This board has a strange PCI SSID 13f6:ffff. Works as compabile as
MODEL_CMEDIA_REF.
Reported-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Configure the PEX8111 bridge on the PCI Express cards so that the audio
DMA controller can do proper burst reads and is less likely to lose
data. This is usually done automatically, but is required on older
cards where the user has not applied the PLX firmware update.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the PCIe/PCI bridge initialization code to configure only the
bridge that is actually connected to the sound chip, instead of any
bridge found in the system. The new code also makes it easier to add
other bridges.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The interrupt counter is independent of the buffer counter, so there are
no restrictions on the period size. Having fewer periods also makes
PulseAudio happy.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove duplicated include.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Platform driver ID table must be zero-element terminated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Be verbose and print out the device revision.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that all drivers that use SPI and I2C will work properly
by providing SPI write functions for all different I/O types.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The input monitor half volume bit results in a factor of 0.5, so the
minimum scale value should be -6 dB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename the symbol for the XCID pins, fix up a decimal/hex confusion for
the CMI8787 package ID, and add the other known package IDs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The anti-pop delay for the STX should be 800 ms, not 100 ms like the ST.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a PCI ID for the Xonar HDAV1.3 Slim. There is no actual support,
but the presence of the ID allows the EEPROM repair code to work for
this card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are more models without a CD input than with one, so handle this
explicitly with a device_config flag to avoid having to define a control
filter callback to filter it out.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The controller on the Xonar DS is labeled "AV66", not "AV200".
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add quirks for more devices (according to driver V.3.0.4-2).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since only 4 mainline ASoC codecs support the trigger
callback, we cannot rely upon them stopping the frame clock
if they are master and must assume it is running even if the
sound is paused. Thus we cannot start the ASP until the trigger
method.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Martin Ambrose <martin@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'fix/misc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: i2c/other/ak4xx-adda: Fix a compile warning with CONFIG_PROCFS=n
ALSA: prevent heap corruption in snd_ctl_new()
The PLL is disabled when the corresponding bit is set not the other
way around. This commit depends on my other commit with Subject
"ASoC: WM8804: Refactor set_pll code to avoid GCC warnings".
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that no uninitialised variable warnings are generated by
GCC.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure the DAI name does not include a '/' since we might have
per DAI debugfs or sysfs entries in the future.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
GPIO2 and GPIO3 on the WM8962 are MFPs and need to be put into GPIO mode
before the GPIO block can be used to control them. We're already doing
this when used via gpiolib, factor out the code for use when setting static
configurations via platform data as well.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow microphone detection on WM8962 to be performed using the interrupt
signal, allowing the detection of both microphone presence and button
presses with a signal singal from the CODEC to CPU. Currently a 250ms
debounce time is applied to both short circuit and presence detection,
this has not been optimised.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8962 features five GPIOs, add support for controlling their output
state via gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
While it is a generic serial port in practice the i.MX SSI is only supported
in Linux as an audio port (the i.MX has dedicated SPI controllers and so on).
This means we don't need to disambiguate against other uses of the hardware
and so can drop the -dai suffix from the driver name which fixes merge
issues with the i.MX tree in -next.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The restrictions on configuring BCLK are overly cautious, other constraints
in the system should ensure that reconfiguration is not possible when the
device is sufficiently active to be unable to support reclocking.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8804 is a high performance consumer mode S/PDIF transceiver with
support for 1 received channel and 1 transmitted channel.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No need to explicitly set the bus type, spi_register_driver does
that for us.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the widget for MICBIAS power control and allow configuration of the
microphone bias setup via the platform data for the WM8962. When
microphone status signals are brought out to GPIO this should be
sufficient to enable microphone detection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
There are some status bits for microphone detection in here.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
What was previously known as via_dmapos_patch, and hard-coded to be
used for VIA and ATI controllers, is now configurable through a module
option. The background is that some VIA controllers seem to prefer
via_dmapos_patch to be turned off.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide an initial hookup for interrupts on the WM8962. Currently we simply
report error status via log messages if an IRQ is provided for the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
When configuring the FLL we preserve the FLL enable configuration in order
to allow us to reenable the FLL after configuration but we do not clear
the other bits in the register, causing old configuration to be preserved.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Since we are using custom get/put handlers
use SOC_ENUM_SINGLE_EXT_DECL instead of the original SOC_ENUM_SINGLE_DECL
macro.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The snd_ctl_new() function in sound/core/control.c allocates space for a
snd_kcontrol struct by performing arithmetic operations on a
user-provided size without checking for integer overflow. If a user
provides a large enough size, an overflow will occur, the allocated
chunk will be too small, and a second user-influenced value will be
written repeatedly past the bounds of this chunk. This code is
reachable by unprivileged users who have permission to open
a /dev/snd/controlC* device (on many distros, this is group "audio") via
the SNDRV_CTL_IOCTL_ELEM_ADD and SNDRV_CTL_IOCTL_ELEM_REPLACE ioctls.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/soc/codecs/wm8985.c: In function 'wm8985_hw_params':
sound/soc/codecs/wm8985.c:731:2: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
Actually the variable is fine as int.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SNDRV_HDSP_IOCTL_GET_CONFIG_INFO and
SNDRV_HDSP_IOCTL_GET_CONFIG_INFO ioctls in hdspm.c and hdsp.c allow
unprivileged users to read uninitialized kernel stack memory, because
several fields of the hdsp{m}_config_info structs declared on the stack
are not altered or zeroed before being copied back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix bug in switching between dmic and mic when both use the same mux.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We are not using the private data in this function, so get rid of it.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove version number and clean up some indentation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Helps tracing errors further up the stack.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Could use dev_() but we'd have to remember the struct device somewhere
and it wouldn't make the logging clearer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Otherwise we try to re-register the CODEC device if the module is reloaded
and sysfs becomes miserable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
At least some of the systems using this device have multiple audio
subsystems so provide some guidance to userspace about which one this
is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The SPDIF in audio widget must be searched through the list as the widget
that contains the given pin as the connection source. The current code
was implemented in a reverse way.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to pass the register index and not the register value.
This patch depends on my previous patch "ASoC: Delegate to hw
specific read for volatile registers".
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that reads on volatile registers will correctly delegate
to the bus specific read function.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I've found the following patch is necessary to enable line-in on
my MacBookPro 5,3 machine. With the patch applied I've successfully
recorded audio from the line-in jack. This is based on the existing
5,5 support.
Signed-off-by: Vince Weaver <vweaver1@eecs.utk.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the SH DAC oss driver since there is an equivalent alsa driver.
oss has been deprecated for years. Furthermore this driver has BKL code
which we are trying to remove. Rather than attempt to fix this, simply
remove the driver.
Signed-off-by: John Kacur <jkacur@redhat.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The code can't really cope with I/O errors, so it would be better
to be consistent throughout all cache functions and return -1 instead
of -EINVAL.
The return value of snd_soc_read(...) is mostly checked in the probe
function and nowhere else.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure we stay within the cache boundaries when updating the
register cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On the HT-Omega Claro halo card, the ADC data must be captured from the
second I2S input. Using the default first input, which isn't connected
to anything, would result in silence.
Signed-off-by: Erik J. Staab <ejs@insightbb.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make sure we stay within the cache boundaries when updating the
register cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
rtd->dev.init_name is set twice in soc_probe_dai_link. I removed the first
assignement from dai_link->stream_name since then there won't be sysfs name
changes and usually dai_link->name seems to fit anyway better for a sysfs
directory name.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We've applied a fix-up for ALC269 VAIO only for two models. But all
Sony VAIO models with ALC269 codec seem to require the similar fix.
Let's apply it with vendor-id mask.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The headphone and external-mic pin NIDs can be null, and the jack input
elements should be skipped in such a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So machine drivers can see the declaration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Replace the explicit ifdef check and call of check_power_status ops with
a new helper function, hda_call_check_power_status().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Channel 2 and channel 3 were all wrongly mapped to HDMI slot 4.
This shows up as a bug that one channel is "lost" when playing in
surround41 mode.
Signed-off-by: Jerry Zhou <jerry.zhou@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DisplayPort works mostly in the same way as HDMI, except that it expects
a slightly different audio infoframe format.
Citations from "HDA036-A: Display Port Support and HDMI Miscellaneous
Corrections":
The HDMI specification defines a data island packet with a header of 4
bytes (3 bytes content + 1 byte ECC) and packet body of 32 bytes (28
bytes content and 4 bytes ECC). Display Port specification on the other
hand defines a data island packet (secondary data packet) with header of
4 bytes protected by 4 bytes of parity, and data of theoretically up to
1024 bytes with each 16 bytes chunk of data protected by 4 bytes of
parity. Note that the ECC or parity bytes are not present in the DIP
content populated by software and are hardware generated.
It tests DP connection based on the ELD conn_type field, which will be
set by the graphics driver and can be overriden manually by users
through the /proc/asound/card0/eld* interface.
The DP infoframe is tested OK on Intel SandyBridge/CougarPoint platform.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current FSI driver had data push/pop functions.
But the main operation of these 2 were very similar.
This mean it is possible to merge these to 1 function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current FSI driver is using
data-length / width / number / offset for variables.
But it was a very confusing name.
This patch rename them to easy to understand,
and add new functions for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Standardise on 'wm8978' as the name for the CODEC.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Now codec hits the SND_SOC_BIAS_OFF also when it is idle. This is also
the default state after probing and codec is left unconfigured and
unpowered by default. Initialization will happen when the bias state changes
and aic3x_set_power does power-up and cache sync.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is no need to reset the codec and perform cache sync if none of the
supply regulators were not disabled. Patch registers a notifier callback for
each supply and callback then sets a flag to indicate when cache sync is
required.
HW writes are also needless when codec bias is off so cache_only flag is set
independently of actual supply regulators state.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Now all the regulators are disabled when entering into SND_SOC_BIAS_OFF
and enabled when coming back to SND_SOC_BIAS_STANDBY state. Currently this
runtime control happens only with suspend/resume as this patch does not
change the default idle behavior.
This patch manages all the regulators and reset since it seems that register
sync is needed even if only analog supplies AVDD and DRVDD are disabled.
This was noted when the system was running with idle behavior changed and
IOVDD and DVDD were on.
It is not known are all the registers needed to sync or only some subset of
them. Therefore patch plays safe and does always full shutdown/power-up.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It will be easier to keep regulator enable/disable calls in sync when dynamic
regulator management is added if regulator management is moved from
aic3x_i2c_probe/_remove to aic3x_probe/_remove.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Create a helper function to simplify the code.
Also, cleaned up the ifdef SND_HDA_NEEDS_RESUME and
CONFIG_SND_HDA_POWER_SAVE. The former is always defined when the latter
is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC269vb and other variants don't use the widgets 0x24 but prefer the
widget 0x22 instead. We need to fix the input parser.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't call the COEF check for checking ACL269 codec variants at each
time in init but remember the type at the initialization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When quirks are applied, the numbers of output pins in autocfg aren't
set up properly but only pin arrays are changed. Let's fix it up so that
the rest of the parser can use autocfg.line_outs & co safely.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Purpose of this virtual Detection pin is to keep codec bias on whenever the
GPIO or jack detection features are needed.
Jack detection needs a mic bias so machine drivers can construct a following
route for instance for keeping the path and codec bias on:
"Input Jack" -> "Mic Bias xV" -> "Detection" -> detection block inside codec.
For the GPIO the machine driver can force the pin on with
snd_soc_dapm_force_enable_pin.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch merges all three patch_*hdmi variants to the single HDMI
parser. There is only one snd-hda-codec-hdmi module now.
In this patch, the behavior of each parser isn't changed much.
The old ATI parser still doesn't use the dynamic parser yet.
In later patches, they'll be cleaned up.
Also, this patch gets rid of the individual snd-hda-eld module and
builds into snd-hda-codec-hdmi, since this is referred only from the
HDMI parser.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes multiple bugs and a typo, occurred during the multi-
component transition.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The sh/siu ASoC driver doesn't compile because of a function defined static in
the source and extern in a header. Remove the unneeded declaration in the
header.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The clkdev API doesn't use .name and .id members of struct clk for clock
lookup. Instead clocks should be added to a lookup list. Without this patch
audio om the Migo-R board fails silently.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dzianis Kahanovich <mahatma@eu.by>
[Modified to move the location of the table]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The external mic jack for auto-mic switch must be really an external
jack and with a presense-detection capability. This patch makes the
check more paranoia.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the helper function to give the input-pin attribute for jack
connectivity and location. This simplifies checks of input-pin jacks
a bit in some places.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM proc files may open a race against substream close, which can
end up with an Oops. Use the open_mutex to protect for it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pm_qos_request isn't freed properly when OSS PCM emulation is used
because it skips snd_pcm_hw_free() call but directly releases the
stream. This resulted in Oops later.
Tested-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"uinfo->value.enumerated.item" is an unsigned int. If it's negative
when we do the comparison:
if ((int)uinfo->value.enumerated.item >= cval->max)
then we would read past the end of the array on the next line.
I also changed the strcpy() to strlcpy() out of paranoia.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Through the transition of autocfg to individual inputs array, I forgot
to rewrite the argument passed to alc_set_input_pin(). This resulted in
wrongly setup input pins. Fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
List registered platforms in debugfs to improve debugability of machine
drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow the user to inspect the list of registered DAIs at runtime to
improve diagnostics for machine driver setup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Help with diagnostics for machine driver setup by listing all the
registered CODECs in debugfs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
BugLink: http://launchpad.net/bugs/640254
In some cases a magic processing coefficient is needed to enable
the internal speaker on Dell M101z. According to Realtek, this
processing coefficient is only present on ALC269vb.
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When user want to change the card id to the same string
on the card via /sys/class/sound/cardX/id, do not
report error. Instead return with success without
doing anything.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Used only when CONFIG_SND_DEBUG=y
sound/usb/mixer.c: In function 'get_min_max':
sound/usb/mixer.c:762: warning: unused variable 'chip'
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most of Intel controllers work as generic HD-audio without quirks,
and it'll be hopefully so in future. Let's mark pci id with the
PCI_CLASS_MULTIMEDIA_HD_AUDIO for Intel so that the driver will work
with any new control chips in future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the preliminary support for new Conexant audio codecs with
14f1:5097, 14f1:5098, 14f1:50a1, 14f1:50a2, 14f1:50ab, 14f1:50ac,
14f1:50b8 and 14f1:50b9.
Unlike other Conexant parsers, this is designed to be mostly automatic,
parsing from BIOS pin configurations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For avoiding the click noises at power-saving, set some COEF values
for ALC269* codecs.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8985 is a low power, high quality, feature-rich stereo
CODEC designed for portable multimedia applications that
require low power consumption and high quality audio.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Complete the phasing out of aic3x_read_reg_cache, aic3x_write_reg_cache,
aic3x_read and aic3x_write calls.
This patch uses in aic3x_read the codec->hw_read that points to a function
implemented by soc-cache. Only use for aic3x_read is if wanting to read
volatile bits from those registers that has both read-only and read/write
bits. All other cases should use snd_soc_read.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Continue phasing out aic3x_read_reg_cache, aic3x_write_reg_cache, aic3x_read
and aic3x_write calls.
This patch takes the soc-cache in use and removes aic3x_read_reg_cache and
aic3x_write.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Start phasing out aic3x_read_reg_cache, aic3x_write_reg_cache, aic3x_read and
aic3x_write calls in order to switch to soc-cache helpers.
This patch replaces aic3x_read_reg_cache and aic3x_write with snd_soc_read
and snd_soc_write. This is basically null-op since .read and .write in
soc_codec_dev_aic3x points to aic3x_read_reg_cache and aic3x_write.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Like other coworkers, I'm about leave Mandriva/Edge-It so I'm changing
my mail address to use my personal one.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This assignment is done by the snd_soc_register_codec so there is no need
to redo it in probe function of a codec driver.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The usage of the BKL in the OSS sound drivers is
trivial, and each of them only locks against itself,
so it can be turned into per-driver mutexes.
This is the script that was used for the conversion:
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modifying an object twice without an intervening sequence point is
undefined.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Each of the two PCM controllers need to be registered during probe
with appropriate 'name' of the dai driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the SMDK64xx boards have two audio subsystems using the board
name as the card name by itself isn't so user friendly as it might
be.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add a quirk for laptop Toshiba Satellite C650D to have proper external HP and
external Mic support.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch modify FIFO_DIPSTICK value of PCM TX FIFO to be a optimal one.
Privious value (0x20) did not support 'Almost_full' of PCM FIFO for the DMA
request.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When PCM capture, sound recorded abnormally because of RX FIFO
threshold settings are missing. So, This patch modify PCM RX FIFO
setting codes same as TX.
And for DMA, if PCM RXFIFO_DIPSTICK is not '0', it doesn't effect
to DMA request, because DMA refer RX_FIFO_EMPTY flag as the DMA
request.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a simple off-by-one bug, the size of the register cache is
incorrectly set to the maximum register index. Fix it by adding one.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With this change it's not a error to call wl1273_set_audio_route
when the codec is active if the new routing value is the same
as the current active setting.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is only need to enable/disable once the PLL when the bias is going
between on, prepare, standby and off states.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The reg_cache_size is the number of elements in the register cache,
not the size of the cache itself. This is not a problem if the size
of each element of the cache is 1 byte but it matters in any other
case.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch solve below report from Guennadi.
But I didn't remove #include <sound/sh_fsi.h>.
Because it have FSI_PORT_B define which is used on this file.
> +#include <linux/platform_device.h>
> +#include <sound/sh_fsi.h>
> +#include <video/sh_mobile_hdmi.h>
Now that everything is done with strings - do you still need these
headers?
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PCM controller platform devices are registered by the
name 'samsung-pcm', so use the same in the CPU driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drop the invalid -dai suffix appended to the Samsung AC97 CPU DAI.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current SND_FSI_xxx menu attributes were bool,
but it should be tristate.
This patch solve below report from Guennadi
"bool" means, if someone is linking the whole ASoC into the kernel, they
will not be able to build this as a module. Not a big deal, but you're
stealing some freedom from the user.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the new Traktor Kontrol S4 by Native
Instruments. It features a new audio data streaming model, MIDI
in and out ports, a huge number of 174 dimmable LEDs, 96 buttons
and 46 absolute encoder axis, including some rotary encoders.
All features are supported by the driver now.
Did some code refactoring along the way.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the mic pins are assigned to the same location, we can omit the
redundant location prefix like "Front" or "Rear".
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch improves the input-source label strings to be generated from
the pin information instead of fixed strings per AUTO_PIN_* type.
This gives more suitable labels, especially for mic and line-in pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We can assign multiple pins to a single role now, let's reduce the
redundant FRONT_MIC and FRONT_LINE. Also, autocfg->input_pins[] is
no longer used, so this is removed as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Keep char array in the input_mux item itself instead of pointing to
an external string. This is a preliminary work for improving the
input-mux name based on the pin role.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update the Xonar config texts with the latest information about the
Xonar DS, HDAV1.3 Slim, and Xense.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the select directive does not handle indirect dependencies, select
those explicitly in the driver sections.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the possibility to route a mix of the two channels of stereo data to
the center and LFE outputs. Due to a WM8766 restriction, all surround
and back channels also get the mixed L/R signal in this case.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Automatically mute the speaker outputs as long as a headphone is plugged.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the polarity of the headphone detection pin is known, replace
the debugging message with a proper jack plug input device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the correct number, register bits, and names for the input switches.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The check for the volume update latch bit was accidentally in the wrong
function, where it would prevent the MSB from being written, instead of
correctly ignoring it for cached values.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By adding the subwoofer as a speaker pin, it is treated correctly when auto-muting.
BugLink: https://launchpad.net/bugs/611803
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If we pass in a device which is higher than SNDRV_RAWMIDI_DEVICES then
the "next device" should be -1. This function just returns device + 1.
But the main thing is that "device + 1" can lead to a (harmless) integer
overflow and that annoys static analysis tools.
[fix the case for device == SNDRV_RAWMIDI_DEVICE by tiwai]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a fixup table for ALC262 codec containing the entry for FSC
Celsius H270. Now both headphone jacks are detected properly as
headphones.
Reference: Novell bnc637263
https://bugzilla.novell.com/show_bug.cgi?id=637263
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the alc262 auto-parser to allow multiple pins
assigned for a single purpose (line-out, headphone or speaker).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently headphone auto-mute using alc_automute_pin() assumes only
the single pin used for the headphone output. Since there are devices
with multiple headphone jacks, we need to check all these pins there,
too.
Also this patch merges the common code between alc_automute_pin() and
alc_automute_amp() helper functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In snd_hda_parse_def_config(), some unused values may remain in hp_pins[]
array during the headphone-reassignment workaround. This patch clears
the unused array members.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_parse_pin_def_config() has some workaround for re-assigning
some pins declared as headphones to line-outs. This didn't work properly
for some cases because it used memmove() stupidly wrongly.
Reference: Novell bnc#637263
https://bugzilla.novell.com/show_bug.cgi?id=637263
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes sparse warning due non declaration of static function
sound/soc/omap/omap-mcbsp.c:783:5: warning: symbol 'omap_mcbsp_st_info_volsw' was not declared. Should it be static?
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Cc: alsa-devel@alsa-project.org
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Usage of 256 as clkdiv gives better rounding error (<1%)
for 16khz and 48khz
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The error handling in snd_seq_oss_open() has several bad codes that
do dereferecing released pointers and double-free of kmalloc'ed data.
The object dp is release in free_devinfo() that is called via
private_free callback. The rest shouldn't touch this object any more.
The patch changes delete_port() to call kfree() in any case, and gets
rid of unnecessary calls of destructors in snd_seq_oss_open().
Fixes CVE-2010-3080.
Reported-and-tested-by: Tavis Ormandy <taviso@cmpxchg8b.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver doesn't probe the device properly because of left-over cfg[]
that isn't used at all for msnd-classic device. This is only for msnd-
pinnacle.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
