Presently this is special-cased for early initialization. While there are
situations where these static early initializations are still necessary,
with minor changes it is possible to use this for the regular ioremap
implementation as well. This allows us to kill off the special-casing for
the remap completely and to start tidying up all of the SH-5
special-casing in drivers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786 CPU subtype.
While this is a dual-core CPU, only UP is supported for now. L2 cache
support is likewise not yet implemented.
More information on this particular CPU subtype is available at:
http://www.renesas.com/fmwk.jsp?cnt=sh7786_root.jsp&fp=/products/mpumcu/superh_family/sh7780_series/sh7786_group/
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Modify the serial console code to wait for the transmit FIFO,
make sure all bits have been put on the wire before returning.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sci_poll_put_char() happens to also be used by the serial console,
while sci_poll_get_char() is only used by CONFIG_CONSOLE_POLL. Add
another gnarly ifdef to shut up the compiler.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Under qemu there is a race between the TDxE read-and-clear and the SCxTDR
write. While on hardware it can be gauranteed that the read-and-clear
will happen prior to the character being written out, no such assumption
can be made under emulation. As this path happens with IRQs off and the
hardware itself doesn't care about the ordering, move the SCxTDR write
until after the read-and-clear.
Signed-off-by: Vladimir Prus <vladimir@codesourcery.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7723 has SCIFA. This module is similer SCI register map, but it has FIFO.
So this patch adds new type(PORT_SCIFA) and change some type checking.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Correct the interrupt handler in sh4 serial device, return the correct
value and check for what is anabled in the SCSCR register. The sh7722 is
broken just sending a break using minicom.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
This was added at a time when the compiler did a less than stellar job of
optimizing out dead code. These days this tends to be less of a concern,
so kill it all off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is conditionalized on sh, and disabled for sh64.
Now that SH-5 ties in to the clock framework, the sh64 exception
can be dropped. Additionally, ARM will want to use the same hooks
once SH-Mobile G3 grows clock framework support, so switch these
paths over to HAVE_CLK now.
Once the H8 and ARM sh-sci users hook up HAVE_CLK, the driver can
be switched over to having an outright dependency on it and the
ifdefs can go away.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently we don't do much with UPF_IOREMAP other than special case it
for SH-5's onchip_remap() on the early console. Tie this in generically
for platforms that need the remap.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The below is the patch to replace blindly all possible places,
including Jack's fixes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
(Reviewed and checked rather than blindly added)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve sh7722 support for SCIF1 and SCIF2 and separate code
from sh7366 implementation.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable serial
platform drivers, to re-enable auto loading.
NOTE that Kconfig for some of these drivers doesn't allow modular builds, and
thus doesn't match the driver source's unload support. Presumably their
unload code is buggy and/or weakly tested...
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was an off-by-1 in the SCRFDR calculation that caused writes over
128-bytes to hang in the FIFO. Fix it up.
Signed-off-by: Yutaro Ebihara <ebiharaml@si-linux.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.
This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7366 cpu supports. Just the most basic things like interrupt
controller, clocks and serial port are included at this point.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The kgdb console code requires uart_set_options() and friends, which
are only provided by the serial core when console support is enabled.
These were sitting under CONFIG_SH_KGDB and resulted in a link error
when console support wasn't enabled, work that by rolling the console
routines under CONFIG_SH_KGDB_CONSOLE, which they should have been
all along.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7720 (SH3-DSP) CPU.
Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes old dead code:
- kill off sh7300 cpu support
- get rid of broken solution engine 7300 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds the enable/disable hooks for the port clock to sh-sci.
Signed-off-by: dmitry pervushin <dimka@nomadgs.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the GDB stub being entered via a special sysrq trigger,
we don't want to hit it directly from sci_br_interrupt().
Without this, there is access to the other sysrq triggers when
kgdb is enabled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7785-based Highlander board.
Some of the Highlander support code is reordered so that most of it
can be reused directly.
This also plugs in missing SH7785 checks in the places that need it,
as this is the first board to support the CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code has suffered quite a bit of bitrot, do some basic
tidying to get it to a reasonably functional state again.
This gets the basic support and the console working again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh-sci sci_br_interrupt() handler was failing to call
in to uart_handle_break(), which was something that only
the SH-3 path was doing, fix that up.
Additionally, SUPPORT_SYSRQ seems to have moved down too
far, move it back to the top so uart_handle_break() and
friends aren't no-ops.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This syncs up the SH clock framework with the linux/clk.h API,
for which there were only some minor changes required, namely
the clk_get() dev_id and subsequent callsites.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
