Commit 3800345f72 (pciehp: fix slot name)
introduces the pciehp_slot_with_bus module parameter, which was intended
to help work around broken firmware that assigns the same name to multiple
slots.
Commit 9e4f2e8d4d (pciehp: add message about
pciehp_slot_with_bus option) tells the user to use the above parameter
in the event of a name collision.
This approach is sub-optimal because it requires too much work from
the user.
Instead, let's rename the slot on behalf of the user. If firmware
assigns the name N to multiple slots, then:
The first registered slot is assigned N
The second registered slot is assigned N-1
The third registered slot is assigned N-2
The Mth registered slot becomes N-M
In the event we overflow the slot->name parameter, we report an
error to the user.
This is a temporary fix until the entire PCI core can be reworked
such that individual drivers no longer have to manage their own
slot names.
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit f46753c5e3 ("PCI: introduce pci_slot") removed the need for this error path. Eliminate this warning:
drivers/pci/hotplug/rpaphp_slot.c: In function 'rpaphp_register_slot':
drivers/pci/hotplug/rpaphp_slot.c:151: warning: label 'sysfs_fail' defined but not used
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Consolidate finding of a root bridge and getting its handle to the one
inline function. It's cut & pasted on multiple places. Use this new
inline in those.
Cc: kristen.c.accardi@intel.com
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
_OSC should be ran on a root bridge instead of the device itself. Do
this before touching OSHP since PCI fw specs states that _OSC should be
preferred over OSHP (however if the device has OSHP but not _OSC -- not
a root bridge -- it's not).
Cc: kristen.c.accardi@intel.com
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Export pci_pme_active() to drivers, so that they can clear the
PME_status bit and disable PME# for their devices without involving
ACPI.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Check the return value of device_create_bin_file in pci_create_bus and
unwind if necessary. Don't propagate error to caller, as failure to create
these files shouldn't prevent PCI from being initialised. Instead, just
log a warning.
Cc: Sven Wegener <sven.wegener@stealer.net>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
With the recent change to avoid masking MSIs using the MSI enable bit, devices
without an MSI mask bit will have their MSI capability always enabled when MSI
is in use, so we need to restore it regardless of the mask bit state.
Fixes kernel bz 11178.
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Libata has some hacks to deal with certain controllers going silly in D3
state. The right way to handle this is to keep a PCI device flag for
such devices. That can then be generalised for no ATA devices with power
problems.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A new option, pcie_aspm=force, will force ASPM to be enabled, even on system
with PCIe 1.0 devices.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Disable ASPM on pre-1.1 PCIe devices, as many of them don't implement it
correctly.
Tested-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ACPI FADT table includes an ASPM control bit. If the bit is set, do
not enable ASPM since it may indicate that the platform doesn't actually
support the feature.
Tested-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
David Vrabel has a device which generates an interrupt storm on the INTx
pin if we disable MSI interrupts altogether. Masking interrupts is only
a performance optimisation, so we can ignore the request to mask the
interrupt.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the kernel is configured to support 64-bit resources on a 32-bit
machine, we can support 64-bit BARs properly. Just change the condition
to check sizeof(resource_size_t) instead of BITS_PER_LONG.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Factor out the code to read one BAR from the loop in pci_read_bases into
a new function, __pci_read_base. The new code is slightly more
readable, better commented and removes the ifdef.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: fixup sparse endianness warnings in proc.c
PCI PM: make more PCI PM core functionality available to drivers
PCI/DMAR: don't assume presence of RMRRs
PCI hotplug: fix error path in pci_slot's register_slot
Make more PCI PM core functionality available to drivers
* Export pci_pme_capable() so that it can be called directly by
drivers (for example, tg3 needs that).
* Move the state choosing part of pci_prepare_to_sleep() to a
separate function, pci_target_state(), that can be called directly
by drivers (for example, tg3 needs that).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
RMRRs do not necessarily have to be present on all VT-d capable platforms.
The printk is just informational and does not need to be followed by an error
return.
Signed-off-by: Yong Y Wang <yong.y.wang@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: mark gross <mgross@linux.intel.com>
Cc: Keshavamurthy, Anil S <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Kobjects do not have a limit in name size since a while, so stop
pretending that they do.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix kernel-doc comments so that they don't produce errors.
Also cut some extraneous copy-paste text.
Error(linhead//drivers/pci/pci.c:1133): duplicate section name 'Description'
Error(linhead//drivers/pci/pci.c:1189): duplicate section name 'Description'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
Since the second argument of acpi_pci_choose_state() and
platform_pci_choose_state() is never used, remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Get rid of a superfluous acpi_pm_device_sleep_state() parameter. The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do. (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Proper memory barriers have been added to order accesses
to ->cmd_busy, so volatile declaration for cmd_busy can
be removed.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
drivers/pci/pci.c needs pm_wakeup.h since it uses device_set_wakup_capable().
The latter also needs to be stubbed out for !CONFIG_PM.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The recently introduced pci_prepare_to_sleep() needs the following fix,
because there are systems which are not power manageable by ACPI (ie.
ACPI doesn't provide methods to put the device into low power states and
back), but require ACPI hooks to be executed for wake-up to work.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
MSI and MSI-X support for interrupt remapping infrastructure.
MSI address register will be programmed with interrupt-remapping table
entry(IRTE) index and the IRTE will contain information about the vector,
cpu destination, etc.
For MSI-X, all the IRTE's will be consecutively allocated in the table,
and the address registers will contain the starting index to the block
and the data register will contain the subindex with in that block.
This also introduces a new irq_chip for cleaner irq migration (in the process
context as opposed to the current irq migration in the context of an interrupt.
interrupt-remapping infrastructure will help us achieve this).
As MSI is edge triggered, irq migration is a simple atomic update(of vector
and cpu destination) of IRTE and flushing the hardware cache.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IO-APIC support in the presence of interrupt-remapping infrastructure.
IO-APIC RTE will be programmed with interrupt-remapping table entry(IRTE)
index and the IRTE will contain information about the vector, cpu destination,
trigger mode etc, which traditionally was present in the IO-APIC RTE.
Introduce a new irq_chip for cleaner irq migration (in the process
context as opposed to the current irq migration in the context of an interrupt.
interrupt-remapping infrastructure will help us achieve this cleanly).
For edge triggered, irq migration is a simple atomic update(of vector
and cpu destination) of IRTE and flush the hardware cache.
For level triggered, we need to modify the io-apic RTE aswell with the update
vector information, along with modifying IRTE with vector and cpu destination.
So irq migration for level triggered is little bit more complex compared to
edge triggered migration. But the good news is, we use the same algorithm
for level triggered migration as we have today, only difference being,
we now initiate the irq migration from process context instead of the
interrupt context.
In future, when we do a directed EOI (combined with cpu EOI broadcast
suppression) to the IO-APIC, level triggered irq migration will also be
as simple as edge triggered migration and we can do the irq migration
with a simple atomic update to IO-APIC RTE.
TBD: some tests/changes needed in the presence of fixup_irqs() for
level triggered irq migration.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Interrupt-remapping enables queued invalidation. And once queued invalidation
is enabled, IOTLB invalidation also needs to use the queued invalidation
mechanism and the register based IOTLB invalidation doesn't work.
For now, Support for IOTLB invalidation using queued invalidation is
missing. Meanwhile, disable DMA-remapping, if Interrupt-remapping
support is detected.
For the meanwhile, if someone wants to really enable DMA-remapping, they
can use nox2apic, which will disable interrupt-remapping and as such
doesn't enable queued invalidation.
And given that none of the release platforms support intr-remapping yet,
we should be ok for this temporary hack.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Queued invalidation (part of Intel Virtualization Technology for
Directed I/O architecture) infrastructure.
This will be used for invalidating the interrupt entry cache in the
case of Interrupt-remapping and IOTLB invalidation in the case
of DMA-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Allocate the iommu during the parse of DMA remapping hardware
definition structures. And also, introduce routines for device
scope initialization which will be explicitly called during
dma-remapping initialization.
These will be used for enabling interrupt remapping separately from the
existing DMA-remapping enabling sequence.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Clean up the intel-iommu code related to deferred iommu flush logic. There is
no need to allocate all the iommu's as a sequential array.
This will be used later in the interrupt-remapping patch series to
allocate iommu much early and individually for each device remapping
hardware unit.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
code reorganization of the generic Intel vt-d parsing related routines and linux
iommu routines specific to Intel vt-d.
drivers/pci/dmar.c now contains the generic vt-d parsing related routines
drivers/pci/intel_iommu.c contains the iommu routines specific to vt-d
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
gart.h has only GART-specific stuff. Only GART code needs it. Other
IOMMU stuff should include iommu.h instead of gart.h.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
want to remove arch_get_ram_range, and use early_node_map instead.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the offset of PCI device's PM capability in its configuration space,
the mask of states that the device supports PME# from and the D1 and D2
support bits are cached in the corresponding struct pci_dev, the PCI
device PM code can be simplified quite a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce functions pci_prepare_to_sleep() and pci_back_from_sleep(),
to be used by the PCI drivers that want to place their devices into
the lowest power state appropiate for them (PCI_D3hot, if the device
is not supposed to wake up the system, or the deepest state from
which the wake-up is possible, otherwise) while the system is being
prepared to go into a sleeping state and to put them back into D0
during the subsequent transition to the working state.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* Introduce function acpi_pm_device_sleep_wake() for enabling and
disabling the system wake-up capability of devices that are power
manageable by ACPI.
* Introduce function acpi_bus_can_wakeup() allowing other (dependent)
subsystems to check if ACPI is able to enable the system wake-up
capability of given device.
* Introduce callback .sleep_wake() in struct pci_platform_pm_ops and
for the ACPI PCI 'driver' make it use acpi_pm_device_sleep_wake().
* Introduce callback .can_wakeup() in struct pci_platform_pm_ops and
for the ACPI 'driver' make it use acpi_bus_can_wakeup().
* Move the PME# handlig code out of pci_enable_wake() and split it
into two functions, pci_pme_capable() and pci_pme_active(),
allowing the caller to check if given device is capable of
generating PME# from given power state and to enable/disable the
device's PME# functionality, respectively.
* Modify pci_enable_wake() to use the new ACPI callbacks and the new
PME#-related functions.
* Drop the generic .platform_enable_wakeup() callback that is not
used any more.
* Introduce device_set_wakeup_capable() that will set the
power.can_wakeup flag of given device.
* Rework PCI device PM initialization so that, if given device is
capable of generating wake-up events, either natively through the
PME# mechanism, or with the help of the platform, its
power.can_wakeup flag is set and its power.should_wakeup flag is
unset as appropriate.
* Make ACPI set the power.can_wakeup flag for devices found to be
wake-up capable by it.
* Make the ACPI wake-up code enable/disable GPEs for devices that
have the wakeup.flags.prepared flag set (which means that their
wake-up power has been enabled).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rework pci_set_power_state() so that the platform callback is
invoked before the native mechanism, if necessary. Also, make
the function check if the device is power manageable by the
platform before invoking the platform callback.
This may matter if the device dependent on additional power
resources controlled by the platform is being put into D0, in which
case those power resources must be turned on before we attempt to
handle the device itself.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce function pointer platform_pci_power_manageable to be used
by the platform-related code to point to a function allowing us to
check if given device is power manageable by the platform.
Introduce acpi_pci_power_manageable() playing that role for ACPI.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It seems VT3336 can't do msi either as with its bro 3351. Disable it.
Reported in the following SUSE bug.
https://bugzilla.novell.com/show_bug.cgi?id=300001
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes pci_setup_device to handle pci_name() now returning a
constant string.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During the development of the physical PCI slot patch series, Gary Hade
kept on reporting strange oopses due to interactions between pci_slot
and acpiphp.
http://lkml.org/lkml/2007/11/28/319
find_root_bridges() unconditionally installs
handle_hotplug_event_bridge() as an ACPI_SYSTEM_NOTIFY handler for all
root bridges.
However, during module cleanup, remove_bridge() will only remove the
notify handler iff the root bridge had a hot-pluggable slot directly
underneath. That is:
root bridge -> hotplug slot
But, if the topology looks like either of the following:
root bridge -> non-hotplug slot
root bridge -> p2p bridge -> hotplug slot
Then we currently do not remove the notify handler from that root
bridge.
This can cause a kernel oops if we modprobe acpiphp later and it gets
loaded somewhere else in memory. If the root bridge then receives a
hotplug event, it will then attempt to call a stale, non-existent notify
handler and we blow up.
Much thanks goes to Gary Hade for his persistent debugging efforts.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the
VPD end tag will hang the device. This problem was initially
observed when a vpd entry was created in sysfs
('/sys/bus/pci/devices/<id>/vpd'). A read to this sysfs entry
will dump 32k of data. Reading a full 32k will cause an access
beyond the VPD end tag causing the device to hang. Once the device
is hung, the bnx2 driver will not be able to reset the device.
We believe that it is legal to read beyond the end tag and
therefore the solution is to limit the read/write length.
A majority of this patch is from Matthew Wilcox who gave code for
reworking the PCI vpd size information. A PCI quirk added for the
Broadcom NIC's to limit the read/write's.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some PCI devices will lock up if we attempt to read from VPD addresses
beyond some device-dependent limit. Until we can identify these
devices and adjust the file size accordingly, only let root read VPD
through sysfs to prevent a DoS by normal users.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make pci_setup_device() write the bus ID directly into the allotted storage,
rather than using pci_name() as the address as that now returns a const
pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp driver saves its private data pointer into pci_dev
structure using pci_set_drvdata()/pci_get_drvdata(). But because
pciehp is not a pci device driver but a PCI Express service driver, it
should save its private data pointer into pcie_device structure using
set_service_data()/get_service_data().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, pciehp driver enables command completed interrupt as follows.
(1) Don't enable at initialization.
(2) Enable command completed interrupt whenever pciehp issues a
command, if the command doesn't attempt to disable the interrupt.
(3) Disable command completed interrupt at driver unloading.
Once we enable command completed interrupt, we don't need to re-enable
it for every command. So we can simplify above steps as follows:
(1) Enable command completed interrupt at initialization.
(2) No special sequence for command completed interrupt.
(3) Disable command completed interrupt at driver unloading.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp driver's intialization sequence is as follows:
(1) initialize controller data structure
(2) install interrupt handler
(3) enable software notification
(4) initialize controller specific slot data structure
(5) initialize generic slot data structure and register it to pci hotplug core
The interrupt handler of pciehp assumes that controller specific slot
data structure is already initialized. However, it is installed at (2)
before initializing controller specific slot data structure at
(4). Because of this, pciehp driver cannot handle the following cases
properly.
- If devices that shares IRQ with pciehp raise interrupts between (2) and (4).
- If hotplug events (e.g. MRL open) happen between (3) and (4).
We already have a workaround for this problem ("pciehp: fix NULL
dereference in interrupt handler: dbd79aed1a).
But we still need fundamental fix.
This patch fix the problem by changing the initilization sequence as follows:
(1) initialize controller data structure
(2) initialize controller specific slot data structure
(3) install interrupt handler
(4) enable software notification
(5) initialize generic slot data structure and register it to pci hotplug core
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Convert printks to use dev_printk().
I converted pr_debug() to dev_dbg(). Both use KERN_DEBUG and are enabled
only when DEBUG is defined.
I converted printk(KERN_DEBUG) to dev_printk(KERN_DEBUG), not to dev_dbg(),
because dev_dbg() is only enabled when DEBUG is defined.
I converted DBG(KERN_INFO) (only in setup-bus.c) to dev_info(). The DBG()
name makes it sound like debug, but it's been enabled forever, so dev_info()
preserves the previous behavior.
I tried to make the resource assignment formats more consistent, e.g.,
"BAR %d: got res [%#llx-%#llx] bus [%#llx-%#llx] flags %#lx\n"
instead of sometimes using "start-end" and sometimes using "size@start".
I'm not attached to one or the other; I'd just like them consistent.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pcie_poll_cmd() and pcie_wait_cmd() are too large to be
inlined.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change command polling frequency to 100Hz from 10Hz in order to reduce
the delay in the common case of a command completing quickly.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup pcie_poll_cmd(): check the slot status once before entering our
completion test loop and convert the loop to a simpler while() block.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For the ranges with IORESOURCE_PREFETCH, export a new resource_wc interface in
pci /sysfs along with resource (which is uncached).
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the second argument of acpi_pci_choose_state() and
platform_pci_choose_state() is never used, remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Get rid of a superfluous acpi_pm_device_sleep_state() parameter. The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do. (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Detect all physical PCI slots as described by ACPI, and create entries in
/sys/bus/pci/slots/.
Not all physical slots are hotpluggable, and the acpiphp module does not
detect them. Now we know the physical PCI geography of our system, without
caring about hotplug.
[kaneshige.kenji@jp.fujitsu.com: export-kobject_rename-for-pci_hotplug_core]
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Greg KH <greg@kroah.com>
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix build with CONFIG_DMI=n]
Signed-off-by: Alex Chiang <achiang@hp.com>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, /sys/bus/pci/slots/ only exposes hotplug attributes when a
hotplug driver is loaded, but PCI slots have attributes such as address,
speed, width, etc. that are not related to hotplug at all.
Introduce pci_slot as the primary data structure and kobject model.
Hotplug attributes described in hotplug_slot become a secondary
structure associated with the pci_slot.
This patch only creates the infrastructure that allows the separation of
PCI slot attributes and hotplug attributes. In this patch, the PCI
hotplug core remains the only user of this infrastructure, and thus,
/sys/bus/pci/slots/ will still only become populated when a hotplug
driver is loaded.
A later patch in this series will add a second user of this new
infrastructure and demonstrate splitting the task of exposing pci_slot
attributes from hotplug_slot attributes.
- Make pci_slot the primary sysfs entity. hotplug_slot becomes a
subsidiary structure.
o pci_create_slot() creates and registers a slot with the PCI core
o pci_slot_add_hotplug() gives it hotplug capability
- Change the prototype of pci_hp_register() to take the bus and
slot number (on parent bus) as parameters.
- Remove all the ->get_address methods since this functionality is
now handled by pci_slot directly.
[achiang@hp.com: rpaphp-correctly-pci_hp_register-for-empty-pci-slots]
Tested-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: make headers_check happy]
[akpm@linux-foundation.org: nuther build fix]
[akpm@linux-foundation.org: fix typo in #include]
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Register one slot per slot, rather than one slot per function. Change the
name of the slot to fake%d instead of the pci address.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch unhides the SMBus on Compaq Deskpro EN
SFF P667 with the Intel 815E chipset. Unhiding it reveals
a THMC51 hardware monitoring chip.
Jean Delvare has checked that this machine has no ACPI
magic touching the SMBus nor the hardware monitoring chip,
so this should be safe.
The patch was tested on Fedora Core 9 with 2.6.25.4 kernel.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Rafał Haładuda <rh1985@wp.pl>
CC: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While refreshing my physical PCI slot series against upstream, I
noticed a few simple sparse/compile warnings that were easy to
fix.
Fix the following sparse warnings in PCIe:
drivers/pci/pcie/aer/aerdrv.c:86:6: warning: symbol 'pci_no_aer'
was not declared. Should it be static?
drivers/pci/pcie/portdrv_bus.c:21:17: warning: symbol
'pcie_port_bus_type' was not declared. Should it be static?
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
One more machine with a hidden Intel SMBus. Unhiding it reveals a SMSC
EMC6D100 hardware monitoring chip. I have checked that this machine
has no ACPI magic touching the SMBus nor the hardware monitoring chip,
so this should be safe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The destination of goto error also does a kfree(g_iommus), so it is not
correct to do one here.
This was found using Coccinelle (http://www.emn.fr/x-info/coccinelle/).
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fixup a typo in dbg_ctrl(); it was fetching SLOTSTATUS twice.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the following problems of shpchp driver about getting hotplug
control from firmware.
- The shpchp driver must not control the hotplug controller if it
fails to get control from the firmware. But current shpchp
controls the hotplug controller regardless the result, because it
doesn't check the return value of get_hp_hw_control_from_firmware().
- Current shpchp driver doesn't support _OSC.
The pciehp driver already have the code for evaluating _OSC and OSHP
and shpchp and pciehp can share it. So this patch move that code from
pciehp to acpi_pcihp.c.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since we need to wait for command completion for muximum 1sec, waiting
command should not be interrupted by a signal.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp evaluates _OSC/OSHP method after some controller
initialization is done. So if evaluating _OSC/OSHP is failed, we need
to cleanup already initialized data structures or hardware. This
clearly is not robust way. With this patch, _OSC/OSHP evaluation is
done first.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the redundant initialization of pci_dev member of struct
controller in pciehp_probe(). It is initialized in pcie_init().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Implement new suspend and hibernation callbacks for the PCI bus type.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The position of MSI capability is already cached in the msi_desc when
we enter the msi_set_mask_bits(). Use it instead.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The 'retval' variable in __pci_osc_support_set() is no longer
used. Remove this unused variable.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pci-acpi implementation checks osc_data->support_stat to see
if control bits had been already queried. It is not good from the
viewpoint of easy understanding. So this patch adds new 'is_queried'
flag to indicate query had been done.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pci-acpi implementation uses array in osc_data directly to
evaluate _OSC. It needs to save the old data and restore it if _OSC
evaluation fails. To make it more robust, we should use local array to
evaluate _OSC.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the duplicated code in acpi_query_osc() and acpi_run_osc().
It simplifies the code very much.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If a device supports #PME and can generate PME events from D0, we may see
superfluous events before a driver is loaded (drivers should only enable PME as
needed), preventing suspend from working if the corresponding GPE was enabled.
Likewise, if the ACPI device has the _PRW object, the _PSW/_DSW object will be
called in order to disable the wakeup functionality. But when it is allowed to
wake up the sleeping state, OSPM will enable it again.
So we should disable PME in the course of scanning PCI devices and enable it
again only when PME events are actually required to be generated from the
requested PCI state (for example, D3_hot or D3_cold). It is also safe to
disable PME again when the PME is disabled for the PCI devices.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some quirks should be called with interrupt disabled, we can't directly
call them in .resume_early. Also the patch introduces
pci_fixup_resume_early and pci_fixup_suspend, which matches current
device core callbacks (.suspend/.resume_early).
TBD: Somebody knows why we need quirk resume should double check if a
quirk should be called in resume or resume_early. I changed some per my
understanding, but can't make sure I fixed all.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch makes the needlessly global {pciehp,shpchp}_slot_with_bus
static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When Greg "fixed" the sysfs usage of that driver a while back, he seem
to have introduced a bug where the quotes are added around the name of
our specific sysfs files, thus breaking the user space tool.
This fixes it. Tested DLPAR operations on a POWER6 machine successfully.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The pciehp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the following errors reported by Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
kobject_add_internal failed for 2 with -EEXIST, don't try to register things with the same name in the same directory.
Pid: 1, comm: swapper Tainted: G W 2.6.26-rc3 #1
[<c0266980>] kobject_add_internal+0x140/0x190
[<c0266afd>] kobject_init_and_add+0x2d/0x40
[<c027bc91>] pci_hp_register+0x81/0x2f0
[<c027fd07>] pciehp_probe+0x1a7/0x470
[<c01b3b84>] sysfs_add_one+0x44/0xa0
[<c01b3c1f>] sysfs_addrm_start+0x3f/0xb0
[<c01b497a>] sysfs_create_link+0x8a/0xf0
[<c0279570>] pcie_port_probe_service+0x50/0x80
[<c02e0545>] driver_sysfs_add+0x55/0x70
[<c02e0662>] driver_probe_device+0x82/0x180
[<c02e07cc>] __driver_attach+0x6c/0x70
[<c02dfe0a>] bus_for_each_dev+0x3a/0x60
[<c05db2d0>] pcied_init+0x0/0x80
[<c02e04e6>] driver_attach+0x16/0x20
[<c02e0760>] __driver_attach+0x0/0x70
[<c02e0341>] bus_add_driver+0x1a1/0x220
[<c05db2d0>] pcied_init+0x0/0x80
[<c02e09cd>] driver_register+0x4d/0x120
[<c05db050>] ibm_acpiphp_init+0x0/0x190
[<c0125aab>] printk+0x1b/0x20
[<c05db2d0>] pcied_init+0x0/0x80
[<c05db2de>] pcied_init+0xe/0x80
[<c05c751a>] kernel_init+0x10a/0x300
[<c0120138>] schedule_tail+0x18/0x50
[<c0103b9a>] ret_from_fork+0x6/0x1c
[<c05c7410>] kernel_init+0x0/0x300
[<c05c7410>] kernel_init+0x0/0x300
[<c010485b>] kernel_thread_helper+0x7/0x1c
=======================
pci_hotplug: Unable to register kobject '2'<3>pciehp: pci_hp_register failed with error -22
Slot with the same name can be registered multiple times if shpchp or
pciehp driver is loaded after acpiphp is loaded because ACPI based
hotplug driver and Native OS hotplug driver trying to handle the same
physical slot. In this case, current pci_hotplug core will call
kobject_init_and_add() muliple time with the same name. This is the
cause of this problem. To fix this problem, this patch adds the check
into pci_hp_register() to see if the slot with the same name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
According to the PCI Express specification, we must wait for at least
1 second after turning power off before taking any action that relies
on power having been removed from the slot/adapter. For this, current
pciehp wait for 1 second after issuing the power off command in
hpc_power_off_slot() function. But waiting for 1 second in
hpc_power_off_slot() can make pciehp probing slow-down because pciehp
probe code calls hpc_power_off_slot() if the slot is not occupied just
in case. We don't need to wait for 1 second at the pciehp probe time
because there is no action on that empty slot. So move 1 second wait
from hpc_power_off_slot() to the caller of hpc_power_off_slot().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix improper long wait for command completion in pciehp probing.
As described in PCI Express specification, software notification is
not generated if the command that occurs as a result of a write to the
Slot Control register that disables software notification of command
completed events. Since pciehp driver doesn't take it into account,
such command is issued in pciehp probing, and it causes improper long
wait for command completion.
This patch changes the pciehp driver to take such command into
account.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).
The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.
This problem seems to be revealed by the commit
c27fb883df that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The shpchp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
to make sure get one online node.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Slot 03:00.* of JMicron controller has two functions, but one is
PCIE endpoint the other isn't PCIE device, very strange. PCIE spec
defines all functions should have the same config for ASPM, so disable
ASPM for the whole slot in this case.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Everybody wants to pass it a function pointer, and in fact, that is what
you _must_ pass it for it to make sense (since it knows that ia64 and
ppc64 use descriptors for function pointers and fetches the actual
address from there).
So don't make the argument be a 'unsigned long' and force everybody to
add a cast.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The acpi_query_osc() function can be called for the ACPI object that
doesn't have _OSC method. In this case, acpi_get_osc_data() would
allocate a useless memory region. To avoid this, we need to check the
existence of _OSC before calling acpi_get_osc_data() in acpi_query_osc().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This applies the NVidia MSI enabled flag for HT capable devices quirk
to ALi bridges as well.
As described in more detail in http://bugzilla.kernel.org/show_bug.cgi?id=10667
this is required for my board which is using an nForce 3 250Gb chipset with an
ALi M1695 northbridge.
It fixes a regression introduced in 2.6.24 that made the internal NIC of the
board unusable (MSI initialisation of the NIC but disabled MSI on the
northbridge devices.
Signed-off-by: Björn Krombholz <fox.box@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The following patch changes the intel-iommu.c code to use the TSC
instead of jiffies for detecting bad DMAR functionality. Some systems
with bad bios's have been seen to hang in early boot spinning in the
IOMMU_WAIT_IO macro. This patch will replace the infinite loop with a call to
panic.
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pci_osc_control_set() function can be called for the ACPI object
that doesn't have _OSC method. In this case, acpi_get_osc_data() would
allocate a useless memory region. To avoid this, we need to check the
existence of _OSC before calling acpi_get_osc_data(). Here is a patch
to fix this problem in pci_osc_control_set.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is an IA64 system here which have two pci root bridges with _OSC.
One _OSC disables SHPC control bit but the other not. Below patch makes
_OSC data per-device instead of one global, otherwise linux takes both
root bridges don't support SHPC.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix uninitialized variable in __pci_osc_support_set().
If the ACPI namespace doesn't have any device object corresponding to
the specified hid, 'retval' in __pci_osc_support_set() is not changed
by the acpi_query_osc() callback. Since 'retval' is not initizlized in
the current implementation, the contents of 'retval' is undefined in
this case. This causes a mis-handling of ctrlset_buf[OSC_SUPPORT_TYPE]
and will cause an unexpected result in the subsequent
pci_osc_control_set() call as a result.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
so let pci_cfg_space_size call it directly without flag.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (21 commits)
pciehp: fix error message about getting hotplug control
pci/irq: let pci_device_shutdown to call pci_msi_shutdown v2
pci/irq: restore mask_bits in msi shutdown -v3
doc: replace yet another dev with pdev for consistency in DMA-mapping.txt
PCI: don't expose struct pci_vpd to userspace
doc: fix an incorrect suggestion to pass NULL for PCI like buses
Consistently use pdev as the variable of type struct pci_dev *.
pciehp: Fix command write
shpchp: fix slot name
make pciehp_acpi_get_hp_hw_control_from_firmware()
pciehp: Clean up pcie_init()
pciehp: Mask hotplug interrupt at controller release
pciehp: Remove useless hotplug interrupt enabling
pciehp: Fix wrong slot capability check
pciehp: Fix wrong slot control register access
pciehp: Add missing memory barrier
pciehp: Fix interrupt event handlig
pciehp: fix slot name
Update MAINTAINERS with location of PCI tree
PCI: Add Intel SCH PCI IDs
...
People are confused by the following error message that actually is
not for indicating a error.
Cannot get control of hotplug hardware for pci %s
This patch changes this message to debug message.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
[PATCH 2/2] pci/irq: let pci_device_shutdown to call pci_msi_shutdown v2
this change
| commit 23a274c8a5
| Author: Prakash, Sathya <sathya.prakash@lsi.com>
| Date: Fri Mar 7 15:53:21 2008 +0530
|
| [SCSI] mpt fusion: Enable MSI by default for SAS controllers
|
| This patch modifies the driver to enable MSI by default for all SAS chips.
|
| Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
| Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
Causes the kexec of a RHEL 5.1 kernel to fail.
root casue: the rhel 5.1 kernel still uses INTx emulation. and
mptscsih_shutdown doesn't call pci_disable_msi to reenable INTx on kexec path
So call pci_msi_shutdown in the shutdown path to do the same thing to msix
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
[PATCH 1/2] pci/irq: restore mask_bits in msi shutdown -v3
Yinghai found that kexec'ing a RHEL 5.1 kernel with 2.6.25-rc3+ kernels
prevents his NIC from working. He bisected to
| commit 89d694b9db
| Author: Thomas Gleixner <tglx@linutronix.de>
| Date: Mon Feb 18 18:25:17 2008 +0100
|
| genirq: do not leave interupts enabled on free_irq
|
| The default_disable() function was changed in commit:
|
| 76d2160147
| genirq: do not mask interrupts by default
|
For MSI, default_shutdown will call mask_bit for msi device. All mask bits
will left disabled after free_irq. Then in the kexec case, the next kernel
can only use msi_enable bit, so all device's MSI can not be used.
So lets to restore the mask bit to its pci reset defined value (enabled) when
we disable the kernels use of msi to be a little friendlier to kexec'd kernels.
Extend msi_set_mask_bit to msi_set_mask_bits to take mask, so we can fully
restore that to 0x00 instead of 0xfe.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-pci:
x86: add pci=check_enable_amd_mmconf and dmi check
x86: work around io allocation overlap of HT links
acpi: get boot_cpu_id as early for k8_scan_nodes
x86_64: don't need set default res if only have one root bus
x86: double check the multi root bus with fam10h mmconf
x86: multi pci root bus with different io resource range, on 64-bit
x86: use bus conf in NB conf fun1 to get bus range on, on 64-bit
x86: get mp_bus_to_node early
x86 pci: remove checking type for mmconfig probe
x86: remove unneeded check in mmconf reject
driver core: try parent numa_node at first before using default
x86: seperate mmconf for fam10h out from setup_64.c
x86: if acpi=off, force setting the mmconf for fam10h
x86_64: check MSR to get MMCONFIG for AMD Family 10h
x86_64: check and enable MMCONFIG for AMD Family 10h
x86_64: set cfg_size for AMD Family 10h in case MMCONFIG
x86: mmconf enable mcfg early
x86: clear pci_mmcfg_virt when mmcfg get rejected
x86: validate against acpi motherboard resources
Fixed up fairly trivial conflicts in arch/x86/pci/{init.c,pci.h} due to
OLPC support manually.
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove proc_bus export and variable itself. Using pathnames works fine
and is slightly more understandable and greppable.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
scan AMD opteron io/mmio routing to make sure every pci root bus get correct
resource range. Thus later pci scan could assign correct resource to device
with unassigned resource.
this can fix a system without _CRS for multi pci root bus.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
in the device_add, we try to use use parent numa_node.
need to make sure pci root bus's bridge device numa_node is set.
then we could use device->numa_node direclty for all device.
and don't need to call pcibus_to_node().
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
reuse pci_cfg_space_size but skip check pci express and pci-x CAP ID.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Current implementation of pciehp_write_cmd() always enables command
completed interrupt. But pciehp_write_cmd() is also used for clearing
command completed interrupt enable bit. In this case, we must not set
the command completed interrupt enable bit. To fix this bug, this
patch add the check to see if caller wants to change command complete
interrupt enable bit.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current shpchp uses the combination of bus number and slot number as a
slot name. But it is not a good idea because bus number is not a
physical identifier but a logical identifier. This is against the shpc
specification. So remove the bus number from the physical identifier.
However, there are some platforms with the problem that it provides
the same slot number. For those platforms, this patch also introduces
new module option 'shpchp_slot_with_bus'. If it is specified, shpchp
uses the combination of bus number and slot number as a slot name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Clean up pciehp_ini(). This patch is trying to
- Remove redundant capablity checks that were already done in PCIe
port bus driver.
- Separate the code only for debugging and make debug information
easier to read.
- Make the entire code easier to read and understand what it is doing.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We must disable hotplug interrupt at controller relase time, otherwise
spurious interrupts might happen if any slot events occured (e.g. MRL
change) after unloading pciehp driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Hotplug interrupt is enabled at initialization and nobody clears it.
So we need to setup it in each command. This patch removes redundant
codes about this.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp saves only 8bits of Slot Capability registers in
ctrl->ctrlcap. But it refers more than 8bit for checking EMI capability.
It is clearly a bug and EMI would never work. To fix this problem,
this patch saves full Slot Capability contens in ctrl->slot_cap. It also
reduce the redundant reads of Slot Capability register. And this pach
also cleans up the macros to check the slot capabilitys (e.g. MRL_SENS(),
and so on).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp implementaion clears hotplug events without waiting for
command completion. Because of this, events might not be cleared properly.
To prevent this problem, we must use pciehp_write_cmd() to write to
Slot Control register.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the possible race condition between pcie_isr() and pciehp_write_cmd()
because of the lack of memory barrier.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp implementation disables and re-enables hotplug interrupts
in its interrupt handler. This operation might be intend to guarantee
that interrupts for the events newly occured during previous events are
being handled will be successfully generated. But current implementaion
has the following prolems.
- Current interrupt service routin clears status changes without
waiting command completion. Because of this, events might not be
cleared properly.
- Current interrupt service routine clears status changes caused by
disabling or enabling hotplug interrupts itself. This will lose new
events that occurs during previous interrupts are being handled.
- Current implementation doesn't have any serialization mechanism
between the code to wait for command completion and the interrupt
handler that clears the command completion events caused by itself.
There is clearly race conditions between them, and it may cause
the problem that waiting for command completion doesn't work for
example.
To fix those problems, this patch stops disabling/re-enabling hotplug
interrupts in interrupt service routine. Instead of this, this patch
re-inspects Slot Status register after clearing what is presumed to
be the last bending interrupt in order to guarantee that all interrupt
events are serviced.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp uses the combination of bus number and slot number as a
slot name. But it is not a good idea because bus number is not a
physical identifier but a logical identifier. This is against the PCIE
specification. So remove the bus number from the physical identifier.
However, there are some platforms with the problem that it provides
the same slot number. For those platforms, this patch also introduces
new module option 'pciehp_slot_with_bus'. If it is specified, pciehp
uses the combination of bus number and slot number as a slot name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stephen Rothwell noticed that:
Commit 2be621498d ("x86: dma-ops on highmem
fix") in Linus' tree introduced a new warning (noticed in the x86_64
allmodconfig build of linux-next):
drivers/pci/intel-iommu.c:2240: warning: initialization from incompatible pointer type
Which points at an instance of map_single that needs updating.
Fix it to the new prototype.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Running 'make oldconfig' I just noticed that PCIEASPM defaults to
'y' in Kconfig even though the feature is both experimental and the
help text recommends that if you are unsure you say 'n'.
It seems to me that this really should default to 'n', not 'y' at the
moment.
The following patch makes that change. Please consider applying.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 884525655d ("PCI: clean up resource
alignment management") didn't set the alignment information for the
cardbus window resources, causing their subsequent allocations to fail
miserably with a message like
yenta_cardbus 0000:15:00.0: device not available because of BAR 7 [100:1ff] collisions
yenta_cardbus: probe of 0000:15:00.0 failed with error -16
or similar.
This fixes it and clarifies the code a bit too (we used to have to use
the insane PCI bridge alignment logic that put the alignment in the
"start" field, this makes it use the slightly easier-to-understand
size-based alignment, and allows us to set the resource start to zero
until it gets allocated).
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch is an update to use an array instead of a list of
IOVA's in the implementation of defered iotlb flushes. It takes
inspiration from sba_iommu.c
I like this implementation better as it encapsulates the batch process
within intel-iommu.c, and no longer touches iova.h (which is shared)
Performance data: Netperf 32byte UDP streaming
2.6.25-rc3-mm1:
IOMMU-strict : 58Mps @ 62% cpu
NO-IOMMU : 71Mbs @ 41% cpu
List-based IOMMU-default-batched-IOTLB flush: 66Mbps @ 57% cpu
with this patch:
IOMMU-strict : 73Mps @ 75% cpu
NO-IOMMU : 74Mbs @ 42% cpu
Array-based IOMMU-default-batched-IOTLB flush: 72Mbps @ 62% cpu
Signed-off-by: <mgross@linux.intel.com>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: drivers/pci/built-in.o(.text+0x28ee9): Section mismatch in reference from the function pci_bus_assign_resources() to the function .devinit.text:pci_setup_bridge()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: drivers/pci/built-in.o(.text+0x28e1f): Section mismatch in reference from the function pci_bus_size_bridges() to the function .devinit.text:pci_bus_size_cardbus()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: drivers/pci/built-in.o(.text+0x150f): Section mismatch in reference from the function pci_scan_single_device() to the function .devinit.text:pci_scan_device()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: drivers/pci/built-in.o(.text+0xc4c): Section mismatch in reference from the function pci_add_new_bus() to the function .devinit.text:pci_alloc_child_bus()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 'power' attribute of the fakephp driver originally only let one turn a
slot off. If one tried to turn a slot on (echo 1 > .../power), it would
return ENODEV, as fakephp did not support this function.
An old (pre-git) patch changed this:
2004/11/11 16:33:31-08:00 jdittmer
[PATCH] fakephp: add pci bus rescan ability
http://article.gmane.org/gmane.linux.kernel/251183
Now writing "1" to the power attribute has the effect of triggering a bus
rescan, but it still returns ENODEV, probably an oversight in the above
patch.
Using the BusyBox echo will not produce an error message, but will
trigger *two* bus rescans (and return an exit code of 1):
~ # strace echo -n 1 > /sys/bus/pci/slots/0000:00:00.0/power
...
write(1, "1", 1) = -1 ENODEV (No such device)
write(1, "1", 1) = -1 ENODEV (No such device)
exit(1) = ?
Using cp gives a write error, even though the write did happen and a rescan
was triggered:
~ # echo -n 1 > tmp ; cp tmp /sys/bus/pci/slots/0000:00:00.0/power
cp: Write Error: No such device
It seems much better to return success instead of failure. The actual
status of the bus rescan is hard to return. It happens asynchronously in a
work thread, so the sysfs store functions returns before any status is
ready (the whole point of the work queue). And even if it didn't do this,
the rescan doesn't have any clear status to return.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Jan Dittmer <jdittmer@ppp0.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In drivers/pci/hotplug/ibmphp_core.c::ibmphp_init_devno() we allocate
space dynamically for a PCI irq routing table by calling
pcibios_get_irq_routing_table(), but we never free the allocated space.
This patch frees the allocated space at the function exit points.
Spotted by the Coverity checker. Compile tested only.
Please consider applying.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Done per Linus' request and suggestions. Linus has explained that
better than I'll be able to explain:
On Thu, Mar 27, 2008 at 10:12:10AM -0700, Linus Torvalds wrote:
> Actually, before we go any further, there might be a less intrusive
> alternative: add just a couple of flags to the resource flags field (we
> still have something like 8 unused bits on 32-bit), and use those to
> implement a generic "resource_alignment()" routine.
>
> Two flags would do it:
>
> - IORESOURCE_SIZEALIGN: size indicates alignment (regular PCI device
> resources)
>
> - IORESOURCE_STARTALIGN: start field is alignment (PCI bus resources
> during probing)
>
> and then the case of both flags zero (or both bits set) would actually be
> "invalid", and we would also clear the IORESOURCE_STARTALIGN flag when we
> actually allocate the resource (so that we don't use the "start" field as
> alignment incorrectly when it no longer indicates alignment).
>
> That wouldn't be totally generic, but it would have the nice property of
> automatically at least add sanity checking for that whole "res->start has
> the odd meaning of 'alignment' during probing" and remove the need for a
> new field, and it would allow us to have a generic "resource_alignment()"
> routine that just gets a resource pointer.
Besides, I removed IORESOURCE_BUS_HAS_VGA flag which was unused for ages.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's no reason for checking pdev->bus for being NULL here (and we'd
anyway Oops 3 lines below if it was).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This follows up 53a9bf4267. Some newer
CX700 BIOSes from our vendor have PCI Bus Parking disabled but PCI
Master read caching enabled. This creates problems such as system
freezing when both the network controller and the USB controller are
active and one of them is pretty busy (e.g. heavy network traffic).
This patch separates the checks and both the bus parking and the read
caching are disabled independently if either is enabled by the BIOS.
Signed-off-by: Tim Yamin <tim.yamin@zonbu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vital Product Data (VPD) may be exposed by PCI devices in several
ways. It is generally unsafe to read this information through the
existing interfaces to user-land because of stateful interfaces.
This adds:
- abstract operations for VPD access (struct pci_vpd_ops)
- VPD state information in struct pci_dev (struct pci_vpd)
- an implementation of the VPD access method specified in PCI 2.2
(in access.c)
- a 'vpd' binary file in sysfs directories for PCI devices with VPD
operations defined
It adds a probe for PCI 2.2 VPD in pci_scan_device() and release of
VPD state in pci_release_dev().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is for batching up the flushing of the IOTLB for the DMAR
implementation found in the Intel VT-d hardware. It works by building a list
of to be flushed IOTLB entries and a bitmap list of which DMAR engine they are
from.
After either a high water mark (250 accessible via debugfs) or 10ms the list
of iova's will be reclaimed and the DMAR engines associated are IOTLB-flushed.
This approach recovers 15 to 20% of the performance lost when using the IOMMU
for my netperf udp stream benchmark with small packets. It can be disabled
with a kernel boot parameter "intel_iommu=strict".
Its use does weaken the IOMMU protections a bit.
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
print_fn_descriptor_symbol() prints the address if we don't have a symbol,
so no need to print both.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch merges two functions into one allowing for a 3%
reduction in overhead in locating, allocating and inserting pages for
use in IOMMU operations.
Its a bit of a eye-crosser so I welcome any RB-tree / MM experts to take
a look. It works by re-using some of the information gathered in the
search for the pages to use in setting up the IOTLB's in the insertion
of the iova structure into the RB tree.
Signed-off-by: <mgross@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Each architecture has its own pcibios_enable_resources() implementation.
These differ in many minor ways that have nothing to do with actual
architectural differences. Follow-on patches will make most arches
use this generic version instead.
This version is based on powerpc, which seemed most up-to-date. The only
functional difference from the x86 version is that this uses "!r->parent"
to check for resource collisions instead of "!r->start && r->end".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Note: some devices might not work well with aspm, either because chipset
issue or device issue. The patch provide API (pci_disable_link_state),
driver can disable ASPM for specific device.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI bus names included in /proc/iomem and /proc/ioports are
of the form 'PCI Bus #XX' where XX is the bus number. This patch
changes the naming to 'PCI Bus XXXX:YY' where XXXX is the domain
number and YY is the bus number. For example, PCI bus 14 in
domain 0 will show as 'PCI Bus 0000:14' instead of 'PCI Bus #14'.
This change makes the naming consistent with other architectures
such as ia64 where multiple PCI domain support has been around
longer.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
#if 0 the no longer used pci_cleanup_aer_correct_error_status().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] pcie AER: don't check _OSC when acpi is disabled
when acpi=off or pci=noacpi, get warning
AER service couldn't init device 0000:00:0a.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:0e.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:0f.0:pcie01 - no _OSC support
AER service couldn't init device 0000:80:0b.0:pcie01 - no _OSC support
AER service couldn't init device 0000:80:0e.0:pcie01 - no _OSC support
AER service couldn't init device 0000:80:0f.0:pcie01 - no _OSC support
so don't check _OSC in aer_osc_setup
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch finally removes the global list of PCI devices. We are
relying entirely on the list held in the driver core now, and do not
need a separate "shadow" list as no one uses it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lets us check if the device is really added to the driver core or
not, which is what we need when walking some of the bus lists. The flag
is there in anticipation of getting rid of the other PCI device list,
which is what we used to check in this situation.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was marked incorrectly for some reason. Allow the ibmphp driver to
be built even if PCI_LEGACY is not enabled.
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes the depandancy of the cpcihp driver from the PCI_LEGACY
config option by removing its usage of the pci_find_bus() function.
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This cleans up the search.c file, now using the pci list of devices that
are created for the driver core, instead of relying on our separate list
of devices. It's better to use the functions already created for this
kind of thing, instead of rolling our own all the time.
This work is done in anticipation of getting rid of that second list of
pci devices all together.
And it ends up saving code, always a nice benefit.
This also removes one compiler warning for when CONFIG_PCI_LEGACY is
enabled as we no longer internally use the deprecated functions anymore.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes the pci_get_device_reverse function as there should not be
any need to walk pci devices backwards anymore. All users of this call
are now gone from the tree, so it is safe to remove it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No one is using this function anymore for quite some time, so remove it.
Everyone calls pci_dev_present() instead anyway...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An unused function that bloated the kernel only when CONFIG_EMBEDDED was
enabled...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Cleaned up references to cpumask_scnprintf() and added new
cpulist_scnprintf() interfaces where appropriate.
* Fix some small bugs (or code efficiency improvments) for various uses
of cpumask_scnprintf.
* Clean up some checkpatch errors.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Use new set_cpus_allowed_ptr() function added by previous patch,
which instead of passing the "newly allowed cpus" cpumask_t arg
by value, pass it by pointer:
-int set_cpus_allowed(struct task_struct *p, cpumask_t new_mask)
+int set_cpus_allowed_ptr(struct task_struct *p, const cpumask_t *new_mask)
* Modify CPU_MASK_ALL
Depends on:
[sched-devel]: sched: add new set_cpus_allowed_ptr function
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 3c0a654e39 and
fixes kernel bug #10245:
http://bugzilla.kernel.org/show_bug.cgi?id=10245
The HP Compaq nc6120 has the same PCI sub-device ID as the nx6110, and the
SMBus is used by ACPI for thermal management on the nc6120, so Linux should
not attach a native driver to it. This means that this quirk is unsafe and
has to be removed.
I also added a comment to help developers realize that adding new IDs to this
SMBus unhiding quirk table should be done only with great care, and in
particular only after checking that ACPI is not making use of the SMBus.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Tomasz Koprowski <tomek@koprowski.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 8fa5913d54, which
caused various interesting problems for people, including wrong resource
allocations. See for example bugzilla entry "2.6.25-rc2: ohci1394
problem (MMIO broken)" at
http://bugzilla.kernel.org/show_bug.cgi?id=10080
And Gary Hade says:
"The same change had also exposed an issue reported by Paul Martin that
has been causing an Oops while hotplugging ThinkPads to a ThinkPad
Dock II. See
http://lkml.org/lkml/2008/2/19/405http://bugzilla.kernel.org/show_bug.cgi?id=9961
I have a fix for the ThinkPad docking Oops but if the issue being
discussed here is caused by the transparent bridge sizing removal
change I totally agree that it should be reverted."
The transparent bridge sizing removal change was motivated by
insufficient PCI memory resource for a transparent bridge window that
was being created as a result of expansion ROM(s) being included in
the transparent bridge sizing calculations.
A later "PCI: Remove default PCI expansion ROM memory allocation"
change ( re: http://lkml.org/lkml/2007/12/11/361 ) removes the
expansion ROM(s) from the transparent bridge sizing calculations which
actually resolves the original issue in a different manner. So, even
if the "PCI: remove transparent bridge sizing" is not problematic it
is no longer needed anyway."
Identified-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Tested-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert as it is reported to cause problems for people.
commit 4348a2dc49
Author: Shaohua Li <shaohua.li@intel.com>
Date: Wed Oct 24 10:45:08 2007 +0800
pcie: utilize pcie transaction pending bit
PCIE has a mechanism to wait for Non-Posted request to complete. I think
pci_disable_device is a good place to do this.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the regression reported at
http://bugzilla.kernel.org/show_bug.cgi?id=10065
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Soeren Sonnenburg <kernel@nn7.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
lockdep goes off on the iova copy_reserved_iova() because it and a function
it calls grabs locks in the from, and the to of the copy operation.
The function grab locks of the same lock classes triggering the warning. The
first lock grabbed is for the constant reserved areas that is never accessed
after early boot. Technically you could do without grabbing the locks for the
"from" structure its copying reserved areas from.
But dropping the from locks to me looks wrong, even though it would be ok.
The affected code only runs in early boot as its setting up the DMAR
engines.
This patch gives the reserved_ioval_list locks special lockdep classes.
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a 2.6.25 regression reported by Alex Chiang.
Invoke pciehp_enable_slot() at startup only when pciehp_force=1.
Some HP equipment apparently cannot cope with it otherwise.
This restores the (previously working) 2.6.24 behaviour here,
while allowing machines that need a kick to use pciehp_force=1.
This was the original design back in October 2007,
but Kristen suggested we try without it first:
Kristen Carlson Accardi wrote:
>I think it would be ok to try allowing the slot to be enabled when not
>using pciehp_force mode. We can wrap it later if it proves to break things
This ended up breaking one of Alex's setups,
so it's time to put the wrapper back in now.
Signed-off-by: Mark Lord <mlord@pobox.com>
Acked-by: Alex Chiang <achiang@hp.com>
Acked-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCI busses can be registered multiple times, so we need to detect if we
have registered our bus structure in sysfs already. If so, don't do it
again.
Thanks to Guennadi Liakhovetski <g.liakhovetski@gmx.de> for reporting
the problem, and to Linus for poking me to get me to believe that it was
a real problem.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In drivers/pci/hotplug/ibmphp_ebda.c::ebda_rsrc_controller(), storage is
allocated with kzalloc() and assigned to 'tmp_slot'. Then lots of
stuff, like ->flag, ->supported_speed etc is set in tmp_slot. A bit
further down there's then this test :
if (!bus_info_ptr1) {
rc = -ENODEV;
goto error;
}
At this point, tmp_slot has not been assigned to anything, so when
erroring-out we want to free it, but nothing at the 'error:' label
free's 'tmp_slot' - and we can't really free 'tmp_slot' at 'error:'
since we may jump to that label later when 'tmp_slot' *has* been used
and we do not want it freed. So, the only sane option left seems to be
to kfree(tmp_slot) just before jumping to the 'error:' label in the one
place where this is what actually makes sense. The following patch does
just that and thus kills off a tiny potential memory leak.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the error code path in hpc_power_off_slot().
The Bad DLLP Mask bit must be restored before return.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the class_device cleanup of pci_bus, the error messages when
things go wrong are incorrect. So fix this up to properly report what
is really happening, if things go wrong.
Thanks to Kay for pointing out the issue.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix following warning:
WARNING: vmlinux.o(.text+0x47bdb1): Section mismatch in reference from the function pci_scan_child_bus() to the function .devinit.text:pcibios_fixup_bus()
We had plenty of functions that could be annotated __devinit but due to
the former restriction that exported symbols could not be annotated
they were not so. So annotate these function and fix the references
from the pci/hotplug/* code to silence the resuting warnings.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>