Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
-----BEGIN PGP SIGNATURE-----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=CcjQ
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.14 cycle
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
Depends on: 691c4b95d1 ("iio: ad_sigma_delta: Implement a dedicated reset function")
SPI host drivers can use DMA to transfer data, so the buffer should be properly allocated.
Keeping it on the stack could cause an undefined behavior.
The dedicated reset function solves this issue.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a check to see if pmlmepriv is null before vfree'ing
pmlmepriv->free_bss_buf hence implying pmlmepriv could potenially be
null. However, a previous call to rtw_free_mlme_priv_ie_data
can also dereference pmlmepriv, so move this call so that it is only
called if pmlmepriv non-null.
Detected by CoverityScan, CID#1077739 ("Dereference before null check")
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value of the u8 id needs to be upper bounds checked to ensure
the cam_cache array on the adapter dvobj is not indexed outside
of the allowed range of 0..TOTAL_CAM_ENTRY-1. This can currently
occur if id is >= TOTAL_CAM_ENTRY when calling write_cam_from_cache.
Fix this by adding an upper range check.
Detected by CoverityScan, CID#1428464 ("Use of untrusted scalar value")
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a NULL pointer dereference on RPi 2 with multi_v7_defconfig.
The function page_address() could return NULL with enabled CONFIG_HIGHMEM.
So fix this by using kmap() instead.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 71bad7f086 ("staging: add bcm2708 vchiq driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When cursor is at beginning of an empty or whitespace-only line and
speakup-r typed, kernel locks up. This happens because deadlock of in
input_event function over dev->event_lock, as demonstrated by lockdep
logs. The reason for that is speakup simulates a down arrow - because
cursor is at an empty line - while inside key press notifier handler
which is ultimately triggered from input_event function. The simulated
key press leads to input_event being called again, this time under its
own context. So the spinlock is dev->event_lock is acquired while still
being held.
This patch ensures that key press is not simulated from inside key press
notifier handler. Instead it delegates to cursor_timer. It starts the
timer and passes RA_DOWN_ARROW as argument. When timer handler runs and
sees RA_DOWN_ARROW, it will then call kbd_fakekey2(RA_DOWN_ARROW) which
will correctly simulate the keypress inside timer context.
When not inside key press notifier callback, the behaviour will remain
the same as before this patch.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With gcc-4.1.2:
drivers/staging/pi433/rf69.c: In function ‘rf69_set_dio_mapping’:
drivers/staging/pi433/rf69.c:566: warning: ‘regaddr’ may be used uninitialized in this function
drivers/staging/pi433/rf69.c:565: warning: ‘shift’ may be used uninitialized in this function
drivers/staging/pi433/rf69.c:564: warning: ‘mask’ may be used uninitialized in this function
While this is a false positive, it can easily be fixed by moving the
limit check into the "default" case of the switch statement.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to _rtl_dbg_trace via macro HALMAC_RT_TRACE will trigger a null
pointer deference on a null driver_adapter. Fix this by assigning
driver_adapter earlier to halmac_adapter->driver_adapter before the tracing
call so that a non-null driver_adapter is passed instead.
I should have spotted these with an earlier patch I sent, but I overlooked
these in the rather large CoverityScan logs.
Detected by CoverityScan, CID#1454550, CID#1454554, CID#1454565,
CID#1454591, CID#1454598 ("Explicit null dereferenced")
Fixes: 938a0447f0 ("staging: r8822be: Add code for halmac sub-driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current program_page function did following operation:
1. read page (with ECC OFF)
2. modify the page
3. write the page (with ECC ON)
For some case(buggy flash Chip), while read the page without ECC ON,
we may read the page with bit flip error and modify that bad page without
knowing the bit flip error on that page.
also we re-calculate the hash for bad page and write it.
This could bring potential in-consistency problem with Flash data.
Verify this logic with GIGA DEVICE Part(GD5F2GQ4RCFIG):
we see this in-conststency problem wit Giga Device and fix on
this patch resovle that issue.
Signed-off-by: Arun Nagendran <arunrasppi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-4.6 causes a harmless warning about the init function:
WARNING: vmlinux.o(.text+0xed62c2): Section mismatch in reference from the function init_unisys() to the function .init.text:visorutil_spar_detect()
The function init_unisys() references
the function __init visorutil_spar_detect().
This is often because init_unisys lacks a __init
annotation or the annotation of visorutil_spar_detect is wrong.
It appears that newer versions inline visorutil_spar_detect(),
end up with an empty __init section. This marks the module
entry points as __init and __exit respectively, which avoids
the warning and slightly reduces the runtime code size.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull mount flag updates from Al Viro:
"Another chunk of fmount preparations from dhowells; only trivial
conflicts for that part. It separates MS_... bits (very grotty
mount(2) ABI) from the struct super_block ->s_flags (kernel-internal,
only a small subset of MS_... stuff).
This does *not* convert the filesystems to new constants; only the
infrastructure is done here. The next step in that series is where the
conflicts would be; that's the conversion of filesystems. It's purely
mechanical and it's better done after the merge, so if you could run
something like
list=$(for i in MS_RDONLY MS_NOSUID MS_NODEV MS_NOEXEC MS_SYNCHRONOUS MS_MANDLOCK MS_DIRSYNC MS_NOATIME MS_NODIRATIME MS_SILENT MS_POSIXACL MS_KERNMOUNT MS_I_VERSION MS_LAZYTIME; do git grep -l $i fs drivers/staging/lustre drivers/mtd ipc mm include/linux; done|sort|uniq|grep -v '^fs/namespace.c$')
sed -i -e 's/\<MS_RDONLY\>/SB_RDONLY/g' \
-e 's/\<MS_NOSUID\>/SB_NOSUID/g' \
-e 's/\<MS_NODEV\>/SB_NODEV/g' \
-e 's/\<MS_NOEXEC\>/SB_NOEXEC/g' \
-e 's/\<MS_SYNCHRONOUS\>/SB_SYNCHRONOUS/g' \
-e 's/\<MS_MANDLOCK\>/SB_MANDLOCK/g' \
-e 's/\<MS_DIRSYNC\>/SB_DIRSYNC/g' \
-e 's/\<MS_NOATIME\>/SB_NOATIME/g' \
-e 's/\<MS_NODIRATIME\>/SB_NODIRATIME/g' \
-e 's/\<MS_SILENT\>/SB_SILENT/g' \
-e 's/\<MS_POSIXACL\>/SB_POSIXACL/g' \
-e 's/\<MS_KERNMOUNT\>/SB_KERNMOUNT/g' \
-e 's/\<MS_I_VERSION\>/SB_I_VERSION/g' \
-e 's/\<MS_LAZYTIME\>/SB_LAZYTIME/g' \
$list
and commit it with something along the lines of 'convert filesystems
away from use of MS_... constants' as commit message, it would save a
quite a bit of headache next cycle"
* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
VFS: Differentiate mount flags (MS_*) from internal superblock flags
VFS: Convert sb->s_flags & MS_RDONLY to sb_rdonly(sb)
vfs: Add sb_rdonly(sb) to query the MS_RDONLY flag on s_flags
Pull more set_fs removal from Al Viro:
"Christoph's 'use kernel_read and friends rather than open-coding
set_fs()' series"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: unexport vfs_readv and vfs_writev
fs: unexport vfs_read and vfs_write
fs: unexport __vfs_read/__vfs_write
lustre: switch to kernel_write
gadget/f_mass_storage: stop messing with the address limit
mconsole: switch to kernel_read
btrfs: switch write_buf to kernel_write
net/9p: switch p9_fd_read to kernel_write
mm/nommu: switch do_mmap_private to kernel_read
serial2002: switch serial2002_tty_write to kernel_{read/write}
fs: make the buf argument to __kernel_write a void pointer
fs: fix kernel_write prototype
fs: fix kernel_read prototype
fs: move kernel_read to fs/read_write.c
fs: move kernel_write to fs/read_write.c
autofs4: switch autofs4_write to __kernel_write
ashmem: switch to ->read_iter
General updates:
* Constify pci_device_id in various drivers
* Constify device_type
* Remove pad control code from the Gemini driver
* Use %pOF to print OF node full_name
* Various fixes in the physmap_of driver
* Remove unused vars in mtdswap
* Check devm_kzalloc() return value in the spear_smi driver
* Check clk_prepare_enable() return code in the st_spi_fsm driver
* Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
* add support to the JEDEC JESD216B specification (SFDP tables).
* add support to the Intel Denverton SPI flash controller.
* fix error recovery for Spansion/Cypress SPI NOR memories.
* fix 4-byte address management for the Aspeed SPI controller.
* add support to some Microchip SST26 memory parts
* remove unneeded pinctrl header Write a message for tag:
-----BEGIN PGP SIGNATURE-----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=UgCd
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"General updates:
- Constify pci_device_id in various drivers
- Constify device_type
- Remove pad control code from the Gemini driver
- Use %pOF to print OF node full_name
- Various fixes in the physmap_of driver
- Remove unused vars in mtdswap
- Check devm_kzalloc() return value in the spear_smi driver
- Check clk_prepare_enable() return code in the st_spi_fsm driver
- Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
- Fix memory leaks in the core
- Remove unused NAND locking support
- Rename nand.h into rawnand.h (preparing support for spi NANDs)
- Use NAND_MAX_ID_LEN where appropriate
- Fix support for 20nm Hynix chips
- Fix support for Samsung and Hynix SLC NANDs
- Various cleanup, improvements and fixes in the qcom driver
- Fixes for bugs detected by various static code analysis tools
- Fix mxc ooblayout definition
- Add a new part_parsers to tmio and sharpsl platform data in order
to define a custom list of partition parsers
- Request the reset line in exclusive mode in the sunxi driver
- Fix a build error in the orion-nand driver when compiled for ARMv4
- Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header Write a message for tag:"
* tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd: (74 commits)
mtd: nand: complain loudly when chip->bits_per_cell is not correctly initialized
mtd: nand: make Samsung SLC NAND usable again
mtd: nand: tmio: Register partitions using the parsers
mfd: tmio: Add partition parsers platform data
mtd: nand: sharpsl: Register partitions using the parsers
mtd: nand: sharpsl: Add partition parsers platform data
mtd: nand: qcom: Support for IPQ8074 QPIC NAND controller
mtd: nand: qcom: support for IPQ4019 QPIC NAND controller
dt-bindings: qcom_nandc: IPQ8074 QPIC NAND documentation
dt-bindings: qcom_nandc: IPQ4019 QPIC NAND documentation
dt-bindings: qcom_nandc: fix the ipq806x device tree example
mtd: nand: qcom: support for different DEV_CMD register offsets
mtd: nand: qcom: QPIC data descriptors handling
mtd: nand: qcom: enable BAM or ADM mode
mtd: nand: qcom: erased codeword detection configuration
mtd: nand: qcom: support for read location registers
mtd: nand: qcom: support for passing flags in DMA helper functions
mtd: nand: qcom: add BAM DMA descriptor handling
mtd: nand: qcom: allocate BAM transaction
mtd: nand: qcom: DMA mapping support for register read buffer
...
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas, megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJZscDNAAoJEAVr7HOZEZN4DWIQAK/UkkrvKpV/jLATM/yi7CoL
QidY86Hmwwl7A9HQ+2fjLfAsye0xcCzRwkucKK90IP5b4pefHhiJJfiMKAAe3TUW
xstnY5z5jaOhDG4nyJFoSm5fH5qXkMnJ8NZRK8f6Qg5yBN5dStEKqoBboNsz4KBI
md7idw0mbp5i2GXlJwSpc5eDS97GiPL6WkwgGaGKfXF1NDau0GbEdjijfz55haCD
pMhY7WJh/71RfOq/1ThXT1Z3khOlVcKXrkdO+602n7zh/klRBRtBC8m2a6xCfZPj
n7Pb/s0jhCQPd+e/Xtv7WEbY8uNOCrGoVgZ6U5EGrT5IeTfep24ackYqerjMhE63
esi4BJY8lUP9SGleLMgjYWyCHdmxBJRa7UI614DWN/H0QoGP6j/2EzGoi5Fw04vC
H8/+aqPPWZc9KUBioRYo8xWO8YgMqL2eyXY+Tc9cwxqAe2T6k/NC1zJVgDFKXfzb
QoWW4v9NNmYwf5vL/7tNgkeTMFQV66yUR7dR3SGTSk8UIrJ40ok0JyUAsDg86ZAH
BfMkWwhWQ6Byoel0Y7Ti88T49Cox/64r/I0ux06Qgg99+KpRLT7z20+GLIEHgXxg
116C39rgvYKqzc7W8RCyj8qSROuMVzg6QFbB6n+1PEsYIX2O8A2Re3jdS34q2LbX
aBDm/Lfdl4kkJrV9xY6P
=nQUG
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: scsi-mq: Always unprepare before requeuing a request
scsi: Show .retries and .jiffies_at_alloc in debugfs
scsi: Improve requeuing behavior
scsi: Call scsi_initialize_rq() for filesystem requests
scsi: qla2xxx: Reset the logo flag, after target re-login.
scsi: qla2xxx: Fix slow mem alloc behind lock
scsi: qla2xxx: Clear fc4f_nvme flag
scsi: qla2xxx: add missing includes for qla_isr
scsi: qla2xxx: Fix an integer overflow in sysfs code
scsi: aacraid: report -ENOMEM to upper layer from aac_convert_sgraw2()
scsi: aacraid: get rid of one level of indentation
scsi: aacraid: fix indentation errors
scsi: storvsc: fix memory leak on ring buffer busy
scsi: scsi_transport_sas: switch to bsg-lib for SMP passthrough
scsi: smartpqi: remove the smp_handler stub
scsi: hpsa: remove the smp_handler stub
scsi: bsg-lib: pass the release callback through bsg_setup_queue
scsi: Rework handling of scsi_device.vpd_pg8[03]
scsi: Rework the code for caching Vital Product Data (VPD)
scsi: rcu: Introduce rcu_swap_protected()
...
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZsSBoAAoJEAhfPr2O5OEVDc4QAJZSuVYmyLgvtmPxhyqgCvkz
I0DmWM4ZtK2VT/xJ/AA23z8IiLKi2+pDC0Xx6/aIiA665cyl3oPUdkKIaHW9Z6+A
fV8gSFkmGkluQb9mP/KdHYI2oSeEv2ivCa1kfaApYcoBa904z8uU++z15Iu5p/+m
fjpc2vnc9rax0Vuwmgv7p1CL4j4e/ja0siCSCGbu2ad50KqP4ytnBooNPQOQt89D
L+Av5MeGml/CTUUnAFjWfSmQ72Ht8GhoBBKc6wGoq9x3GTckDDTqy8BAqGt4UQnu
fR0mb71zuSVmTjxRe7tc/74m3ReaeSHzQeHJhjdQslvNmV3RVQgk/6CCsmqNEegr
rbC3glQCM+gp5YywCjRL6DCPsoqvjexLtPQjMZIGYxgSYQUyXGOxilgmj9+73761
6aOl0nqdgN+vlWzaSeDF9EQxRsc+cCq/Po8/xuPE/Pzs6zTQwU+6b+ADLf9jCyDP
LTC49wOj24SoWiTlG1FTct2ogZ3h5wNPWlurBtmyiFJn+43RpsH5IW9wLilCjeiE
6JeCWEIBglCCq/TVCzETKNSaixDL6/lMQ9uRdCpIO4VLyoS6S9pZASNPBmQ1h7h/
oTjYDeWirIthNOccstbBoJQYSX62CqAIW3wq5ME6PAgM+ioiLXLYk0fV3yBKoBNW
Z0SBeTcuPxWmfzuxMtik
=fNM2
-----END PGP SIGNATURE-----
Merge tag 'media/v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Brazil's Independence Day pull request :-)
This is one of the biggest media pull requests, with 625 patches
affecting almost all parts of media (RC, DVB, V4L2, CEC, docs).
This contains:
- A lot of new drivers:
* DVB frontends: mxl5xx, stv0910, stv6111;
* camera flash: as3645a led driver;
* HDMI receiver: adv748X;
* camera sensor: Omnivision 6650 5M driver (ov6650);
* HDMI CEC: ao-cec meson driver;
* V4L2: Qualcom camss driver;
* Remote controller: gpio-ir-tx, pwm-ir-tx and zx-irdec drivers.
- The DDbridge DVB driver got a massive update, with makes it in sync
with modern hardware from that vendor;
- There's an important milestone on this series: the DVB
documentation was written in 2003, but only started to be updated
in 2007. It also used to contain several gaps from the time it was
kept out of tree, mentioning error codes and device nodes that
never existed upstream. On this series, it received a massive
update: all non-deprecated digital TV APIs are now in sync with the
current implementation;
- Some DVB APIs that aren't used by any upstream driver got removed;
- Other parts of the media documentation algo got updated, fixing
some bugs on its PDF output and making it compatible with Sphinx
version 1.6.
As the number of hacks required to build PDF output reduced, I hope
we'll have less troubles as newer versions of our documentation
toolchain are released (famous last words);
- As usual, lots of driver cleanups and improvements"
* tag 'media/v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (624 commits)
media: leds: as3645a: add V4L2_FLASH_LED_CLASS dependency
media: get rid of removed DMX_GET_CAPS and DMX_SET_SOURCE leftovers
media: Revert "[media] v4l: async: make v4l2 coexist with devicetree nodes in a dt overlay"
media: staging: atomisp: sh_css_calloc shall return a pointer to the allocated space
media: Revert "[media] lirc_dev: remove superfluous get/put_device() calls"
media: add qcom_camss.rst to v4l-drivers rst file
media: dvb headers: make checkpatch happier
media: dvb uapi: move frontend legacy API to another part of the book
media: pixfmt-srggb12p.rst: better format the table for PDF output
media: docs-rst: media: Don't use \small for V4L2_PIX_FMT_SRGGB10 documentation
media: index.rst: don't write "Contents:" on PDF output
media: pixfmt*.rst: replace a two dots by a comma
media: vidioc-g-fmt.rst: adjust table format
media: vivid.rst: add a blank line to correct ReST format
media: v4l2 uapi book: get rid of driver programming's chapter
media: format.rst: use the right markup for important notes
media: docs-rst: cardlists: change their format to flat-tables
media: em28xx-cardlist.rst: update to reflect last changes
media: v4l2-event.rst: adjust table to fit on PDF output
media: docs: don't show ToC for each part on PDF output
...
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZrTy3AAoJEAAOaEEZVoIVaucP/ApBAj2S5wzvlV1u6l8E6ae7
ZeEEZfcWwzRYlKjZAkTWqj9XvGpDGO5gLq4wsZK2edFAq++/MJF8ZVtN4tdZ1kUZ
DUvRodtVOrT08Kp9wZXGT7JOFrf6U/6gMcR6p0MuWnHndeKYvlpcFi9NPT4EC9/z
Zm9V7gtlPdSOha7eaSjUS0+vLERkxqXLBW3Av9QUOBP/lbI3lqIroGKeHDYnVdya
2P/k5EcRRJMyJP6TqyYxmmJl+UWjJFMLvnlUDBslHnD/u3mIUhw3JLHYBjn5dZRE
Xjq56IDPoXDUvzlBhtn/Uqyx+/wtwsNsylpmKv6K5G1JfdeuSsPVsCey+A1cqV64
LpE5896wf9TmnmI9LNyh6vDn925xPSGBiF45UEp5f9aO7jXeY0MaEZ8g+ENqFIDK
v4gtZdS9FhYHV+/l4qEwYMKrqSbwKEs1r1FT+f4wnABby1ojfdA57ZPlp5PV2Vjp
szTp88Zkb7cMvZwEnWwxWofcJNmgS7uNahvnQF3IJ4ITsioEkuyYR3K4ZQMaaaV9
wCp6G0FhXZaK3OI7o9WiDwaO2elp9Hxc8bnqKpiBbHZkY0NLh7/++5VxpeNbTHFy
AGijQiiKGNNyYqNj93wq9jpVdMNjB0pXrHRxfav8v7MtQ+WfbEoAENF4T7hN7iXn
UuF6eSWEC5O1UCRUk1A+
=LLY3
-----END PGP SIGNATURE-----
Merge tag 'wberr-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull writeback error handling updates from Jeff Layton:
"This pile continues the work from last cycle on better tracking
writeback errors. In v4.13 we added some basic errseq_t infrastructure
and converted a few filesystems to use it.
This set continues refining that infrastructure, adds documentation,
and converts most of the other filesystems to use it. The main
exception at this point is the NFS client"
* tag 'wberr-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
ecryptfs: convert to file_write_and_wait in ->fsync
mm: remove optimizations based on i_size in mapping writeback waits
fs: convert a pile of fsync routines to errseq_t based reporting
gfs2: convert to errseq_t based writeback error reporting for fsync
fs: convert sync_file_range to use errseq_t based error-tracking
mm: add file_fdatawait_range and file_write_and_wait
fuse: convert to errseq_t based error tracking for fsync
mm: consolidate dax / non-dax checks for writeback
Documentation: add some docs for errseq_t
errseq: rename __errseq_set to errseq_set
-----BEGIN PGP SIGNATURE-----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=VPMU
-----END PGP SIGNATURE-----
Merge tag 'locks-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull file locking updates from Jeff Layton:
"This pile just has a few file locking fixes from Ben Coddington. There
are a couple of cleanup patches + an attempt to bring sanity to the
l_pid value that is reported back to userland on an F_GETLK request.
After a few gyrations, he came up with a way for filesystems to
communicate to the VFS layer code whether the pid should be translated
according to the namespace or presented as-is to userland"
* tag 'locks-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: restore a warn for leaked locks on close
fs/locks: Remove fl_nspid and use fs-specific l_pid for remote locks
fs/locks: Use allocation rather than the stack in fcntl_getlk()
Here is the big staging and IIO driver update for 4.14-rc1.
Lots of staging driver fixes and cleanups, including some reorginizing
of the lustre header files to try to impose some sanity on what is, and
what is not, the uapi for that filesystem.
There are some tty core changes in here as well, as the speakup drivers
need them, and that's ok with me, they are sane and the speakup code is
getting nicer because of it.
There is also the addition of the obiligatory new wifi driver, just
because it has been a release or two since we added our last one...
Other than that, lots and lots of small coding style fixes, as usual.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWa2AbA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymboACfUsNhw+cJlVb25J70NULkye3y1PAAoJ+Ayq30
ckkLGakZayKcYEx50ffH
=KJwg
-----END PGP SIGNATURE-----
Merge tag 'staging-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and IIO driver update for 4.14-rc1.
Lots of staging driver fixes and cleanups, including some reorginizing
of the lustre header files to try to impose some sanity on what is,
and what is not, the uapi for that filesystem.
There are some tty core changes in here as well, as the speakup
drivers need them, and that's ok with me, they are sane and the
speakup code is getting nicer because of it.
There is also the addition of the obiligatory new wifi driver, just
because it has been a release or two since we added our last one...
Other than that, lots and lots of small coding style fixes, as usual.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (612 commits)
staging:rtl8188eu:core Fix remove unneccessary else block
staging: typec: fusb302: make structure fusb302_psy_desc static
staging: unisys: visorbus: make two functions static
staging: fsl-dpaa2/eth: fix off-by-one FD ctrl bitmaks
staging: r8822be: Simplify deinit_priv()
staging: r8822be: Remove some dead code
staging: vboxvideo: Use CONFIG_DRM_KMS_FB_HELPER to check for fbdefio availability
staging:rtl8188eu Fix comparison to NULL
staging: rts5208: rename mmc_ddr_tunning_rx_cmd to mmc_ddr_tuning_rx_cmd
Staging: Pi433: style fix - tabs and spaces
staging: pi433: fix spelling mistake: "preample" -> "preamble"
staging:rtl8188eu:core Fix Code Indent
staging: typec: fusb302: Export current-limit through a power_supply class dev
staging: typec: fusb302: Add support for USB2 charger detection through extcon
staging: typec: fusb302: Use client->irq as irq if set
staging: typec: fusb302: Get max snk mv/ma/mw from device-properties
staging: typec: fusb302: Set max supply voltage to 5V
staging: typec: tcpm: Add get_current_limit tcpc_dev callback
staging:rtl8188eu Use __func__ instead of function name
staging: lustre: coding style fixes found by checkpatch.pl
...
The calloc function returns either a null pointer or a pointer to the
allocated space. Add the second case that is missed.
Fixes: da22013f7d ("atomisp: remove indirection from sh_css_malloc")
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of playing games with the address limit. This also gains
us proper usage of the write counter, time stamp updates and kvec
validation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
And use the proper VFS helper for using the backing file.
Also make sure we hold ashmem_lock while updating f_pos to make sure that
it's not racy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----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=5fxW
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.14' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.14 merge window.
I'm sending this early, as my continuing journey into fatherhood is
occurring really soon now, I'm going to be mostly useless for the next
couple of weeks, though I may be able to read email, I doubt I'll be
doing much patch applications or git sending. If anything urgent pops
up I've asked Daniel/Jani/Alex/Sean to try and direct stuff towards
you.
Outside drm changes:
Some rcar-du updates that touch the V4L tree, all acks should be in
place. It adds one export to the radix tree code for new i915 use
case. There are some minor AGP cleanups (don't see that too often).
Changes to the vbox driver in staging to avoid breaking compilation.
Summary:
core:
- Atomic helper fixes
- Atomic UAPI fixes
- Add YCBCR 4:2:0 support
- Drop set_busid hook
- Refactor fb_helper locking
- Remove a bunch of internal APIs
- Add a bunch of better default handlers
- Format modifier/blob plane property added
- More internal header refactoring
- Make more internal API names consistent
- Enhanced syncobj APIs (wait/signal/reset/create signalled)
bridge:
- Add Synopsys Designware MIPI DSI host bridge driver
tiny:
- Add Pervasive Displays RePaper displays
- Add support for LEGO MINDSTORMS EV3 LCD
i915:
- Lots of GEN10/CNL support patches
- drm syncobj support
- Skylake+ watermark refactoring
- GVT vGPU 48-bit ppgtt support
- GVT performance improvements
- NOA change ioctl
- CCS (color compression) scanout support
- GPU reset improvements
amdgpu:
- Initial hugepage support
- BO migration logic rework
- Vega10 improvements
- Powerplay fixes
- Stop reprogramming the MC
- Fixes for ACP audio on stoney
- SR-IOV fixes/improvements
- Command submission overhead improvements
amdkfd:
- Non-dGPU upstreaming patches
- Scratch VA ioctl
- Image tiling modes
- Update PM4 headers for new firmware
- Drop all BUG_ONs.
nouveau:
- GP108 modesetting support.
- Disable MSI on big endian.
vmwgfx:
- Add fence fd support.
msm:
- Runtime PM improvements
exynos:
- NV12MT support
- Refactor KMS drivers
imx-drm:
- Lock scanout channel to improve memory bw
- Cleanups
etnaviv:
- GEM object population fixes
tegra:
- Prep work for Tegra186 support
- PRIME mmap support
sunxi:
- HDMI support improvements
- HDMI CEC support
omapdrm:
- HDMI hotplug IRQ support
- Big driver cleanup
- OMAP5 DSI support
rcar-du:
- vblank fixes
- VSP1 updates
arcgpu:
- Minor fixes
stm:
- Add STM32 DSI controller driver
dw_hdmi:
- Add support for Rockchip RK3399
- HDMI CEC support
atmel-hlcdc:
- Add 8-bit color support
vc4:
- Atomic fixes
- New ioctl to attach a label to a buffer object
- HDMI CEC support
- Allow userspace to dictate rendering order on submit ioctl"
* tag 'drm-for-v4.14' of git://people.freedesktop.org/~airlied/linux: (1074 commits)
drm/syncobj: Add a signal ioctl (v3)
drm/syncobj: Add a reset ioctl (v3)
drm/syncobj: Add a syncobj_array_find helper
drm/syncobj: Allow wait for submit and signal behavior (v5)
drm/syncobj: Add a CREATE_SIGNALED flag
drm/syncobj: Add a callback mechanism for replace_fence (v3)
drm/syncobj: add sync obj wait interface. (v8)
i915: Use drm_syncobj_fence_get
drm/syncobj: Add a race-free drm_syncobj_fence_get helper (v2)
drm/syncobj: Rename fence_get to find_fence
drm: kirin: Add mode_valid logic to avoid mode clocks we can't generate
drm/vmwgfx: Bump the version for fence FD support
drm/vmwgfx: Add export fence to file descriptor support
drm/vmwgfx: Add support for imported Fence File Descriptor
drm/vmwgfx: Prepare to support fence fd
drm/vmwgfx: Fix incorrect command header offset at restart
drm/vmwgfx: Support the NOP_ERROR command
drm/vmwgfx: Restart command buffers after errors
drm/vmwgfx: Move irq bottom half processing to threads
drm/vmwgfx: Don't use drm_irq_[un]install
...
This patch removes the unwanted braces and else statement inside the
function 'SecIsInPMKIDList'
Signed-off-by: Janani Sankara Babu <jananis37@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The const structure fusb302_psy_desc is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warnings
symbol 'fusb302_psy_desc' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions sig_queue_offset and sig_data_offset are local to
the source and do not need to be in global scope, so make them
static.
Cleans up sparse warnings:
symbol 'sig_queue_offset' was not declared. Should it be static?
symbol 'sig_data_offset' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the values of DPAA2_FD_CTRL_FSE and DPAA2_FD_CTRL_FAERR,
which are shifted off by one bit.
Fixes: 39163c0ce0 ("staging: fsl-dpaa2/eth: Errors checking update")
Cc: <stable@vger.kernel.org>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
-----BEGIN PGP SIGNATURE-----
iQJABAABCAAqBQJZpwMZIxxib3Jpcy5icmV6aWxsb25AZnJlZS1lbGVjdHJvbnMu
Y29tAAoJEGXtNgF+CLcAJEoP/jRnEjPznWT3+ngw6k/rnykkn/wexKV3iyX/6b71
MQT/ZFuT3HsHnUjyprPvyRWJeKun6XyIH5fk7FlXIei9TaWCt6/UGTKousaPKeR2
maggGeEjxGVpHJM/jpIYCyjt83zpezBqTupv52XhXxPaU7ROSpuHCd92YcPzIaT5
tcn8JrI7TGuGlBrBbA2y8ZrPtuug3IKqUfpIiQmoqr0jzQR+AbZKHg0kk5a8piOn
OguK67uhxeOvq831bGPehCPDbuE0loNi4CssayJ1HrisfS95kH/cqrveapgKsUG/
fxaHh1i65I0lxa8sgUgeUiU04Zsy1YcgNbCj41AY4AHnjJ0+Qp1cV6KAB/x5/wH9
ES/fW06how+1BLEeLvOr+rIQ41WeP0qV2H3r/PtkeswKKAV3gSERBXVHmg1E7Yum
HkmPqzhu+nSk3mP7p3yxpd7EwWQh2xpvVYrfQ5vQbtdfm8Uw9n6S8x+O89ch9wWi
+KbMWFsmF78nuRWW3WTsaiOFKcTRLBT5RoU2z4i9hCvQT2Pnx3SBhHrIj6xqBI1S
8MpeDdlXHmRQfZxj+jDqU77JYqVEmy/5it9OjhjMpOqxfCf4K6Nlb75TEdR5Nh/9
BA1qqTBEslg3UqS8ofGFHGFZWrW3JHf02SYo2zU9IvBninh3HrqHiFhBc3p1xNDE
7GwD
=bC1+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.14' of git://git.infradead.org/l2-mtd into mtd/next
From Boris:
"
This pull request contains the following core changes:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
"
Now that the extraneous debugging code is removed, routine deinit_priv()
clearly contains code that serves no useful purpose.
A null test before a call to kfree() and a spurious cast are also removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code found inside an #ifdef CONFIG_RTL_DEBUG ... #endif section
is left over from debugging of the original driver, and should be
deleted.
Reported by: Andreas Ziegler <andreas.ziegler@fau.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking for CONFIG_FB_DEFERRED_IO is not the right thing to do since
the fbdev code may be built as a module while vboxvideo is builtin.
This can only happen when DRM_KMS_FB_HELPER is not set:
a) DRM_VBOXVIDEO selects DRM_KMS_HELPER
b) DRM_KMS_FB_HELPER depends on DRM_KMS_HELPER
c) DRM_KMS_FB_HELPER selects FB_DEFERRED_IO
So when DRM_KMS_FB_HELPER is set and vboxvideo is builtin then
FB_DEFERRED_IO must be builtin too.
This commit moves the #ifdefs around fbdefio code over to
CONFIG_DRM_KMS_FB_HELPER, as other drm drivers already do, fixing:
drivers/staging/vboxvideo/vbox_fb.o: In function `vbox_fbdev_fini':
vbox_fb.c:(.text+0x36): undefined reference to `fb_deferred_io_cleanup'
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the comparison of variable say x to NULL with '!x'
signed-off-by: Janani Sankara Babu <jananis37@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trival fix to spelling mistake in function name
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch solves the code indentation issue inside the if block
Signed-off-by: Janani Sankara Babu <jananis37@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fusb302 Type-C port-controller cannot control the current-limit
directly, so we need to exported the limit so that another driver
(e.g. the charger driver) can pick the limit up and configure the
system accordingly.
The power-supply subsys already provides infrastructure for this,
power-supply devices have the notion of being supplied by another
power-supply and have properties through which we can export the
current-limit.
Register a power_supply and export the current-limit through the
power_supply's current-max property.
Cc: "Yueyao (Nathan) Zhu" <yueyao@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fusb302 port-controller relies on an external device doing USB2
charger-type detection.
The Intel Whiskey Cove PMIC with which the fusb302 is combined on some
X86/ACPI platforms already has a charger-type detection driver which
uses extcon to communicate the detected charger-type.
Rather then inventing a new API for USB2 charger-type detection
specifically for use with the tcpm code, this commit simply re-uses the
existing extcon API and uses that do USB2 charger detection.
Note that the "fcs,extcon-name" property name is only for kernel internal
use by X86/ACPI platform code and as such is NOT documented in
the fusb302 devicetree bindings.
Cc: "Yueyao (Nathan) Zhu" <yueyao@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fusb302 is also used on x86 systems where the platform code sets
the irq in client->irq and there is no gpio named fcs,int_n.
Cc: "Yueyao (Nathan) Zhu" <yueyao@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is board specific info so it should come from board config, such
as devicetree.
I've chosen to prefix these with "fcs," treating them as fusb302 driver
specific for now. We may want to revisit this and replace these with
properties which are part of a (to be written) generic type-c controller
devicetree binding.
Since this commit adds new dt-properties it also adds devicetree-bindings
documentation (which so far was absent for the fusb302 driver).
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: "Yueyao (Nathan) Zhu" <yueyao@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anything higher then 5V may damage hardware not capable of it, so
the only sane default here is 5V. If a board is able to handle a
higher voltage that should come from board specific data such as
device-tree and not be hard coded into the fusb302 code.
Cc: "Yueyao (Nathan) Zhu" <yueyao@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A Rp signalling the default current limit indicates that we're possibly
connected to an USB2 power-source. In some cases the type-c port-controller
may provide the capability to detect the current-limit in this case,
through e.g. BC1.2 detection.
This commit adds an optional get_current_limit tcpc_dev callback which
allows the port-controller to provide current-limit detection for when
the CC pin is pulled up with Rp.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes use of predefined identifier __func__ inorder to clear
the warning: Prefer using '"%s...", __func__' to using 'update_bmc_sta',
this function's name, in a string
Signed-off-by: Janani Sankara Babu <jananis37@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch removes "WARNING: Prefer using '"%s...", __func__'
to using 'xxxxxxxx', this function's name, in a string" warnings
reported by checkpatch.pl script.
Signed-off-by: Simo Koskinen <koskisoft@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed paranthesis alignment for compliance with checkpatch.
Signed-off-by: Edvard Holst <edvard.holst@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changing pr_err to dev_err in visor_check_channel. Added device
as an argument to visor_check_channel to pass into dev_err.
Signed-off-by: Sameer Wadgaonkar <sameer.wadgaonkar@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Reviewed-by: Tim Sell <timothy.sell@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing EXPORT_SYMBOL_GPU from visor_check_channel since it is
used only in visorbus.
Signed-off-by: Sameer Wadgaonkar <sameer.wadgaonkar@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Reviewed-by: Tim Sell <timothy.sell@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up the GUID definition to remove some checkpatch warnings as well as
using the whole width of the screen.
Signed-off-by: David Kershner <david.kershner@unisys.com>
Reviewed-by: Tim Sell <timothy.sell@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
