Tell twl4030_madc_conversion that this driver needs raw values.
Driver twl4030_madc has some hardcoded values and conversation
functions which are incorrect for Nokia RX-51 board. This driver
rx51_battery expects raw values which convert itself.
This patch fixing values reported by power supply interface.
Before this patch driver reported always incorrect values on
3.8 kernel (sometimes design capacity was negative).
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There's no need to test whether a (delayed) work item is pending
before queueing, flushing or cancelling it. Most uses are unnecessary
and quite a few of them are buggy.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch updates the gas gauge constant for electric current
calculation according to hardware specification.
Signed-off-by: Benoit GAUTHIER <benoit.gauthier-xsig@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Tested-by: Benoit GAUTHIER <benoit.gauthier-xsig@stericsson.com>
To prevent overheating, provide differnt steps of charging current
interface to allow thermal mitigation. This will provide possibility
to reduce gradually the charging current.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When USB Dedicated or Standard host chargers are plugged into
the device, chargealg attempts to disable the PM2301 AC charger,
However, disabling PM2301 was failing because of it being in
runtime suepend mode & LPN pin being low.
Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Some of the comments in the ab8500 drivers reflect the behaviour
of the original device. As this driver now supports newer devices
then these comments are now redundant. Also some IRQ comments are
incorrect.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
Tested-by: Rabin VINCENT <rabin.vincent@stericsson.com>
The LED Indicator feature allows indicating through a led when the
PM2301 battery charging is active. SW shall not disable this LED.
Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
This patch restricts use of LPN pin to C2C boards to avoid
conflict on HSI for GPIO 60 use.
Signed-off-by: Benoit GAUTHIER <benoit.gauthier-xsig@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mustapha BEN-ZOUBEIR <mustapha.ben.zoubeir-xsig@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Tested-by: Benoit GAUTHIER <benoit.gauthier-xsig@stericsson.com>
deprecate some boilerplate code by using module_platform_driver
helper macro. No functional changes.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some of the headers and defines accrued over time are no longer
in use. Let's take the opportunity to remove a few of them.
Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Only AB8500 has this hardware bug, so these works only need to be run
there.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Martin SJOBLOM <martin.w.sjoblom@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
To optimize the current consumption we use pm_runtime autosuspend
functions which execute the pm_runtime_suspend after a delay of
inactivity on the other hand we use pm_runtime_resume every time
we receive an interruption to wake up the pm2301.
Signed-off-by: M BenZoubeir <mustapha.ben.zoubeir-xsig@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Signed-off-by: M BenZoubeir <mustapha.ben.zoubeir-xsig@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
When the state of USB Charge detection is changed then the calls
use a define for another register in other bank. This change
creates a new define for the correct register and removes the
magic numbers that are present.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Timers used for charging safety and maintenance must work even when
CPU power has collapsed. By using hrtimers with the realtime clock
the system is able to trigger an alarm that wakes-up the CPU and makes
it possible to handle events.
Allow a little slack time of 5 minutes for the hrtimers to allow CPU
to be woken-up in a more optimal power saving way. A 5 minute delay
to time-out timers relative to hours does not impact on safety.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Charging watchdog kicker work-thread gets started twice causing
'failed to kick watchdog' message after removing charger and
when re-inserting charger. This patch removes the superfluous
start of watchdog kicker-thread.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The newer AB's such as the AB8505, AB9540 etc include a
USBLink1 Status register which detects a larger range of
external devices. This should be used instead of the
USBLine Status register.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Yang QU <yang.qu@stericsson.com>
Provide AB8540 platform specific information required to run the
Battery Management subsystem on AB8540 based devices. For this to
happen we see the introduction of separate platform specific data
structures and a means in which to process them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Due to btemp filtering enabled during init, temp values reported
to charge algorithm driver started from 0. As a result,charge
algorithm was going into wrong state and charging was stopped.
Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Martin SJOBLOM <martin.w.sjoblom@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
AB8540 supports power path function in USB charging mode for fast
power up with dead and weak battery, and it could extend
the battery age.
When USB charging starts, if the Vbattrue is below than SW cut off
voltage, power path and pre-charge should be enabled. If Vbattrue
is higher than SW cut off voltage, power path and pre-charge should
be disabled. This is to make sure full current to battery charge.
At the end of charge, power path should be enable again to reduce
charging the battery again.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PM2301 Charger should always be available when using the AB8500
Battery Management system, we're ensuring this will be the case.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com>
The AB8505 does not have the same address for USB link-status
as has ab8500. Add AB8505_USB_LINK_STATUS and code to switch
to correct constant.
Signed-off-by: Hakan Berg <hakan.berg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
When battery capacity was going below 1% fg is not supposed
to report 0% unless we've got the LOW_BAT IRQ, no matter
what the FG-algorithm says. This made fg get stuck at 1% if
charger is connected when capacity is 1%.
Signed-off-by: Hakan BERG <hakan.berg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
Battery tempreature readings sometimes fail and results in
a value far from recent values. This patch adds a software
filter that disposes such readings, by allowing direct
updates on temperature only if two samples result in the
same temperature. Else only allow 1 degree change from previous
reported value in the direction of the new measurement.
Signed-off-by: Hakan Berg <hakan.berg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Martin SJOBLOM <martin.w.sjoblom@stericsson.com>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
When in suspend state, upon plug-in of external AC charger the
device needs to wake-up and charging operation started.
Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
This patch adds support for die temperature thermal protection
in pm2301 driver.
Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Do not set higher current in stepping functionality if VBUS is dropping.
After VBUS has dropped try to set current once again. If dropping again
then we have found the maximum capability of the charger.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mustapha Ben Zoubeir <mustapha.ben.zoubeir-nonst@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Tested-by: Olivier CLERGEAUD <olivier.clergeaud@stericsson.com>
Force main charger detect in turn on status.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Tested-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Added support for main charger over voltage protection.
Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Due to a bug in some AB8500 ASICs charger removal cannot always
be detected if the removal and reinsertion is done to close in time.
This patch detects above described case and handles the situation
so that charging will be kept turned on.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add 2.7v, 2.9v, 3.0v, 3.2v and 3.3v charging voltages for backup
battery. Before that only 2.5v, 2.6v, 2.8v, 3.1v were available.
Signed-off-by: Yang QU <yang.qu@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Maxime COQUELIN <maxime.coquelin@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Tested-by: Xiao Mei ZHANG <xiaomei.zhang@stericsson.com>
Unscaled capacity should be reported for POWER_SUPPLY_PROP_CAPACITY.
Signed-off-by: Martin Bergstrom <martin.bergstrom@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
Add support for a power cut feature which allows user to
configure when ab8505 and ab8540 based platforms should shut
down system due to low battery.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Any platform can be dynamically probed for model and version number
provided the AB8500 MFD parent device pointer is available. This
patch obtains that pointer and stores it in a locally controlled
struct for later use.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
End of charging is managed by SW.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big staging tree merge for 3.9-rc1
Lots of cleanups and updates for drivers all through the staging tree.
We are pretty much "code neutral" here, adding just about as many lines
as we removed.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEUEABECAAYFAlEmW7QACgkQMUfUDdst+ymlIACXT5mv8Y5A/KJa+QLTNNsofI8u
aACgq9hNZxJzX6VQMLXUV8+2SILOqYo=
=5wIj
-----END PGP SIGNATURE-----
Merge tag 'staging-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree update from Greg Kroah-Hartman:
"Here's the big staging tree merge for 3.9-rc1
Lots of cleanups and updates for drivers all through the staging tree.
We are pretty much "code neutral" here, adding just about as many
lines as we removed.
All of these have been in linux-next for a while."
* tag 'staging-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (804 commits)
staging: comedi: vmk80xx: wait for URBs to complete
staging: comedi: drivers: addi-data: hwdrv_apci3200.c: Add a missing semicolon
staging: et131x: Update TODO list
staging: et131x: Remove assignment of skb->dev
staging: wlan-ng: hfa384x.h: fix for error reported by smatch
staging/zache checkpatch ERROR: spaces prohibited around that
staging/ozwpan: Mark read only parameters and structs as const
staging/ozwpan: Remove empty and unused function oz_cdev_heartbeat
staging/ozwpan: Mark local functions as static (fix sparse warnings)
staging/ozwpan: Add missing header includes
staging/usbip: Mark local functions as static (fix sparse warnings)
staging/xgifb: Remove duplicated code in loops.
staging/xgifb: Consolidate return paths
staging/xgifb: Remove code without effect
staging/xgifb: Remove unnecessary casts
staging/xgifb: Consolidate if/else if with identical code branches
staging: vt6656: replaced custom TRUE definition with true
staging: vt6656: replaced custom FALSE definition with false
staging: vt6656: replace custom BOOL definition with bool
staging/rtl8187se: Mark functions as static to silence sparse
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
o goldfish_battery:
This is Android Emulator battery driver. Originally from Google, but
Intel folks reshaped it for mainline;
o pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses AB8500
battery management core;
o qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes;
o restart-poweroff:
A generic driver that implements 'power off by restarting'. The actual
poweroff functionality is implemented through a bootloader, so Linux'
task is just to restart the box. The driver is useful on Buffalo
Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked on
submitting the driver (as well as qnap-poweroff above).
- A lot of fixes for ab8500 drivers. This is a part of efforts of syncing
internal ST-Ericsson development tree with the mainline. Lee Jones @
Linaro worked on compilation and reshaping these series;
- New health properties for the power supplies: "Watchdog timer expire"
and "Safety timer expire";
- As usual, a bunch of fixes/cleanups here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=955B
-----END PGP SIGNATURE-----
Merge tag 'for-v3.9' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Four new drivers:
- goldfish_battery:
This is Android Emulator battery driver. Originally from Google,
but Intel folks reshaped it for mainline
- pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses
AB8500 battery management core
- qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes
- restart-poweroff:
A generic driver that implements 'power off by restarting'. The
actual poweroff functionality is implemented through a bootloader,
so Linux' task is just to restart the box. The driver is useful on
Buffalo Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked
on submitting the driver (as well as qnap-poweroff above).
Additionally:
- A lot of fixes for ab8500 drivers. This is a part of efforts of
syncing internal ST-Ericsson development tree with the mainline.
Lee Jones @ Linaro worked on compilation and reshaping these
series.
- New health properties for the power supplies: "Watchdog timer
expire" and "Safety timer expire"
- As usual, a bunch of fixes/cleanups here and there"
* tag 'for-v3.9' of git://git.infradead.org/battery-2.6: (81 commits)
bq2415x_charger: Add support for offline and 100mA mode
generic-adc-battery: Fix forever loop in gab_remove()
goldfish_battery: Add missing GENERIC_HARDIRQS dependency
da9030_battery: Include notifier.h
bq27x00_battery: Fix reporting battery temperature
power/reset: Remove newly introduced __dev* annotations
lp8727_charger: Small cleanup in naming
ab8500_btemp: Demote initcall sequence
ds2782_battery: Add power_supply_changed() calls for proper uevent support
power: Add battery driver for goldfish emulator
u8500-charger: Delay for USB enumeration
ab8500-bm: Remove individual [charger|btemp|fg|chargalg] pdata structures
ab8500-charger: Do not touch VBUSOVV bits
ab8500-fg: Use correct battery charge full design
pm2301: LPN mode control support
pm2301: Enable vbat low monitoring
ab8500-bm: Flush all work queues before suspending
ab8500-fg: Go to INIT_RECOVERY when charger removed
ab8500-charger: Add support for autopower on AB8505 and AB9540
abx500-chargalg: Add new sysfs interface to get current charge status
...
Fix up fairly straightforward conflicts in the ab8500 driver. But since
it seems to be ARM-specific, I can't even compile-test the result..
* Renamed mode BQ2415X_MODE_NONE to BQ2415X_MODE_OFF because this mode
turning chaging completly off
* Added new mode BQ2415X_MODE_NONE which enable charging with maximal
current limit 100mA (this is minimal safe value for bq2415x chips)
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
There is a forever loop calling iio_channel_release() because the
"chan < " part of the "chan < ARRAY_SIZE()" is missing. This is in both
the error handling on probe and also in the remove function.
The other thing is that it's possible for some of the elements of the
adc_bat->channel[chan] array to be an ERR_PTR(). I've changed them to be
NULL instead. We're still not allowed to pass NULLs to
iio_channel_release() so I've added a check.
Finally, I removed an unused "chan = ARRAY_SIZE(gab_chan_name);" statement
as a small cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Fix this link error on s390:
ERROR: "devm_request_threaded_irq" [drivers/power/goldfish_battery.ko] undefined!
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
randconfig complains about:
drivers/power/da9030_battery.c:113: error: field ‘nb’ has incomplete type
because there is no direct include for notifier.h which defines
struct notifier_block.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
All in-kernel users of class_find_device() don't really need mutable
data for match callback.
In two places (kernel/power/suspend_test.c, drivers/scsi/osd/osd_uld.c)
this patch changes match callbacks to use const search data.
The const is propagated to rtc_class_open() and power_supply_get_by_name()
parameters.
Note that there's a dev reference leak in suspend_test.c that's not
touched in this patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
