Spin lock rds_ring->lock is used in poll routine, so other users should
use spin_lock_bh(). While posting rx buffers from netxen_nic_attach,
rds_ring->lock is not required, so cleaning it instead of fixing it by
spin_lock_bh().
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea: Fix synchronization between HW and SW send queue
When memory is added to / removed from a partition via the Memory DLPAR
mechanism, the eHEA driver has to do a couple of things to reflect the
memory change in its own IO address translation tables. This involves
stopping and restarting the HW queues.
During this operation, it is possible that HW and SW pointer into these
queues get out of sync. This results in a situation where packets that
are attached to a send queue are not transmitted immediately, but
delayed until further X packets have been put on the queue.
This patch detects such loss of synchronization, and resets the ehea
port when needed.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bnx2x version to 1.52.53-4
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY locking is required between two ports for some external PHYs. Since
initialization was done in the common init function (called only on the
first port initialization) rather than in the port init function, there
was in fact no PHY locking between the ports.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Atheros PCIe wireless cards handled by ath5k do require L0s disabled.
For distributions shipping with CONFIG_PCIEASPM (this will be enabled
by default in the future in 2.6.36) this will also mean both L1 and L0s
will be disabled when a pre 1.1 PCIe device is detected. We do know L1
works correctly even for all ath5k pre 1.1 PCIe devices though but cannot
currently undue the effect of a blacklist, for details you can read
pcie_aspm_sanity_check() and see how it adjusts the device link
capability.
It may be possible in the future to implement some PCI API to allow
drivers to override blacklists for pre 1.1 PCIe but for now it is
best to accept that both L0s and L1 will be disabled completely for
distributions shipping with CONFIG_PCIEASPM rather than having this
issue present. Motivation for adding this new API will be to help
with power consumption for some of these devices.
Example of issues you'd see:
- On the Acer Aspire One (AOA150, Atheros Communications Inc. AR5001
Wireless Network Adapter [168c:001c] (rev 01)) doesn't work well
with ASPM enabled, the card will eventually stall on heavy traffic
with often 'unsupported jumbo' warnings appearing. Disabling
ASPM L0s in ath5k fixes these problems.
- On the same card you would see a storm of RXORN interrupts
even though medium is idle.
Credit for root causing and fixing the bug goes to Jussi Kivilinna.
Cc: David Quan <David.Quan@atheros.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch handles the firmware loading properly
for device ID 7015.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use appropriate command (CMD_TRIGGER_SCAN_TO) instead of scan command
(CMD_SCAN) to configure trigger scan timeout.
This was broken in commit 3a98c30f3e8bb1f32b5bcb74a39647b3670de275.
This fix address the bug reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=16554
Cc: stable@kernel.org
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Yuri Kululin <ext-yuri.kululin@nokia.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs advertise that they may be HT40 capable in the capabilites
but the current operating channel configuration may be only HT20.
This causes disconnection as ath9k_htc sets WLAN_RC_40_FLAG despite
the AP operating in HT20 mode.
Hence set this flag only if the current channel configuration
is HT40 enabled.
Cc: stable@kernel.org
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The setting of SPI_DATA_POS depending on CONFIG_CAIF_SPI_SYNC
where inverted.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes rx_submit() return an error code, and makes some call sites
that care check the return value. This is important because it lets us properly
handle cases where the device isn't ready to handle URB submissions (e.g., when
it is autosuspended under some drivers); previously, we would attempt and fail
to submit URBs and reschedule ourselves to try and fail again. This patch is
against Linus's 2.6 repo commit 45d7f32c7a43cbb9592886d38190e379e2eb2226.
Signed-Off-By: Elizabeth Jones <ellyjones@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic_pci_info structs are 128 bytes so an array of 8 uses 1024 bytes.
That's a lot if you run with 4K stacks. I allocated them with kcalloc()
instead.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code we allocated memory conditionally and freed it in
the error handling unconditionally. It turns out that this function is
only called during initialization and "adapter->npars" and
"adapter->eswitch" are always NULL at the start of the function. I
removed those checks.
Also since I was cleaning things, I changed the error handling for
qlcnic_get_pci_info() and pulled everything in an indent level.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix phy.c kernel-doc notation:
Warning(drivers/net/phy/phy.c:313): No description found for parameter 'ifr'
Warning(drivers/net/phy/phy.c:313): Excess function parameter 'mii_data' description in 'phy_mii_ioctl'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wan/farsync.c: In function 'fst_intr_rx':
drivers/net/wan/farsync.c:1312: warning: cast to pointer from integer of different size
drivers/net/wan/farsync.c: In function 'do_bottom_half_tx':
drivers/net/wan/farsync.c:1407: warning: cast to pointer from integer of different size
The "skb" and "mem" arguments being passed here are DMA addresses
being programmed into the hardware registers, so pass them as the type
that they actually are. And use the correct printf formatting in
debug logging statements for these things to match the type change.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver will try to protect all frames,
which leads to a lot of odd things like sending an
RTS with a zeroed RA before multicast frames, which
is clearly bogus.
In order to fix all of this, we need to take a step
back and see what we need to achieve:
* we need RTS/CTS protection if requested by
the AP for the BSS, mac80211 tells us this
* in that case, CTS-to-self should only be
enabled when mac80211 tells us
* additionally, as a hardware workaround, on
some devices we have to protect aggregated
frames with RTS
To achieve the first two items, set up the RXON
accordingly and set the protection required flag
in the transmit command when mac80211 requests
protection for the frame.
To achieve the last item, set the rate-control
RTS-requested flag for all stations that we have
aggregation sessions with, and set the protection
required flag when sending aggregated frames (on
those devices where this is required).
Since otherwise bugs can occur, do not allow the
user to override the RTS-for-aggregation setting
from sysfs any more.
Finally, also clean up the way all these flags get
set in the driver and move everything into the
device-specific functions.
Cc: stable@kernel.org [2.6.35]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/libertas/cfg.o
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_scan_worker’:
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: ‘TASK_NORMAL’ undeclared (first use in this function)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: (Each undeclared identifier is reported only once
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: for each function it appears in.)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_cfg_connect’:
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘signal_pending’
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘schedule_timeout’
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 5f7aebd845a9d2ed42f36b7333579ec3534b4713.
Apparently, that PCI ID data was incorrectly taken from the subsystem
information. The actual ID matches another already known ID.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on patches from Sonny Rao and Milton Miller...
Combined the patches to fix up clean_tx_irq and clean_rx_irq.
The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.
In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.
The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.
This bug was found during stress testing and adding this barrier has
been shown to fix it. The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().
This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.
Previously Submitted to e1000-devel only for ixgbe
http://marc.info/?l=e1000-devel&m=126593062701537&w=3
We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.
CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause
a build error. This resolves the build error by wrapping
the fcoe.up in CONFIG_IXGBE_DCB ifdefs.
Also frames were being priority VLAN tagged even without DCB
enabled. This fixes this so that 8021Q priority tags are
only added with DCB actually enabled.
Reported-by: divya <dipraksh@linux.vnet.ibm.com>
Reported-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_is_locked() can return zero on some (UP?)
configurations because locks don't exist, and
that causes an endless amount of warnings. Use
lockdep_assert_held() instead, which has two
advantages:
1) it verifies the current task is holding
the lock or mutex
2) it compiles away completely when lockdep
is not enabled
Cc: stable@kernel.org [2.6.34+, maybe only parts of patch]
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX tracing code copies with the wrong length,
which will typically copy too little data. Fix
this by using the correct length variable.
Cc: stable@kernel.org [2.6.32+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With turned on hspa modem (Dell 5530 internal card) and activated usb auto
suspend, my system gets up 100 "usbnet_resume has delayed data" per
minute. I didnt noticed any pathological behaviour, so just drop
this message. if any objections, please at least change it to _DEBUG.
Signed-off-by: Christian Samsel <christian.samsel@rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this leftover TODO from the cfg80211 conversion by doing a scan
if cfg80211 didn't pass in the BSSID for us. Since the scan code
uses so much of the cfg80211_scan_request structure to build up the
firmware command, we just fake one when the scan request is triggered
internally. But we need to make sure that internal 'fake' cfg82011
scan request does not get back to cfg82011 via cfg80211_scan_done().
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs get pissy if you don't send the firmware the extended rates
in the association request's rates TLV. Found this on a Linksys
WRT54G v2; it denies association with status code 18 unless you
add the extended rates too. The old driver did this, but it got
lost in the cfg80211 conversion.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let's actually check the right field in the command response; and
if there aren't any reported BSSes, exit early with success.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I often use "ethtool -i" command to check what driver controls the
ehternet device. But because current virtio_net driver doesn't
support "ethtool -i", it becomes the following:
# ethtool -i eth3
Cannot get driver information: Operation not supported
This patch simply adds the "ethtool -i" support. The following is the
result when using the virtio_net driver with my patch applied to.
# ethtool -i eth3
driver: virtio_net
version: N/A
firmware-version: N/A
bus-info: virtio0
Personally, "-i" is one of the most frequently-used option, and most
network drivers support "ethtool -i", so I think virtio_net also
should do.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use ARRAY_SIZE)
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPP channel ops structure should be const.
Cleanup the declarations to use standard C99 format.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
free_netdev finally calls kfree which makes the contents
of ndev and priv (private data contained in ndev) invalid.
So iounmap should be called before free_netdev.
Cc: David S. Miller <davem@davemloft.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sriramakrishnan <srk@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82ca9341763107615a15da6e59b9535d49eb91c3 added scary looking
but harmless error messages. Make them clearer and make the
actual failure message show up with the same severity as the
harmless one.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If kzalloc() fails return with -ENOMEM from ipw2100_net_init() which is
called by register_netdev.
CC: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again -
mactime is always 0. This causes problems in IBSS mode.
ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed.
Without this patch the merge is triggered by each beacon received.
This can be recognized by the "beacon TSF higher than local TSF - IBSS
merge with BSSID" log message accompanying each beacon.
This problem was not completely fixed in commit
a6d2055b02dde1067075795274672720baadd3ca and is not a stable kernel fix.
It is solely intended for wireless-testing.
Signed-off-by: Jan Friedrich <jft@dev2day.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SMC2802W appears to work with p54pci.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: David Cozatt <olbrannon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
