The PPC405 hard core is used in both the Virtex-II Pro and Virtex 4 FX
FPGAs. This patch cleans up the Virtex naming convention to reflect more
than just the Virtex-II Pro.
Rename files virtex-ii_pro.[ch] to virtex.[ch]
Rename config value VIRTEX_II_PRO to XILINX_VIRTEX
Signed-off-by: Grant C. Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xparameters should not be needed by anything but virtex platform code.
Move it from include/asm-ppc/ to platforms/4xx/xparameters/
This is preparing for work to remove xparameters from the dependancy tree
for most c files. xparam changes should not cause a recompile of the world.
Instead, drivers should get device info from the platform bus (populated
by the boot code)
Signed-off-by: Grant C. Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The last two 8MB TLB entries are being incorrectly set by initial_mmu on 8xx.
The first entry is written with the same virtual/physical address, which
renders it invalid:
BDI>rms 792 0x00001e00
BDI>rms 824 1
BDI>rds 824
SPR 824 : 0xc08000c0 -1065353024
BDI>rds 825
SPR 825 : 0xc0800de0 -1065349664
BDI>rds 826
SPR 826 : 0x00000000 0
And the second entry, in addition, does not have its TLB index set
correctly.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We shouldn't expose the hardware register contents in platform_data.
The only things we allow the user to configure are autoneg, speed, and
duplex. Add specific platform_data fields for these values and remove
the registers configs.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Enable mv643xx_eth driver to work when built as a module on
mv64x60-based embedded systems.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implemented more correct way to support physmapped flash on m8xx
than map in mtd.
The areas intended to contain bootloader are protected readonly.
Note that CFI and JEDEC stuff should be configured properly in order
this to work, e.g. for 885/86x CFI should support 4-chip flash interleave.
Also fixed compilation warning.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch generalizes PPC44x_PIN_SIZE by changing it to
PPC_PIN_SIZE, which can be defined by any sub-arch to automatically adjust
VMALLOC_START.
Define PPC_PIN_SIZE on 8xx, avoiding potential conflicts with the
pinned space.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds setbitsXX/clrbitsXX macro for read-modify-write operations
and converts the 8xx core and drivers to use them.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When I removed the powermac support from arch/ppc/kernel/pci.c,
I overlooked the fact that that file is used in 32-bit ARCH=powerpc
builds. To prevent problems in future, restore the original version
of that file as arch/powerpc/kernel/pci_32.c, and use that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes it possible to build kernels for PReP and/or CHRP
with ARCH=ppc by removing the (non-building) powermac support.
It's now also possible to select PReP and CHRP independently.
Powermac users should now build with ARCH=powerpc instead of
ARCH=ppc. (This does mean that it is no longer possible to
build a 32-bit kernel for a G5.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
tmp_buf_sem sems to be a common name for something completely unused...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> ("usb portion")
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The arch/powerpc version of process.c exports get_wchan itself. When
I moved ARCH=ppc over to using arch/powerpc/kernel/process.c the
get_wchan export in arch/ppc/kernel/ppc_ksyms.c became redundant, so
remove it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 9871166ad692121d6b944159ef3f053570158ea8 commit)
The following implements support for instantiation of 8MB D-TLB
entries for the kernel direct virtual mapping on 8xx, thus reducing TLB
space consumed for the kernel.
Test used: writing 40MB from /dev/zero to file in ext2fs over
RAMDISK.
$ time dd if=/dev/zero of=file bs=4k count=10000
VANILLA 8MB kernel data pages
real 0m11.485s real 0m11.267s
user 0m0.218s user 0m0.250s
sys 0m8.939s sys 0m9.108s
real 0m11.518s real 0m10.978s
user 0m0.203s user 0m0.222s
sys 0m9.585s sys 0m9.138s
real 0m11.554s real 0m10.967s
user 0m0.228s user 0m0.222s
sys 0m9.497s sys 0m9.127s
real 0m11.633s real 0m11.286s
user 0m0.214s user 0m0.196s
sys 0m9.529s sys 0m9.134s
and averages for both:
real 11.54750 real 11.12450
Which is a 3.6% improvement in execution time. More improvement is
expected for loads with larger kernel data footprint (real workloads).
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The gianfar driver changed how it required MDIO bus and phy id's
to be passed to it. Also, it no longer passes the physical address
of the MDIO bus. Instead we have a proper platform device.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
in amigahw.h custom renamed to amiga_custom, in drivers with few instances the
same replacement, in the rest - #define custom amiga_custom in driver itself
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Ingo Molnar <mingo@elte.hu>
This is the latest version of the scheduler cache-hot-auto-tune patch.
The first problem was that detection time scaled with O(N^2), which is
unacceptable on larger SMP and NUMA systems. To solve this:
- I've added a 'domain distance' function, which is used to cache
measurement results. Each distance is only measured once. This means
that e.g. on NUMA distances of 0, 1 and 2 might be measured, on HT
distances 0 and 1, and on SMP distance 0 is measured. The code walks
the domain tree to determine the distance, so it automatically follows
whatever hierarchy an architecture sets up. This cuts down on the boot
time significantly and removes the O(N^2) limit. The only assumption
is that migration costs can be expressed as a function of domain
distance - this covers the overwhelming majority of existing systems,
and is a good guess even for more assymetric systems.
[ People hacking systems that have assymetries that break this
assumption (e.g. different CPU speeds) should experiment a bit with
the cpu_distance() function. Adding a ->migration_distance factor to
the domain structure would be one possible solution - but lets first
see the problem systems, if they exist at all. Lets not overdesign. ]
Another problem was that only a single cache-size was used for measuring
the cost of migration, and most architectures didnt set that variable
up. Furthermore, a single cache-size does not fit NUMA hierarchies with
L3 caches and does not fit HT setups, where different CPUs will often
have different 'effective cache sizes'. To solve this problem:
- Instead of relying on a single cache-size provided by the platform and
sticking to it, the code now auto-detects the 'effective migration
cost' between two measured CPUs, via iterating through a wide range of
cachesizes. The code searches for the maximum migration cost, which
occurs when the working set of the test-workload falls just below the
'effective cache size'. I.e. real-life optimized search is done for
the maximum migration cost, between two real CPUs.
This, amongst other things, has the positive effect hat if e.g. two
CPUs share a L2/L3 cache, a different (and accurate) migration cost
will be found than between two CPUs on the same system that dont share
any caches.
(The reliable measurement of migration costs is tricky - see the source
for details.)
Furthermore i've added various boot-time options to override/tune
migration behavior.
Firstly, there's a blanket override for autodetection:
migration_cost=1000,2000,3000
will override the depth 0/1/2 values with 1msec/2msec/3msec values.
Secondly, there's a global factor that can be used to increase (or
decrease) the autodetected values:
migration_factor=120
will increase the autodetected values by 20%. This option is useful to
tune things in a workload-dependent way - e.g. if a workload is
cache-insensitive then CPU utilization can be maximized by specifying
migration_factor=0.
I've tested the autodetection code quite extensively on x86, on 3
P3/Xeon/2MB, and the autodetected values look pretty good:
Dual Celeron (128K L2 cache):
---------------------
migration cost matrix (max_cache_size: 131072, cpu: 467 MHz):
---------------------
[00] [01]
[00]: - 1.7(1)
[01]: 1.7(1) -
---------------------
cacheflush times [2]: 0.0 (0) 1.7 (1784008)
---------------------
Here the slow memory subsystem dominates system performance, and even
though caches are small, the migration cost is 1.7 msecs.
Dual HT P4 (512K L2 cache):
---------------------
migration cost matrix (max_cache_size: 524288, cpu: 2379 MHz):
---------------------
[00] [01] [02] [03]
[00]: - 0.4(1) 0.0(0) 0.4(1)
[01]: 0.4(1) - 0.4(1) 0.0(0)
[02]: 0.0(0) 0.4(1) - 0.4(1)
[03]: 0.4(1) 0.0(0) 0.4(1) -
---------------------
cacheflush times [2]: 0.0 (33900) 0.4 (448514)
---------------------
Here it can be seen that there is no migration cost between two HT
siblings (CPU#0/2 and CPU#1/3 are separate physical CPUs). A fast memory
system makes inter-physical-CPU migration pretty cheap: 0.4 msecs.
8-way P3/Xeon [2MB L2 cache]:
---------------------
migration cost matrix (max_cache_size: 2097152, cpu: 700 MHz):
---------------------
[00] [01] [02] [03] [04] [05] [06] [07]
[00]: - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[01]: 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[02]: 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[03]: 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[04]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1)
[05]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1)
[06]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1)
[07]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) -
---------------------
cacheflush times [2]: 0.0 (0) 19.2 (19281756)
---------------------
This one has huge caches and a relatively slow memory subsystem - so the
migration cost is 19 msecs.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: <wilder@us.ibm.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 5388fb1025 made signal_32.c
use discard_lazy_cpu_state, which broke ARCH=ppc because that
uses the common signal_32.c but has its own process.c. Make ARCH=ppc
use the common process.c to fix this and to reduce the amount
of duplicated code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated Kconfig & Makefiles in prep for adding support for the Freescale
MPC83xx family of processors to arch/powerpc. Moved around some config
options that are more globally applicable to other PowerPC processors.
Added a temporary config option (83xx) to match existing arch/ppc support
for the MPC83xx line.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- In case of system crash, current state of cpu registers is saved in memory
in elf note format. So far memory for storing elf notes was being allocated
statically for NR_CPUS.
- This patch introduces dynamic allocation of memory for storing elf notes.
It uses alloc_percpu() interface. This should lead to better memory usage.
- Introduced based on Andi Kleen's and Eric W. Biederman's suggestions.
- This patch also moves memory allocation for elf notes from architecture
dependent portion to architecture independent portion. Now crash_notes is
architecture independent. The whole idea is that size of memory to be
allocated per cpu (MAX_NOTE_BYTES) can be architecture dependent and
allocation of this memory can be architecture independent.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.14, we had the following definition of _GLOBAL() in
include/asm-ppc/processor.h:
#define _GLOBAL(n)\
.stabs __stringify(n:F-1),N_FUN,0,0,n;\
.globl n;\
n:
In 2.6.15, as part of the great powerpc merge, we moved this definition to
include/asm-powerpc/ppc_asm.h, where it appears (to 32-bit code) as:
#define _GLOBAL(n) \
.text; \
.stabs __stringify(n:F-1),N_FUN,0,0,n;\
.globl n; \
n:
Mostly, this is fine. However, we also have the following, in
arch/ppc/boot/common/util.S:
.section ".relocate_code","xa"
[...]
_GLOBAL(flush_instruction_cache)
[...]
_GLOBAL(flush_data_cache)
[...]
The addition of the .text section definition in the definition of
_GLOBAL overrides the .relocate_code section definition. As a result,
these two functions don't end up in .relocate_code, so they don't get
relocated correctly, and the boot fails.
There's another suspicious-looking usage at kernel/swsusp.S:37 that
someone should look into. I did not exhaustively search the source
tree, though.
The following is the minimal patch that fixes the immediate problem.
I could easily be convinced that the _GLOBAL definition should be
modified to remove the ".text;" line either instead of, or in addition
to, this fix.
Signed-off-by: Paul Janzen <pcj@linux.sez.to>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Configurable 16-bit UID and friends support
This allows turning off the legacy 16 bit UID interfaces on embedded platforms.
text data bss dec hex filename
3330172 529036 190556 4049764 3dcb64 vmlinux-baseline
3328268 529040 190556 4047864 3dc3f8 vmlinux
From: Adrian Bunk <bunk@stusta.de>
UID16 was accidentially disabled for !EMBEDDED.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pci_address_to_pio is missing a closing curly brace
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes pci_address_to_pio() to return an unsigned long (to be safe)
and fixes a bug in the implementation that caused it to return a bogus
IO port number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added the ability to determine if an outbound window in the PCI host
controller is for prefetchable memory and report it as such.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for the TQ Components TQM85xx modules. Currently the
modules TQM8540/8541/8555/8560 are supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the OF address parsers to return the IO flags
indicating the type of address obtained. It also adds a PCI
call for converting physical addresses that hit IO space into
into IO tokens, and add routines that return the translated
addresses into struct resource
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes ARCH=ppc build in your powerpc tree again, with the new
syscall entry/exit path.
Still doesn't actually boot on my Pegasos; the last thing I see is
'MMU:exit'. But at least it builds -- I'll look at why it doesn't boot
later, so that I can see if the mv643xx_eth actually works with ARCH=ppc
(it doesn't with ARCH=powerpc; two in every three packets I receive are
offset by 4 bytes).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates m8xx_wdt as follows:
1) Remove now obsolete fpos check in the write() function. The driver is
currently non functional due to this bug.
2) Use in/out macros for register access.
3) Allows m8xx_wdt to use a kernel timer instead of the builtin RTC/PIT
for keep-alive trigger (which is responsible for servicing the watchdog
until an userspace application takes over). For instance Cyclades PRxK
boards (MPC 855T based) have a non-functional internal RTC/PIT unit.
Behaviour for boards with RTC/PIT is unchaged.
4) The last change required moving the RTCSC register setting code
to a weak function which can be overriden by board specific files.
Otherwise the timer init code trashes the register making it impossible
for m8xx_wdt to detect the situation.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Sam Ravnborg pointed out that calling if_changed was redundant in the
rule since a prerequisite had to have changed for us to get there.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.
For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the discovery of legacy serial ports to a separate file,
makes it common to ppc32 and ppc64, and reworks it to use the new OF
address translators to get to the ports early. This new version can also
detect some PCI serial cards using legacy chips and will probably match
those discovered port with the default console choice.
Only ppc64 gets udbg still yet, unifying udbg isn't finished yet.
It also adds some speed-probing code to udbg so that the default console
can come up at the same speed it was set to by the firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the current version of the spu file system, used
for driving SPEs on the Cell Broadband Engine.
This release is almost identical to the version for the
2.6.14 kernel posted earlier, which is available as part
of the Cell BE Linux distribution from
http://www.bsc.es/projects/deepcomputing/linuxoncell/.
The first patch provides all the interfaces for running
spu application, but does not have any support for
debugging SPU tasks or for scheduling. Both these
functionalities are added in the subsequent patches.
See Documentation/filesystems/spufs.txt on how to use
spufs.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved 83xx and QUICC Engine interrupt handling code into arch/powerpc
as a precursor of getting 83xx sub-arch building in arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges, to some extent, the PPC32 and PPC64 kexec implementations.
We adopt the PPC32 approach of having ppc_md callbacks for the kexec functions.
The current PPC64 implementation becomes the "default" implementation for PPC64
which platforms can select if they need no special treatment.
I've added these default callbacks to pseries/maple/cell/powermac, this means
iSeries no longer supports kexec - but it never worked anyway.
I've renamed PPC32's machine_kexec_simple to default_machine_kexec, inline with
PPC64. Judging by the comments it might be better named machine_kexec_non_of,
or something, but at the moment it's the only implementation for PPC32 so it's
the "default".
Kexec requires machine_shutdown(), which is in machine_kexec.c on PPC32, but we
already have in setup-common.c on powerpc. All this does is call
ppc_md.nvram_sync, which only powermac implements, so instead make
machine_shutdown a ppc_md member and have it call core99_nvram_sync directly
on powermac.
I've also stuck relocate_kernel.S into misc_32.S for powerpc.
Built for ARCH=ppc, and 32 & 64 bit ARCH=powerpc, with KEXEC=y/n. Booted on
P5 LPAR and successfully kexec'ed.
Should apply on top of 493f25ef40.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the EXPORT_SYMBOL'ed but completely unused variable
ucSystemType and removes the unneeded EXPORT_SYMBOL(_prep_type).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This was causing some ordering problems. Remove the up-front evaluation
and just revaluate the compiler version each time we need it.
(The up-front evaluation was problematic because some architectures modify
the value of $(CC)).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Commit 3e9e7c1d0b (ppc32: cleanup AMCC PPC40x
eval boards to support U-Boot) broke the kernel for ML300 / EP405.
It still compiles as there's a weak definition of the function in
misc-embedded.c, but the kernel crashes as the bd_t fixup isn't performed.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some custom cards might not need PCI, without this patch, compilation fails.
Signed-off-by: Roger Blofeld <blofeldus@yahoo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were counting on the bootloader to init some stuff, like get the bus out of
reset and enable accesses.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch takes care of an errata of the MPC5200 by avoiding 32 bits access
in type 1 configuration accesses. All others accesses are still 32 bits wide.
It also adds some mb() since the simple out_be(...) are not sufficient in
this case.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The mpc52xx_pci_fixup_resources is not only called at init but also when there
is a pci hotplug like when a cardbus card is plugged in. So that function is
needed after init too.
Thanks to Asier Llano Palacios for reporting this.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current iomapping used MBAR_SIZE for the size argument of
io_block_mapping, resulting in a call to setbat with a size argument of 64k
which is invalid.
This patch correct this and maps the whole 0xf0000000->0xffffffff range so
that devices on the local bus are also included in the BAT mapping.
Thanks to Bernhard Kuhn from Metrowerks for pointing this out.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
That file is a left-over of the 'old' OCP model that should have been erased
during the change to platform model but I forgot it ...
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disable declaration of cpu variable in default_idle function when
building non-SMP kernels.
Signed-off-by: Otavio Salvador <otavio@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the not needed anymore "jumbo" member from ocp_func_emac_data.
Jumbo frame support is handled by PPC4xx EMAC driver internally now.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The CPM2 interrupt handler does not return success to the IRQ subsystem, which
causes it to kill the IRQ line after 100,000 interrupts.
Signed-off-by: Edson Seabra <Edson.Seabra@cyclades.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
DMA_MODE_{READ,WRITE} are declared in asm-powerpc/dma.h and their
declarations there match the definitions. Old declarations in
ppc4xx_dma.h are not right anymore (wrong type, to start with).
Killed them, added include of asm/dma.h where needed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ppc32 kernel, when built with CONFIG_SMP and booted on a single CPU
machine, will not properly set smp_tb_synchronized, thus causing
gettimeofday() to not use the HW timebase and to be limited to jiffy
resolution. This, among others, causes unacceptable pauses when launching
X.org.
Signed-Off-By: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code that sets the clock spreading feature of the Intrepid ASIC
must not be run on some machine models or those won't boot. This
fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit da0825fd20, making
it so that if you select CONFIG_PPC_MULTIPLATFORM you get support
for PMAC, PREP and CHRP built in.
The reason for not allowing PMAC, PREP and CHRP to be selected
individually for ARCH=ppc is that there is too much interdependency
between them in the platform support code. For example, CHRP uses
the PMAC nvram code.
Configuring with ARCH=powerpc does allow you to select support for
PMAC and CHRP separately. Support for PREP is not there yet but
should be there soon.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Correctly specify treeboot based image entrypoint. Currently makefile uses
$(ENTRYPOINT) which isn't defined anywhere. Each board port sets
entrypoint-$(CONFIG_BOARD_NAME) instead.
Without this patch I cannot boot Ocotea (PPC440GX eval board) anymore. I
was getting random "OS panic" errors from OpenBIOS for a while, but with
current kernel I get them all the time (probably because image became
bigger).
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The time to wait after deasserting PCI_RST has been counted with incorrect
value - this patch fixes the issue.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently discovered a bug on PPC which causes the floating point
registers to get corrupted when CONFIG_PREEMPT=y.
The problem occurred while running a multi threaded Java application that
does floating point. The problem could be reproduced in anywhere from 2 to
6 hours. With the patch I have included below it ran for over a week
without failure.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Tom Rini <trini@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Export symbol needed to allow MOL to run. This was changed to be inline
in past and forgot to be change here.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges align.c, the result isn't quite what was in ppc64 nor
what was in ppc32 :) It should implement all the functionalities of both
though. Kumar, since you played with that in the past, I suppose you
have some test cases for verifying that it works properly before I dig
out the 601 machine ? :)
Since it's likely that I won't be able to test all scenario, code
inspection is much welcome.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we moved things around in irq.h seq_file became an issue. Fix
warnings related to its usage.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SVRs for MPC8343/E were incorrect and really the SVRs
for MPC8347/E.
Signed-off-by: David Updegraff <dave@cray.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Building ARCH=ppc for multiplatforms with CONFIG_CHRP not set fails
due to some unshielded code in xmon
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The merge of machine types broke boot with yaboot & ARCH=ppc due to the
old code still retreiving the old-syle machine type passed in by yaboot.
This patch fixes it by translating those old numbers. Since that whole
mecanism is deprecated, this is a temporary fix until ARCH=ppc uses the
new prom_init that the merged architecture now uses for both ppc32 and
ppc64 (after 2.6.15)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently 8xx fails to boot due to endless pagefaults.
Seems the bug is exposed by the change which avoids flushing the
TLB when not necessary (in case the pte has not changed), introduced
recently:
__handle_mm_fault():
entry = pte_mkyoung(entry);
if (!pte_same(old_entry, entry)) {
ptep_set_access_flags(vma, address, pte, entry, write_access);
update_mmu_cache(vma, address, entry);
lazy_mmu_prot_update(entry);
} else {
/*
* This is needed only for protection faults but the arch code
* is not yet telling us if this is a protection fault or not.
* This still avoids useless tlb flushes for .text page faults
* with threads.
*/
if (write_access)
flush_tlb_page(vma, address);
}
The "update_mmu_cache()" call was unconditional before, which caused the TLB
to be flushed by:
if (pfn_valid(pfn)) {
struct page *page = pfn_to_page(pfn);
if (!PageReserved(page)
&& !test_bit(PG_arch_1, &page->flags)) {
if (vma->vm_mm == current->active_mm) {
#ifdef CONFIG_8xx
/* On 8xx, cache control instructions (particularly
* "dcbst" from flush_dcache_icache) fault as write
* operation if there is an unpopulated TLB entry
* for the address in question. To workaround that,
* we invalidate the TLB here, thus avoiding dcbst
* misbehaviour.
*/
_tlbie(address);
#endif
__flush_dcache_icache((void *) address);
} else
flush_dcache_icache_page(page);
set_bit(PG_arch_1, &page->flags);
}
Which worked to due to pure luck: PG_arch_1 was always unset before, but
now it isnt.
The root of the problem are the changes against the 8xx TLB handlers introduced
during v2.6. What happens is the TLBMiss handlers load the zeroed pte into
the TLB, causing the TLBError handler to be invoked (thats two TLB faults per
pagefault), which then jumps to the generic MM code to setup the pte.
The bug is that the zeroed TLB is not invalidated (the same reason
for the "dcbst" misbehaviour), resulting in infinite TLBError faults.
The "two exception" approach requires a TLB flush (to nuke the zeroed TLB)
at each PTE update for correct behaviour:
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The MPC8349 PIBs system has a expansion board with 6 PCI slots. We needed
to update the IDSEL interrupt mapping for it to work properly. However,
only PCI1 is supported as the first revision of this expansion board
doesn't function properly for PCI2. For the time being we have zero'd out
the entries for the IDSELs related to PCI2. When a functioning expansion
board exists we can fix the table.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enablement patch for the new PowerBooks (late 2005 edition).
This enables the ATA controller, Gigabit ethernet and basic AGP setup.
Bluetooth works out-of-the box after running hid2hci.
Still remaining is to get the touchpad to work, the simple change of just
adding the new USB ids isn't enough.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changed jobs and the Freescale address is no longer valid.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We needed the VDSO symbols in the arch/ppc asm-offsets.c, and there
were a few usages of _systemcfg still left lying around.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bit position in the status register corresponding to the
PCI DMA interrupt was incorrect. Additionally, we did not
have a define for the PCI DMA interrupt.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the PPC fixup for old NCR 810 controllers to generic quirks -
it's needed for Alpha, x86 and other architectures that use
setup-bus.c.
Thanks to Jay Estabrook for pointing out the issue.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch merges platform codes. systemcfg->platform is no longer used,
systemcfg use in general is deprecated as much as possible (and renamed
_systemcfg before it gets completely moved elsewhere in a future patch),
_machine is now used on ppc64 along as ppc32. Platform codes aren't gone
yet but we are getting a step closer. A bunch of asm code in head[_64].S
is also turned into C code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch consolidates macros used to generate assembly for
compatibility across different CPUs or configs. A new header,
asm-powerpc/asm-compat.h contains the main compatibility macros. It
uses some preprocessor magic to make the macros suitable both for use
in .S files, and in inline asm in .c files. Headers (bitops.h,
uaccess.h, atomic.h, bug.h) which had their own such compatibility
macros are changed to use asm-compat.h.
ppc_asm.h is now for use in .S files *only*, and a #error enforces
that. As such, we're a lot more careless about namespace pollution
here than in asm-compat.h.
While we're at it, this patch adds a call to the PPC405_ERR77 macro in
futex.h which should have had it already, but didn't.
Built and booted on pSeries, Maple and iSeries (ARCH=powerpc). Built
for 32-bit powermac (ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc32 and ppc64 versions of cacheflush.h were almost identical.
The two versions of cache.h are fairly similar, except for a bunch of
register definitions in the ppc32 version which probably belong better
elsewhere. This patch, therefore, merges both headers. Notable
points:
- there are several functions in cacheflush.h which exist only
on ppc32 or only on ppc64. These are handled by #ifdef for now, but
these should probably be consolidated, along with the actual code
behind them later.
- Confusingly, both ppc32 and ppc64 have a
flush_dcache_range(), but they're subtly different: it uses dcbf on
ppc32 and dcbst on ppc64, ppc64 has a flush_inval_dcache_range() which
uses dcbf. These too should be merged and consolidated later.
- Also flush_dcache_range() was defined in cacheflush.h on
ppc64, and in cache.h on ppc32. In the merged version it's in
cacheflush.h
- On ppc32 flush_icache_range() is a normal function from
misc.S. On ppc64, it was wrapper, testing a feature bit before
calling __flush_icache_range() which does the actual flush. This
patch takes the ppc64 approach, which amounts to no change on ppc32,
since CPU_FTR_COHERENT_ICACHE will never be set there, but does mean
renaming flush_icache_range() to __flush_icache_range() in
arch/ppc/kernel/misc.S and arch/powerpc/kernel/misc_32.S
- The PReP register info from asm-ppc/cache.h has moved to
arch/ppc/platforms/prep_setup.c
- The 8xx register info from asm-ppc/cache.h has moved to a
new asm-powerpc/reg_8xx.h, included from reg.h
- flush_dcache_all() was defined on ppc32 (only), but was
never called (although it was exported). Thus this patch removes it
from cacheflush.h and from ARCH=powerpc (misc_32.S) entirely. It's
left in ARCH=ppc for now, with the prototype moved to ppc_ksyms.c.
Built for Walnut (ARCH=ppc), 32-bit multiplatform (pmac, CHRP and PReP
ARCH=ppc, pmac and CHRP ARCH=powerpc). Built and booted on POWER5
LPAR (ARCH=powerpc and ARCH=ppc64).
Built for 32-bit powermac (ARCH=ppc and ARCH=powerpc). Built and
booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64). Built and booted
on G5 (ARCH=powerpc)
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code to work around some problems with old versions of
Open Firmware, such as on the early powermacs (7500 etc.) and the
"Longtrail" CHRP machine. On these machines we have to claim
the physical and virtual address ranges explicitly when claiming
memory and then set up a V->P mapping.
The Longtrail has more problems: setprop doesn't work, and we have
to set an "allow-reclaim" variable to 0 in order to get claim on
physical memory ranges to fail if the memory is already claimed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes ppc44x fpu support that broke from a bad arch/powerpc merge.
Instead of adding KernelFP back in (which duplicates code) we use
the same kernel fpu unavailable handler as classic PPC processors.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Having already merged the ppc and ppc64 versions of signal.c, this
patch finishes the job by merging signal.h. The two versions were
almost identical already. Notable changes:
- We use BITS_PER_LONG to correctly size sigset_t
- Remove some uneeded #includes and struct forward
declarations. This does mean adding an include to signal_32.c which
relied on the indirect inclusion of sigcontext.h
- As the ppc64 version, the merged signal.h has prototypes for
do_signal() and do_signal32(). Thus remove extra prototypes from
ppc_ksyms.c which had them directly.
Built and booted on POWER5 LPAR (ARCH=ppc64 and ARCH=powerpc). Built
for 32-bit powermac (ARCH=ppc and ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- Re-add a hunk lost during merge: ppc64 is missing the hunk that disables
preempt on the secondary CPUs before they call cpu_idle().
- ppc's cpu_idle() had the need_resched() test wrong.
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid. Improves efficiency of
resched_task and some cpu_idle routines.
* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
and as we hold it during resched_task, then there is no need for an
atomic test and set there. The only other time this should be set is
when the task's quantum expires, in the timer interrupt - this is
protected against because the rq lock is irq-safe.
- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
won't get unset until the task get's schedule()d off.
- If we are running on the same CPU as the task we resched, then set
TIF_NEED_RESCHED and no further action is required.
- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
after TIF_NEED_RESCHED has been set, then we need to send an IPI.
Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.
* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
becomes true, explicitly call schedule(). This makes things a bit clearer
(IMO), but haven't updated all architectures yet.
- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
to the resched_task rules, this isn't needed (and actually breaks the
assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
held). So remove that. Generally one less locked memory op when switching
to the idle thread.
- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
most polling idle loops. The above resched_task semantics allow it to be
set until before the last time need_resched() is checked before going into
a halt requiring interrupt wakeup.
Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
can be always left set, completely eliminating resched IPIs when rescheduling
the idle task.
POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run idle threads with preempt disabled.
Also corrected a bugs in arm26's cpu_idle (make it actually call schedule()).
How did it ever work before?
Might fix the CPU hotplugging hang which Nigel Cunningham noted.
We think the bug hits if the idle thread is preempted after checking
need_resched() and before going to sleep, then the CPU offlined.
After calling stop_machine_run, the CPU eventually returns from preemption and
into the idle thread and goes to sleep. The CPU will continue executing
previous idle and have no chance to call play_dead.
By disabling preemption until we are ready to explicitly schedule, this bug is
fixed and the idle threads generally become more robust.
From: alexs <ashepard@u.washington.edu>
PPC build fix
From: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
MIPS build fix
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MPC834x uses the gianfar network driver which now uses the new phylib. We
need to update the platform code to create a gianfar platform MDIO bus and
pass the right intializations to the gianfar driver to make things work
again.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes mismerged Makefile that prevented the ppc85xx rapidio support from being
built.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
xmon() prototype is inconsistent between ARCH=ppc and ARCH=powerpc,
thus causing ARCH=ppc build breakage.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the ability to the SMU driver to recover missing
calibration partitions from the SMU chip itself. It also adds some
dynamic mecanism to /proc/device-tree so that new properties are visible
to userland.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the arch/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in arch/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
human-time conversion functions instead of hard-coded HZ division to avoid
rounding errors.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updates the RIO messaging interface to pass a device instance into the
event registeration and callbacks.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds PPC32 RIO support. Init code for the MPC85xx RIO ports and glue for the
STx GP3 board to use it.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kconfig patch needed by fs_enet to work. Works like CONFIG_CPM2.
Cc: Kumar <kumar.gala@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This missing initrd header slipped though last time.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On PPC405GP/GPR it should be possible to enable PCI support, even when the
internal PCI arbiter is disabled (e.g. when using an external PCI
arbiter). The removed code didn't allow this, and also generated a warning
on PPC405EP platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup PPC40x eval boards (bubinga, walnut and sycamore) to support U-Boot
as bootloader. The OpenBIOS bd_info struct is not used in the kernel
anymore (only U-Boot now).
uImage (U-Boot) tested on walnut, sycamore and bubinga
zImage (OpenBIOS) tested on sycamore, bubinga and ebony
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the AMCC PowerPC 440SPe SoC, including PCI Express in root
port mode.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerPC 440SP SoC has two Processor Local Bus (PLB) segments (a
high-throughput segment and a low-latency segment). Fix our PLB register
definitions to cope with this, and add code to dump the status of both
segments when a machine check occurs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerPC 440SPe supports up to 16 GB of RAM, and therefore its IO registers
are at 0x4_xxxx_xxxx instead of being at 0x1_xxxx_xxxx like most other PPC 440
chips. To allow for this, this patch moves the definition of the ERPN used
for mapping UART0 from being hard-coded in the head_44x.S assembly code to
being defined in ibm44x.h.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds watchdog, RTC support for Marvell EV64360BP board.
Signed-off-by: Lee Nicks <allinux@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds exception table entries for I/O instructions on and
changes MachineCheckException() slightly to cover 8xx specifics (on
8xx the MCE can be generated while executing the IO access instruction
itself, which is not the case on PowerMac's, as the comment on traps.c
details).
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch against m8xx_wdt.c adds <asm/io.h> (required for
out,in_be32/16) and fixes syntatic problems introduced with the IO
accessor macro update.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also moves setup_cpu_maps to setup-common.c (calling it
smp_setup_cpu_maps) and uses it on both 32-bit and 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds missing header and thus fix the warning issued by ming prototype.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current comment on top of m8xx_cpm_dpinit is wrong.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The latest updates to bug.h generate build warnings in traps.c in
arch/ppc. Fix print format specifiers to account for change of line type
to long from int.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge include/asm-ppc/kexec.h and include/asm-ppc64/kexec.h.
The only thing that's really changed is that we now allocate crash_notes
properly on PPC32. It's address is exported via sysfs, so it's not correct
for it to be a pointer.
I've also removed some of the "we don't use this" comments, because they're
wrong (or perhaps were referring only to arch code).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Here's a revised version. This re-introduces the set_bits() function
from ppc64, which I removed because I thought it was unused (it exists
on no other arch). In fact it is used in the powermac interrupt code
(but not on pSeries).
- We use LARXL/STCXL macros to generate the right (32 or 64 bit)
instructions, similar to LDL/STL from ppc_asm.h, used in fpu.S
- ppc32 previously used a full "sync" barrier at the end of
test_and_*_bit(), whereas ppc64 used an "isync". The merged version
uses "isync", since I believe that's sufficient.
- The ppc64 versions of then minix_*() bitmap functions have changed
semantics. Previously on ppc64, these functions were big-endian
(that is bit 0 was the LSB in the first 64-bit, big-endian word).
On ppc32 (and x86, for that matter, they were little-endian. As far
as I can tell, the big-endian usage was simply wrong - I guess
no-one ever tried to use minixfs on ppc64.
- On ppc32 find_next_bit() and find_next_zero_bit() are no longer
inline (they were already out-of-line on ppc64).
- For ppc64, sched_find_first_bit() has moved from mmu_context.h to
the merged bitops. What it was doing in mmu_context.h in the first
place, I have no idea.
- The fls() function is now implemented using the cntlzw instruction
on ppc64, instead of generic_fls(), as it already was on ppc32.
- For ARCH=ppc, this patch requires adding arch/powerpc/lib to the
arch/ppc/Makefile. This in turn requires some changes to
arch/powerpc/lib/Makefile which didn't correctly handle ARCH=ppc.
Built and running on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define jiffies_64 in kernel/timer.c rather than having 24 duplicated
defines in each architecture.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure we always return, as all syscalls should. Also move the common
prototype to <linux/syscalls.h>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed some more references to check_region().
I checked these changes into the 'checkreg' branch of
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6.git
The only valid references remaining are in:
drivers/scsi/advansys.c
drivers/scsi/BusLogic.c
drivers/cdrom/sbpcd.c
sound/oss/pss.c
Remove last vestiges of ide_check_region()
drivers/char/specialix: trim trailing whitespace
drivers/char/specialix: eliminate use of check_region()
Remove outdated and unused references to check_region()
[sound oss] remove check_region() usage from cs4232, wavfront
[netdrvr eepro] trim trailing whitespace
[netdrvr eepro] remove check_region() usage
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
First step in pushing down the page_table_lock. init_mm.page_table_lock has
been used throughout the architectures (usually for ioremap): not to serialize
kernel address space allocation (that's usually vmlist_lock), but because
pud_alloc,pmd_alloc,pte_alloc_kernel expect caller holds it.
Reverse that: don't lock or unlock init_mm.page_table_lock in any of the
architectures; instead rely on pud_alloc,pmd_alloc,pte_alloc_kernel to take
and drop it when allocating a new one, to check lest a racing task already
did. Similarly no page_table_lock in vmalloc's map_vm_area.
Some temporary ugliness in __pud_alloc and __pmd_alloc: since they also handle
user mms, which are converted only by a later patch, for now they have to lock
differently according to whether or not it's init_mm.
If sources get muddled, there's a danger that an arch source taking
init_mm.page_table_lock will be mixed with common source also taking it (or
neither take it). So break the rules and make another change, which should
break the build for such a mismatch: remove the redundant mm arg from
pte_alloc_kernel (ppc64 scrapped its distinct ioremap_mm in 2.6.13).
Exceptions: arm26 used pte_alloc_kernel on user mm, now pte_alloc_map; ia64
used pte_alloc_map on init_mm, now pte_alloc_kernel; parisc had bad args to
pmd_alloc and pte_alloc_kernel in unused USE_HPPA_IOREMAP code; ppc64
map_io_page forgot to unlock on failure; ppc mmu_mapin_ram and ppc64 im_free
took page_table_lock for no good reason.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a numbers of issues regarding to that both 8xx and 82xx
began to use ppc_sys model:
- Platform is now identified by default deviceless SOC, if no
BOARD_CHIP_NAME is specified in the bard-specific header. For the list
of supported names refer to (arch/ppc/syslib/) mpc8xx_sys.c and
mpc82xx_sys.c for 8xx and 82xx respectively.
- Fixed a bug in identification by name - if the name was not found,
it returned -1 instead of default deviceless ppc_spec.
- fixed devices amount in the 8xx platform system descriptions
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates the 85xx platform code to support the new PHY Layer.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <Kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add proper entry to support the Marvell MV64361 (Marvell Discovery II)
SRAM.
This feature may be used by the mv643xx_eth driver.
Signed-off-by: Nicolas DET <det.nicolas@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements a nvram acccess method, similar to
arch/ppc64/kernel/pSeries_nvram.c tested on CHRP B50.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the phys_mem_access_prot() function to take a pfn instead of an
address. This allows mmap64() to work on /dev/mem for addresses above 4G
on 32-bit architectures. We start with a pfn in mmap_mem(), so there's no
need to convert to an address; in fact, it's actively bad, since the
conversion can overflow when the address is above 4G.
Similarly fix the ppc32 page_is_ram() function to avoid a conversion to an
address by directly comparing to max_pfn. Working with max_pfn instead of
high_memory fixes page_is_ram() to give the right answer for highmem pages.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mention a few more commands in xmon. System.map processing was replaced
with kallsyms.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
#ifdef out an ALTIVEC specific tweak in __switch_to()
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup PPC440 eval boards (bamboo, ebony, luan and ocotea) to better
support U-Boot as bootloader.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert core 8xx drivers to use in_xxxbe/in_xxx macros instead of direct
memory references.
Other than making IO accesses explicit (which is a plus for readability), a
common set of macros provides a unified place for the volatile flag to
constraint compiler code reordering.
There are several unlucky places at the moment which lack the volatile
flag.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Depending on how GCC is built, GCC 4 may generate altivec instructions without
user explicitly requesting vector operations in the code. Although this is a
performance booster for user applications, it is a problem for kernel.
This patch explicitly instruct GCC to NOT generate altivec instructions while
building the kernel.
Here are some test cases I ran.
(1) build gcc 4.0.1 with '--with-cpu=7450 --enable-altivec
--enable-cxx-flags=-mcpu=7450', and use this gcc to build kernel WITHOUT
this kernel patch. Kernel fail to boot up on a 7450 board because of
altivec instructions in kernel.
(2) build gcc 4.0.1 with "--with-cpu=7450 --enable-altivec
--enable-cxx-flags=-mcpu=7450", and use this gcc to build kernel WITH this
kernel patch. Kernel boot up on a 7450 board without any problem.
(3) build gcc 4.0.1 with "--with-cpu=750 --enable-cxx-flags=-mcpu=750",
and use this gcc to build kernel with or without this kernel patch.
Kernel boot up on a 7450 board without any problem.
This patch should also work with GCC 3 or even earlier GCC 2.95.3.
Signed-off-by: Lee Nicks <allinux@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent merge of fpu.S broken the handling of fpscr for
ARCH=powerpc and CONFIG_PPC64=y. FP registers could be corrupted,
leading to strange random application crashes.
The confusion arises, because the thread_struct has (and requires) a
64-bit area to save the fpscr, because we use load/store double
instructions to get it in to/out of the FPU. However, only the low
32-bits are actually used, so we want to treat it as a 32-bit quantity
when manipulating its bits to avoid extra load/stores on 32-bit. This
patch replaces the current definition with a structure of two 32-bit
quantities (pad and val), to clarify things as much as is possible.
The 'val' field is used when manipulating bits, the structure itself
is used when obtaining the address for loading/unloading the value
from the FPU.
While we're at it, consolidate the 4 (!) almost identical versions of
cvt_fd() and cvt_df() (arch/ppc/kernel/misc.S,
arch/ppc64/kernel/misc.S, arch/powerpc/kernel/misc_32.S,
arch/powerpc/kernel/misc_64.S) into a single version in fpu.S. The
new version takes a pointer to thread_struct and applies the correct
offset itself, rather than a pointer to the fpscr field itself, again
to avoid confusion as to which is the correct field to use.
Finally, this patch makes ARCH=ppc64 also use the consolidated fpu.S
code, which it previously did not.
Built for G5 (ARCH=ppc64 and ARCH=powerpc), 32-bit powermac (ARCH=ppc
and ARCH=powerpc) and Walnut (ARCH=ppc, CONFIG_MATH_EMULATION=y).
Booted on G5 (ARCH=powerpc) and things which previously fell over no
longer do.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Talk about buggy firmware... the OF on the Longtrail returns 0
from the claim client service rather than -1 when the claim fails.
It also has no device_type on the /memory node and blows up if
the output buffer for package-to-path is too big.
This also fixes a bug with calling alloc_up with align == 0, where
we did _ALIGN_UP(alloc_bottom, 0) which will end up as 0.
Lastly, we now check the return value (in r3) from calling the
prom, and return -1 from call_prom if we get a negative value back.
That is supposed to indicate that the requested client service
doesn't exist.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the parameters for i8259_init so that it takes two
parameters: a physical address for generating an interrupt
acknowledge cycle, and an interrupt number offset. i8259_init
now sets the irq_desc[] for its interrupts; all the callers
were doing this, and that code is gone now. This also defines
a CONFIG_PPC_I8259 symbol to select i8259.o for inclusion, and
makes the platforms that need it select that symbol.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This defines a CONFIG_INDIRECT_PCI symbol to control whether it
gets used or not, and fixes the Kconfig to select that symbol for
platforms that need it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A recent patch updated the name of pci_assign_all_busses to
pci_assign_all_buses. This instance of its use wasn't corrected
by the original patch to use the new name.
Builds cleanly on ads8272.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously it claimed 7MB starting at the 9M point and loaded the
kernel there. That meant that prom_init put the flattened device
tree above 16M. On the 601 that caused the early device tree scan
to fail, since only 16MB are mapped with BATs on the 601. Moving
this down to 8MB allows prom_init to put the flattened device tree
between 15M and 16M, so it works on the 601.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge ppc32 and ppc64 versions of thread_info.h. They were pretty
similar already, the chief changes are:
- Instead of inline asm to implement current_thread_info(),
which needs to be different for ppc32 and ppc64, we use C with an
asm("r1") register variable. gcc turns it into the same asm as we
used to have for both platforms.
- We replace ppc32's 'local_flags' with the ppc64
'syscall_noerror' field. The noerror flag was in fact the only thing
in the local_flags field anyway, so the ppc64 approach is simpler, and
means we only need a load-immediate/store instead of load/mask/store
when clearing the flag.
- In readiness for 64k pages, when THREAD_SIZE will be less
than a page, ppc64 used kmalloc() rather than get_free_pages() to
allocate the kernel stack. With this patch we do the same for ppc32,
since there's no strong reason not to.
- For ppc64, we no longer export THREAD_SHIFT and THREAD_SIZE
via asm-offsets, thread_info.h can now be safely included in asm, as
on ppc32.
Built and booted on G4 Powerbook (ARCH=ppc and ARCH=powerpc) and
Power5 (ARCH=ppc64 and ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This declares powersave_nap in system.h and makes it an int everywhere,
fixes typos for the maple platform, fixes a couple of places where
I missed removing the last two arguments from a message_pass function,
and makes ppc64 consistent with ppc32 in the type of the
pci_bridge.cfg_data field.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patches the ppc32 and ppc64 versions of the headers and .c files
with helper functions for manipulating the performance counting
hardware. As a side effect, it removes use of the term "perfmon" from
ppc32, thus avoiding confusion with the unrelated performance counter
interface from HP Labs also called "perfmon".
Built, but not booted, for g5, pSeries, iSeries, and 32-bit Powermac
with both ARCH=powerpc and ARCH=ppc{,64} as appropriate.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The _GLOBAL() macro is for text symbols only. Changed to using
.globl for .data symbols. This is also needed in ppc32 land
to allow FSL Book-E, 40x, and 44x to work.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We now use the merged time.c for both 32-bit and 64-bit compilation
with ARCH=powerpc, and for ARCH=ppc64, but not for ARCH=ppc32.
This removes setup_default_decr (folds its function into time_init)
and moves wakeup_decrementer into time.c. This also makes an
asm-powerpc/rtc.h.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes platform code use the smp_ops variable directly instead
of ppc_md.smp_ops, removes the two unused `data' and `wait' arguments
from the *_message_pass() functions, and removes the call to the
never-implemented smp_ops->space_timers() function.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes ppc use the syscalls.c from arch/powerpc/kernel, exports
copy_and_flush from head_32.S for use by prom_init.c (ARCH=powerpc),
and consolidates the sys_fadvise64_64 implementations for 32-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Glibc is about to get some new high precision timer stuff that relies on
the standard timebase of the PPC architecture.
However, some (rare & old) CPUs do not have such timebase and it is a
bit annoying to have your stuff just crash because you are running on
the wrong CPU...
This exposes to userland a CPU feature bit that tells that the current
processor doesn't have a standard timebase. It's negative logic so that
glibc will still "just work" on older kernels (it will just be unhappy
on those old CPUs but that doesn't really matter as distro tend to
update glibc & kernel at the same time).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've noticed that the calculations for seg_size and nr_segs in
__dma_sync_page_highmem() (arch/ppc/kernel/dma-mapping.c) are wrong. The
incorrect calculations can result in either an oops or a panic when running
fsck depending on the size of the partition.
The problem with the seg_size calculation is that it can result in a
negative number if size is offset > size. The problem with the nr_segs
caculation is returns the wrong number of segments, e.g. it returns 1 when
size is 200 and offset is 4095, when it should return 2 or more.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes up a variety of minor problems in compiling with ARCH=ppc
arising from using the merged versions of various header files.
A lot of the changes are just adding #include <asm/machdep.h> to
files that use ppc_md or smp_ops_t.
This also arranges for us to use semaphore.c, vecemu.c, vector.S and
fpu.S from arch/powerpc/kernel when compiling with ARCH=ppc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now instead of having a ppc_md function, we just have a variable
which says whether to do the i8259 irq canonicalization or not,
and set that variable on the platforms that need that. It looks
to me that radstone_ppc7d was trying to use irq canonicalization
for something else in a broken kind of way - it will need to be
fixed properly.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also puts a copy of indirect_pci.c in arch/powerpc/sysdev
so that we don't need to build in arch/ppc/syslib.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Older Macs which uses the VIA chip timers to calibrate the timebase used
some code that wouldn't work if HZ wasn't divisible by 100...
This fixes it at least for 250. Not totally perfect but should be
enough for now (so it at least works with the default value which is now
250).
There is still a potential issue with the core using CLOCK_TICK_RATE to
maintain xtime and CLOCK_TICK_RATE value on ppc32 is pure crap, but that
is a different problem, this patch at least brings us back to our
previous situation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the new iBook G4 (manufactured after July 2005) to the
PowerMac models table. The model name (PowerBook6,7) is taken from a
12" iBook, I don't know if it also matches the 14" version. The patch
applies to a vanilla 2.6.13.2 kernel.
Signed-off-by: Sven Henkel <shenkel@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use idle_power4.S from ppc64 as we are not going to support
32 bit power4 in the merged tree.
Merge ppc64 traps.c into powerpc traps.c:
use ppc64 versions of exception routine names
(as they don't have StudlyCaps)
make all the versions if die() have the same
prototype
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
The old 550Mhz titanium powerbook can switch to a lower frequency
(500Mhz). A user has been repeately reporting overtemp conditions on his
machine at high speed so this simple patch adds support to PowerMac
cpufreq for this machine. The difference in frequency isn't big but seem
enough to fix that user's problems. The patch has been around for some
time now and doesn't seem to cause any problem, so I suppose it could go
in now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alain RICHARD <alain.richard@equation.fr>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In arch/ppc/boot/ld.script we need OUTPUT_ARCH(powerpc:common) for the
same reasons why we need it in vmlinux.lds.S; when we build on ppc64
box, we need to be explicit about the target.
See http://linus.bkbits.net:8080/linux-2.5/cset@1.1784.8.10 for the
corresponding fix in vmlinux.lds.S.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I did something stupid in my oprofile fix, here's the obvious fix:
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This merges ppc_ksyms.c, puts back the actual do_execve call in
sys_execve, makes init_MMU call find_end_of_memory rather than
ppc_md.find_end_of_memory (every platform has a device tree
with a /memory node now, right?) and fixes some problems with the
mpic initialization on newworld powermacs.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Changed ppc32 so that cur_cpu_spec is just a single pointer for all CPUs.
Additionally, made call_setup_cpu check to see if the cpu_setup pointer
is NULL or not before calling the function. This lets remove the dummy
cpu_setup calls that just return.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merged cputable.h between ppc32 and ppc64. In doing this removed support
for the BEGIN_FTR_SECTION/END_FTR_SECTION macros in C code since they
dont compile correctly. C code should use cpu_has_feature(). This is
based on Arnd Bergmann's initial patch.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SMU is the "system controller" chip used by Apple recent G5 machines
including the iMac G5. It drives things like fans, i2c busses, real time
clock, etc...
The current kernel contains a very crude driver that doesn't do much more
than reading the real time clock synchronously. This is a completely
rewritten driver that provides interrupt based command queuing, a userland
interface, and an i2c/smbus driver for accessing the devices hanging off
the SMU i2c busses like temperature sensors. This driver is a basic block
for upcoming work on thermal control for those machines, among others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current -git tree doesn't build when enabling oprofile on a non-bookE CPU
(like on a PowerMac for example). While there is no performance counter
support for these CPUs implemented yet, it's still nice to be able to use
the timer based sampling, and that got broken.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For platforms that don't have PCI IO at 0 the outbound window
registers were not being properly configured.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This merges the asm-ppc*/dma.h files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc32/ppc64: Merge bug.h into include/asm-powerpc
This patch merges bug.h into include/asm-powerpc. Changed the data
structure for bug_entry such that line is always an int on both 32 and
64-bit platforms; removed casts to int from the 64-bit trap code to
reflect this.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Becky Bruce <Becky.Bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a revised patch to merge asm-ppc*/hardirq.h.
It removes some unnecessary #includes, but then requires
the addition of #include <asm/irq.h> in PPC32's hw_irq.h
much like ppc64 already does. Furthermore, several
unnecessary #includes were removed from some ppc32 boards
in order to break resulting bad #include cycles.
Builds pSeries_defconfig and all ppc32 platforms except
the already b0rken bseip.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename and slightly modify {request,free}_perfmon_irq in the ppc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- merge common.c
- move model specific files
- remove stub Makefiles
- clean up arch/ppc*/Makefile
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge include/asm-ppc64/oprofile_ipml.h and arch/ppc/oprofile/op_impl.h
into include/asm-powerpc/oprofile_ipml.h
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This file is the same in both architectures so create arch/powerpc/kernel
and move it there.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Made the CHRP/PMAC/PREP config options selectable by the user.
This allows us to build kernels specifically for one of the
platforms thus reducing code size.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Made the CHRP/PMAC/PREP config options selectable by the user.
This allows us to build kernels specifically for one of the
platforms thus reducing code size.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here is a new patch that removes all notion of the pmac, prep,
chrp and openfirmware initialization sections, and then unifies
the sections.h files without those __pmac, etc, sections identifiers
cluttering things up.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here is a new patch that removes all notion of the pmac, prep,
chrp and openfirmware initialization sections, and then unifies
the sections.h files without those __pmac, etc, sections identifiers
cluttering things up.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We always use the inlined versions of local_irq_enable, local_irq_disable,
local_save_flags_ptr, and local_irq_restore on ppc32 so the non-inlined
versions where just taking up space.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merged ppc_asm.h between ppc32 & ppc64. The majority of the file is
common between the two architectures excluding how a single GPR is
saved/restored and which GPRs are non-volatile.
Additionally, moved the ASM_CONST macro used on ppc64 into ppc_asm.h.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added ppc_sys device and system definitions for PowerQUICC I devices. This
will allow drivers for PQI to be proper platform device drivers. Currently
sys section contains only MPC885 and MPC866. Identification should be done
with identify_ppc_sys_by_name call, with board-specific "name" string
passed, since PQI do not have any register that could identify the SOC.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up some pm_message_t types
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Several implementations were essentialy a common piece of C code using
the cmpxchg() macro. Put the implementation in one spot that everyone
can share, and convert sparc64 over to using this.
Alpha is the lone arch-specific implementation, which codes up a
special fast path for the common case in order to avoid GP reloading
which a pure C version would require.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed ppc32 architecture specific users of asm/segment.h and
asm-ppc/segment.h itself
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Discard *.exit.text sections on runtime. We cannot do this on link time
because of the way BUG macros are implemented. If "__exit function" calls
one of those macros, __bug_table section will reference this function.
This is similar to ".altinstructions" situation on i386.
*.exit.data seems to be OK in this respect and is discarded on link
time.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When introducing the generic asm-offsets.h support the dependency
chain for the prepare targets was changed. All build scripts expecting
include/asm/asm-offsets.h to be made when using the prepare target would broke.
With the limited number of prepare targets left in arch Makefiles
the trivial solution was to introduce a new arch specific target: archprepare
The dependency chain looks like this now:
prepare
|
+--> prepare0
|
+--> archprepare
|
+--> scripts_basic
+--> prepare1
|
+---> prepare2
|
+--> prepare3
So prepare 3 is processed before prepare2 etc.
This guaantees that the asm symlink, version.h, scripts_basic
are all updated before archprepare is processed.
prepare0 which build the asm-offsets.h file will need the
actions performed by archprepare.
The head target is now named prepare, because users scripts will most
likely use that target, but prepare-all has been kept for compatibility.
Updated Documentation/kbuild/makefiles.txt.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This is less troublesome and makes more sense.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows cpus to be off-lined on 32-bit SMP powermacs. When a cpu
is off-lined, it is put into sleep mode with interrupts disabled. It
can be on-lined again by asserting its soft-reset pin, which is
connected to a GPIO pin.
With this I can off-line the second cpu in my dual G4 powermac, which
means that I can then suspend the machine (the suspend/resume code
refuses to suspend if more than one cpu is online, and making it cope
with multiple cpus is surprisingly messy).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch that I have had in my tree for ages. If init causes
an exception that raises a signal, such as a SIGSEGV, SIGILL or
SIGFPE, and it hasn't registered a handler for it, we don't deliver
the signal, since init doesn't get any signals that it doesn't have a
handler for. But that means that we just return to userland and
generate the same exception again immediately. With this patch we
print a message and kill init in this situation.
This is very useful when you have a bug in the kernel that means that
init doesn't get as far as executing its first instruction. :)
Without this patch the system hangs when it gets to starting the
userland init; with it you at least get a message giving you a clue
about what has gone wrong.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the most trivial from Rusty's trivial patches:
- spelling fixes
- remove duplicate includes
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert the initializers of hw_interrupt_type structures to C99 initializers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch (written by me and also containing many suggestions of Arjan van
de Ven) does a major cleanup of the spinlock code. It does the following
things:
- consolidates and enhances the spinlock/rwlock debugging code
- simplifies the asm/spinlock.h files
- encapsulates the raw spinlock type and moves generic spinlock
features (such as ->break_lock) into the generic code.
- cleans up the spinlock code hierarchy to get rid of the spaghetti.
Most notably there's now only a single variant of the debugging code,
located in lib/spinlock_debug.c. (previously we had one SMP debugging
variant per architecture, plus a separate generic one for UP builds)
Also, i've enhanced the rwlock debugging facility, it will now track
write-owners. There is new spinlock-owner/CPU-tracking on SMP builds too.
All locks have lockup detection now, which will work for both soft and hard
spin/rwlock lockups.
The arch-level include files now only contain the minimally necessary
subset of the spinlock code - all the rest that can be generalized now
lives in the generic headers:
include/asm-i386/spinlock_types.h | 16
include/asm-x86_64/spinlock_types.h | 16
I have also split up the various spinlock variants into separate files,
making it easier to see which does what. The new layout is:
SMP | UP
----------------------------|-----------------------------------
asm/spinlock_types_smp.h | linux/spinlock_types_up.h
linux/spinlock_types.h | linux/spinlock_types.h
asm/spinlock_smp.h | linux/spinlock_up.h
linux/spinlock_api_smp.h | linux/spinlock_api_up.h
linux/spinlock.h | linux/spinlock.h
/*
* here's the role of the various spinlock/rwlock related include files:
*
* on SMP builds:
*
* asm/spinlock_types.h: contains the raw_spinlock_t/raw_rwlock_t and the
* initializers
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* asm/spinlock.h: contains the __raw_spin_*()/etc. lowlevel
* implementations, mostly inline assembly code
*
* (also included on UP-debug builds:)
*
* linux/spinlock_api_smp.h:
* contains the prototypes for the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*
* on UP builds:
*
* linux/spinlock_type_up.h:
* contains the generic, simplified UP spinlock type.
* (which is an empty structure on non-debug builds)
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* linux/spinlock_up.h:
* contains the __raw_spin_*()/etc. version of UP
* builds. (which are NOPs on non-debug, non-preempt
* builds)
*
* (included on UP-non-debug builds:)
*
* linux/spinlock_api_up.h:
* builds the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*/
All SMP and UP architectures are converted by this patch.
arm, i386, ia64, ppc, ppc64, s390/s390x, x64 was build-tested via
crosscompilers. m32r, mips, sh, sparc, have not been tested yet, but should
be mostly fine.
From: Grant Grundler <grundler@parisc-linux.org>
Booted and lightly tested on a500-44 (64-bit, SMP kernel, dual CPU).
Builds 32-bit SMP kernel (not booted or tested). I did not try to build
non-SMP kernels. That should be trivial to fix up later if necessary.
I converted bit ops atomic_hash lock to raw_spinlock_t. Doing so avoids
some ugly nesting of linux/*.h and asm/*.h files. Those particular locks
are well tested and contained entirely inside arch specific code. I do NOT
expect any new issues to arise with them.
If someone does ever need to use debug/metrics with them, then they will
need to unravel this hairball between spinlocks, atomic ops, and bit ops
that exist only because parisc has exactly one atomic instruction: LDCW
(load and clear word).
From: "Luck, Tony" <tony.luck@intel.com>
ia64 fix
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjanv@infradead.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Mikael Pettersson <mikpe@csd.uu.se>
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the final 20 DEFINE_SPINLOCK holdouts. (another 580 places
are already using DEFINE_SPINLOCK). Build tested on x86.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up timer initialization by introducing DEFINE_TIMER a'la
DEFINE_SPINLOCK. Build and boot-tested on x86. A similar patch has been
been in the -RT tree for some time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch changes the usages of PVR_440* into strcmp's with the
cpu_name field, and removes the defines altogether. The Ebony portion was
briefly tested long ago. One benefit of moving from PVR-tests to string
tests in general is that not all CPUs can be on and be able to do this type
of comparison.
See http://patchwork.ozlabs.org/linuxppc/patch?id=1250 for the original
thread.
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modifies serial_init to get base baud rate from the rs_table entry instead
of BAUD_BASE. This patch eliminates duplication between the
SERIAL_PORT_DFNS macro and BAUD_BASE. Without the patch, if a port set the
baud rate in SERIAL_PORT_DFNS, but did not update BASE_BAUD, the BASE_BAUD
value would still be used.
Signed-off-by: Grant Likely <grant.likely@gdcanada.com>
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the flush and invalidate bootcode on PPC4xx we were accidentally using
the wrong instruction. Use cmplw, which reads from a register like we
want.
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Subject says it all, there is no need to link perfmon.o on
sub-architectures other than CONFIG_E500.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Looks like the help comment for MPC834x got merged incorrectly.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make check_bugs() static inline and remove it from syscalls.c.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rather than hard-coding the platform device IDs, enumerate them.
We don't particularly care about the actual ID we get, just as
long as they're unique.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
head_4xx.S wasn't compiling due to a missing #endif
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitized and fixed floppy dependencies: split the messy dependencies for
BLK_DEV_FD by introducing a new symbol (ARCH_MAY_HAVE_PC_FDC), making
BLK_DEV_FD depend on that one and taking declarations of ARCH_MAY_HAVE_PC_FDC
to arch/*/Kconfig. While we are at it, fixed several obvious cases when
BLK_DEV_FD should have been excluded (architectures lacking asm/floppy.h
are *not* going to have floppy.c compile, let alone work).
If you can come up with better name for that ("this architecture might
have working PC-compatible floppy disk controller"), you are more than
welcome - just s/ARCH_MAY_HAVE_PC_FDC/your_prefered_name/g in the patch
below...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch cleans up a commonly repeated set of changes to the NTP state
variables by adding two helper inline functions:
ntp_clear(): Clears the ntp state variables
ntp_synced(): Returns 1 if the system is synced with a time server.
This was compile tested for alpha, arm, i386, x86-64, ppc64, s390, sparc,
sparc64.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
