The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 62469c76007e ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a6a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c76007e we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c76007e, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6b352ebccbcf ("net: ethernet: broadcom: bcmgenet:
use new api ethtool_{get|set}_link_ksettings").
We needs to revert the commit 62469c76007e ("net: ethernet: bcmgenet:
use phydev from struct net_device"), because this commit add a
regression. As the commit 6b352ebccbcf ("net: ethernet: broadcom:
bcmgenet: use new api ethtool_{get|set}_link_ksettings") depend
on the first one, we also need to revert it first.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 62469c76007e ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a6a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c76007e we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c76007e, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Nelson says:
====================
net: fec: updates to align IP header
This patch series is the outcome of investigation into very high
numbers of alignment faults on kernel 4.1.33 from the linux-fslc
tree:
https://github.com/freescale/linux-fslc/tree/4.1-1.0.x-imx
The first two patches remove support for the receive accelerator (RACC) from
the i.MX25 and i.MX27 SoCs which don't support the function.
The third patch enables hardware alignment of the ethernet packet payload
(and especially the IP header) to prevent alignment faults in the IP stack.
Testing on i.MX6UL on the 4.1.33 kernel showed that this patch removed
on the order of 70k alignment faults during a 100MiB transfer using
wget.
Testing on an i.MX6Q (SABRE Lite) board on net-next (4.8.0-rc7) showed
a much more modest improvement from 10's of faults, and it's not clear
why that's the case.
====================
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC receive accelerator (RACC) supports shifting the data payload of
received packets by 16-bits, which aligns the payload (IP header) on a
4-byte boundary, which is, if not required, at least strongly suggested
by the Linux networking layer.
Without this patch, a huge number of alignment faults will be taken by the
IP stack, as seen in /proc/cpu/alignment:
~/$ cat /proc/cpu/alignment
User: 0
System: 72645 (inet_gro_receive+0x104/0x27c)
Skipped: 0
Half: 0
Word: 0
DWord: 0
Multi: 72645
User faults: 3 (fixup+warn)
This patch was suggested by Andrew Lunn in this message to linux-netdev:
http://marc.info/?l=linux-arm-kernel&m=147465452108384&w=2
and adapted from a patch by Russell King from 2014:
http://git.arm.linux.org.uk/cgit/linux-arm.git/commit/?id=70d8a8a
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX27 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://cache.nxp.com/files/32bit/doc/ref_manual/MCIMX27RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX25 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://www.nxp.com/files/dsp/doc/ref_manual/IMX25RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prevent future potential pointer leaks when an unprivileged eBPF
program will read a pointer value from its context. Even if
is_valid_access() returns a pointer type, the eBPF verifier replace it
with UNKNOWN_VALUE. The register value that contains a kernel address is
then allowed to leak. Moreover, this fix allows unprivileged eBPF
programs to use functions with (legitimate) pointer arguments.
Not an issue currently since reg_type is only set for PTR_TO_PACKET or
PTR_TO_PACKET_END in XDP and TC programs that can only be loaded as
privileged. For now, the only unprivileged eBPF program allowed is for
socket filtering and all the types from its context are UNKNOWN_VALUE.
However, this fix is important for future unprivileged eBPF programs
which could use pointers in their context.
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
seccomp_phase1() does not exist anymore. Instead, update sample to use
__seccomp_filter(). While at it, set max locked memory to unlimited.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These samples fail to compile as 'struct flow_keys' conflicts with
definition in net/flow_dissector.h. Fix the same by renaming the
structure used in the sample.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation of joydev's input_device_id table recognizes only
devices with ABS_X, ABS_WHEEL or ABS_THROTTLE axes as joysticks.
There are joystick devices that do not have those axes, for example TRC
Rudder device. The device in question has ABS_Z, ABS_RX and ABS_RY axes
causing it not being detected as joystick.
This patch adds ABS_Z to the input_device_id list allowing devices with
ABS_Z axis to be detected correctly.
Signed-off-by: Ville Ranki <ville.ranki@iki.fi>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch avoids that the following memory leak is triggered if
use_blk_mq is disabled after a SCSI host has been allocated by the
ib_srp driver and before the same SCSI host is freed:
unreferenced object 0xffff8803a168c568 (size 256):
backtrace:
[<ffffffff81620c95>] kmemleak_alloc+0x45/0xa0
[<ffffffff811bb104>] __kmalloc_node+0x1e4/0x400
[<ffffffff81309fe4>] blk_mq_alloc_tag_set+0xb4/0x230
[<ffffffff814731b7>] scsi_mq_setup_tags+0xc7/0xd0
[<ffffffff81469c26>] scsi_add_host_with_dma+0x216/0x2d0
[<ffffffffa064bef5>] srp_create_target+0xe55/0x13d0 [ib_srp]
[<ffffffff8143ce23>] dev_attr_store+0x13/0x20
[<ffffffff8125f030>] sysfs_kf_write+0x40/0x50
[<ffffffff8125e397>] kernfs_fop_write+0x137/0x1c0
[<ffffffff811d8c13>] __vfs_write+0x23/0x140
[<ffffffff811d92e0>] vfs_write+0xb0/0x190
[<ffffffff811da5b4>] SyS_write+0x44/0xa0
[<ffffffff8162c8a5>] entry_SYSCALL_64_fastpath+0x18/0xa8
Fixes: 9aa9cc4221f5 ("scsi: remove the disable_blk_mq host flag")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we unshare a queue, the ADD_STA was not properly
initialised.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware has a new smart linker, and this table can now be
in ICCM or in SMEM. It is not hardcoded, but depends on code
size. Allow the full range.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This define should really be TX_CMD_SEC_KEY_FROM_TABLE
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW versions older than -17 for 3160 and 7260 and older than -22 for
newer NICs are not supported anymore. Don't load these versions
and remove code that handles them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
They seem to be there from the first day. We calculate these values but
never use them.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is called from get_station callback which means that every
time user space was getting/dumping station(s) we were leaking 2 KiB.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes: 1f0dc59a6de ("brcmfmac: rework .get_station() callback")
Cc: stable@vger.kernel.org # 4.2+
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As soon as debugging is turned on, the logs are filled with messages
reporting the interrupt status. As this quantity is usually zero, this
output is not needed. In fact, there will be a report if the status is
not zero, thus the debug line in question could probably be deleted.
Rather than taking that action, I have changed it to only be printed
when the newly added RTL8XXXU_DEBUG_INTERRUPT bit is set in the debug
mask.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This saves some 217, or about, derefences of priv->fops.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove last_tx_page argument from the llt_init() function. The
rtl8xxxu_fileops structure contains the correct TX_TOTAL_PAGE_NUM
value for the device, and rtl8xxxu_auto_llt_table() doesn't need to
know the value in the first place.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was detected tracing the 8188eu driver, but doesn't seem to make
any difference when using it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch helps get rid of goto statement and improves readability.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that in a corner case mwifiex_usb_tx_complete()
gets called before we exit from mwifiex_usb_host_to_card() after
submitting the urb. 'data_sent' flag remains set in this case. It
blocks further Tx packets and triggers watchdog timeout.
The problem is fixed by setting data_sent and port_block flag at
correct place.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Following crash issue is observed during TCP traffic stress
test
[ 2253.625439] NMI watchdog: BUG: soft lockup - CPU#3 stuck for 22s!
[kworker/u17:1:5191]
[ 2253.625520] Call Trace:
[ 2253.625527] [<ffffffffc0b47030>] ? moal_spin_lock+0x30/0x30
[usb8xxx]
[ 2253.625533] [<ffffffffc0ac3ceb>] ? wlan_wmm_lists_empty+0xb/0xf0
[mlan]
[ 2253.625537] [<ffffffffc0ab0ea3>] mlan_main_process+0x1b3/0x720
[mlan]
[ 2253.625540] [<ffffffffc0b337f5>] woal_main_work_queue+0x45/0x80
[usb8xxx]
[ 2253.625543] [<ffffffff8108aaf0>] process_one_work+0x150/0x3f0
[ 2253.625545] [<ffffffff8108b1e1>] worker_thread+0x121/0x520
[ 2253.625547] [<ffffffff8108b0c0>] ? rescuer_thread+0x330/0x330
[ 2253.625549] [<ffffffff81090222>] kthread+0xd2/0xf0
[ 2253.625551] [<ffffffff81090150>] ?
kthread_create_on_node+0x1c0/0x1c0
[ 2253.625553] [<ffffffff8179423c>] ret_from_fork+0x7c/0xb0
[ 2253.625555] [<ffffffff81090150>] ?
kthread_create_on_node+0x1c0/0x1c0
In mwifiex_usb_tx_complete(), we are updating port->block_status first
and then freeing the skb attached to that URB. We may end up attaching
new skb to URB in a corner case and same will be freed. This results in
the kernel crash. The problem is solved by changing the sequence.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 802.11 standard only has four valid auth type configurations of which
our firmware only supports two, ie. Open System and Shared Key. Simplify
the mapping falling back to automatic for other types specified by
user-space.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clearing the wowl wakeindicator happens with a rather odd
construction where the string "clear" is used to set the iovar
wowl_wakeind. This was implemented incorrectly as it caused an
out of bound access. Use an intermediate variable of correct
length and copy string in that. Problem was found using coverity.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When IPv6 address is to be cleared there is a possible out of
bound access. But also the clearing of the last entry and the
adjustment of total number of stored IPv6 addresses is not
updated. This patch fixes that bug. Bug was found using coverity.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
in the function brcmf_bus_start() in the exception handling a
check is made to dermine whether ifp is null, though this is not
possible. Removing the unnessary check.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As it turns out there is no need to use a worker for the callback
because it is not called from atomic context.
Reported-by: Dan Williams <dcbw@redhat.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of an error the variable returned is uninitialized. The caller
will probably check the error code before using it, but better assure
it is set to zero.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the error paths in brcmf_flowring_add_tdls_peer() the allocated
resource should be freed.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable info is assigned to point to bcdc->msg[1], which is the
same as pointing to bcdc->buf. As that is what we want to access
make it clear by fixing the assignment. This also avoid out-of-bounds
errors from static analyzers are bcdc->msg[1] is not in the structure
definition.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
802.11d is not always supported by firmware anymore. Currently the
AP configuration of 11d will cause an abort if the ioctl set is
failing. This behavior is not correct and the error should be
ignored.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Previously device used to start using IGTK key as Tx key as soon as it
gets downloaded in add_key(). This patch implements set_default_mgmt_key
handler. We will update Tx key ID in set_default_mgmt_key().
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the wl18xx specific config firmware we now have available.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Booting multiple wl12xx and wl18xx devices using the same rootfs is
a pain. You currently have to symlink the right nvs file depending
on the wl12xx type.
For example, with wl1271-nvs.bin being a symlink to wl127x-nvs.bin
by default and trying to bring up a wl128x based device:
wlcore: ERROR nvs size is not as expected: 1113 != 912
wlcore: ERROR NVS file is needed during boot
wlcore: ERROR NVS file is needed during boot
wlcore: ERROR firmware boot failed despite 3 retries
Note that wl18xx uses a separate config firmware wl18xx-conf.bin
that can be generated with tools using the following two git repos:
git.ti.com/wilink8-wlan/18xx-ti-utils
git.ti.com/wilink8-wlan/wl18xx_fw
So let's not configure the nvs file for wl18xx as it's not needed
AFAIK. If it turns out that we also need the nvs file for wl18xx,
we can just add it to the config firmware data for wl18xx.
Let's fix the issue by using the chip specific config firmware
data, and make sure we produce understandable warnings if something
is missing.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure the config firmware names and make it available
in platform data.
Let's also fix the order of the struct wilink_family_data
while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure the config firmware names and make it available
in platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move struct wilink_family_data to be available for all TI WLAN
variants. And fix familiy typo, it should be just family.
Looks like wl12xx use two different nvs.bin files and wl18xx
uses a different conf.bin file.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, we can have high order page allocations that specify
GFP_ATOMIC when configuring multicast MAC address filters.
For example, we have seen order 2 page allocation failures with
~500 multicast addresses configured.
Convert the allocation for the pending list to be done in PAGE_SIZE
increments.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Acked-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we can have high order page allocations that specify
GFP_ATOMIC when configuring multicast MAC address filters.
For example, we have seen order 2 page allocation failures with
~500 multicast addresses configured.
Convert the allocation for 'mcast_list' to be done in PAGE_SIZE
increments.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* added support for RRM by scan
* added support for packet injection
* migrate to devm memory allocation handling
* some fixes, mostly in DQA and new HW support
* other generic cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=42wP
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-09-19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* added support for MU-MIMO sniffer
* added support for RRM by scan
* added support for packet injection
* migrate to devm memory allocation handling
* some fixes, mostly in DQA and new HW support
* other generic cleanups
I stumbled over a new warning during randconfig testing,
with CONFIG_BPF_SYSCALL disabled:
drivers/net/ethernet/netronome/nfp/nfp_net_offload.c: In function 'nfp_net_bpf_offload':
drivers/net/ethernet/netronome/nfp/nfp_net_offload.c:263:3: error: '*((void *)&res+4)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/ethernet/netronome/nfp/nfp_net_offload.c:263:3: error: 'res.n_instr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
As far as I can tell, this is a false positive caused by the compiler
getting confused about a function that is partially inlined, but it's
easy to avoid while improving the code:
The nfp_bpf_jit() stub helper for that configuration is unusual as it
is defined in a header file but not marked 'static inline'. By moving
the compile-time check into the caller using the IS_ENABLED() macro,
we can remove that stub and simplify the nfp_net_bpf_offload_prepare()
function enough to unconfuse the compiler.
Fixes: 7533fdc0f77f ("nfp: bpf: add hardware bpf offload")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 1 warning when building kernel with W=1:
drivers/net/ethernet/broadcom/genet/bcmgenet.c:2763:5: warning: no previous prototype for 'bcmgenet_hfb_add_filter' [-Wmissing-prototypes]
In fact, this function is implemented in
drivers/net/ethernet/broadcom/genet/bcmgenet.c, but be called
by no one, thus can be removed.
So this patch removes the unused functions.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 10 warnings when building kernel with W=1:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:304:5: warning: no previous prototype for 'cxgb4_dcb_enabled' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:194:5: warning: no previous prototype for 'setup_sge_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:241:6: warning: no previous prototype for 'free_sge_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:268:5: warning: no previous prototype for 'cfg_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:344:6: warning: no previous prototype for 'free_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:353:5: warning: no previous prototype for 'request_msix_queue_irqs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:379:6: warning: no previous prototype for 'free_msix_queue_irqs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:393:6: warning: no previous prototype for 'name_msix_vecs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:433:6: warning: no previous prototype for 'enable_rx_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:442:6: warning: no previous prototype for 'quiesce_rx_uld' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 2 warnings when building kernel with W=1:
drivers/net/ethernet/marvell/mvneta.c:639:27: warning: no previous prototype for 'mvneta_get_stats64' [-Wmissing-prototypes]
drivers/net/ethernet/marvell/mvneta.c:3529:5: warning: no previous prototype for 'mvneta_ethtool_set_link_ksettings' [-Wmissing-prototypes]
In fact, these two functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
