The original device tree binding for this driver, from Viresh Kumar
unfortunately conflicted with the generic DMA binding, and did not allow
to completely seperate slave device configuration from the controller.
This is an attempt to replace it with an implementation of the generic
binding, but it is currently completely untested, because I do not have
any hardware with this particular controller.
The patch applies on top of the slave-dma tree, which contains both the base
support for the generic DMA binding, as well as the earlier attempt from
Viresh. Both of these are currently not merged upstream however.
This version incorporates feedback from Viresh Kumar, Andy Shevchenko
and Russell King.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the driver returns full length of the active descriptor which is
wrong. We have to go throught the active descriptor and substract the length of
each sent children in the chain from the total length along with the actual
data in the DMA channel registers.
The cyclic case is not handled by this patch due to len field in the descriptor
structure is left untouched by the original code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
By this new field we distinguish a total length of the chain and the individual
length of each descriptor in the chain.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The soft LLP mode is working for active descriptor only. So, we do not need to
have a copy of its pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently descriptors are allocated from normal cacheable memory and that slows
down filling the descriptors, as we need to call cache_coherency routines
afterwards. It would be better to allocate memory for these descriptors from
DMA_COHERENT memory. This would make code much cleaner too.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The same information could be extracted from the struct dma_chan.
The patch introduces helper function dwc_get_data_width() as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the direction value comes from the generic slave configuration
structure and explicitly as a preparation function parameter. The first one is
kinda obsoleted. Thus, we have to store the value passed to the preparation
function somewhere in our structures to be able to use it later. The best
candidate to provide the storage is a custom channel structure. Until now we
still keep and check the direction field of the slave config structure as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The to_dw_desc() macro helps to retrieve the dw_desc node from the
corresponding list_head structure.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
dw_dmac driver already supports device tree but it used to have its platform
data passed the non-DT way.
This patch does following changes:
- pass platform data via DT, non-DT way still takes precedence if both are used.
- create generic filter routine
- Earlier slave information was made available by slave specific filter routines
in chan->private field. Now, this information would be passed from within dmac
DT node. Slave drivers would now be required to pass bus_id (a string) as
parameter to this generic filter(), which would be compared against the slave
data passed from DT, by the generic filter routine.
- Update binding document
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Fixed __devinit usage]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The dw_dmac driver was originally developed for avr32 to be used with the
Synopsys DesignWare AHB DMA controller. Starting from 2.6.38, access to
the device's i/o memory was done with the little-endian readl/writel
functions(1)
This broke the driver for the avr32 platform, because it needs big
(native) endian accessors. This patch makes the endianness configurable
using 'DW_DMAC_BIG_ENDIAN_IO', which will default be true for AVR32
I submitted this patch before(2) but then waited for Andy to finish other
changes to the same module(3).
(1) https://patchwork.kernel.org/patch/608211
(2) https://lkml.org/lkml/2012/8/26/148
(3) https://lkml.org/lkml/2012/9/21/173
Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Havard Skinnemoen <havard@skinnemoen.net>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some controllers have the reduced functionality where the LLP multi block
transfers are not supported. This patch introduces a support of such
controllers. In case of memory copy or scatter-gather lists it emulates LLP
transfers via bunch of the regular single block ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Not all of the controllers support the 64 bit data width. Make it configurable
via platform data. The driver will try to get a value from the component
parameters, otherwise it will use the platform data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The maximum block size is a configurable parameter for the chip. So, driver
will try to get it from the encoded component parameters. Otherwise it will
come from the platform data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
There is a block of the registers that are optional. However, if enabled they
contain useful information about the controller hardware configuration. We will
use this piece of data to autoconfigure the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Use devm_kzalloc, devm_clk_get, devm_request_irq, and devm_request_and_ioremap
to reduce the code and to simplify the error path.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Use 'u32' for the LLI structure members, which are defined by hardware to be
32-bit. dma_addr_t is much more vague about its actual size.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Every DMA engine implementation declares a last completed dma cookie
in their private dma channel structures. This is pointless, and
forces driver specific code. Move this out into the common dma_chan
structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch adds support for DMA_SLAVE_CONFIG in dwc DMAC controller. Fields in
struct dw_dma_slave for passing similar data are preserved in this patch untill
all existing users are fixed.
That will be handled later in this patchset.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
In S2R all DMA registers are reset by hardware and thus they are required to be
reprogrammed. The channels which aren't reprogrammed are channel configuration
and interrupt enable registers, which are currently programmed at chan_alloc
time.
This patch creates another routine to initialize a channel. It will try to
initialize channel on every dwc_dostart() call. If channel is already
initialised then it simply returns, otherwise it configures registers.
This routine will also initialize registers on wakeup from S2R, as we mark
channels as uninitialized on suspend.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Nobody is currently maintaining dw_dmac. We are using dw_dmac for SPEAr13xx and
are currently maintaining it. After discussing with Vinod, sending this patch to
update maintainer-ship of dw_dmac.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some peripherals like amba-pl011 needs pause to be implemented in DMA controller
drivers. This also returns correct status from dwc_tx_status() in case chan is
paused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On ARMv7 cores, device memory mapped as Normal Non-cacheable, may not guarantee
ordered access causing failures in device drivers that do not use the mandatory
memory barriers. readl & writel versions contain necessary memory barriers for
this.
commit 79f64dbf68: "ARM: 6273/1: Add barriers to
the I/O accessors if ARM_DMA_MEM_BUFFERABLE" can be referred for more
information on this.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Msize or Burst Size is peripheral dependent in case of prep_slave_sg and
cyclic_prep transfers, and in case of memcpy transfers it is platform dependent.
So msize configuration must come from platform data.
Also some peripherals (ex: JPEG), need to be flow controller for dma transfers,
so this information in case of slave_sg & cyclic_prep transfers must come from
platform data.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In Synopsys designware, channel priority is programmable. This patch adds
support for passing channel priority through platform data. By default Ascending
channel priority will be followed, i.e. channel 0 will get highest priority and
channel 7 will get lowest.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Drop dw_dmac's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds a cyclic DMA interface to the DW DMA driver. This is
very useful if you want to use the DMA controller in combination with a
sound device which uses cyclic buffers.
Using a DMA channel for cyclic DMA will disable the possibility to use
it as a normal DMA engine until the user calls the cyclic free function
on the DMA channel. Also a cyclic DMA list can not be prepared if the
channel is already active.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The conversion of atmel-mci to dma_request_channel missed the
initialization of the channel dma_slave information. The filter_fn passed
to dma_request_channel is responsible for initializing the channel's
private data. This implementation has the additional benefit of enabling
a generic client-channel data passing mechanism.
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.
This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.
The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.
Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:
http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf
The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Changes since v4:
* Use client_count instead of dma_chan_is_in_use()
* Add missing include
* Unmap buffers unless client told us not to
Changes since v3:
* Update to latest DMA engine and DMA slave APIs
* Embed the hw descriptor into the sw descriptor
* Clean up and update MODULE_DESCRIPTION, copyright date, etc.
Changes since v2:
* Dequeue all pending transfers in terminate_all()
* Rename dw_dmac.h -> dw_dmac_regs.h
* Define and use controller-specific dma_slave data
* Fix up a few outdated comments
* Define hardware registers as structs (doesn't generate better
code, unfortunately, but it looks nicer.)
* Get number of channels from platform_data instead of hardcoding it
based on CONFIG_WHATEVER_CPU.
* Give slave clients exclusive access to the channel
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>,
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
