Add a parameter to avoid using MSI/MSI-X for PCIe native hotplug; it's
known to be buggy on some platforms.
In my environment, while shutting down, following stack trace is shown
sometimes.
irq 16: nobody cared (try booting with the "irqpoll" option)
Pid: 1081, comm: reboot Not tainted 3.2.0 #1
Call Trace:
<IRQ> [<ffffffff810cec1d>] __report_bad_irq+0x3d/0xe0
[<ffffffff810cee1c>] note_interrupt+0x15c/0x210
[<ffffffff810cc485>] handle_irq_event_percpu+0xb5/0x210
[<ffffffff810cc621>] handle_irq_event+0x41/0x70
[<ffffffff810cf675>] handle_fasteoi_irq+0x55/0xc0
[<ffffffff81015356>] handle_irq+0x46/0xb0
[<ffffffff814fbe9d>] do_IRQ+0x5d/0xe0
[<ffffffff814f146e>] common_interrupt+0x6e/0x6e
[<ffffffff8106b040>] ? __do_softirq+0x60/0x210
[<ffffffff8108aeb1>] ? hrtimer_interrupt+0x151/0x240
[<ffffffff814fb5ec>] call_softirq+0x1c/0x30
[<ffffffff810152d5>] do_softirq+0x65/0xa0
[<ffffffff8106ae9d>] irq_exit+0xbd/0xe0
[<ffffffff814fbf8e>] smp_apic_timer_interrupt+0x6e/0x99
[<ffffffff814f9e5e>] apic_timer_interrupt+0x6e/0x80
<EOI> [<ffffffff814f0fb1>] ? _raw_spin_unlock_irqrestore+0x11/0x20
[<ffffffff812629fc>] pci_bus_write_config_word+0x6c/0x80
[<ffffffff81266fc2>] pci_intx+0x52/0xa0
[<ffffffff8127de3d>] pci_intx_for_msi+0x1d/0x30
[<ffffffff8127e4fb>] pci_msi_shutdown+0x7b/0x110
[<ffffffff81269d34>] pci_device_shutdown+0x34/0x50
[<ffffffff81326c4f>] device_shutdown+0x2f/0x140
[<ffffffff8107b981>] kernel_restart_prepare+0x31/0x40
[<ffffffff8107b9e6>] kernel_restart+0x16/0x60
[<ffffffff8107bbfd>] sys_reboot+0x1ad/0x220
[<ffffffff814f4b90>] ? do_page_fault+0x1e0/0x460
[<ffffffff811942d0>] ? __sync_filesystem+0x90/0x90
[<ffffffff8105c9aa>] ? __cond_resched+0x2a/0x40
[<ffffffff814ef090>] ? _cond_resched+0x30/0x40
[<ffffffff81169e17>] ? iterate_supers+0xb7/0xd0
[<ffffffff814f9382>] system_call_fastpath+0x16/0x1b
handlers:
[<ffffffff8138a0f0>] usb_hcd_irq
[<ffffffff8138a0f0>] usb_hcd_irq
[<ffffffff8138a0f0>] usb_hcd_irq
Disabling IRQ #16
An un-wanted interrupt is generated when PCI driver switches from
MSI/MSI-X to INTx while shutting down the device. The interrupt does
not happen if MSI/MSI-X is not used on the device.
I confirmed that this problem does not happen if pcie_hp=nomsi was
specified and hotplug operation worked fine as usual.
v2: Automatically disable MSI/MSI-X against following device:
PCI bridge: Integrated Device Technology, Inc. Device 807f (rev 02)
v3: Based on the review comment, combile the if statements.
v4: Removed module parameter.
Move some code to build pciehp as a module.
Move device specific code to driver/pci/quirks.c.
v5: Drop a device specific code until getting a vendor statement.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the evaluation of acpi_pci_osc_control_set() (to request control of
PCI Express native features) into acpi_pci_root_add() to avoid calling
it many times for the same root complex with the same arguments.
Additionally, check if all of the requisite _OSC support bits are set
before calling acpi_pci_osc_control_set() for a given root complex.
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-by: Ozan Caglayan <ozan@pardus.org.tr>
Tested-by: Ozan Caglayan <ozan@pardus.org.tr>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I noticed that PCI Express PMEs don't work on my Toshiba Portege R500
after the system has been woken up from a sleep state by a PME
(through Wake-on-LAN). After some investigation it turned out that
the BIOS didn't clear the Root PME Status bit in the root port that
received the wakeup PME and since the Requester ID was also set in
the port's Root Status register, any subsequent PMEs didn't trigger
interrupts.
This problem can be avoided by clearing the Root PME Status bits in
all PCI Express root ports during early resume. For this purpose,
add an early resume routine to the PCIe port driver and make this
driver be always registered, even if pci_ports_disable is set (in
which case the driver's only function is to provide the early
resume callback).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After commit 852972acff (ACPI: Disable
ASPM if the platform won't provide _OSC control for PCIe) control of
the PCIe Capability Structure is unconditionally requested by
acpi_pci_root_add(), which in principle may cause problems to
happen in two ways. First, the BIOS may refuse to give control of
the PCIe Capability Structure if it is not asked for any of the
_OSC features depending on it at the same time. Second, the BIOS may
assume that control of the _OSC features depending on the PCIe
Capability Structure will be requested in the future and may behave
incorrectly if that doesn't happen. For this reason, control of
the PCIe Capability Structure should always be requested along with
control of any other _OSC features that may depend on it (ie. PCIe
native PME, PCIe native hot-plug, PCIe AER).
Rework the PCIe port driver so that (1) it checks which native PCIe
port services can be enabled, according to the BIOS, and (2) it
requests control of all these services simultaneously. In
particular, this causes pcie_portdrv_probe() to fail if the BIOS
refuses to grant control of the PCIe Capability Structure, which
means that no native PCIe port services can be enabled for the PCIe
Root Complex the given port belongs to. If that happens, ASPM is
disabled to avoid problems with mishandling it by the part of the
PCIe hierarchy for which control of the PCIe Capability Structure
has not been received.
Make it possible to override this behavior using 'pcie_ports=native'
(use the PCIe native services regardless of the BIOS response to the
control request), or 'pcie_ports=compat' (do not use the PCIe native
services at all).
Accordingly, rework the existing PCIe port service drivers so that
they don't request control of the services directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce kernel command line switch pcie_ports= allowing one to
disable all of the native PCIe port services, so that PCIe ports
are treated like PCI-to-PCI bridges.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Apparently, some machines may have problems with PCI run-time power
management if MSIs are used for the native PCIe PME signaling. In
particular, on the MSI Wind U-100 PCIe PME interrupts are not
generated by a PCIe root port after a resume from suspend to RAM, if
the system wake-up was triggered by a PME from the device attached to
this port. [It doesn't help to free the interrupt on suspend and
request it back on resume, even if that is done along with disabling
the MSI and re-enabling it, respectively.] However, if INTx
interrupts are used for this purpose on the same machine, everything
works just fine.
For this reason, add a kernel command line switch allowing one to
request that MSIs be not used for the native PCIe PME signaling,
introduce a DMI table allowing us to blacklist machines that need
this switch to be set by default and put the MSI Wind U-100 into this
table.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We don't need pcie_port_device_probe() because we can get pci
device/port type using pci_is_pcie() and 'pcie_type' fields in struct
pci_dev. Remove pcie_port_device_probe().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Implement pm object for the PCI Express port driver in order to use
the new power management framework and reduce the code size.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If MSI-X interrupt mode is used by the PCI Express port driver, too
many vectors are allocated and it is not ensured that the right
vectors will be used for the right services. Namely, the PCI Express
specification states that both PCI Express native PME and PCI Express
hotplug will always use the same MSI or MSI-X message for signalling
interrupts, which implies that the same vector will be used by both
of them. Also, the VC service does not use interrupts at all.
Moreover, is not clear which of the vectors allocated by
pci_enable_msix() in the current code will be used for PME and
hotplug and which of them will be used for AER if all of these
services are configured.
For these reasons, rework the allocation of interrupts for PCI
Express ports so that if MSI-X are enabled, the right vectors will be
used for the right purposes.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI Express port driver uses 'struct pcie_port_service_id' for
matching port service devices and drivers, but this structure
contains fields that duplicate information from the port device
itself (vendor, device, subvendor, subdevice) and fields that are not
used by any existing port service driver (class, class_mask,
drvier_data). Also, both existing port service drivers (AER and
PCIe HP) don't even use the vendor and device fields for device
matching. Therefore 'struct pcie_port_service_id' can be removed
altogether and the only useful members of it (port_type, service) can
be introduced directly into the port service device and port service
driver structures. That simplifies the code quite a bit and reduces
its size.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI Express port driver extension, as defined by struct
pcie_port_device_ext in portdrv.h, is allocated and initialized, but
never used (it also is never freed). Extend it to hold the PCI Express
port type as well as the port interrupt mode, change its name and use it
to simplify the code in portdrv_core.c .
Additionally, remove the redundant interrupt_mode member of struct
pcie_device defined in include/linux/pcieport_if.h .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The 'use pci_find_ext_capability everywhere' cleanup brought a new bug,
which makes the AER stop working. Fix it by actually using find_ext_cap
instead of just find_cap. Drop the unused config space size define while
we're at it.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
__must_check goes on the declaration, not the definition.
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Have pcie_port_bus_register() notice and return errors.
Mark it __must_check so that its caller(s) must check its return value.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch, is based on kernel 2.6.12, provides a fix for PCIe
port bus driver suspend/resume.
Signed-off-by: T. Long Nguyen <tom.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
