this will fix crash bug when doing rmmod to the driver, this is because the
port_stop function get called later and it could access the device's registers.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this fixes crash bug as the iomap table is not valid for integrated controllers.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sata_mv driver can be loaded as a platform device, as is done by
various Orion (ARM) based devices. The driver needs to define a module
alias for the platform driver so udev will load it automatically.
Tested with Debian on a QNAP TS-209.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
that provided by the block layer
ATA requires that all DMA transfers begin and end on word boundaries.
Because of this, a large amount of machinery grew up in ide to adjust
scatterlists on this basis. However, as of 2.5, the block layer has a
dma_alignment variable which ensures both the beginning and length of a
DMA transfer are aligned on the dma_alignment boundary. Although the
block layer does adjust the beginning of the transfer to ensure this
happens, it doesn't actually adjust the length, it merely makes sure
that space is allocated for transfers beyond the declared length. The
upshot of this is that scatterlists may be padded to any size between
the actual length and the length adjusted to the dma_alignment safely
knowing that memory is allocated in this region.
Right at the moment, SCSI takes the default dma_aligment which is on a
512 byte boundary. Note that this aligment only applies to transfers
coming in from user space. However, since all kernel allocations are
automatically aligned on a minimum of 32 byte boundaries, it is safe to
adjust them in this manner as well.
tj: * Adjusting sg after padding is done in block layer. Make libata
set queue alignment correctly for ATAPI devices and drop broken
sg mangling from ata_sg_setup().
* Use request->raw_data_len for ATAPI transfer chunk size.
* Killed qc->raw_nbytes.
* Separated out killing qc->n_iter.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
pp is never used again in this function, no need to declare a
new one.
drivers/ata/sata_mv.c:1545:24: warning: symbol 'pp' shadows an earlier one
drivers/ata/sata_mv.c:1501:22: originally declared here
drivers/ata/sata_mv.c:1553:24: warning: symbol 'pp' shadows an earlier one
drivers/ata/sata_mv.c:1501:22: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When the sata_mv driver is used as a platform driver,
mv_create_dma_pools() is never called so it fails when trying
to alloc in mv_pool_start().
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
mips:
drivers/ata/sata_mv.c: In function `mv_port_free_dma_mem':
drivers/ata/sata_mv.c:1080: error: implicit declaration of function `dma_pool_free'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Marvell's Orion SoC includes SATA controllers based on Marvell's
PCI-to-SATA 88SX controllers. This patch extends the libATA sata_mv
driver to support those controllers.
[edited to use linux/ata_platform.h -jg]
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The integrated SATA controller is connected directly to the SoC's
internal bus, not via PCI interface. this patch removes the dependency
on the PCI interface.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove some obsolete comments, and bump up the driver version number.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver currently has no need for the .post_internal_cmd op.
So get rid of it, to save unnecessary transitions between EDMA and non-EDMA modes.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Final changes to actually turn on NCQ in the driver for GEN_II/IIE hardware.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In preparation for supporting NCQ, we must allocate separate SG tables
for each command tag, rather than just a single table per port as before.
Gen-I hardware cannot do NCQ, though, so we still allocate just a single
table for that, but populate it in all 32 slots to avoid special-cases
elsewhere in hotter paths of the code.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Create host-owned DMA memory pools, for use in allocating/freeing per-port
command/response queues and SG tables. This gives us a way to guarantee we
meet the hardware address alignment requirements, and also reduces memory that
might otherwise be wasted on alignment gaps.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The GenII chips have only 8-bits for the sector_count field when performing NCQ.
Add a dev_config method to restrict this when necessary, taking care not to
override any other restriction already in place (likely none, but someday.. ?).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify tag handling by using the cid/hqtag field instead of ioid,
as recommended by Marvell.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
An extra EDMA config bit is required for NCQ operation.
So set/clear it as needed, and cache current setting in port_priv.
For now though, it will always be "off" (0).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify and fix EDMA configuration setup to match Marvell specificiations.
The chip documentation gives a specific (re)init sequence, which we now follow.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use naming consistent with elsewhere in this driver.
This will keep things less confusing when we later add "hc_mmio" in this function.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The chips can handle many transient errors internally without a software IRQ.
We now mask/ignore those interrupts here. This is necessary for NCQ, later on.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A hard reset is necessary after hotplug events.
Only clear the error irq bits that were set on entry.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata used private sg iterator to handle padding sg. Now that sg can
be chained, padding can be handled using standard sg ops. Convert to
chained sg.
* s/qc->__sg/qc->sg/
* s/qc->pad_sgent/qc->extra_sg[]/. Because chaining consumes one sg
entry. There need to be two extra sg entries. The renaming is also
for future addition of other extra sg entries.
* Padding setup is moved into ata_sg_setup_extra() which is organized
in a way that future addition of other extra sg entries is easy.
* qc->orig_n_elem is unused and removed.
* qc->n_elem now contains the number of sg entries that LLDs should
map. qc->mapped_n_elem is added to carry the original number of
mapped sgs for unmapping.
* The last sg of the original sg list is used to chain to extra sg
list. The original last sg is pointed to by qc->last_sg and the
content is stored in qc->saved_last_sg. It's restored during
ata_sg_clean().
* All sg walking code has been updated. Unnecessary assertions and
checks for conditions the core layer already guarantees are removed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve the existing boot/load time warnings from sata_mv
for Highpoint RocketRAID 23xx cards, based on new knowledge
about where the BIOS likes to overwrite sectors with metadata.
Harmless to us, but very useful for end users.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Highpoint RocketRAID boards using Marvell 7042 chips
overwrite the 9th sector of attached drives at boot time,
when those drives are configured as "Legacy" (the default)
in the HighPoint BIOS.
This kills GRUB, and probably other stuff.
But it all happens *before* Linux is even loaded.
So, for now we'll log a WARNING when such boards are detected,
and advise users to configure BIOS "JBOD" volumes instead,
which don't appear to suffer from this problem.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_mv: Fix broken Marvell 7042 support.
The Marvell 7042 chip is more or less the same as the 6042 internally,
but sports a PCIe bus. Despite having identical SATA cores, the 7042
does differ from its PCI bus counterparts in placment and layout of
certain bus related registers.
This patch fixes sata_mv to distinguish between the PCI bus registers
of earlier chips, and the PCIe bus registers of the 7042.
Specifically, move the offsets and bit patterns for the
PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv,
as these values differ between the 6xxx and 7xxx series chips.
This fixes the driver to not access reserved PCI addresses,
and prevents the lockups reported in linux-2.6.24 with 7042 boards.
Also add a new PCI ID for the Highpoint 2300 7042-based board
that I'm using for testing this stuff here.
Tested with Marvell 6081 + 7042 chips, on x86 & x86_64.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tackle the relatively sane complaints of checkpatch --file.
The vast majority is indentation and whitespace changes, the rest are
* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Short term, this works around a bug introduced by early sg-chaining
work.
Long term, removing this function eliminates a branch from a hot
path loop in each scatter/gather table build. Also, as this code
demonstrates, we don't need to _track_ the end of the s/g list, as
long as we mark it in some way. And doing so programatically is nice.
So its a useful cleanup, regardless of its short term effects.
Based conceptually on a quick patch by Jens Axboe.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make ata_dev_try_classify() take a pointer to ata_device instead of
ata_port/port_number combination for consistency and add @present
argument. @present indicates whether the device seems present during
reset. It's the result of TF access during softreset and link
onlineness during hardreset. @present will be used to improve
diagnostic failure handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, port configuration reporting has the following problems.
* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.
This patch implements and uses ata_port_desc() and
ata_port_pbar_desc(). ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ". ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.
LLD pushes whatever description it wants using the above two
functions. The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".
SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions. In many cases,
such controllers need to report different things anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following PHY-related functions to deal with ata_link instead
of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* corruption fix: we only want the lower 16 bits of length (0 == 64kb)
* ditto: the upper layer sets max-phys-segments to LIBATA_MAX_PRD,
so we must reset it to own hw-specific length.
* delete unused mv_fill_sg() return value
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The recent mv_fill_sg() rewrite, to fix a data corruption problem
related to IOMMU virtual merging, forgot to account for the
potentially-increased size of the scatter/gather table after its run.
Additionally, the DMA boundary is reduced from 0xffffffff to 0xffff
to more closely match the needs of mv_fill_sg().
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in sata_mv for cases where the IOMMU layer has merged SG entries
to larger than 64KB. They need to be split up before being sent to
the driver.
Just for simplicity's sake, split up at 64K boundary instead of 64K size,
since that's what the common code does anyway.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Underneath all the HPT packaging, PCI identifiers, binary driver modules
and stuff you find that ...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert ->scr_read/write callbacks to return error code to better
indicate failure. This will help handling of SCR_NOTIFICATION.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Requiring LLDs to format multiple error description messages properly
doesn't work too well. Help LLDs a bit by making ata_ehi_push_desc()
insert ", " on each invocation. __ata_ehi_push_desc() is the raw
version without the automatic separator.
While at it, make ehi_desc interface proper functions instead of
macros.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* trim trailing whitespace
* document some flags, registers, and register bits
* fix locking around EDMA on/off and configuration
* continue replacing "constant OP var" with "var OP constant"
* use new pci_try_set_mwi()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
Due to a mistake in test logic, Gen-IIE chips were being treated as
Gen-II chips in some cases. Fix this, and in the process, clean up
IS_50XX/IS_60XX tests to the more uniform IS_GEN_{I,II,IIE} tests.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
