This patch fixes a few obvious bugs in DSP loader stuff:
- Fix possible memory leaks in the error path
- Avoid double-free calls in dma_reset()
- Properly set/unset WC bits for DMA buffers
- Add missing error status checks
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Base the DSP firmware transfer and communication timeouts on jiffy values.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the HD Audio Device IDs for the Intel Wellsburg PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A Haswell test machine showed that the invalid connection list, but
this time it has only a single pin on the codec, thus the former fixup
code doesn't work as it assumes the three pins blindly.
This patch splits the former fixup code to two parts:
- Enable eDP 1.2 for Haswell codec
- Fix the connection list of pins on Haswell codec;
the converter list is recorded dynamically in hdmi_add_cvt(), and
applied in hdmi_add_pin()
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Haswell machines support more than one display outputs (HDMI or DP),
but its BIOS may not enable the codec's 2nd and 3rd pin and output cvt widgets.
This patch implements a board-specific fixup for Intel Haswell Machines:
If the hidden pins are not enabled by BIOS, the driver will enable them
and call common code to update the codec tree.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A codec may allow software to hide some unused pin/cvt widgets.
Sometimes BIOS does not enable the hidden widgets properly although they are
needed for the board. Thus the driver need to enable them as a board-specific
fixup and the whole tree will change.
This patch implements a common code for rereading codec widgets. So the fixup
code can call it after enabling the hidden widgets.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Help avoid noise from the power up of the capture path propagating through
into the start of the recording (especially noise caused by the ramp of
microphone biases) by keeping the capture muted until after we've finished
powering things up with DAPM in the same manner we do for playback. This
allows us to take advantage of soft mute support in the hardware more
effectively and is more consistent.
The core code using the existing digital mute operation is updated to take
advantage of this. Some additional cases in the soc-pcm code and suspend
will need separate handling but these are less practically relevant than
the main runtime stream start/stop case.
Rather than refactor the digital mute function in every single driver a
new operation is added for drivers taking advantage of this functionality,
the old operation should be phased out over time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Currently we set the max number of connections to be 32, but there
seems codec that gives longer connection lists like AD1988, and we see
errors in proc output and else. (Though, in the case of AD1988, it's
a list of all codecs connected to a single vendor widget, so this must
be something fishy, but it's still valid from the h/w design POV.)
This patch tries to remove this restriction. For efficiency, we still
use the fixed size array in the parser, but takes a dynamic array when
the size is reported to be greater than that.
Now the fixed array size is found only in patch_hdmi.c, but it should
be fine, as the codec itself can't support so many pins.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise capture activity on a compressed DAI would mute any playback
on the same DAI.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Fix these two compile errors on s390 which does not have HAS_IOPORT
nor GENERIC_HARDIRQS:
sound/pci/lx6464es/lx6464es.c: In function ‘snd_lx6464es_free’:
sound/pci/lx6464es/lx6464es.c:565:2: error: implicit declaration of function ‘ioport_unmap’
sound/soc/codecs/wm8903.c: In function ‘wm8903_set_pdata_irq_trigger’:
sound/soc/codecs/wm8903.c:1954:9: error: implicit declaration of function ‘irq_get_irq_data’
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch completes the replacement of the existing max98090 driver,
by installing a more complete driver.
Signed-off-by: Jerry Wong <jerry.wong@maximintegrated.com>
Tested-by: Matthew Mowdy <matthew.mowdy@maximintegrated.com>
Reviewed-by: Ralph Birt <ralph.birt@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch removes the existing max98090 driver prior to installing a more
complete one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sound/pci/hda/patch_ca0132.c: In function ‘ca0132_is_vnode_effective’:
sound/pci/hda/patch_ca0132.c:3331:15: warning: ‘nid’ may be used uninitialized in this function [-Wmaybe-uninitialized]
sound/pci/hda/patch_ca0132.c:4345:13: warning: ‘ca0132_download_dsp’ defined but not used [-Wunused-function]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The loopback list is referred by the VIA codec driver no matter
whether CONFIG_PM is set or not, thus we need to enable it always.
Otherwise it gets compile errors.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The wm->regs[] array has WM8766_REG_COUNT (16) elements not
WM8766_REG_RESET (31).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's mostly harmless to apply it for new models even if they have no
mic mute LED (just toggling an unused GPIO pin).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9hz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
The ASoC compressed API did not implement the copy callback in its
compressed ops which is required for DSPs that are not memory mapped.
This patch creates a local copy of the compress ops for each runtime and
modifies them with a copy callback as appropriate.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The same constraint is going to be set in the snd_dmaengine_pcm_open()
function, so there is no need to set it here as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These days, GUIs such as Gnome sound settings want to be able to
show the correct jack status even when no streams are currently
running. I doubt this gives any measurable difference in power,
but if it does, the "Jack Detect" control can still be used to
turn polling off.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The VT1708 has no unsol event capability, and polling is set using
the "Jack Detect" alsamixer control. In order not to create
phantom Jack controls, temporary enable jackpoll during build_controls.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
