment
libata: fix off-by-one in error categorization
ahci: factor out AHCI enabling and enable AHCI before reading CAP
ata_piix: implement SIDPR SCR access
ata_piix: convert to prepare - activate initialization
libata: factor out ata_pci_activate_sff_host() from ata_pci_one()
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: resychronize with upstream changes and resubmit
[libata] pata_legacy: typo fix
[libata] pata_winbond: update for new ->data_xfer hook
pata_pcmcia: convert to new data_xfer prototype
libata annotations and fixes
libata: use dev_driver_string() instead of "libata" in libata-sff.c
ata_piix: kill unused constants and flags
...
This allows others to use the DLM constants without being tied to the
function API of fs/dlm.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (81 commits)
RDMA/cxgb3: Fix the T3A workaround checks
IB/ipath: Remove unnecessary cast
IPoIB: Constify seq_operations function pointer tables
RDMA/cxgb3: Mark QP as privileged based on user capabilities
RDMA/cxgb3: Fix page shift calculation in build_phys_page_list()
RDMA/cxgb3: Flush the receive queue when closing
IB/ipath: Trivial simplification of ipath_make_ud_req()
IB/mthca: Update latest "native Arbel" firmware revision
IPoIB: Remove redundant check of netif_queue_stopped() in xmit handler
IB/ipath: Add mappings from HW register to PortInfo port physical state
IB/ipath: Changes to support PIO bandwidth check on IBA7220
IB/ipath: Minor cleanup of unused fields and chip-specific errors
IB/ipath: New sysfs entries to control 7220 features
IB/ipath: Add new chip-specific functions to older chips, consistent init
IB/ipath: Remove unused MDIO interface code
IB/ehca: Prevent RDMA-related connection failures on some eHCA2 hardware
IB/ehca: Add "port connection autodetect mode"
IB/ehca: Define array to store SMI/GSI QPs
IB/ehca: Remove CQ-QP-link before destroying QP in error path of create_qp()
IB/iser: Add change_queue_depth method
...
An IPoIB subnet on an IB fabric that spans multiple IB subnets can't
use link-local scope in multicast GIDs. The existing routines that
map IP/IPv6 multicast addresses into IB link-level addresses hard-code
the scope to link-local, and they also leave the partition key field
uninitialised. This patch adds a parameter (the link-level broadcast
address) to the mapping routines, allowing them to initialise both the
scope and the P_Key appropriately, and fixes up the call sites.
The next step will be to add a way to configure the scope for an IPoIB
interface.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is based on user feedback from Doug Ledford at RedHat:
Events that occur on an rdma_cm_id are reported to userspace through an
event channel. Connection request events are reported on the event
channel associated with the listen. When the connection is accepted, a
new rdma_cm_id is created and automatically uses the listen event
channel. This is suboptimal where the user only wants listen events on
that channel.
Additionally, it may be desirable to have events related to connection
establishment use a different event channel than those related to
already established connections.
Allow the user to migrate an rdma_cm_id between event channels. All
pending events associated with the rdma_cm_id are moved to the new event
channel.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To allow ULPs to tune timeout values and capture retry statistics,
report the number of times that a mad send operation was retried.
For RMPP mads, report the total number of times that the any portion
(send window) of the send operation was retried.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (509 commits)
V4L/DVB (7078): radio: fix sf16fmi section mismatch
V4L/DVB (7077): bt878: remove handcrafted PCI subsystem ID check
V4L/DVB (7075): Make a local function static
V4L/DVB (7074): DiB7000P: correct tuning problem for 7MHz channel
V4L/DVB (7073): DiB7070: Reception quality improved
V4L/DVB (7072): sets the MT2060 IF1 frequency according to EEPROM
V4L/DVB (7071): DiB0700: Start streaming the right way
V4L/DVB (7070): Fix some tuning problems
V4L/DVB (7069): Support for myTV.t
V4L/DVB (7068): Add support for WinTV Nova-T-CE driver
V4L/DVB (7067): fix autoserach in the Hauppauge NOVA-T 500
V4L/DVB (7066): ASUS My Cinema U3000 Mini DVBT Tuner
V4L/DVB (7065): Artec T14BR patches
V4L/DVB (7063): xc5000: Fix OOPS caused by missing firmware
V4L/DVB (7062): radio-si570x: Some fixes and new USB ID addition
V4L/DVB (7061): radio-si470x: Some cleanups
V4L/DVB (7060): em28xx: remove has_tuner
V4L/DVB (7059): cx88: Ensure the tuner is reset correctly
V4L/DVB (7058): IR corrections for the Pinnacle 800i
V4L/DVB (7056): tuner: suppress obsolete tuner i2c address warning for XC5000 tuners
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (67 commits)
ide: remove redundant DMA blacklist check from __ide_dma_on()
ide: cleanup ide_set_dma()
ide: remove redundant ->ide_dma_on call from set_using_dma()
sc1200: move DMA timings to timing tables
ide: add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag
sis5513: factor out UDMA programming code
pdc202xx_new: move PIO programming code to pdcnew_set_pio_mode()
ide: make 'extra' field in struct ide_port_info u8
ide: kill duplicate code in ide_dump_{ata,atapi}_status()
ide-disk: use ide_get_lba_addr()
ide: printk fix
ide: add ide_tf_read() helper
ide: fix registers loading order in ide_dump_ata_status()
ide-disk: use do_rw_taskfile() (take 2)
ide-disk: add ide_tf_set_cmd() helper
ide-disk: extend timeout for PIO-in commands
ide: remove 'handler' field from ide_task_t (take 2)
ide: use ->data_phase to set ->handler in do_rw_taskfile()
ide: convert do_rw_taskfile() to use ->data_phase
ide: merge flagged_taskfile() into do_rw_taskfile()
...
* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().
* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
(aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
methods in host drivers that don't (IDE core code guarantees that
->set_dma_mode will be called only for modes which are present
in SWDMA/MWDMA/UDMA masks).
While at it:
* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
hpt34x/hpt366/pdc202xx_old/serverworks host driver.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
