The ipr disk array devices do not support a cancel all
requests primitive, so change the ipr driver to never
send it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If an ipr adapter hits a fatal microcode error requiring a reset
while a SATA device is going through EH, it can result in a command
getting issued to the ipr adapter while it is getting reset, which
can cause PCI bus errors. Wait for any outstanding adapter reset
to finish prior to issuing a SATA device reset.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a timing issue related to nvram accesses in qla4xxx
driver for some cpu/slot speed combination.
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: "Patro, Sumant" <Sumant.Patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch provides the following:
1. adds support for the next version of Qlogic's iSCSI HBA, qla4032
(PCI Device ID 4032).
2. removes dead code related to topcat chip and renames
qla4010_soft_reset to qla4xxx_soft_reset (minor changes).
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On qla4xxx, the driver needs to grab the drvr semaphore provided by
the hardware, prior to issuing a reset. This patches takes care of a
couple of places where it was not being done. In addition there is
minor clean up.
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When the aic94xx driver creates ascbs, each ascb is initialized with a
timeout timer. If there are any ascbs left over when the driver is being
torn down, these timers need to be deleted. In particular, we seem to
hit this case when ascbs are issued yet never end up on the done list.
Right now there's a sequencer bug that results in this happening every
so often.
CONTROL PHY commands are typically sent when things are really messed
up with the sequencer; however, any other leftover ascb should produce
loud warnings.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch implements a REQ_DEVICE_RESET handler for the aic94xx
driver. Like the earlier REQ_TASK_ABORT patch, this patch defers the
device reset to the Scsi_Host's workqueue, which has the added benefit
of ensuring that the device reset does not happen at the same time
that the abort tmfs are being processed. After the phy reset, the
busted drive should go away and be re-detected later, which is indeed
what I've seen on both a x260 and a x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.
For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.
To make this work, an extra flag is introduced into the management side of the
work_struct. This governs auto-release of the structure upon execution.
Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function. This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated.. This is a
problem if the auxiliary data is taken away (as done by the last patch).
However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems. But then the work function must itself release the
work_struct by calling work_release().
In most cases, automatic release is fine, so this is the default. Special
initiators exist for the non-auto-release case (ending in _NAR).
Signed-Off-By: David Howells <dhowells@redhat.com>
ATAPI devices transfer fixed number of bytes for CDBs (12 or 16). Some
ATAPI devices choke when shorter CDB is used and the left bytes contain
garbage. Block SG_IO cleared left bytes but SCSI SG_IO didn't. This patch
makes SCSI SG_IO clear it and simplify CDB clearing in block SG_IO.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mathieu Fluhr <mfluhr@nero.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Douglas Gilbert <dougg@torque.net>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd and remove the trailing
whitespaces.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Resetting the adapter causes the ServeRAID driver to exceed the max time
allowed by the softlock watchdog. Resetting the hardware can easily require
30 or more seconds. To avoid the
"BUG: soft lockup detected on CPU#0!"
result, this patch adds a touch_nmi_watchdog() to the driver's MDELAY macro.
Cc: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes some needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
BusLogic: use kzalloc(), remove cast to/from void*
aic7xxx_old: fix typo in cast
NCR53c406a: ifdef out static built code
fd_mcs: ifdef out static built code
ncr53c8xx: ifdef out static built code
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Revert 15084a4a63 - it caused a
scheduling-inside-spinlock bug.
Cc: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Printk -> sdev_printk change originally from Luben Tuikov
<ltuikov@yahoo.com>. Loglevel changes prompted by Matthew Wilcox
<matthew@wil.cx>.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_assign_lock has been unused for a long time and is a bad idea
in general, so kill it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I wanted to add some BUG checks to scsi_prep_fn to make sure no one
sends us a non-sg command, but this function is a horrible mess.
So I decided to detangle the function and document what the valid
cases are. While doing that I found that REQ_TYPE_SPECIAL commands
aren't used by the SCSI layer anymore and we can get rid of the code
handling them.
The new structure of scsi_prep_fn is:
(1) check if we're allowed to send this command
(2) big switch on cmd_type. For the two valid types call into
a function to set the command up, else error
(3) code to handle error cases
Because FS and BLOCK_PC commands are handled entirely separate after
the patch this introduces a tiny amount of code duplication. This
improves readabiulity though and will help to avoid the bidi command
overhead for FS commands so it's a good thing.
I've tested this on both sata and mptsas.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_send_eh_cmnd is the last user of non-sg commands currently.
This patch switches it to a one-element SG list. Also updates the
kerneldoc comment for scsi_send_eh_cmnd to reflect reality while we're
at it.
Test on my mptsas card, but this should get testing with as many
drivers as possible.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch straightens out the code that distinguishes the various escb
opcodes in escb_tasklet_complete so that they can be handled correctly.
It also provides all the necessary code to create a workqueue item that
tells libsas to abort a sas_task.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds an external function, sas_abort_task, to enable LLDDs
to abort sas_tasks. It also adds a work_struct so that the actual
work of aborting a task can be shifted from tasklet context (in the
LLDD) onto the scsi_host's workqueue.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds an EH done queue to sas_ha, converts the error handling
strategy function and the sas_scsi_task_done functions in libsas to use
the scsi_eh_* commands for error'd commands, and adds checks for the
INITIATOR_ABORTED flag so that we do the right thing if a sas_task has
been aborted by the initiator.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a drive reports that no media is present, there's no point in
continuing to ask it about media status. This patch (as696) cuts the
TUR polling short as soon as the drive reports no media instead of
going a full 3 iterations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch (as810c) copies a minimum of 36 bytes of INQUIRY data, even if
the device claims that not all of them are valid. Often badly behaved
devices put plausible data in the Vendor, Product, and Revision strings but
set the Additional Length byte to a small value. Using potentially valid
data is certainly better than allocating a short buffer and then reading
beyond the end of it, which is what we do now.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an array overrun spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix uses of "&&" where "&" was obviously intended instead.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
XMSTATE_SOL_HDR could be set when the xmit thread tests it, but there may
not be anything on the r2tqueue yet. Move the XMSTATE_SOL_HDR set
before the addition to the queue to make sure that when we pull something
off it it is valid. This does not add locks around the xmstate test or make
that a atmoic_t because this is a fast path and if it is set when we test it
we can handle it there without the overhead. Later on we check the xmitqueue
for all requests with the session lock so we will not miss it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some messages from debug_scsi do not have trailing newlines,
making console messages difficult to read. Fix that.
Signed-off-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Unconditionally free crypto state, as it is always allocated during
TCP connection creation. Without this, crypto structures leak and
crc32c module refcounts grow as connections are created and
destroyed.
Signed-off-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For certain LLDs the sg driver can cause on oops
when the transfer length is large and not a
multiple of PAGE_SIZE.
ChangeLog:
- correct the length of the last scatter gather
list element.
- fix some printk()s that have the wrong function
name.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Updates the 3ware 9000 driver:
- Free irq handler in __twa_shutdown().
- Serialize reset code.
- Add support for 9650SE controllers.
Signed-off-by: Adam Radford <linuxraid@amcc.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Updating DDB0 inside aic94xx driver itself caused SMP command timeout. I
hit this SMP timeout problem twice but I am not able to reproduce it since
then. Here is a fix that retries an SMP command.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The patch updates DDB0 in the aic94xx driver itself. It doesn't supply
or use lldd_port_formed field. DDB0 is updated prior to posting
notification to libsas layer.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
SCSI_QLA_ISCSI needs to depend on NET to prevent build (link) failures
that are caused by selecting SCSI_ISCSI_ATTRS.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a cross-port of a similar patch for aic7xxx;
only it's a bit simpler here as we don't support HVD
and all controller actually implement this register.
I hope.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a cross-port from aic79xx; we still hit the occasional
BUG_ON in slave_destroy. And again we don't really need the
slave_destroy callback nor the ahc_linux_target structure
at all.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
aic79xx has a special 'iocell' chip which handles the precompensation.
If it's set via DV we should make sure to set the chip correctly, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Whenever an external device is resetted we really have to take
care to keep the channel in sync. Just notifying SCSI-ML and retry
is not enough as we have to make sure the SCSI bus is not getting
confused, either.
So whenever we detect an external reset we rewrite the command to
TUR, disable packetized command and notify the internal engine
that an abort has happened. This way we trigger a proper bus
reset sequence and all devices will be renegotiated properly.
Kudos to Justin Gibbs and Luben Tuikov for this idea.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix printk format warning:
drivers/scsi/lpfc/lpfc_attr.c:597: warning: long long unsigned int format, uint64_t arg (arg 4)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- make needlessly global code static
- #if 0 the following unused global functions:
- aic79xx_core.c: ahd_print_scb
- aic79xx_core.c: ahd_suspend
- aic79xx_core.c: ahd_resume
- aic79xx_core.c: ahd_dump_scbs
- aic79xx_osm.c: ahd_softc_comp
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleanups done to use min/max macros from kernel.h. Handcrafted MIN/MAX
macros are changed to use macros in kernel.h
[akpm@osdl.org: fix warning]
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for REPORT TARGET PORT GROUPS. This is used
eg for the multipathing priority callout to determine the path
priority.
With this patch multipath-tools can use the existing mpath_prio_alua
callout to exercise the path priority grouping.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix typo in check of return value of qla1280_bus_reset() which would
result in an adapter reset in addition to the bus reset.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
According to the iscsi RFC, we cannot send other requests if
we have sent a logout pdu. This patch enforces this requirement
by blocking the session and suspending the send thread. Userspace
decides if we restart the connection or if we just free everything.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have been dropping the pdu. We should just send it to userspace
and let it handle it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from bhalevy@gmail.com:
It looks like change 652 to libiscsi.c added some dead code around line
670
if (rc) {
spin_unlock_bh(&conn->session->lock);
goto again;
}
since 5 lines above we goto again if (rc).
It looks like the previous if (rc) should go away if we want to put the
ctask before
breaking out of the while loop with "goto again" (see following patch).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If connection creation fails we end up calling list_del
on a invalid struct. This then causes an oops. We are not
acutally using the lists (old MCS code we thought might
be useful elsewhere) so this patch just removes that
code.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The transport class recv mempools are causing slab corruption.
We could hack around netlink's lack of mempool support like dm,
but it is just too ulgy (dm's hack is ugly enough :) when you need
to support broadcast.
This patch removes the recv pools. We have not used them even when
we were allocting 20 MB per session and the system only had 64 MBs.
And we have no pools on the send side and have been ok there. When
Peter's work gets merged we can use that since the network guys
are in favor of that approach and are not going to add mempools
everywhere.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Doesn't make the hardware hot pluggable but does ensure the driver won't
crash when another device is hot-unplugged at the wrong moment. Soon I
propose to deprecate pci_find_device() and some of its friends.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Debugging TCQ issues has shown me this is a very useful parameter to be
able to view. Add it to he host class parameters.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It is known that 2 LSI Logic MegaRAID SATA RAID Controllers (150-4 and
150-6) don't support 64-bit DMA. Unfortunately currently this check is
wrong and driver sets 64-bit DMA mode for these devices.
Signed-off-by: Andrey Mirkin <amirkin@sw.ru>
Acked-by: "Ju, Seokmann" <Seokmann.Ju@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add PCI id. Plus correct for possibly missing resistor that can cause
FLASHEX to have the wrong value.
Signed-off-by: Sergey Kononenko <sergk@sergk.org.ua>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The "ibmvscsi: treat busy and error conditions separately" patch
submitted by Dave Boutcher back in June incorrectly reenables the CRQ.
The broken logic causes the adapter to get disabled if the CRQ
connection happens to close temporarily. This patch "fixes that
obviously wrong logic check" (Dave's words).
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: David Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Drop queue-depths across all luns for a given fcport
during TASK_SET_FULL statuses.
- Ramp-up I/Os after throttling.
- Consolidate completion-status handling of CS_QUEUE_FULL with
CS_COMPLETE as ISP24xx firmware no longer reports
CS_QUEUE_FULL.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Early ISP2432 parts have a known hardware issue when coming
out of a D3 hot state. This issue can result in a hung PCIe
link. Recent firmwares contain a workaround whereby the
stop-firmware mailbox command prevents the ISP from entering
the D3 hot state.
In order to ensure that the workaround succeeded the driver
must verify that the stop-firmware mailbox command completes
successfully. In the event of a failure, the driver
attempts a shutdown-retry after resetting the ISP and
re-executing firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete typedefd Scsi_Cmnd to struct scsi_cmnd in
the ninja scsi pcmcia driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in psi240i-driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If we fail to allocate mp->virt during the first while loop iteration,
mlist is still uninitialized, therefore we should check if before
dereferencing.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes a typo in the aic7xxx_old.c.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
According to the adaptec sources aic7xxx / aic79xx really can do
4MB transfers. So we should adjust .max_sectors.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is a dup printk at the tail of qla4xxx_module_init(). Remove the
first instance as it's before the complete success of the function.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
AM53C974A's Start Transfer Counter register has 24 bits, thus
maximum transfer length is 16MiB. But the maximum I can test
is 8MiB, so use that until somebody tests 16MiB.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Based on the original patch from Hannes Reinecke <hare@suse.de>
Fix st_open() to return -ENOMEDIUM instead of -EIO if no medium is
found.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change obsolete Scsi_Cmnd to struct scsi_cmnd in the Qlocic FAS408 driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change the obsolete Scsi_Cmnd to struct scsi_cmnd in the sun3-driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'ubuntu-updates' of master.kernel.org:/pub/scm/linux/kernel/git/bcollins/ubuntu-2.6:
[pci_ids] Add Quicknet XJ vendor/device ID's.
[valkyriefb] Ifdef for when CONFIG_NVRAM isn't enabled.
[platinumfb] Ifdef for when CONFIG_NVRAM isn't enabled.
[igafb] Add pci dev table for module auto loading.
[controlfb] Ifdef for when CONFIG_NVRAM isn't enabled.
[hid-core] TurboX Keyboard needs NOGET quirk.
[ixj] Add pci dev table for module auto loading.
[initio] Add pci dev table for module auto loading.
[fdomain] Add pci dev table for module auto loading.
[BusLogic] Add pci dev table for auto module loading.
[mv643xx] Add pci device table for auto module loading.
[alim7101] Add pci dev table for auto module loading.
It is known that 2 LSI Logic MegaRAID SATA RAID Controllers (150-4 and
150-6) don't support 64-bit DMA. Unfortunately currently this check is
wrong and driver sets 64-bit DMA mode for these devices.
Signed-off-by: Andrey Mirkin <amirkin@sw.ru>
Acked-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since it often takes around 20-30 seconds to scan a scsi bus, it's
highly advantageous to do this in parallel with other things. The bulk
of this patch is ensuring that devices don't change numbering, and that
all devices are discovered prior to trying to start init. For those
who build SCSI as modules, there's a new scsi_wait_scan module that will
ensure all bus scans are finished.
This patch only handles drivers which call scsi_scan_host. Fibre Channel,
SAS, SATA, USB and Firewire all need additional work.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In preparation for moving check_signature, change these users from asm/io.h
to linux/io.h
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/scsi/mesh.c:469: error: too many arguments to function 'mesh_interrupt'
drivers/scsi/mesh.c:507: error: too many arguments to function 'mesh_interrupt'
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Eliminate casts to/from void*
- Eliminate checks for conditions that never occur. These typically
fall into two classes:
1) Checking for 'dev_id == NULL', then it is never called with
NULL as an argument.
2) Checking for invalid irq number, when the only caller (the
system) guarantees the irq handler is called with the proper
'irq' number argument.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.infradead.org/~dhowells/irq-2.6:
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
IRQ: Typedef the IRQ handler function type
IRQ: Typedef the IRQ flow handler function type
commit 0181944fe6 adds a
'extended_error_logging' global variable to qla2xxx which is defined by
qla4xxx too.
Trying to build both drivers results in the following error:
LD drivers/scsi/built-in.o
drivers/scsi/qla4xxx/built-in.o: In function `qla4xxx_slave_configure':
drivers/scsi/qla4xxx/ql4_os.c:1433: multiple definition of `extended_error_logging'
drivers/scsi/qla2xxx/built-in.o:drivers/scsi/qla2xxx/qla_os.c:2166:
first defined here
make[2]: *** [drivers/scsi/built-in.o] Error 1
make[1]: *** [drivers/scsi] Error 2
make: *** [drivers] Error 2
The following patch simply adds a qla2_ (qla4_ respectively) prefix to
the variable name.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
- handle clear_user() error
- handle and properly unwind from sysfs errors thrown during mod init
- adjust order of calls in megasas_exit() to precisely match
registration order in megasas_init()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updated for extra attribute and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Handle and unwind from errors returned by driver model functions.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Notice and handle sysfs errors in module init, tape init
- Properly unwind errors in module init
- Remove bogus st_sysfs_class==NULL test, it is guaranteed !NULL at that point
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Properly handle and unwind errors in init_sd(). Fixes leaks on error,
if class_register() or scsi_register_driver() failed.
- Ensure that exit_sd() execution order is the perfect inverse of
initialization order.
FIXME: If some-but-not-all register_blkdev() calls fail, we wind up
calling unregister_blkdev() for block devices we did not register.
This was a pre-existing bug.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- check all sysfs-related return codes, and propagate them back to callers
- properly unwind errors in osst_probe(), init_osst(). This fixes a
leak that occured if scsi driver registration failed, and fixes an
oops if sysfs creation returned an error.
(unrelated)
- kzalloc() cleanup in new_tape_buf()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove the obsolete hosts.h file under drivers/scsi.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in aic7xxx_old.c.
Also replacing lots of whitespaces with tabs in structures and functions
which have been changed.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch sets timeout of max 180 seconds for ioctl completion.
It also updates the Changelog and hikes the version to 3.05.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds a tasklet for command completion.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds function to print the pending frame details before returning
failure from the reset routine. It also exposes a new variable megasas_dbg_lvl
that allows the user to set the debug level for logging.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds function pointer to invoke disable interrupt for
xscale and ppc IOP based controllers. Removes old implementation that checks
for controller type in megasas_disable_intr.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch removes duplicated code in frame calculation & adds
megasas_get_frame_count() that also takes into account the number of frames
that can be contained in the Main frame.
FW uses the frame count to pull sufficient number of frames from host memory.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch has the following enhancements :
a. handles new transition states of FW to support controller hotplug.
b. It reduces by 1 the maximum cmds that the driver may send to FW.
c. Sends "Stop Processing" cmd to FW before returning failure from reset routine
d. Adds print in megasas_transition routine
e. Sends "RESET" flag to FW to do a soft reset of controller
to move from Operational to Ready state.
f. Sending correct pointer (cmd->sense) to pci_pool_free
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Stall error handler if attempting recovery while an rport is
blocked. This avoids device offline scenarios due to errors in
the error handler.
Reference implementation from lpfc/mptfc.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The system hostname will be used during a subsequent FDMI registration
with the fabric.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Refactored original code from qla_gs.c:qla2x00_rsnn_nn().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iIDMA (Intelligent Interleaved Direct Memory Access) allows for
the HBA hardware to send FC frames at the rate at which they can
be received by a target device. By taking advantage of the
higher link rate, the HBA can maximize bandwidth utilization in a
heterogeneous multi-speed SAN.
Within a fabric topology, port speed detection is done via a Name
Server command (GFPN_ID) followed by a Fabric Management command
(GPSC). In an FCAL/N2N topology, port speed is based on the HBA
link-rate.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in the arm subdir
of the scsi-subsys.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Converts the obsolete Scsi_Cmnd to struct scsi_cmnd in the ips-driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Randy brought it to my attention that in proper english "can not" should always
be written "cannot". I donot see any reason to argue, even if I mightnot
understand why this rule exists. This patch fixes "can not" in several
Documentation files as well as three Kconfigs.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
following an email from John Adams <johna@onevista.com> to me with a patch
to enable tmscsim to use blocks up to 1MB and a discussion on linux-scsi,
below is a patch to enable clustering for tmscsim. I made it switchable
with a module parameter, with default "enable" - in case somebody gets
problems with it. Unfortunately, I was not able to check if this alone
lets you use any bigger blocks with a tape, as my tape seems to only
support 1 block size - only "mt setblk 1" is successful, any other value
fails. OTOH, testing on a P-133 showed that enabling clustering alone
improves throughput by 10% and reduces CPU load by another 10%, so, seems
a worthy thing to do. As for setting max_sectors, that might become a
separate patch...
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In some places, particularly drivers and __init code, the init utsns is the
appropriate one to use. This patch replaces those with a the init_utsname
helper.
Changes: Removed several uses of init_utsname(). Hope I picked all the
right ones in net/ipv4/ipconfig.c. These are now changed to
utsname() (the per-process namespace utsname) in the previous
patch (2/7)
[akpm@osdl.org: CIFS fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When SCSI-2 they can support luns past 7 and sparse luns.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is from RHEL4. I do not have any info from our bugzilla. All
I could find was something like this thread
http://lkml.org/lkml/2005/1/7/346
Report lun for linux does not work. It may be our lun format code or
it may be the device. It is probably not worth it to add anything
special for this device, so the patch just adds BLIST_NOREPORTLUN.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is from RHEL4. This box can support
scsi2 and can also support BLIST_SPARSELUN | BLIST_LARGELUN.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In scsi_execute_async()'s error path, a struct scsi_io_context
allocated with kmem_cache_alloc() is kfree()'d. Obviously
kmem_cache_free() should be used instead.
Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A new device (id 0x8650, nickname 'yosemite') support is added.
It's basically the same, except for following items:
- mapping of id and lun by firmware
- special handling for some commands in interrupt routine
- change of internal copy function for these special commands
- different reset handling code
- different shutdown notification command
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The payload_sz field in struct req_msg is not big enough to indicate
the size of req_msg, as its type is u8.
It is confirmed that this field is not used by firmware, so cancel
it here.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
this overrun was spotted by coverity (cid #1403).
If type == ARRAY_SIZE(scsi_device_types), we are off by one.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Comment says "Read high byte first as some registers increment..."
but code doesn't guarantee that, I think:
return ((ahd_inb(ahd, port+1) << 8) | ahd_inb(ahd, port));
Compiler can reorder it.
Make the order explicit.
Signed-off-by: Denis Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fixed rejections and added aic7xxx code
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
All on stack DECLARE_COMPLETIONs should be replaced by:
DECLARE_COMPLETION_ONSTACK
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch defines:
* a generic boolean-type, named 'bool'
* aliases to 0 and 1, named 'false' and 'true'
Removing colliding definitions of 'bool', 'false' and 'true'.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ->flags in struct request was split into two variables, in a recent
changeset. The merge of this change forgot to update SCSI's libsas,
probably because libsas was a very recent merge.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
After Christophs SCSI change, the only usage left is RQ_ACTIVE
and RQ_INACTIVE. The block layer sets RQ_INACTIVE right before freeing
the request, so any check for RQ_INACTIVE in a driver is a bug and
indicates use-after-free.
So kill/clean the remaining users, straight forward.
Signed-off-by: Jens Axboe <axboe@suse.de>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
Add modalias attribute support for the almost forgotten now EISA bus and
(at least some) EISA-aware modules.
The modalias entry looks like (for an 3c509 NIC):
eisa:sTCM5093
and the in-module alias like:
eisa:sTCM5093*
The patch moves struct eisa_device_id declaration from include/linux/eisa.h
to include/linux/mod_devicetable.h (so that the former now #includes the
latter), adds proper MODULE_DEVICE_TABLE(eisa, ...) statements for all
drivers with EISA IDs I found (some drivers already have that DEVICE_TABLE
declared), and adds recognision of __mod_eisa_device_table to
scripts/mod/file2alias.c so that proper modules.alias will be generated.
There's no support for /lib/modules/$kver/modules.eisamap, as it's not used
by any existing tools, and because with in-kernel modalias mechanism those
maps are obsolete anyway.
The rationale for this patch is:
a) to make EISA bus to act as other busses with modalias
support, to unify driver loading
b) to foget about EISA finally - with this patch, kernel
(who still supports EISA) will be the only one who knows
how to choose the necessary drivers for this bus ;)
[akpm@osdl.org: fix the kbuild bit]
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Acked-the-net-bits-by: Jeff Garzik <jeff@garzik.org>
Acked-the-tulip-bit-by: Valerie Henson <val_henson@linux.intel.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
gcc 4.1 with some extra warnings show the following:
drivers/scsi/ipr.c:6361: warning: comparison of unsigned expression < 0 is always false
drivers/scsi/ipr.c:6385: warning: comparison of unsigned expression < 0 is always false
drivers/scsi/ipr.c:6415: warning: comparison of unsigned expression < 0 is always false
The problem is that rc is of the type u32, which can never be smaller than
zero, therefore all three error handling checks get useless. This patch
changes it to a normal int, because all usages / all functions it get used
with expect an int.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Brian King <brking@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Converts pci_module_init() to pci_register_driver() in the scsi subsys on
23 drivers which only return the value of pci_module_init().
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
another signdness warning from gcc 4.1
drivers/scsi/osst.c:5154: warning: comparison of unsigned expression < 0 is always false
The problem is that blk is defined as unsigned, but all usages of it are
normal int cases. osst_get_frame_position() and osst_get_sector() return ints
and can return negative values. If blk stays an unsigned int, the error check
is useless.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Free seagate.h from obsolete drivers/scsi.h, remove a double inclusion od
linux/delay.h and remove the unneeded scsi/scsi_ioctl.h
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When testing on a Unisys machine it was discovered that the megaraid driver
would not initialize as it was requesting irq 162 instead of irq 1442 it
was assigned. The problem was the irq number had been truncated by being
stored in an unsigned char.
This patches fixes that problem and the driver now appears to work.
The ioctl interface appears fundamentally broken as it exports the irq
number to user space in an unsigned char.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/dc395x.c:1224: warning: format '%i' expects type 'int', but argument 5 has type 'size_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds support to attach SATA devices to ipr SAS adapters.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original patch from Ian Dall in bugzilla. Set command timeout as
specified by the SCSI layer rather than hardcode it to 30 seconds. I
have received a couple of reports of people hitting this one with
various tape configurations and the patch looks obviously correct.
- Jes
From http://bugzilla.kernel.org/show_bug.cgi?id=6275ian@beware.dropbear.id.au (Ian Dall):
The command sent to the card was using a 30second timeout regardless of the
timeout requested in the scsi command passed down from higher levels.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This sg driver patch addresses the problem with larger
page sizes reported by Brian King in this post:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115867718623631&w=2
Some other related matters are also addressed. Some of these
prevent oopses when the SG_SCATTER_SZ or scatter_elem_sz are
set to inappropriate values.
The scatter_elem_sz has been tested up to 4 MB which should
make the largest data transfer with one SCSI command, 32 MB
less one block, achievable with a relatively small number
of elements in the scatter gather list.
ChangeLog:
- add scatter_elem_sz boot time parameter and sysfs module
parameter that is initialized to SG_SCATTER_SZ
- the driver will then adjust scatter_elem_sz to be the
max(given(scatter_elem_sz), PAGE_SIZE)
It will also round it up, if necessary, to be a power
of two
- clean up sg.h header, correct bad urls and some statements
that are no longer valid
- make the def_reserved_size sysfs module attribute writable
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Small driver suspend() fixes in preparation for the PRETHAW events:
- Only compare message events for equality against PM_EVENT_* codes;
not against integers, or using greater/less-than comparisons.
(PM_EVENT_* should really become a __bitwise thing.)
- Explicitly test for SUSPEND events (rather than not-something-else)
before suspending devices.
- Removes more of the confusion between a pm_message_t (wraps event code)
and a "state" ... suspend() originally took a target system state.
These updates are correct and appropriate even without new PM_EVENT codes.
benh: "I think in the Mesh case, we should handle the freeze case as well or
we might get wild DMA."
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Greg KH <greg@kroah.com>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To whoever had written that code:
a) priority of >> is higher than that of &
b) priority of typecast is higher than that of any binary operator
c) learn the fscking C
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some user tools parse /proc/scsi/scsi, so we can't yet change the names.
Change the existing ones back to their old names, and add an admonition
to not make the same mistake that I did.
Andrew Morton reports that this was breaking YDL 4.1 userspace.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nlmsg_multicast now takes an extra allocation flag, so add it to
the use in the fibre channel transport class.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Key more of the domain validation settings off the inquiry data from
the disk (in particular, don't try IU or DT unless the disk claims to
support them.
Also add a new dv_in_progress flag to prevent recursive DV.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This started as a PCI reference fixup but to do that I need to build it,
to build it I need to fix it and its full of 32bitisms and uglies.
It has been resurrected, I'm not sure if this is a thank you for the
work on the license stuff or punishment for some unknown misdeed however
8). I've also fixed a memory scribble in the init code.
One oddity - the changes from HZ * to constants are deliberate. Whoever
originally wrote the code (or cleaned it up) used HZ for a cycle timing
loop even though is not HZ related. I've put it back to the counts used
in the old days when the driver was most used.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn:
Until the system is stabilized, I am suggesting the enclosed
modification to prevent the driver from tickling the panic. Once sysfs
and friends are stabilized, the patch may be backed out. We have yet to
evaluate if we really want to relinquish existing Scsi Devices in any
case, holding on to them as configuration of arrays comes and goes makes
some sense as well. As a result, we have opted to pull the lines rather
than comment them in legacy.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn:
The only real difference between the rkt and rx platform modules is the
offset of the message registers. This patch recognizes this similarity
and simplifies the driver to reduce it's code footprint and to improve
maintainability by reducing the code duplication.
Visibly, the 'rkt.c' portion of this patch looks more complicated than
it really is. View it as retaining the rkt-only specifics of the
interface.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn:
I am placing this functionality into an insmod parameter. Normally the physical
components are exported to sg, and are blocked from showing up in sd.
Note that the pass-through I/O path via the driver through the Firmware to the
physical disks is not an optimized path, the card is designed for Hardware
RAID, elevator sorting and caching. This should not be used as a means for
utilizing the aacraid based controllers as a generic scsi/SATA/SAS controller,
performance should suck by a few percentage points, any RAID meta-data on the
drives will confuse the controller about who owns the drives and there is a
high risk of destroying content in both directions. Unreliable and for
experimentation or strange controlled circumstances only.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn:
Basically cleanup, nothing here will have an affect. Adjusting some
error codes, removing superfluous definitions and code fragments.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some cards need to pause the sequencer before the SBLKCTL register is
touched. This fixes a PCI related oops seen on powerpc macs with this
card caused by trying to ascertain the bus signalling before beginning
domain validation.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For cards that don't support LVD, checking the SBLKCTL register to
determine the bus singalling doesn't work. So, check that the card
supports LVD first (AHC_ULTRA2) before checking the register.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
See http://www.torque.net/sg/sdebug26.html for more
information on the scsi_debug driver.
ChangeLog:
- add 'vpd_use_hostno' parameter to allow simulated hosts
to see the same set of targets (and luns). For testing
multipath software.
- add 'fake_rw' parameter to ignore the data in READ and
WRITE commands
- add support for log subpages (new in SPC-4)
- yield appropriate block descriptor for MODE SENSE
commands (only for pdt=0 (i.e. disks))
- REQUEST SENSE response no longer shows the stopped
power condition (SAT changed to agree with SPC-3)
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Check copy_to_user() return value in drivers/scsi/megaraid.c::megadev_ioctl()
This gets rid of this little warning:
drivers/scsi/megaraid.c:3661: warning: ignoring return value of 'copy_to_user', declared with attribute warn_unused_result
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "Ju, Seokmann" <Seokmann.Ju@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix this driver not to use a static two element host array instead use
a list. This should fix panic on multiple eject reinsert of the
pcmcia version of this device.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch removes the reliance on FLASH Manufacture IDs for validation.
Signed-off-by: Alexis Bruemmer <alexisb@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (64 commits)
[BLOCK] dm-crypt: trivial comment improvements
[CRYPTO] api: Deprecate crypto_digest_* and crypto_alg_available
[CRYPTO] padlock: Convert padlock-sha to use crypto_hash
[CRYPTO] users: Use crypto_comp and crypto_has_*
[CRYPTO] api: Add crypto_comp and crypto_has_*
[CRYPTO] users: Use crypto_hash interface instead of crypto_digest
[SCSI] iscsi: Use crypto_hash interface instead of crypto_digest
[CRYPTO] digest: Remove old HMAC implementation
[CRYPTO] doc: Update documentation for hash and me
[SCTP]: Use HMAC template and hash interface
[IPSEC]: Use HMAC template and hash interface
[CRYPTO] tcrypt: Use HMAC template and hash interface
[CRYPTO] hmac: Add crypto template implementation
[CRYPTO] digest: Added user API for new hash type
[CRYPTO] api: Mark parts of cipher interface as deprecated
[PATCH] scatterlist: Add const to sg_set_buf/sg_init_one pointer argument
[CRYPTO] drivers: Remove obsolete block cipher operations
[CRYPTO] users: Use block ciphers where applicable
[SUNRPC] GSS: Use block ciphers where applicable
[IPSEC] ESP: Use block ciphers where applicable
...
This patch converts ISCSI to use the new crypto_hash interface instead
of crypto_digest. It's a fairly straightforward substitution.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
0x848a in ID word 0 indicates CFA device iff the ID data is obtained from
IDENTIFY DEVICE. For ATAPI devices, 0x848a in ID work 0 indicates valid
ATAPI device. Fix sanity check in ata_dev_read_id() such that ATAPI
devices reporting 0x848a in ID word 0 is not handled as error.
The problem is identified by J.A. Magallon with HL-DT-ST DVDRAM GSA-4120B.
Signed-off-by: Tejun Helo <htejun@gmail.com>
Cc: J.A. Magallon <jamagallon@ono.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes obsolete typedef'd Scsi_Cmnd to struct scsi_cmnd.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
LD .tmp_vmlinux1
drivers/built-in.o(.text+0x8e1f9): In function `scsi_device_put':
drivers/scsi/scsi.c:887: undefined reference to `module_refcount'
make: *** [.tmp_vmlinux1] Error 1
There are only two users of module_refcount() outside of kernel/module.c
and the other one uses ifdef's similar to this.
Signed-Off-By: Daniel Walker <dwalker@mvista.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There are two changes here. The first reverses the broken PCI_DEVICE
conversion back to the old format. The second adds a missing PCI ID so
you can actually boot 2.6.18 on 2 month old VIA motherboards (right now
only 2.6.18-mm works).
CC'd to Jeff to check the PCI ident but its a) in several distro kernels
and b) in 2.6.18-mm [twice ??]
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Although the document says otherwise, some ich7m uses map 01b. This
patch adds separate map DB for ICH7M and adds map entry for 01b.
This was spotted on an ASUS laptop by Jonathan Dieter.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jonathan Dieter <jdieter@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a buglet; the errata check below this code is assuming the value in
the sstatus variable is what was pulled out of the SCR_STATUS register.
However, the status checks in the timeout loop clobber everything
but the first 4 bits of sstatus, so the errata checks are invalid.
This patch changes it to not clobber SStatus.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CONFIG_SCSI_NETLINK can become a bool since the item its
selecting (CONFIG_NET) cannot be a module.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch implements the ability to set the minimum and maximum
linkrates for both libsas (for expanders) and aic94xx (for the host
phys). It also tidies up the setting of the hardware min and max to
make sure they're updated when the expander emits a change broadcast.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
According to SPEC, the minimum_linkrate and maximum_linkrate should be
settable by the user. This patch introduces a callback that allows the
sas class to pass these settings on to the driver.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
At the moment we have two separate linkspeed enumerations covering
roughly the same values. This patch consolidates on a single one enum
sas_linkspeed in scsi_transport_sas.h and uses it everywhere in the
aic94xx driver. Eventually I'll get around to removing the duplicated
fields in asd_sas_phy and sas_phy ...
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The recent change to the way scsi_device_get()/put() work broke the
non modular build (we do a module_refcount on a NULL). Fix this by
checking for non-null before checking module_refcount().
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Spotted by: Dan Aloni <da-xx@monatomic.org>
The problem is there's inconsistent locking semantic usage of
scsi_alloc_target(). Two callers assume the target comes back with
reference unincremented and the third assumes its incremented. Fix by
always making the reference incremented on return. Also fix path in
target alloc that could consistently increment the parent lock.
Finally document scsi_alloc_target() so its callers know what the
expectations are.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for a new lpfc soft_wwpn sysfs attribute
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for new dev_loss_tmo callback
Goodness is that it removes code for a parallel nodev timer that
existed in the driver
Add support for the new fast_io_fail callback
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds the following functionality to the FC transport:
- dev_loss_tmo LLDD callback :
Called to essentially confirm the deletion of an rport. Thus, it is
called whenever the dev_loss_tmo fires, or when the rport is deleted
due to other circumstances (module unload, etc). It is expected that
the callback will initiate the termination of any outstanding i/o on
the rport.
- fast_io_fail_tmo and LLD callback:
There are some cases where it may take a long while to truly determine
device loss, but the system is in a multipathing configuration that if
the i/o was failed quickly (faster than dev_loss_tmo), it could be
redirected to a different path and completed sooner.
Many thanks to Mike Reed who cleaned up the initial RFC in support
of this post.
The original RFC is at:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115505981027246&w=2
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support to return adapter symbolic name (now that attribute is dynamic)
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support to post events via new FC event interfaces
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
During discussions with Mike Christie, I became convinced that we needed
a larger vendor id. This patch extends the id from 32 to 64 bits.
This applies on top of the prior patches that add SCSI transport events
via netlink.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch formally adds support for the posting of FC events via netlink.
It is a followup to the original RFC at:
http://marc.theaimsgroup.com/?l=linux-scsi&m=114530667923464&w=2
and the initial posting at:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115507374832500&w=2
The patch has been updated to optimize the send path, per the discussions
in the initial posting.
Per discussions at the Storage Summit and at OLS, we are to use netlink for
async events from transports. Also per discussions, to avoid a netlink
protocol per transport, I've create a single NETLINK_SCSITRANSPORT protocol,
which can then be used by all transports.
This patch:
- Creates new files scsi_netlink.c and scsi_netlink.h, which contains the
single and shared definitions for the SCSI Transport. It is tied into the
base SCSI subsystem intialization.
Contains a single interface routine, scsi_send_transport_event(), for a
transport to send an event (via multicast to a protocol specific group).
- Creates a new scsi_netlink_fc.h file, which contains the FC netlink event
messages
- Adds 3 new routines to the fc transport:
fc_get_event_number() - to get a FC event #
fc_host_post_event() - to send a simple FC event (32 bits of data)
fc_host_post_vendor_event() - to send a Vendor unique event, with
arbitrary amounts of data.
Note: the separation of event number allows for a LLD to send a standard
event, followed by vendor-specific data for the event.
Note: This patch assumes 2 prior fc transport patches have been installed:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115555807316329&w=2http://marc.theaimsgroup.com/?l=linux-scsi&m=115581614930261&w=2
Sorry - next time I'll do something like making these individual
patches of the same posting when I know they'll be posted closely
together.
Signed-off-by: James Smart <James.Smart@emulex.com>
Tidy up configuration not to make SCSI always select NET
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use block shared tags entirely within the driver. In the case of
shutdown, assume that there are no other outstanding commands, so tag
0 is fine.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add Promise SuperTrak 'stex' driver, supporting SuperTrak
EX8350/8300/16350/16300 controllers. The controller's firmware accepts
SCSI commands, handing them to the underlying RAID or JBOD disks.
The driver consisted of the following cleanups and fixes, beyond its
initial submission:
Ed Lin:
stex: cleanup and minor fixes
stex: add new device ids
stex: update internal copy code path
stex: add hard reset function
stex: adjust command timeout in slave_config routine
stex: use more efficient method for unload/shutdown flush
Jeff Garzik:
[SCSI] Add Promise SuperTrak 'shasta' driver.
Rename drivers/scsi/shasta.c to stex.c ("SuperTrak EX").
[SCSI] stex: update with community comments from 'Promise SuperTrak' thread
[SCSI] stex: Fix warning, trim trailing whitespace.
[SCSI] stex: remove last remnants of "shasta" project code name
[SCSI] stex: removed 6-byte command emulation
[SCSI] stex: minor cleanups
[SCSI] stex: minor fixes: irq flag, error return value
[SCSI] stex: use dma_alloc_coherent()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When accessing a device with disabled read access the capacity is set
randomly to 1GB. This makes it impossible to userspace tools to detect
invalid device capacities.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Acked-by: Chris Mason <mason@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In the normal IO path we should not be calling back
into the LLD since the LLD will have cleaned up the
task before or after calling complete pdu.
For the fail_command path we still need to do this
to force the cleanup.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the scsi eh sends a TUR and the session is down we could
return SCSI_ML_HOST_BUSY. scsi eh will ignore this and send
ask us to abort the command and we blindly accesst the
command ptr.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When a digest is spread across two network buffers, we currently
ignore this and try to check the digest with the partial buffer.
Or course this fails. This patch has use iscsi_tcp_copy to
copy the whole digest before testing it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The first burst length is only relevant if immedate data = Yes
or if Initial R2T is No
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When we relogin to a target, we have not yet negotiated digests
so we must reset the hdr_size var.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch built over the last ones fixes a bug in the partial header
resend code, where we add on another 4 bytes to the send length on the resend.
We want just the header plus digest.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We currently allocated seperate tfms for data and header digests. There
is no reason for this since we can never calculate a rx header and
digest at the same time. Same for sends. So this patch removes the data
tfms and has the send and recv sides use the rx_tfm or tx_tfm.
I also made the connection creation code preallocate the tfms because I
thought I hit a bug where I changed the digests settings during a
relogin but could not allocate the tfm and then we just failed.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iscsi_tcp calculates padding by using the expected transfer length. This
has the problem where if we have immediate data = no and initial R2T =
yes, and the transfer length ended up needing padding then we send:
1. header
2. padding which should have gone after data
3. data
Besides this bug, we also assume the target will always ask for nice
transfer lengths and the first burst length will always be a nice value.
As far as I can tell form the RFC this is not a requirement. It would be
silly to do this, but if someone did it we will end doing bad things.
Finally the last bug in that bit of code is in our handling of the
recalculation of data digests when we do not send a whole iscsi_buf in
one try. The bug here is that we call crypto_digest_final on a
iscsi_sendpage error, then when we send the rest of the iscsi_buf, we
doiscsi_data_digest_init and this causes the previous data digest to be
lost.
And to make matters worse, some of these bugs are replicated over and
over and over again for immediate data, solicited data and unsolicited
data. So the attached patch made over the iscsi git tree (see
kernel.org/git for details) which I updated today to include the patches
I said I merged, consolidates the sending of data, padding and digests
and calculation of data digests and fixes the above bugs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A couple targets like string bean and MDS, send r2ts with
a data len greater than the max burst we agreed to. We
were being strict in our enforcing of the iscsi rfc in that
code path, but there is no driver limitation that prevents
us from fullfilling the request. To allow those targets
to work we will ignore the max_burst length and send as
much data as the target asks for assuming it has consciously
decided to override its max burst length.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It is possible that a ctask could be completing and getting
cleaned up at the same time, we are finishing up the last
data transfer. This could then result in the data transfer
code using stale or invalid values. This patch adds a refcount
to the ctask. When the count goes to zero then we know the
transmit thread and recv thread or softirq are not touching
it and we can safely release it.
The eh should not need to grab a reference because it only cleans
up a task if it has both the xmit mutex and recv lock (or recv
side suspended).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iSCSI RFC states that the first burst length must be smaller than the
max burst length. We currently assume targets will be good, but that may
not be the case, so this patch adds a check.
This patch also moves the unsol data out offset to the lib so the LLDs
do not have to track it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sanitize the Vendor, Product, and Revision strings contained in an
INQUIRY result by setting all non-graphic or non-ASCII characters to ' '.
Since the standard disallows such characters, this will affect
only non-compliant devices.
To help maintain backward compatibility, NUL characters are treated
specially. They are taken as string terminators; they and all the
following characters are set to ' '. If some valid characters get
erased as a result... well, we weren't seeing them before so we haven't
lost anything.
The primary purpose of this change is to allow blacklist entries to
match devices with illegal Vendor or Product strings.
In addition, the patch updates a couple of function prototypes, giving
inq_result its correct type (unsigned char *).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The fix isn't actually in sd: it's in scsi_device_get(). I modified it
to allow devices to be returned in SDEV_CANCEL, but not SDEV_DEL. This
means that the device_remove_driver, which occurs in device_del() in
scsi_remove_device() after the device has gone into SDEV_CANCEL is now
effective at flushing the cache.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for sharing tag maps at the host level
(i.e. either every queue [LUN] has its own tag map or there's a single
one for the entire host). This formulation is primarily intended to
help single issue queue hardware, like the aic7xxx
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch sets can_queue in the aic94xx driver's scsi_host to better
performing values than what's there currently. It seems that
asd_ha->seq.can_queue reflects the number of requests that can be
queued per controller; so long as there's one scsi_host per
controller, it seems logical that the scsi_host ought to have the same
can_queue value. To the best of my (still limited) knowledge, this
method provides the correct value.
The effect of leaving this value set to 1 is terrible performance in
the case of either (a) certain Maxtor SAS drives flying solo or (b)
flooding several disks with I/O simultaneously (md-raid). There may be
more scenarios where we see similar problems that I haven't uncovered.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the end point of the separate aic94xx driver based on the
original driver and transport class from Luben Tuikov
<ltuikov@yahoo.com>
The log of the separate development is:
Alexis Bruemmer:
o aic94xx: fix hotplug/unplug for expanderless systems
o aic94xx: disable split completion timer/setting by default
o aic94xx: wide port off expander support
o aic94xx: remove various inline functions
o aic94xx: use bitops
o aic94xx: remove queue comment
o aic94xx: remove sas_common.c
o aic94xx: sas remove depot's
o aic94xx: use available list_for_each_entry_safe_reverse()
o aic94xx: sas header file merge
James Bottomley:
o aic94xx: fix TF_TMF_NO_CTX processing
o aic94xx: convert to request_firmware interface
o aic94xx: fix hotplug/unplug
o aic94xx: add link error counts to the expander phys
o aic94xx: add transport class phy reset capability
o aic94xx: remove local_attached flag
o Remove README
o Fixup Makefile variable for libsas rename
o Rename sas->libsas
o aic94xx: correct return code for sas_discover_event
o aic94xx: use parent backlink port
o aic94xx: remove channel abstraction
o aic94xx: fix routing algorithms
o aic94xx: add backlink port
o aic94xx: fix cascaded expander properties
o aic94xx: fix sleep under lock
o aic94xx: fix panic on module removal in complex topology
o aic94xx: make use of the new sas_port
o rename sas_port to asd_sas_port
o Fix for eh_strategy_handler move
o aic94xx: move entirely over to correct transport class formulation
o remove last vestages of sas_rphy_alloc()
o update for eh_timed_out move
o Preliminary expander support for aic94xx
o sas: remove event thread
o minor warning cleanups
o remove last vestiges of id mapping arrays
o Further updates
o Convert aic94xx over entirely to the transport class end device and
o update aic94xx/sas to use the new sas transport class end device
o [PATCH] aic94xx: attaching to the sas transport class
o Add missing completion removal from prior patch
o [PATCH] aic94xx: attaching to the sas transport class
o Build fixes from akpm
Jeff Garzik:
o [scsi aic94xx] Remove ->owner from PCI info table
Luben Tuikov:
o initial aic94xx driver
Mike Anderson:
o aic94xx: fix panic on module insertion
o aic94xx: stub out SATA_DEV case
o aic94xx: compile warning cleanups
o aic94xx: sas_alloc_task
o aic94xx: ref count update
o aic94xx nexus loss time value
o [PATCH] aic94xx: driver assertion in non-x86 BIOS env
Randy Dunlap:
o libsas: externs not needed
Robert Tarte:
o aic94xx: sequence patch - fixes SATA support
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This flag denotes local attachment of the phy. There are two problems
with it:
1) It's actually redundant ... you can get the same information simply
by seeing whether a host is the phys parent
2) we condition a lot of phy parameters on it on the false assumption
that we can only control local phys. I'm wiring up phy resets in the
aic94xx now, and it will be able to reset non-local phys as well.
I fixed 2) by moving the local check into the reset and stats function
of the mptsas, since that seems to be the only HBA that can't
(currently) control non-local phys.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
idescsi_pc_intr() uses local_irq_enable() in IRQ context: annotate it.
(this has no effect on kernels with lockdep disabled. On kernels with lockdep
enabled this means that we wont actually disable interrupts, and the warning
message will go away as well.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The callers of scsi_send_eh_cmnd are setting the cmnd buffer,
and then scsi_send_eh_cmnd is copying that updated buffer to
the old_cmnd variable. Then after the command runs, we end up
copying that old_cmnd var which has the new cmnd to the scsi
command buffer. When this command gets recent, all types of fun
things happen like getting TUR or START_STOP commands with
data and scatterlists.
This patch made against scsi-rc-fixes, has the callers of
scsi_send_eh_cmnd pass in the command so scsi_send_eh_cmnd
can do the right thing. This should go into 2.6.18 since this
fixes a regression added when we removed some of the scsi_cmnd
fields and replaced them with local variables.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Software must explicitely re-enable extended firmware tracing
after any ISP abort condition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code attempts to retry PLOGIs to fcports that are
FCP_TARGETs only. If the driver never performed a successful
PLOGI/PRLI, the port-type would never be assigned, and the
relogin logic would silently drop the request (and thus the port
would not be recognized and registered).
The fix is relatively straightforward, drop the FCP_TARGET-only
check.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a problem where sg is executing a ->nopage operation on a
compound page, it actually calls get_page() on the first page in the
compound rather than the page which is being mapped. The fix is to
select the correct page by indexing into the compound.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
vt6420 has super-fragile SCR registers which can hang the whole
machine if accessed with the wrong timings. This patch makes sata_via
use SCR registers only during probing and with the same timings as
before (pre new EH), which is proven to work.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
