This fixes an crash when empty bond device is added to a bridge.
If an interface with invalid ethernet address (all zero) is added
to a bridge, then bridge code detects it when setting up the forward
databas entry. But the error unwind is broken, the bridge port object
can get freed twice: once when ref count went to zeo, and once by kfree.
Since object is never really accessible, just free it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've hit an issue on my system when I've been using RealTek RTL8139D cards in
bonding interface in mode balancing-alb. When I enslave a card, the current
active slave (bond->curr_active_slave) is not set and the link is therefore
not functional.
----
# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
Bonding Mode: adaptive load balancing
Primary Slave: None
Currently Active Slave: None
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:1f:1f:01:2f:22
----
The thing that gets it right is when I unplug the cable and then I put it back
into the NIC. Then the current active slave is set to eth1 and link is working
just fine. Here is dmesg log with bonding DEBUG messages turned on:
----
ADDRCONF(NETDEV_UP): bond0: link is not ready
event_dev: bond0, event: 1
IFF_MASTER
event_dev: bond0, event: 8
IFF_MASTER
bond_ioctl: master=bond0, cmd=35216
slave_dev=cac5d800:
slave_dev->name=eth1:
eth1: ! NETIF_F_VLAN_CHALLENGED
event_dev: eth1, event: 8
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 1
event_dev: eth1, event: 8
IFF_SLAVE
Initial state of slave_dev is BOND_LINK_UP
bonding: bond0: enslaving eth1 as an active interface with an up link.
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
event_dev: bond0, event: 4
IFF_MASTER
bond0: no IPv6 routers present
<<<<cable unplug>>>>
eth1: link down
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely down for interface eth1, disabling it
event_dev: bond0, event: 4
IFF_MASTER
<<<<cable plug>>>>
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely up for interface eth1.
bonding: bond0: making interface eth1 the new active one.
event_dev: eth1, event: 8
IFF_SLAVE
event_dev: eth1, event: 8
IFF_SLAVE
bonding: bond0: first active interface up!
event_dev: bond0, event: 4
IFF_MASTER
----
The current active slave is set by calling bond_select_active_slave() function
from bond_miimon_commit() function when the slave (eth1) link goes to state up.
I also tested this on other machine with Broadcom NetXtreme II BCM5708
1000Base-T NIC and there all works fine. The thing is that this adapter is down
and goes up after few seconds after it is enslaved.
This patch calls bond_select_active_slave() in bond_enslave() function for modes
alb and tlb and makes sure that the current active slave is set up properly even
when the slave state is already up. Tested on both systems, works fine.
Notice: The same problem can maybe also occrur in mode 8023AD but I'm unable to
test that.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gianfar uses a hardware header FCB for offloading. However when used
with bridging or IP forwarding, TX skb might not have enough headroom
for the FCB. Reallocate skb for such cases.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch bumps the driver release date to March 25th 2009
and release version to 0.22.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the second PHY address which is strapped
to be at PHY address 3 instead of 2.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: cleanup
Add /** style comments around find_busiest_group(). Also add a few
explanatory comments.
This concludes the find_busiest_group() cleanup. The function is
now down to 72 lines from the original 313 lines.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Balbir Singh" <balbir@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: "Dhaval Giani" <dhaval@linux.vnet.ibm.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: "Vaidyanathan Srinivasan" <svaidy@linux.vnet.ibm.com>
LKML-Reference: <20090325091427.13992.18933.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Create seperate helper functions to initialize the
power-savings-balance related variables, to update them and
to check if we have a scope for performing power-savings balance.
Add no-op inline functions for the !(CONFIG_SCHED_MC || CONFIG_SCHED_SMT)
case.
This will eliminate all the #ifdef jungle in find_busiest_group() and the
other helper functions.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Balbir Singh" <balbir@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: "Dhaval Giani" <dhaval@linux.vnet.ibm.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: "Vaidyanathan Srinivasan" <svaidy@linux.vnet.ibm.com>
LKML-Reference: <20090325091422.13992.73616.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, micro-optimization
We don't need to perform power_savings balance if either the
cpu is NOT_IDLE or if the sched_domain doesn't contain the
SD_POWERSAVINGS_BALANCE flag set.
Currently, we check for these conditions multiple number of
times, even though these variables don't change over the scope
of find_busiest_group().
Check once, and store the value in the already exiting
"power_savings_balance" variable.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Balbir Singh" <balbir@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: "Dhaval Giani" <dhaval@linux.vnet.ibm.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: "Vaidyanathan Srinivasan" <svaidy@linux.vnet.ibm.com>
LKML-Reference: <20090325091417.13992.2657.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move all the imbalance calculation out of find_busiest_group()
through this helper function.
With this change, the structure of find_busiest_group() will be
as follows:
- update_sched_domain_statistics.
- check if imbalance exits.
- update imbalance and return busiest.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Balbir Singh" <balbir@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: "Dhaval Giani" <dhaval@linux.vnet.ibm.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: "Vaidyanathan Srinivasan" <svaidy@linux.vnet.ibm.com>
LKML-Reference: <20090325091411.13992.43293.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
We have two places in find_busiest_group() where we need to calculate
the minor imbalance before returning the busiest group. Encapsulate
this functionality into a seperate helper function.
Credit: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Balbir Singh" <balbir@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: "Dhaval Giani" <dhaval@linux.vnet.ibm.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
LKML-Reference: <20090325091406.13992.54316.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Create a helper function named update_sd_lb_stats() to update the
various sched_domain related statistics in find_busiest_group().
With this we would have moved all the statistics computation out of
find_busiest_group().
Credit: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Balbir Singh" <balbir@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: "Dhaval Giani" <dhaval@linux.vnet.ibm.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
LKML-Reference: <20090325091401.13992.88737.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Currently we use a lot of local variables in find_busiest_group()
to capture the various statistics related to the sched_domain.
Group them together into a single data structure.
This will help us to offload the job of updating the sched_domain
statistics to a helper function.
Credit: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Balbir Singh" <balbir@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: "Dhaval Giani" <dhaval@linux.vnet.ibm.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
LKML-Reference: <20090325091356.13992.25970.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Create a helper function named update_sg_lb_stats() which
can be invoked to calculate the individual group's statistics
in find_busiest_group().
This reduces the lenght of find_busiest_group() considerably.
Credit: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Aked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Balbir Singh" <balbir@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: "Dhaval Giani" <dhaval@linux.vnet.ibm.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
LKML-Reference: <20090325091351.13992.43461.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Currently a whole bunch of variables are used to store the
various statistics pertaining to the groups we iterate over
in find_busiest_group().
Group them together in a single data structure and add
appropriate comments.
This will be useful later on when we create helper functions
to calculate the sched_group statistics.
Credit: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Balbir Singh" <balbir@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: "Dhaval Giani" <dhaval@linux.vnet.ibm.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
LKML-Reference: <20090325091345.13992.20099.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Some indentations in find_busiest_group() can minimized by using
early exits with the help of gotos. This improves readability in
a couple of cases.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Balbir Singh" <balbir@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: "Dhaval Giani" <dhaval@linux.vnet.ibm.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: "Vaidyanathan Srinivasan" <svaidy@linux.vnet.ibm.com>
LKML-Reference: <20090325091340.13992.45062.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Currently the load idx calculation code is in find_busiest_group().
Move that to a static inline helper function.
Similary, to find the first cpu of a sched_group we use
cpumask_first(sched_group_cpus(group))
Use a helper to that. It improves readability in some cases.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Balbir Singh" <balbir@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: "Dhaval Giani" <dhaval@linux.vnet.ibm.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: "Vaidyanathan Srinivasan" <svaidy@linux.vnet.ibm.com>
LKML-Reference: <20090325091335.13992.55424.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change the start function in preparation of the generic watchdog code.
Also make sure that locking of the start function is OK.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Change the wdt.c watchdog driver so that the code is the same for
both the WDT500 as the WDT501-P card. The selection of the card
is now being done via the module parameter: 'type' instead of the
config option CONFIG_WDT_501.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix following includes:
* #include <asm/io.h> should be #include <linux/io.h>
* #include <asm/uaccess.h> should be #include <linux/uaccess.h>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add the PCI-ID for the upcoming new BMC controller for HP hardware.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The orion5x-wdt driver is now registered as a platform device and
receives the tclk value as platform data. This fixes a compile issue
cause by a previously removed define "ORION5X_TCLK".
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Kristof Provost <kristof@sigsegv.be>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Sylver Bruneau <sylver.bruneau@googlemail.com>
Cc: Kunihiko IMAI <bak@d2.dion.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make sure that the watchdog is not running after loading
and before it is started by opening /dev/watchdog.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDT timer ticks quite fast (half of the CPU clock speed, which may
be between 198MHz and 330MHz (or 400MHz on newer boards)). Given it's
size of 32Bit, the maximum timeout value ranges from about 21s to 43s,
depending on the configured CPU clock speed.
This patch add's the timeout module parameter and checks that it's not
bigger then the maximum timeout for the given clock speed.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Clean-up the rc32434 driver code:
- name the platform driver rc32434_wdt_driver
- Replace KBUILD_MODNAME ": " with PFX define.
- Cleanup include files
- Order the ioctl's
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove davinci platform-specific IO accessor macros in favor
of standard ioremap + io[read|write]* functions.
Also, convert printk(KERN_ERR ....) into dev_err(...)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I noticed the W83697UG driver tries to register a watchdog even though
it already noticed the chip isn't there.
WDT driver for the Winbond(TM) W83697UG/UF Super I/O chip initialising.
w83697ug/uf WDT: No W83697UG/UF could be found
w83697ug/uf WDT: Watchdog already running. Resetting timeout to 60 sec
w83697ug/uf WDT: cannot register miscdev on minor=130 (err=-16)
Patch propagates the error back to wdt_init().
Signed-off-by: Eric Lammerts <eric@lammerts.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
wait_event_timeout just takes the numnber of jiffies to wait as
an argument. That value does not include jiffies itself.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a recovery is started for a qeth device, additional invocations
to change a mac address, to configure a VLAN interface on top, or to
add multicast addresses should wait till recovery is finished,
otherwise recovery might fail.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth: Unregister MAC addresses from device (layer 2) during
recovery cycle. When the device is set online the MAC
addresses are registered again on the device.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performance measurements showed EDDP does not lower CPU costs but increase
them. So we dump out EDDP code from qeth driver.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics counter for software tx checksumming.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a way to provide the MAC address for ax88796 devices from
their platform data. Boards might decide to set the address
programmatically, taken from boot tags or other sources.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to the ax88796 ethernet driver to take IRQ flags
given by the platform_device definition.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device ID for a new variant of the 82574 adapter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cxgb3 NIC driver can handle more firmware versions than iw_cxgb3,
and since commit 8207befa ("cxgb3: untie strict FW matching") cxgb3
will load with firmware versions that iw_cxgb3 can't handle. The FW
major number indicates a specific interface between the FW and
iw_cxgb3. Thus if the major number of the running firmware does not
match the required version compiled into iw_cxgb3, then iw_cxgb3 must
not register that device.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On a timeout call a device specific handler early in the recovery so that
we can complete and process successful commands which timed out due to IRQ
loss or the like rather more elegantly.
[Revised to exclude the timeout handling on a few devices that inherit from
SFF but are not SFF enough to use the default timeout handler]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ipv6 version of bind_conflict code calls ipv6_rcv_saddr_equal()
which at times wrongly identified intersections between addresses.
It particularly broke down under a few instances and caused erroneous
bind conflicts.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Binding to a v4-mapped address on an AF_INET6 socket should
produce the same result as binding to an IPv4 address on
AF_INET socket. The two are interchangable as v4-mapped
address is really a portability aid.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
