If the poll interval is set to 0 via new sysfs entry and device is
opened after that, polling is started with interval 0. This causes
huge CPU load. Same happens if the rate was 0 when the device was
closed and then reopened.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It does not make sense to wait poll_interval before performing first
read after opening the device, schedule the read immediately instead.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
S3C24XX touchscreen driver, originally written by Arnaud Patard and
other contributors. The driver has had substantial testing as well as
a number of tidying up passes done by Ben Dooks, as noted:
- added kernel-doc comments to most of the routines
- removed old code from pre adc framework days
- updated device probe code to use platform id list matching
- cleaned up debug, since printk() now has timestamp feature
- ensure code uses dev_() reporting macros where necessary
- remove ABS_PRESSURE reporting, tslib can be fixed
- ensure timer is removed on driver exit
- move to using dev_pmops for power management
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Zytronic USB-attached capacitive touchscreen support within the generic
USB touchscreen driver.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Function name is input_ff_destroy() and not input_ff_free()
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use strlcat() to append a string to the previously created first part.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On Zaurus, hx4700 and others pressure is reported inverted -- the lighter
the pressure, the bigger numerical value.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
usb_kill_urb() in disconnect is not needed as unregistering will cause
close() to be called.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
New at91sam9g45ekes board provides a LCD with resistive touchscreen.
This is the support of this feature by atmel_tsadcc driver. This also
sets up platform parameters to be passed to the driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a number of plafrom dependent parameters to atmel_tsadcc. The
touchscreeen driver can now take into account the slight differences
that exist between IPs included in diferent products. This will also
allow to adapt its behaivior to the caracteristics of the resistive
panel used.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tiny patch for setting capabilities using input API function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The touchpad on Acer Aspire 5720, 5520 and some other Aspire models
(signature 0x73, 0x02, 0x50) has a button that can be rocked in 4
different directions. Make the driver to generate BTN_0..BTN_3 events
in response. The Synaptics driver by default maps BTN_0 and BTN_1 to
up and down, so there should be no visible changes with the old setup
that generated BTN_FORWARD and BTN_BACK (also mapped to up and down).
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not start protocol detection assuming that middle mouse is present,
instead let individual protocols explicitly set this capability.
This fixes issue with Synaptics touchpads pretending that they have
middle button when hardware clearly reports otherwise.
Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The main input device of Lifebook touchscreens does not generate
left/right/middle button events and therefore should not be advertising
them in its capabilities.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Elantech touchpads work in absolute mode and do not generate relative
events so they should not be advertising them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Touchkit PS/2 touchscreen does not have left/right/middle buttons and
should not be advertising as capable of generating these events.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sysfs entry for reading and setting of the polling interval. If the
interval is set to 0, polling is stopped. Polling is restarted when
interval is changed to non-zero.
sysfs entries:
poll = current polling interval in msec (RW)
max = max allowed polling interval (RO)
min = min allowed polling interval (RO)
Minimum and maximum limit for interval can be set while setting up the
device.
Interval can be adjusted even if the input device is not currently open.
[dtor@mail.ru: add kernel doc markup for the new fields]
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move the code that deals with setting up each individual button out into
a new function to reduce the indentation and allow us to common up some
of the error recovery code.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio keys driver should be using <linux/gpio.h> instead
of <asm/gpio.h>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_keys driver is binding to a platform device but using pr_err()
to report errors. Change to using dev_err() so that all messages are
prefixed by the device name.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch allows UCB1400 to get IRQ GPIO from platform data. In case
platform_data are not supplied or the IRQ supplied in the platform_data
is negative, fall back to the old IRQ detection algorithm.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Panasonic CF-72 uses 6-byte protocol and does not need to be tied
to a particular port.
Signed-off-by: Abner Holsinger <9zabner@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit b7802c5c1e ("Input: psmouse - use boolean type") caused the
synaptics_hardware variable to be completely useless, as it is
constantly set to 'true' throughout the whole psmouse_extensions().
This was caused by the following hunk in the commit in question
- int synaptics_hardware = 0;
+ bool synaptics_hardware = true;
which is wrong and causes driver to issue extra reset when falling
back to bare PS/2 protocol.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The get parameter function should return a string without a life-feed.
Otherwise you'll see additional empty line in sysfs parameters file.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Even though input core tells us to restore LED state and repeat rate
at resume keyboard may be reconnected either by request from userspace
(via sysfs) or just by pulling it from the box and plugging it back in.
In these cases we still need to restore state ourselves.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should be sending EV_LED event down to drivers upon resume even in cases
when in-kernel state of the LED is off since device could come up with some
leds turned on.
Reported-and-tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now that input core acquires dev->event_lock spinlock and disables
interrupts when propagating input events, using spin_lock_bh() in
ff-memless driver is not allowed. Actually, the timer_lock itself
is not needed anymore, we should simply use dev->event_lock
as well.
Also do a small cleanup in force-feedback core.
Reported-by: kerneloops.org
Reported-by: http://www.kerneloops.org/searchweek.php?search=ml_ff_set_gain
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move xen_domain and related tests out of asm-x86 to xen/xen.h so they
can be included whenever they are necessary.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is nothing that disallows gpio-keys to share it's IRQ line
w/ other drivers. Make it use IRQF_SHARED in request_irq().
An example of other driver with which I'd like to share IRQ line
for GPIO buttons is ledtrig-gpio.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
drivers/input/misc/winbond-cir.c depends on LEDS_TRIGGERS so
add an appropriate select to drivers/input/misc/Kconfig
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If user presses keys while i8042 is being initialized there is a chance
that keyboard data will be mistaken for results of Read Control Register
command causing futher troubles. Work around this issue by reading CTR
several times and stop when we get matching results.
Reported-and-tested-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a driver for Dynapro serial touchscreen, which used to be
supported in Xorg. The driver needs updated inputattach utility to
initialize serial port and create proper serio device before the
driver will be bound to it.
Signed-off-by: Tias Guns <tias@ulyssis.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
OQO 01+ multimedia keys produce 6x on press, e0 6x upon release.
As a result, Linux thinks that another key has been pressed (or is
repeating), when it is actually a release of the same key. Mangle the
release scancode when running on OQO so that driver recognizes it as
such.
Since the device does not have external PS/2 ports mangling is safe
since there is no chance that an external keyboard is connected.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Optional open and close methods for preparing and closing
the device.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If left unsigned the hp_sdc_rtc_read_i8042timer() return value will not
be checked correctly.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some machines share same key list for volume up/down release key quirks,
use only one key list.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On this model, when KBD is in active multiplexing mode, acknowledgements
to reset and get ID commands issued on KBD port sometimes are delivered
to AUX3 port (touchpad) which messes up device detection. Legacy KBC
mode works fine and since there are no external PS/2 ports on this laptop
and no support for docking station we can safely disable active MUX mode.
Tested-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
cycle_kernel_lock() was added during the big BKL pushdown. It should
ensure the serializiation against driver init code. In this case there
is nothing to serialize. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.884891604@linutronix.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
input_devices_seq_start() uses mutex_lock_interruptible() to acquire
the input_mutex, but doesn't properly handle the situation when the
call fails (for example due to interrupt). Instead of returning NULL
(which indicates that there is no more data) we should return
ERR_PTR()-encoded error.
We also need explicit flag indicating whether input_mutex was acquired
since input_devices_seq_stop() is called whether input_devices_seq_start()
was successful or not.
The same applies to input_handlers_seq_start().
Reported-by: iceberg <strakh@ispras.ru>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to postpone restoring LED state and typematic settings until
keyboard is finished reconnecting upon resume. Normally driver core
and PM infrastructure takes care of proper ordering and dependencies,
but or case actual reconnect is done asynchronously from kseriod.
So while driver core thinks that keyboard was resumed and it is time
to let input core run it's resume handlers in reality keyboard is not
ready yet. The solution is to keep rescheduling work that adjusts LED
and rate settings until keyboard is fully enabled.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver enables keypad support on DaVinci platforms. DM365 is the
only platform that uses this driver at the moment.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- no spaces between function name and opening parenthesis
- switch statements were indented too much
This makes checkpatch (and me) happy.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- no spaces between function name and opening parenthesis
- switch statements were indented too much
This makes checkpatch (and me) happy.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix breakage caused by commit 9605fb48e1
While the input core indeed takes care of restoring led state and
typematic settings upon resume the driver still need to initialize
them properly when registering a new device
Reported-and-tested-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a new SERIO driver to support the Altera University
Program PS/2 controller.
[dtor@mail.ru: assorted cleanups]
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This small snippet escaped last round of int -> bool conversion.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently some of Toshiba Protege M300 identify themselves as
"Portable PC" in DMI so we need to add that to the DMI table as
well. We need DMI data so we can automatically lower Synaptics
reporting rate from 80 to 40 pps to avoid over-taxing their
keyboard controllers.
Tested-by: Rod Davison <roddavison@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Sometimes it is not clear why IRQ delivery test failed so let's
add some debug printks so we know the exact reason.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The "select" statement in the Kconfig ensures that all other users
of the xenbus will have the same dependency.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
libps2 can not be built in if i8042 is a module, all other combinations
are allowed.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If the sub-probe functions fail, we need to pass up the error code to the
higher levels from the probe function. We currently always return 0 even
if there was an error so higher levels don't report problems.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When the rotart_encoder driver is used to report relative axis
information the "steps" in the platform data could be missing
since it's not relevant.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The function bbc_remove and grover_remove are used only wrapped
by __devexit_p so define it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
drivers/input/input.c:1277: warning: 'input_dev_reset' defined but not used
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix these warnings:
drivers/built-in.o: In function `apanel_remove':
apanel.c:(.text+0x56e852): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `apanel_probe':
apanel.c:(.text+0x56eae3): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `acpi_fujitsu_hotkey_add':
fujitsu-laptop.c:(.text+0x5d7647): undefined reference to `led_classdev_register'
fujitsu-laptop.c:(.text+0x5d76b5): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `wbcir_probe':
winbond-cir.c:(.devinit.text+0x5f375): undefined reference to `led_classdev_register'
winbond-cir.c:(.devinit.text+0x5f663): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `wbcir_remove':
winbond-cir.c:(.devexit.text+0x7f23): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `fujitsu_cleanup':
fujitsu-laptop.c:(.exit.text+0xbe37): undefined reference to `led_classdev_unregister'
fujitsu-laptop.c:(.exit.text+0xbe53): undefined reference to `led_classdev_unregister'
It happens because the new INPUT_WINBOND_CIR driver relies on new-leds
infrastructure - but does not select it in drivers/input/misc/Kconfig.
But it selects LEDS_CLASS, which confuses a number of other drivers into
thinking that all the leds infrastructure is in place.
Fix this by selecting NEW_LEDS as well, like similar drivers do.
Eventually, this whole leds infrastructure complexity should be
cleaned up, it's been going on for years.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/battery-2.6:
power_supply: Add driver for the PMU on WM831x PMICs
ds2760_battery: Fix integer overflow for time_to_empty_now
wm97xx_battery: Convert to dev_pm_ops
wm97xx_battery: Use irq to detect charger state
wm97xx_battery: Use platform_data
wm97xx-core: Pass platform_data to battery
ds2760_battery: implement set_charged() feature
power_supply: get_by_name and set_charged functionality
power_supply: EXPORT_SYMBOL cleanups
ds2760_battery: add current_accum module parameter
ds2760_battery: handle full_active_uAh == 0 case correctly
ds2760_battery: add rated_capacity module parameter
ds2760_battery: export more features
ds2760_battery: delay power supply registration
wm8350_power: Implement charge type property
power_supply: Add a charge_type property, and use it for olpc driver
olpc_battery: Add an 'error' sysfs device that displays raw errors
Revert "power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL"
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This version only supports individual cells (no slide support yet).
The code has been tested on proprietary development ARM board, but
should work fine on other machines.
Signed-off-by: Raphael Derosso Pereira <raphaelpereira@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
Add a driver for the the Consumer IR (CIR) functionality of the Winbond
WPCD376I chipset (found on e.g. Intel DG45FC motherboards).
Signed-off-by: David Härdeman <david@hardeman.nu>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert max7359 driver to use IRQ threading instead of using
workqueue.
Tested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Maxim MAX7359 is a I2C interfaced key switch controller which
provides microprocessors with management of up to 64 key switches.
This patch adds support for the MAX7359 key switch controller.
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (262 commits)
sh: mach-ecovec24: Add user debug switch support
sh: Kill off unused se_skipped in alignment trap notification code.
sh: Wire up HAVE_SYSCALL_TRACEPOINTS.
video: sh_mobile_lcdcfb: use both register sets for display panning
video: sh_mobile_lcdcfb: implement display panning
sh: Fix up sh7705 flush_dcache_page() build.
sh: kfr2r09: document the PLL/FLL <-> RF relationship.
sh: mach-ecovec24: need asm/clock.h.
sh: mach-ecovec24: deassert usb irq on boot.
sh: Add KEYSC support for EcoVec24
sh: add kycr2_delay for sh_keysc
sh: cpufreq: Include CPU id in info messages.
sh: multi-evt support for SH-X3 proto CPU.
sh: clkfwk: remove bogus set_bus_parent() from SH7709.
sh: Fix the indication point of the liquid crystal of AP-325RXA(AP3300)
sh: Add EcoVec24 romImage defconfig
sh: USB disable process is needed if romImage boot for EcoVec24
sh: EcoVec24: add HIZA setting for LED
sh: EcoVec24: write MAC address in boot
sh: Add romImage support for EcoVec24
...
The MELPAS MCS-5000 is the touchscreen controller. The overview of this
controller can see at the following website:
http://www.melfas.com/product/product01.asp?k_r=eng_
This driver is tested on s3c6410 NCP board and supports only the i2c
interface.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The genirq already provides default hard IRQ handler for threaded
IRQs, no need to implement our own here.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
cancel_delayed_work() may spin and therefore should not be used in
interrupt contexts.
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The AD7889 is a new part but 100% software compatible with the AD7879, so
add it to the id_table and help text.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now that input core takes care of restoring state of input devices
upon resume we don't need to do anything special here.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Automatically turn off leds and sound effects as part of suspend
process and restore led state, sounds and repeat rate at resume.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The serio ports on i8042 are not completely isolated; while we provide
enough locking to ensure proper serialization when accessing control
and data registers AUX and KBD ports can still have an effect on each
other on PS/2 protocol level. The most prominent effect is that
issuing a command for the device connected to one port may cause
abort of the command currently executing by the device connected to
another port.
Since i8042 nor serio subsystem are not aware of the details of the
PS/2 protocol (length of the commands and their replies and so on) the
locking should be done on libps2 level by adding special handling when
we see that we are dealing with serio port on i8042.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a driver for misc input events for the PCAP2 PMIC, it handles
the Power key and the Headphone button.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Ilya Petrov <ilya.muromec@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Touchscreen driver for the PCAP2 multi function device used in
Motorola EZX smartphones.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of PMICs support control of initial power on
through the ON pin on the device with soft control of the pin
at other times. Represent this to userspace as KEY_POWER.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Driver Core: devtmpfs - kernel-maintained tmpfs-based /dev
debugfs: Modify default debugfs directory for debugging pktcdvd.
debugfs: Modified default dir of debugfs for debugging UHCI.
debugfs: Change debugfs directory of IWMC3200
debugfs: Change debuhgfs directory of trace-events-sample.h
debugfs: Fix mount directory of debugfs by default in events.txt
hpilo: add poll f_op
hpilo: add interrupt handler
hpilo: staging for interrupt handling
driver core: platform_device_add_data(): use kmemdup()
Driver core: Add support for compatibility classes
uio: add generic driver for PCI 2.3 devices
driver-core: move dma-coherent.c from kernel to driver/base
mem_class: fix bug
mem_class: use minor as index instead of searching the array
driver model: constify attribute groups
UIO: remove 'default n' from Kconfig
Driver core: Add accessor for device platform data
Driver core: move dev_get/set_drvdata to drivers/base/dd.c
Driver core: add new device to bus's list before probing
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to problems at cam.org, my nico@cam.org email address is no longer
valid. FRom now on, nico@fluxnic.net should be used instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (52 commits)
Input: bcm5974 - silence uninitialized variables warnings
Input: wistron_btns - add keymap for AOpen 1557
Input: psmouse - use boolean type
Input: i8042 - use platform_driver_probe
Input: i8042 - use boolean type where it makes sense
Input: i8042 - try disabling and re-enabling AUX port at close
Input: pxa27x_keypad - allow modifying keymap from userspace
Input: sunkbd - fix formatting
Input: i8042 - bypass AUX IRQ delivery test on laptops
Input: wacom_w8001 - simplify querying logic
Input: atkbd - allow setting force-release bitmap via sysfs
Input: w90p910_keypad - move a dereference below a NULL test
Input: add twl4030_keypad driver
Input: matrix-keypad - add function to build device keymap
Input: tosakbd - fix cleaning up KEY_STROBEs after error
Input: joydev - validate axis/button maps before clobbering current ones
Input: xpad - add USB ID for the drumkit controller from Rock Band
Input: w90p910_keypad - rename driver name to match platform
Input: add new driver for Sentelic Finger Sensing Pad
Input: psmouse - allow defining read-only attributes
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
[ARM] Update mach-types
ARM: 5636/1: Move vendor enum to AMBA include
ARM: Fix pfn_valid() for sparse memory
[ARM] orion5x: Add LaCie NAS 2Big Network support
[ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
ARM: 5689/1: Update default config of HP Jornada 700-series machines
ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
ARM: 5688/1: ks8695_serial: disable_irq() lockup
ARM: 5687/1: fix an oops with highmem
ARM: 5684/1: Add nuc960 platform to w90x900
ARM: 5683/1: Add nuc950 platform to w90x900
ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
MMC: MMCI: convert realview MMC to use gpiolib
ARM: 5685/1: Make MMCI driver compile without gpiolib
ARM: implement highpte
ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
...
Fix up trivial conflict in arch/arm/kernel/signal.c.
It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
After KYCR2 is set, udelay might become necessary if there are only a
small number of keys attached. This patch introduces an optional delay
through the platform data to address this problem.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
i8042 is not hot-pluggable and we create the device when we register
the driver, so let's save some memory by using platform_device_probe
and using __init instead of __devinit.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Ever since we switched from having a polling timer to registering IRQ
handlers for both keyboard and AUX ports at the driver registration
time, on certain boxes probing for a mouse results in keyboard
stopping working. The only real difference between old and new way is
that before we disabled ports after unsuccessful probe whereas now we
leave them as is. Try to emulate the old behavior by disabling and
immediately re-enabling AUX and KBD ports when corresponding serio
port is being closed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It seems that many laptops do not fully implement AUX LOOP command in
their keyboard controllers, causing issues with touchpad detection.
We know however that almost every laptop/portable uses a PS/2 pointing
device and, even if user disables it in favor of an external mouse,
the system will not use IRQ 12 for anything else. Therefore we may
bypass AUX IRQ delivery test when running on a laptop and assume that
it is routed properly.
Just to be safe we require the box to have good PNP data in order to
bypass the test.
[Jin Dongming <jin.dongming@np.css.fujitsu.com>: fix crash caused
by missing terminator in the DMI table]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Compaq Presario R4000-series laptops are not sending a "volume up button
release" and "volume down button release" signal in the PS/2 protocol for
atkbd. The URL below has some of confirmed reports:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/385477
Signed-off-by: Dave Andrews <jetdog330@hotmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is no need for locking when we send query and start commands
to the touchscreen since there is no concurrency.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are more and more laptop requiring use of force_release quirk
for their multimedia and other specialized keys. Adding their DMI data
to the kernel is not sustainable; instead we will rely on help from
userspace (HAL) to do that for us.
This patch creates a new 'force_release' sysfs attribute (that belongs
to serio device to which keyboard is attached) which can be used to set
up force_release keymap. For example, Dell laptop owners might do:
echo 133-139,143,147 > /sys/devices/platform/i8042/serio0/force_release
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add the cpu.c and dev.c and modify w90p910 platform
to apply to use the common API(provided by cpu.c and dev.c)
at the same time, I renamed all w90x900 to nuc900 in every
c file of w90x900 platform and touchscreen's driver name.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We should first check whether platform data is NULL or not, before
dereferencing it to get the keymap.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a driver for the keypad controller on TWL4030 family chips.
These support up to an 8x8 key matrix. The TWL4030 multifunction
chips are mostly used on OMAP3 (or OMAP 2430) based boards.
[dtor@mail.ru: switch to matrix-keypad framework, fix changing
keymap from userspace]
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Direct to fail2 to gpio_free() the KEY_STROBEs as well as the KEY_SENSEs.
[dtor@mail.ru: change keymap from unsigned int to unsigned short]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Up to now axis and button map validation was done after the user-supplied
values were copied over the driver's map. This patch copies the
user-supplied values into temporary buffers and validated them before
overwriting the driver's permanent maps.
Also change JSIOCGBTNMAP and JSIOCGAXMAP to return number of bytes returned
to userspace instead of 0.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When KBC is in active multiplexing mode, disabling and re-enabling the
touchpad with the special key leaves the touchpad dead. Since the laptop
does not have any external PS/2 ports disabling MUX mode should be safe.
Reported-by: Eugeniy Meshcheryakov <eugen@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes, when using the touchscreen, it stops working till next restart
and the following message is printed:
ucb1400: unexpected IE_STATUS = 0x0
The following patch retriggers the touchscreen interrupt unconditionally.
This prevents hanging of the touchscreen in case of bogus interrupt
occurence.
Signed-off-by: Pavel Revak <palo@bielyvlk.sk>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch enables ADC filtering on UCB1400 codec by default. The
benefit from this change is mostly on some Colibri boards where
the ADCSYNC pin of the UCB1400 codec isn't connected causing the
touchscreen to jitter very badly. This change has no visible
effect on boards where the ADCSYNC pin is connected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Palo Revak <palo@bielyvlk.sk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is the driver for Sentelic Finger Sensing Pad which can be found
on MSI WIND Netbook.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The KEY_MAX change in 2.6.28 changed the values of the JSIOCSBTNMAP and
JSIOCGBTNMAP constants; software compiled with the old values no longer
works with kernels following 2.6.28, because the ioctl switch statement
no longer matches the values given by the software. This patch handles
these ioctls independently of the length of data specified, and applies the
same treatment to JSIOCSAXMAP and JSIOCGAXMAP which currently depend on
ABS_MAX.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds a struct eeti_ts_platform_data which currently holds only one
value to specify the interrupt polarity.
The driver has a fallback if no platform data is passed in via the
i2c_board_info, so no regression is caused.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also have the driver send MSC_SCAN events as most keyboards do to aid
in updating keymap from userspace.
Tested-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add keypad driver for the 4x4 keypad on an evaluation board based
on w90p910.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
hil_kbd and hil_ptr look like twins so it makes sense to combine them
into a single driver.
[deller@gmx.de: add MODULE_ALIAS() entry for mouse]
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Rename functions and variables from [hil_]kbd to [hil_]dev in
preparation of merging hil_kbd and hil_ptr.
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove assumption on the shift and size of rows/columns form
matrix_keypad driver.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Prestigio 157, an old no-name clone laptop uses input keys very
similar to the Wistron 1557/MS2141 with the addition of BIOS-controlled
wireless radio frequency kill switch.
This patch adds support for the RF kill switch control and adds manual
identification of the model.
The Prestigio does not expose any recognisable identity via dmidecode
and so requires manual selection at module init using
force=1 keymap=prestigio
Signed-off-by: TJ <ubuntu@tjworld.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The OLPC XO laptop incorporates a combination touchpad/tablet device
which unfortunately requires frequent recalibration. The driver will
force this automatically when various suspicious behaviors are
observed, and the user can recalibrate manually (with a special
keyboard sequence). There's currently no way, however, for an external
program to cause recalibration. We can not use the reconnect
capability which is already available in /sys because full reset of
the touchpad takes 1.1 - 1.2 secons which is too long.
This patch creates a new node in /sys which, when written with '1',
will force a touchpad recalibration; no other writes (or reads)
of this node are supported.
Signed-off-by: Paul Fox <pgf@laptop.org>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The synaptic touchpad on the Asus G1S is not properly detected when
rebooting machine or on cold boot from time to time. Adding the Asus
G1S to the noloop exception table resolves the issue.
# dmidecode 2.10
SMBIOS 2.4 present.
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: ASUSTeK Computer Inc.
Product Name: G1S
Version: 1.0
Wake-up Type: Power Switch
SKU Number:
Family:
Signed-off-by: Jory A. Pratt <geekypenguin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Check the result when sending the power down command to the controller.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In cases when get_pendown_state callback is not available have
the driver to fallback on pressure calculation to determine if
the pen is up.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for the e2i touchscreen controller used in the
Mimo 740 (and probably in other e2i touchscreen products). Tested on
Mimo 740.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Don't read coordinates during probe of the driver, just power down
the controller and wait for interrupts.
Signed-off-by: Richard Röjfors<richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make init_platform_hw and exit_platform_hw callbacks optional since
they are not needed on all platforms.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Properly shut off interrupts/delayed work by free-ing IRQ first
and then ensuring that enable/disable is balanced. Also add
__devinit/__devexit markings, restore poll delay/period scheduling
logic, make sure we call exit_platform_hw() method when probe
fails.
Tested-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since it's not allowed to do synchronous I2C in the HR timer callback
context we have to switch to using the global workqueue. The work is
scheduled every 1ms when polling rather than 5 us.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
clk_disable() in remove method is not needed since we already
have clk_disable in pxa27x_keypad_close().
Also make sure the driver uses resource_size() and helpers from
include/input/matrix_keypad.h
Tested-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch allows tweaking the behaviour of GPIO_STATUS register
shift quirk that's in wm97xx-core. The problem with GPIO_STATUS
register being shifted by one doesn't appear on all hardware it
seems and causes problems with accelerated touchscreen drivers on
Palm hardware. Therefore an accelerated touchscreen driver can select
if the shift is/isn't happening on the hardware.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch refactors the Mainstone accelerated touch code a little and
adds support for interrupt driven touchscreen on Palm LifeDrive, TX and
Tungsten T5.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Netbooks based on the Soltech TA12 do not send a key release
for volume keys causing Linux to think the key is constantly
being pressed forever.
Added quirk data for forced release keys.
BugLink: https://bugs.launchpad.net//bugs/397499
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 3d5cb60e ("Input: simplify name handling for certain input
handles") introduced a regression for the EVIOCGNAME/JSIOCGNAME
ioctl.
Before this, patch, the platform device's name was given back to
userspace which was good to identify devices. After this patch, the
device is ("event%d", minor) which is not descriptive at all.
This fixes the behaviour by taking dev->name.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reviewed-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now that clk API is available on ARM we can use it in the driver.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver for UCB1400 touchscreen controllers contains a function named
ucb1400_ts_pen_down(), but it returns 0 if the pen is down and 1 if it's up.
This causes confusion, especially since it's used as a boolean truth value
later in the code. This patch renames it.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch enables forced releasing of the Fn+Volume hotkeys
on the Fujitsu Siemens Amilo Pi 3525 notebook.
Signed-off-by: Simon Davie <nexx@nexxdesign.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Gets rid of the following warning:
Platform driver 'pcspkr' needs updating - please use dev_pm_ops
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds DMI information to automatically load the correct
layout for the Maxdata Pro 7000X/DX notebook models. Such notebooks
are clones of Fujitsu Amilo V2000, the hook for the v2000 is being
used and I have tested that perfectly works.
The immediate result of integrating this patch is that the five
special buttons will work on these specific notebook models and that
the RF killswitch will not be activated after suspend. This patch
definitively obsoletes the fsam7400 module which I was still needing
to enable wifi and to fix the RF killswitch suspend problem; in the
current 2.6.30 kernel it is necessary to load the wistron_btns module
with options 'force=1 keymap=1557/MS2141', which was not anyway a
complete workaround.
Signed-off-by: Giuseppe Mazzotta <g.mazzotta@iragan.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gpio_mouse - use standard driver registration method
Input: mark serio and i8042 as suspended when hibernating too
Input: add support for generic GPIO-based matrix keypad
Input: arrange keyboards alphabetically
Input: gpio-keys - avoid possibility of sleeping in timer function
Input: gpio-keys - revert 'change timer to workqueue'
Input: dm355evm_keys - fix kconfig symbol names
Input: wacom - add DTF720a support and fix rotation on Intuos3
Input: i8042 - more reset quirks for MSI Wind-clone netbooks
Add support for the JASTEC/DigiTech DTR-02U USB touch screen
controllers.
Signed-off-by: Jim Persson <jim-linux@nurd.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use the function resource_size, which reduces the chance of
introducing off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch is needed when the gpio's became available only at late
stages, for example, when using i2c gpio expander.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Serio ports are not being restarted any longer because resume operations
after hibernate do nothing, since the device has not been marked as
suspended. This happens because suspend is only considering the SUSPEND
event but not the FREEZE event.
Note that this driver has still to migrate to dev_pm_ops, but this fixes
this particular bug now.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Original patch by Marek Vasut, modified by Eric in:
1. use delayed work to simplify the debouncing
2. combine col_polarity/row_polarity into a single active_low field
3. use a generic bit array based XOR algorithm to detect key
press/release, which should make the column assertion time
shorter and code a bit cleaner
4. remove the ALT_FN handling, which is no way generic, the ALT_FN
key should be treated as no different from other keys, and
translation will be done by user space by commands like 'loadkeys'.
5. explicitly disable row IRQs and flush potential pending work,
and schedule an immediate scan after resuming as suggested
by Uli Luckas
6. incorporate review comments from many others
Patch tested on Littleton/PXA310 (though PXA310 has a dedicate keypad
controller, I have to configure those pins as generic GPIO to use this
driver, works quite well, though), and Sharp Zaurus model SL-C7x0
and SL-C1000.
[dtor@mail.ru: fix error unwinding path, support changing keymap
from userspace]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Reviewed-by: Uli Luckas <u.luckas@road.de>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Convert the dm355evm keys driver to use IRQ threading instead of
a private workqueue. IRQ threads were added to Linux after this
driver was written, and in this case fit what the driver needs.
(Although the non-shared thread costs more runtime memory.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_get_value function may sleep, so it should not be called in a
timer function. Move gpio_get_value calls to workqueue.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit 0b346838c5.
This commit breaks GPIO debouncing by replacing the original mod_timer
with schedule_delayed_work in the interrupt handler. The latter does not
kick the timer further on GPIO line changes as it should to perform
debouncing.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When testing Moblin on various netbooks, we've got reports that
many MSI Wind clones need the i8042 reset quirks for the keyboard
and/or touchpad's proper function.
Signed-off-by: Yan Li <yan.i.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: add driver for Synaptics I2C touchpad
Input: synaptics - add support for reporting x/y resolution
Input: ALPS - handle touchpoints buttons correctly
Input: gpio-keys - change timer to workqueue
Input: ads7846 - pin change interrupt support
Input: add support for touchscreen on W90P910 ARM platform
Input: appletouch - improve finger detection
Input: wacom - clear Intuos4 wheel data when finger leaves proximity
Input: ucb1400 - move static function from header into core
Input: add driver for EETI touchpanels
Input: ads7846 - more detailed model name in sysfs
Input: ads7846 - support swapping x and y axes
Input: ati_remote2 - use non-atomic bitops
Input: introduce lm8323 keypad driver
Input: psmouse - ESD workaround fix for OLPC XO touchpad
Input: tsc2007 - make sure platform provides get_pendown_state()
Input: uinput - flush all pending ff effects before destroying device
Input: simplify name handling for certain input handles
Input: serio - do not use deprecated dev.power.power_state
Input: wacom - add support for Intuos4 tablets
...
This driver supports Synaptics I2C touchpad controller on eXeda
mobile device. Unfortunaltely it only works in relative mode and
thus is not comaptible with Xorg Synaptics driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics uses anisotropic coordinate system. On some wide touchpads
vertical resolution can be twice as high as horizontal which causes
unequal sensitivity on x/y directions. Add support for reading the
resolution with EVIOCGABS ioctl.
Signed-off-by: Tero Saarni <tero.saarni@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
PIT_TICK_RATE is currently defined in four architectures, but in three
different places. While linux/timex.h is not the perfect place for it, it
is still a reasonable replacement for those drivers that traditionally use
asm/timex.h to get CLOCK_TICK_RATE and expect it to be the PIT frequency.
Note that for Alpha, the actual value changed from 1193182UL to 1193180UL.
This is unlikely to make a difference, and probably can only improve
accuracy. There was a discussion on the correct value of CLOCK_TICK_RATE
a few years ago, after which every existing instance was getting changed
to 1193182. According to the specification, it should be
1193181.818181...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.osdl.org
Acked-by: Chris Wright <chrisw@sous-sol.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support to the input core to report the proper device name to
userspace for their devices.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
I found the PrimeCell/AMBA Bus drivers distrusting the resource
passed in as part of the struct amba_device abstraction. This
patch removes all hard coded resource sizes found in the PrimeCell
drivers and move the responsibility of this definition back to
the platform/board device definition, which already exist and
appear to be correct for all in-tree users of these drivers.
We do this using the resource_size() inline function which was
also replicated in the only driver using the resource size, so
that has been changed too. The KMI_SIZE was left in kmi.h in case
someone likes it. Test-compiled against Versatile and Integrator
defconfigs, seems to work but I don't posess these boards and
cannot test them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When pressing any button belonging to the touchpoint, the generated
click events don't belong to the touchpoint but to the touchpad.
This patch fixes this behaviour, the events will be sent via the
correct device, so scrolling with touchpoint is possible.
Signed-off-by: Ulrich Dangel <uli@spamt.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_get_value function of I2C/SPI GPIO expander may sleep thus this
function call can not be called in a timer function.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some SoCs support only pin change interrupts on GPIO pins used as irq
lines.
The ads7846 core is not affected from the additional irqs on the rising
edge because the code accounts touch bounce anyway by kicking in a timer
and disabling the irq after the first request and reenabling the irq after
a timeout when there is no longer pen down detected.
Signed-off-by: Michael Roth <mroth@nessie.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The touchscreen works in two modes, wait trigger mode and auto-semi
mode. The device starts in wait trigger mode and waits until pressure
is detected, then device sets WT_INT bit and raises an interrupt.
The driver should put the device into auto-semi mode and prepare for
reading first X and then Y coordinates. When coordinate data is ready
the driver sets ADC_INT bit and raises interrupt again.
[dtor@mail.ru: various cleanups]
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The appletouch driver is prone to reporting multiple fingers when only
one is pressing. The appletouch driver queries an array of pressure
sensors and counts local maxima in pressure to determine the number of
fingers. It just does this on the raw values, so a data stream like:
0 100 250 300 299 300 250 100 0
actually registers as 2 fingers.
This patch updates the logic to ignore small dips in pressure that are
less than the threshold.
Signed-off-by: Jeremy Huddleston <jeremyhu@freedesktop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: libps2 - better handle bad scheduler decisions
Input: usb1400_ts - fix access to "device data" in resume function
Input: multitouch - augment event semantics documentation
Input: multitouch - add tracking ID to the protocol
Sometimes devices send us their responses in time but due to
unfortunate scheduling decisions the receiving thread does not
get scheduled till much later and we erroneously decide that
device timed out. Work around this problem by checking whether we
received the data we needed instead of checking timeout
condition.
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
platform_data != driver_data
driver data is actually the "correct" place of the struct however it is
not placed there due to the need of the ac97 struct. This is broken since
d9105c2b01 aka "[ARM] 5184/1: Split ucb1400_ts into core and touchscreen"
Signed-off-by: Manuel Traut <manut@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are a few multi-touch devices that support finger tracking
well in hardware, Stantum being the prime example. By exposing the
tracking ID in the MT protocol, evdev bandwidth and cpu usage in
user space can be reduced.
This patch adds the ABS_MT_TRACKING_ID to the MT protocol.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Stéphane Chatty <chatty@enac.fr>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a driver for EETI's I2C connected touchscreens.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Tested-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
No point in using atomic bitops when setting the input device keybits.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
lm8323 is the keypad driver used in n810 device.
[akpm@linux-foundation.org: coding-style fixes]
[dtor@mail.ru: various cleanups]
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It appears that when the XO touchpad unit resets from ESD, it sends AA
AA instead of AA 00, the psmouse-base code handles the case of AA 00 by
triggering a serio reconnect for the port, causing a full reprobe of
the device.
Testing with OFW shows that this is likely to solve the problem, so
the attached patch simply expands the existing test to also catch AA AA.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The platform codes must provide get_pendown_state() for the driver
to work properly.
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The destruction of a input device in uinput is triggered by an ioctl().
If a process tries to destroy an input device while other is uploading a
force feedback effect by evdev to the same device, they'll deadlock.
This patch fixes the problem by flushing all pending FF uploads before
destroying the device and preventing new uploads during this operation.
[dtor@mail.ru: fix logic that ensures we don't submit new requests
to the device that is being destroyed.]
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc2007 - fix locking in hrtimer handler
Input: atkbd - add force release keys quirk for Amilo Xi 3650
Input: ff-memless - fix signed to unsigned bit overflow
Input: joydev - blacklist digitizers
Now that hrtimers are always running in hard irq context we can't
unconditionally enable interrupts at the end of the timer function.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For evdev, joydev and mousedev, instead of having a separate character array
holding name of the handle, use struct devce's name which is the same.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When we get a relative packet from trackpoint (when we deal with
touchscreen/trackpoint combo) we should not send events for the device
corresponding to touchscreen as it confuses evtouch driver (it looks
like it keeps previously reported absolute coordinates and the cursor
stays in the same place).
Reported-by: Marcin Drewka <laimoriel@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dell Latitude D630/D800 have DualPoint (touchpad plus trackpoint)
instead of a simple touchpad and a pass-through port for external
PS/2 mouse.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When userspace sets effect->u.rumble.strong_magnitude to 0x8001 or
larger, ml_combine_effects() would always return strong_magnitude
0xffff.
Problem is that 'gain' is passed in as signed integer. Multiplying
magnitude (__u16) with gain (int) causes magnitude read as signed and
results negative value (with magnitude > 0x8000). This signed integer
is then divided and value, still negative, converted to 32bit unsigned
integer. Finally checking combine overflow min(new+old, 0xffff) gives
out 0xffff.
Fix is to simply change 'gain' to unsigned int.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
BTN_TOUCH is not set by the wacom driver which causes it to be handled by the
joydev driver while the resulting device is broken. This causes problems with
applications that try to use a joystick device.
Ubuntu BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/300143
Signed-off-by: Tim Cole <tim.cole@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Acked-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: document the multi-touch (MT) protocol
Input: add detailed multi-touch finger data report protocol
Input: allow certain EV_ABS events to bypass all filtering
Input: bcm5974 - add documentation for the driver
Input: bcm5974 - augment debug information
Input: bcm5974 - Add support for the Macbook 5 (Unibody)
Input: bcm5974 - add quad-finger tapping
Input: bcm5974 - prepare for a new trackpad header type
Input: appletouch - fix DMA to/from stack buffer
Input: wacom - fix TabletPC touch bug
Input: lifebook - add DMI entry for Fujitsu B-2130
Input: ALPS - add signature for Toshiba Satellite Pro M10
Input: elantech - make sure touchpad is really in absolute mode
Input: elantech - provide a workaround for jumpy cursor on firmware 2.34
Input: ucb1400 - use disable_irq_nosync() in irq handler
Input: tsc2007 - use disable_irq_nosync() in irq handler
Input: sa1111ps2 - use disable_irq_nosync() in irq handlers
Input: omap-keypad - use disable_irq_nosync() in irq handler
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In order to utilize the full power of the new multi-touch devices, a
way to report detailed finger data to user space is needed. This patch
adds a multi-touch (MT) protocol which allows drivers to report details
for an arbitrary number of fingers.
The driver sends a SYN_MT_REPORT event via the input_mt_sync() function
when a complete finger has been reported.
In order to stay compatible with existing applications, the data
reported in a finger packet must not be recognized as single-touch
events. In addition, all finger data must bypass input filtering,
since subsequent events of the same type refer to different fingers.
A set of ABS_MT events with the desired properties are defined. The
events are divided into categories, to allow for partial implementation.
The minimum set consists of ABS_MT_TOUCH_MAJOR, ABS_MT_POSITION_X and
ABS_MT_POSITION_Y, which allows for multiple fingers to be tracked.
If the device supports it, the ABS_MT_WIDTH_MAJOR may be used to provide
the size of the approaching finger. Anisotropy and direction may be
specified with ABS_MT_TOUCH_MINOR, ABS_MT_WIDTH_MINOR and
ABS_MT_ORIENTATION. Devices with more granular information may specify
general shapes as blobs, i.e., as a sequence of rectangular shapes
grouped together by a ABS_MT_BLOB_ID. Finally, the ABS_MT_TOOL_TYPE
may be used to specify whether the touching tool is a finger or a pen.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With the upcoming multi-touch interface as an example, there is
a need to make certain that all reported events actually get passed
to the event handler. This patch equips the input core with the
ability to bypass all filtering for certain EV_ABS events.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for the new unibody Macbook, with physically
integrated button and trackpad. Since the integrated button changes
the logic for touch-and-click, a device capability bit mask is now
reported in input_id.version, which can be picked up by user space
via a EVIOCGID call.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: David M. Lary <dmlary@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The integrated button on the new unibody Macbooks presents a need to
report explicit four-finger actions. Evidently, the finger pressing
the button is also touching the trackpad, so in order to fully support
three-finger actions, the driver must be able to report four-finger
actions. This patch adds a new button, BTN_TOOL_QUADTAP, which
achieves this.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The new unibody Macbooks are equipped with an integrated button and
trackpad. The package header of the trackpad interface has changed to
also contain information about the integrated button. This patch
performs the necessary preparations to allow for the new package
header.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_DMA_API_DEBUG spotted an instance of appletouch using
an array on the stack as a DMA buffer for certain hardware.
Change it to use a kmalloc()ed buffer instead.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixed a bug that was introduced in kernel 2.6.28 for
TabletPC touch data. The wacom_parse_hid routine in wacom_sys.c
should always return 0 even when usb_control_msg got an error.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Although we already have entry for ZEPHYR the match is done
on product name whereas B-2130 BIOS has it in board name.
Reported-by: Yuriy Zhuravlev <stalkerg@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This toshiba has a touchpad with trackpoint and 2 sets of left
and right buttons (above and below touchpad).
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
