It seems that Lenovo machines (or codec chip itself?) leave the unsol
event tags and the enablement-flag from other pins bogusly even on the
unused pins. Although this shouldn't be too critical, it's better to
clear them up sanely.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some codecs don't supply the mute amp-capabilities although the lowest
volume gives the mute. It'd be handy if the parser provides the mute
mixers in such a case.
This patch adds an extension amp-cap bit (which is used only in the
driver) to represent the min volume = mute state. Also modified the
amp cache code to support the fake mute feature when this bit is set
but the real mute bit is unset.
In addition, conexant cx5051 parser uses this new feature to implement
the missing mute controls.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42825
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A bug report with an old Sony laptop showed that we can't rely on BIOS
setting the pins of headphones but the driver should set always by
itself.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The docking-station of Thinkpad X200 & co supports also an SPDIF output,
and the corresponding pin 0x1c has to be enabled for using it.
Reported-and-tested-by: Sebastian Glita <sebastian.glita@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a new position_fix option value, 4, as a combo mode
to use LPIB for playbacks and POSBUF for captures. It's the way
recommended by Intel hardware guys.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enables port E of IDT 92HD91 codec as output and sets correct output
phase between ports E and D and high pass filter.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When there are multiple input sources, the driver wrongly overwrites with
the value of the last input source on other slots at resume. Thus the
primary input source may be shown wrongly.
Reported-and-tested-by: Julian Sikorski <belegdol@gmail.com>
Cc: <stable@kernel.org> [v3.1+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added sanity checks in a few places not to assume the pins having the
certain amp caps or the input-source being always assigned to a mux.
No actual bugs have been triggered by these, but surely better to be a
bit more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver may create duplicated mic boost controls when there are
multiple mics with the very same type / location, and this leads to
the error at actual kcontrol creation. It needs to check the validity
of the created control and add a proper index if it's duplicated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few clean-ups for post-static-quirk time:
- Call alc_auto_init_std() statically in alc_init() instead of setting
spec->init_hook in each caller. spec->init_hook field is left
unused for any future use.
- Move the call of set_capture_mixer() to to alc_parse_auto_config()
instead of each caller.
- Get rid of the ADC-filling and imux check in each parser function.
This is no longer needed since the auto-parser always check ADCs and
imux. It was only for the static quirks.
- Kill unused defines
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the machine has two speakers but wants to put more multi-io
jacks, the parser shouldn't consider about the shared DAC but try to
assign the individual DACs. Otherwise the channel mapping would be
fairly confused and lead to the wrong DACs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the multi-io is added to the two speaker output configuration,
the parser would try to add yet another "Bass Speaker" control since
it checks only cfg->line_outs. Add a workaround for it by simply
passing the channel name in the case of multi-io outputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Even if the outputs are using shared DACs, we can still create individual
mute siwtches since they are assigned per pin. This allows to create,
e.g. Speaker and Bass Speaker mute switches while the single volume is
used for these outputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When BIOS is damn crazy and gives no pin-config at all, the driver might
lead to a NULL dereference. Let's add a NULL check for such a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similarly in patch_via.c, parse the active analog-loopback connections
and create a list dynamically rather than static arrays.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Resitance is futile. The remaining static model quirks for Apple
machines with ALC882-compatible codecs are converted to the auto-parser
now. We can remove all alc*_quirks.c finally.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If anyone wants to debug the driver and avoid the existing fix-ups,
pass model=nofixup option. Then the driver will skip to pick up the
fixup list.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally the all static quirks for ALC880 are converted to the
auto-parser. Since we are never sure whether the BIOS on so many old
machines are really correct, the quirk table entries are copied as
they are, but just providing the proper pin-config values
accordingly.
Since alc880_quirks.c is removed, alc882_quirks.c has to be adjusted
slightly to be built again. There might be some compile warnings due
to the remaining alc882 quirks, but these shall be killed sooner or
later, I don't care it much at this point.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turned out that BIOS on most of ASUS mobo's set the pin-config tables
reasonably well for the auto-parser. We'd need GPIO setups, but should
work as is other than that.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS Z71V has a totally broken BIOS setup (at least the info I got),
thus we need to override the whole pin-config table to make the
auto-parser working correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The model=uniwill would work almost as is, but a couple of adjustments
are needed to make the mutli-io working correctly. The headphone and
speaker pins have to be marked properly in pin configs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Uniwill p53 has a sane BIOS setup but just needs the volume-knob handling
like Fujitsu laptops with ALC880.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar as the previous patch for model=fujitsu, we can now move the
static quirk for F1734 to the auto-parser. The only difference is the
default pin configurations: F1734 has less pins than Amilo's.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now adding the support for the volume-knob widget, we can move the static
quirk for ALC880 model=fujitsu to the auto-parser completely.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the call of alc_apply_fixup() with ALC_FIXUP_ACT_PROBE after the
whole setups of patch_ops & co, so that the fix-up function may override
the default setup. This will be needed for installing the own unsol
event handler (e.g. for volume-knob controls).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clevo machines with ALC880 are all well with proper BIOS setup.
It seems still requiring the additional COEF setup for the EAPD.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Refactor the DAC filling function to be used for both the primary
line outputs and extra outputs using the individual badness tables.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Medion W810 with ALC880 has a typical BIOS bug, copying the
pin-defaults without disabling the unused pins. At least, the pin
0x17 must be disabled. Also, it requires GPIO-2 setup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC880 model=lg could work fine with the auto-parser due to the recent
rewrite, but it still needs the manual adjustment; namely, the BIOS leaves
unused pins as some real active jacks. This confuses the parser.
Thus we just cover these pins and override the pin-configs as a fix-up.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Try harder to fit the multi-io pins also by checking the hard-wired
connections for multi-ios. Also, the badness values are adjusted to
prioritize the multi-ios as more valuable. These changes will enable
the multi-io on some machines without losing the current capability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous fix for the speaker on Acer Aspire 59135 introduced
another problem for surround outputs. It changed the connections on
the line-in/mic pins for limiting the routes, but it left the modified
connections. Thus wrong connection indices were written when set to
4ch or 6ch mode.
This patch fixes it by restoring the right connections just after
parsing the tree but before the initialization.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42740
Cc: <stable@kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the Realtek driver tires to assign the single-connected routes
for all pins only once at the beginning. However, since some DACs have
been already mapped, the rest pins might have also single conections.
In this patch, the driver does the single-connection assignment in a
loop until all possbile single-connections are checked. This will
improve the DAC assignment, e.g. for ASUS G72.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch improves the Realtek auto-parser for assigning the DACs and
mixers in more suitable ways by evaluating the assignment with "badness"
calculations.
When assigning a DAC hinders the assignment of individual DACs for
other pins, some badness point is given. Similarly, when it blocks the
assignment of unique mixer controls, another badness point is added.
Also, if no DAC, even shared DAC, can be assigned, more badness is
pointed. Finally, comparing the accumulated badness, the best route is
chosen among several trials.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the connections from the pin selector contain only two
widgets, a route to DAC and the aa-mixer, it's certainly a
single connection. In such a case, get_dac_if_single() should
return the connected DAC, too.
This will improve the detection of the individual DAC
assignment for each pin.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bitmap introduced in the commit [527e4d73: ALSA: hda/realtek - Fix
missing volume controls with ALC260] is too narrow for some codecs,
which may have more NIDs than 0x20, thus it may overflow the bitmap
array on them.
Just double the number to cover all and also add a sanity-check code
to be safer.
Cc: <stable@kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've enabled the static fixups for ASUS machines with ALC269 codec,
just for making things compatible during the transition to the auto-
parser. However, it seems that the static configurations do more harmful
than good, as some of entries don't match with the actual hardware setups.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we can clean up all static quirks for ALC260.
Also many codes in alc_quirks.c can be ripped off since they have been
used only by ALC260 static quirks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Presario B1900 needs a similar hack like Replacer, toggling GPIO1
per the jack state, in addition to the COEF setup used for other Acer
laptops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The support for Replacer 627V in the auto-parser needs the unique unsol
event handling: although the machine has a single output pin 0x0f, it's
used for both the headphone and the speaker, and the driver needs to
toggle the output route via GPIO 1.
In addition, it needs a special COEF setup with 0x3050.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
