Device tree clock binding document for EMMA Mobile EV2 SMU,
And Common clock framework based implementation of it.
Following nodes are defined to describe clock tree.
- renesas,emev2-smu
- renesas,emev2-smu-clkdiv
- renesas,emev2-smu-gclk
These bindings are designed manually based on
19UH0037EJ1000_SMU : System Management Unit User's Manual
So far, reparent is not implemented, and is fixed to index #0.
Clock tree description is not included, and should be provided
by device-tree.
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MSTP clocks are gate clocks controlled through a register that handles
up to 32 clocks. The register is often sparsely populated.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
DIV6 clocks are divider gate clocks controlled through a single
register. The divider is expressed on 6 bits, hence the name, and can
take values from 1/1 to 1/64.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The R-Car Gen2 SoCs (R8A7790 and R8A7791) have several clocks that are
too custom to be supported in a generic driver. Those clocks can be
divided in two categories:
- Fixed rate clocks with multiplier and divisor set according to boot
mode configuration
- Custom divider clocks with SoC-specific divider values
This driver supports both.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This AT91 specific Kconfig option removed the code that dealt with
programmable clocks. Each AT91 SoC embeds programmable clocks and
there is little gain to remove this code in case that such a clock
is not used.
If this option is not selected, it causes certain drivers to fail
to build. We simply remove this option instead of adding code just
to build a workaround.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The "pcie_xclk" clock is not actually a clock at all, but rather a reset
domain. Now that the custom Tegra module reset API has been removed, we
can remove the definition of any "clocks" that existed solely to support
it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Now that no code uses the custom Tegra module reset API, we can remove
its implementation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
The Tegra CAR module implements both a clock and reset controller. So
far, the driver exposes the clock feature via the common clock API and
the reset feature using a custom API. This patch adds an implementation
of the common reset framework API (include/linux/reset*.h). The legacy
reset implementation will be removed once all drivers have been
converted.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch fixes Keystone gate control clock driver initialization path:
1) clk_register_psc() returns error code and not a pure pointer, hence
its return value need to be checked using IS_ERR(clk) macro.
2) Mapped IO memory isn't unmapped in case of errors, hence fix it.
Cc: Mike Turquette <mturquette@linaro.org
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
DDR3A/B, ARM and PA PLL controllers have clkod register bits for
configuring postdiv values. So use it instead of using fixed
post dividers for these pll controllers. Assume that if fixed-postdiv
attribute is not present, use clkod register value for pistdiv.
Also update the Documentation of bindings to reflect the same.
Cc: Mike Turquette <mturquette@linaro.org
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Fixes cpll control and lock register offset values for Exynos5420 SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_unregister() is currently not implemented and it is required when
a clock provider module needs to be unloaded.
Normally the clock supplier module is prevented to be unloaded by
taking reference on the module in clk_get().
For cases when the clock supplier module deinitializes despite the
consumers of its clocks holding a reference on the module, e.g. when
the driver is unbound through "unbind" sysfs attribute, there are
empty clock ops added. These ops are assigned temporarily to struct
clk and used until all consumers release the clock, to avoid invoking
callbacks from the module which just got removed.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch adds common __clk_get(), __clk_put() clkdev helpers that
replace their platform specific counterparts when the common clock
API is used.
The owner module pointer field is added to struct clk so a reference
to the clock supplier module can be taken by the clock consumers.
The owner module is assigned while the clock is being registered,
in functions _clk_register() and __clk_register().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is currently a race condition in the device tree part of clk_get()
function, since the pointer returned from of_clk_get_by_name() may become
invalid before __clk_get() call. E.g. due to the clock provider driver
remove() callback being called in between of_clk_get_by_name() and
__clk_get().
Fix this by doing both the look up and __clk_get() operations with the
clock providers list mutex held. This ensures that the clock pointer
returned from __of_clk_get_from_provider() call and passed to __clk_get()
is valid, as long as the clock supplier module first removes its clock
provider instance and then does clk_unregister() on the corresponding
clocks.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add helper functions for the of_clk_providers list locking and
an unlocked variant of of_clk_get_from_provider().
These functions are intended to be used in the clkdev to avoid
race condition in the device tree based clock look up in clk_get().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable common clock driver of Hi3620 SoC. clkgate-seperated driver is
used to support the clock gate that enable/disable/status registers
are seperated.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
This patch adds at91 smd (Soft Modem) clock implementation using common clk
framework.
Not used by any driver right now.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 usb clock implementation using common clk framework.
This clock is used to clock usb ports (ohci, ehci and udc).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This adds new at91 utmi clock implementation using common clk framework.
This clock is a pll with a fixed factor (x40).
It is used as a source for usb clock.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 programmable clocks implementation using common clk
framework.
A programmable clock is a clock which can be exported on a given pin to clock
external devices.
Each programmable clock is given an id (from 0 to 8).
The number of available programmable clocks depends on the SoC you're using.
Programmable clock driver only implements the clock setting (clock rate and
parent setting). It must be chained to a system clock in order to
enable/disable the generated clock.
The PCKX pins used to output the clock signals must be assigned to the
appropriate peripheral (see atmel's datasheets).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 peripheral clock implementation using common clk
framework.
Almost all peripherals provided by at91 SoCs need a clock to work properly.
This clock is enabled/disabled using PCER/PCDR resgisters.
Each peripheral is given an id (see atmel's datasheets) which is used to
define and reference peripheral clocks.
Some new SoCs (at91sam9x5 and sama5d3) provide a new register (PCR) where you
can configure the peripheral clock as a division of the master clock.
This will help reducing the peripherals power comsumption.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 system clock implementation using common clk
framework.
Some peripherals need to enable a "system" clock in order to work properly.
Each system clock is given an id based on the bit position in SCER/SCDR
registers.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 master clock implementation using common clk
framework.
The master clock layout describe the MCKR register layout.
There are 2 master clock layouts:
- at91rm9200
- at91sam9x5
Master clocks are given characteristics:
- min/max clock output rate
These characteristics are checked during rate change to avoid
over/underclocking.
These characteristics are described in atmel's SoC datasheet in
"Electrical Characteristics" paragraph.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 pll clock implementation using common clk framework.
The pll clock layout describe the PLLX register layout.
There are four pll clock layouts:
- at91rm9200
- at91sam9g20
- at91sam9g45
- sama5d3
PLL clocks are given characteristics:
- min/max clock source rate
- ranges of valid clock output rates
- values to set in out and icpll fields for each supported output range
These characteristics are checked during rate change to avoid
over/underclocking.
These characteristics are described in atmel's SoC datasheet in
"Electrical Characteristics" paragraph.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 main oscillator clock implementation using common
clk framework.
If rate is not provided during clock registration it is calculated using
the slow clock (main clk parent in this case) rate and MCFR register.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds at91 PMC (Power Management Controller) base support.
All at91 clocks managed by the PMC unit will use this framework.
This framework provides the following fonctionalities:
- define a new struct at91_pmc to hide PMC internals (lock, PMC memory
mapping, irq domain, ...)
- read/write helper functions (pmc_read/write) to access PMC registers
- lock/unlock helper functions (pmc_lock/unlock) to lock/unlock access to
pmc registers
- a new irq domain and its associated irq chip to request PMC specific
interrupts (useful for clk prepare callbacks)
The PMC unit is declared as a dt clk provider (CLK_OF_DECLARE), and every
clk using this framework will declare a table of of_at91_clk_init_cb_t
and add it to the pmc_clk_ids table.
When the pmc dt clock setup function is called (by of_clk_init function),
it triggers the registration of every supported child clk (those matching
the definitions in pmc_clk_ids).
This patch copies at91_pmc_base (memory mapping) and at91sam9_idle
(function) from arch/arm/mach-at91/clock.c (which is not compiled if
COMMON_CLK_AT91 is enabled).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Those are mostly random fixes, except for one patch to the composite
clock that adds support for automatic reparenting.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=sWyX
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-3.13' of https://github.com/mripard/linux into clk-next-sunxi-rebase
Allwinner sunXi SoCs clock changes
Those are mostly random fixes, except for one patch to the composite
clock that adds support for automatic reparenting.
Conflicts:
drivers/clk/sunxi/clk-sunxi.c
In case of error, the function __clk_lookup() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
clk_round_rate() can be used by drivers to determine whether or not a
frequency is supported by the clock. The current Tegra clock driver
outputs an error message and a stacktrace when the requested rate isn't
supported. That's fine for clk_set_rate(), but it's confusing when all
the driver does is query whether or not a frequency is supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The function socfpga_clk_init() can support clocks that do not have a divider
register, but a fixed-divider that can be read from DTS. Therefore, the "reg"
property is not a failing condition for socfpga_clk_init().
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[Maybe the third time will be the charm. -Alex]
If CONFIG_COMMON_CLK_DEBUG is defined, clk_debug_create_one() is
called to populate a debugfs directory with a few entries that are
common for all clock types.
If an error happens after creating the first one debugfs_remove() is
called on the clock's directory. The problem with this is that no
cleanup is done on the debugfs files already created in that
directory, so the directory never actually gets removed. This
problem is silently ignored.
Fix this by calling debugfs_remove_recursive() instead. Reset the
clk->dentry field to null afterward, to ensure it can't be mistaken
as a valid pointer.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The low-power DSI clocks are used during host-driven transactions on the
DSI bus. Documentation recommends that they be children of PLLP and run
at a frequency of at least 52 MHz.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The clock for the PWM controller is slightly different from other
peripheral clocks on Tegra30. The clock source mux field start at
bit position 28 rather than 30.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are two GPUs on Tegra30 and each of them uses a separate clock, so
the secondary clock needs to be initialized in order for the gr3d module
to work properly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add disp1 and disp2 clocks to the clock initialization table. These
clocks are required for display and HDMI support.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding suspend/resume function for tegra_cpu_car_ops. We only save and
restore the setting of the clock of CoreSight. Other clocks still need
to be taken care by clock driver.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Hook the functions for CPU hotplug support. After the CPU is hot
unplugged, the flow controller will handle to clock gate the CPU clock.
But still need to implement an empty function to avoid warning message.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Tegra124 introduces a number of new peripheral clocks. This patch adds those
to the common peripheral clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra124 introduces a number of a new clocks. Introduce the corresponding
the IDs for them.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra124 has a clock which consists of a mux and a fractional divider.
Add support for this.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 has periph clocks which share the hw register. Hence locking is
required.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 has an extra bank of peripheral clock registers. Add it to the
generic peripheral clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
