This patch adds support for power regulators.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is related to re-init processing on suspend/resume.
When card is resuming, some register is reset. If card is removable,
maybe controller should be rescan for card. But if assume card is
non-removable, need to restore the old value at registers.
We store the value of FIFOTH at probe time and then restore it in
dw_mci_resume().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds quirks and capabilities to platdata.
Some cards don't use the CDn pin; in that case, we assume the card's
inserted. Some boards need other capabilities. So, we add capabilities
in the board's platdata.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently kunmap_atomic() doesn't take into account the offset, used
with kmap_atomic(). On platforms, where kunmap_atomic() is not a NOP,
this will lead to problems, when offset != 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
At power off, reset OCR mask to be the highest possible voltage
supported for the current mmc host.
This solves the re-initialization during the power up sequence.
The voltage may have been decreased due to the card accepts a lower
voltage than the voltage used during the initialization sequence.
We need to reset the voltage to by the host highest possible value
since according to specification the initialization must always be
done at high voltage.
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When using mmc_try_claim_host the corresponding release
function is mmc_do_release_host, which then also must
be exported.
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
During redetection of a SDIO card, a request for a new card RCA
was submitted to the card, but was then overwritten by the old RCA.
This caused the card to be deselected instead of selected when using
the incorrect RCA. This bug's been present since the "oldcard"
handling was introduced in 2.6.32.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Reviewed-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Pawel Wieczorkiewicz <pawel.wieczorkiewicz@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
count is only ever used by assigning to old_len if count == 0, and
then old_len isn't ever used at all. So, both are redundant. Fixes:
drivers/mmc/host/dw_mmc.c: In function ‘dw_mci_read_data_pio’:
drivers/mmc/host/dw_mmc.c:1034:32: warning: variable ‘old_len’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It can be worked around using a GPIO which will be done for i.MX later.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
dma_unmap_sg() already flushes the cache, I don't get what this
code is doing here.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (76 commits)
pch_uart: reference clock on CM-iTC
pch_phub: add new device ML7213
n_gsm: fix UIH control byte : P bit should be 0
n_gsm: add a documentation
serial: msm_serial_hs: Add MSM high speed UART driver
tty_audit: fix tty_audit_add_data live lock on audit disabled
tty: move cd1865.h to drivers/staging/tty/
Staging: tty: fix build with epca.c driver
pcmcia: synclink_cs: fix prototype for mgslpc_ioctl()
Staging: generic_serial: fix double locking bug
nozomi: don't use flush_scheduled_work()
tty/serial: Relax the device_type restriction from of_serial
MAINTAINERS: Update HVC file patterns
tty: phase out of ioctl file pointer for tty3270 as well
tty: forgot to remove ipwireless from drivers/char/pcmcia/Makefile
pch_uart: Fix DMA channel miss-setting issue.
pch_uart: fix exclusive access issue
pch_uart: fix auto flow control miss-setting issue
pch_uart: fix uart clock setting issue
pch_uart : Use dev_xxx not pr_xxx
...
Fix up trivial conflicts in drivers/misc/pch_phub.c (same patch applied
twice, then changes to the same area in one branch)
To support MMC aggressive clock gating the driver has to stop the
interface clock when the .set_ios() method is called with .clock == 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some TOSHIBA MMC cards only support sector addressing even though the
size is < 2GB. According to JEDEC Spec JESD84-A441-1 the ocr register
(bits 30, 29) determine byte/sector mode. Use them.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdio_reset sends a CMD52 to reset the sdio card. This is highly
recommended for sdio cards being reinitialized. Since we do not
know if the card is being reinitialized we just send the command.
SD/eMMC cards are supposed to ignore the CMD before the CMD0.
Document why we are doing this.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
This patch adds DDR mode support to dw_mmc.
If we set any bit in UHS_REG bit[16:31], the card of that slot is
supported for DDR mode. For example, if UHS_REG[16] is set, card
number 0 is DDR mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
drivers/mmc/host/via-sdmmc.c: In function ‘via_reset_pcictrl’:
drivers/mmc/host/via-sdmmc.c:805:8: warning: variable ‘addrbase’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Harald Welte <HaraldWelte@viatech.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Fixes:
drivers/mmc/host/cb710-mmc.c: In function ‘cb710_wait_while_busy’:
drivers/mmc/host/cb710-mmc.c:182:6: warning: variable ‘err’ set but not
used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
drivers/mmc/host/sdhci-pci.c: In function ‘sdhci_pci_probe_slot’:
drivers/mmc/host/sdhci-pci.c:913:18: warning: variable ‘addr’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This adds the mmc host driver for Freescale MXS-based SoC i.MX23/28.
The driver calls into mxs-dma via generic dmaengine api for both pio
and data transfer.
Thanks Chris Ball for the indentation patch.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This switches the mxcmmc driver to use the dmaengine API. Unlike
the old one this one is always present in the tree, even if no DMA
is implemented, hence we can remove all the #ifdefs in from the driver.
The driver automatically switches to PIO mode if no DMA support or no
suitable channel is available.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for 8-bit buswidth.
dw_mmc can use 8-bit buswidth and set to CTYPE_8BIT in card-type register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This variable doesn't seem to be used for anything after the
other patches so just drop it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the DMA-API you shall unmap the sglists with the same
sglist length as passed into the mapping function, not the
returned value from the mapping function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The host_sglen is now actually used to keep track of whether DMA
is active or not, so rename and retype it to bool.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the DMA-API you shall unmap the sglists with the same
sglist length as passed into the mapping function, not the
returned value from the mapping function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the new dmaengine helpers to make the code more readable.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes the following:
- It is perfectly legal for the dma_map_sg() to return fewer
entries than were passed in.
- Supply the returned numer of (possibly coalesced) entries to
the device_pre_slave_sg() function.
- Use the proper original sg_len when unmapping the sglist
in the error path.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
So we know the implementation and prototypes agree with each other.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The test file is created under debugfs, not sysfs. Also remove
the unnecessary default n.
Signed-off-by: Will Newton <will.newton@imgtec.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Setting this bit in the clock enable register will stop the clock
when the card is in the IDLE state.
Signed-off-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We need to run the card detect tasklet at the end of slot initialisation
as it is possible that a card has been inserted prior to boot, so we don't
see an insertion interrupt and now the card is sitting there inserted but
with no power to it.
Signed-off-by: Neil Jones <neil.jones@imgtec.com>
Signed-off-by: Will Newton <will.newton@imgtec.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently MMC_MXC driver can be selected by all i.MX devices.
Restrict its use only for the appropriate processors.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add two large sequential I/O performance tests:
35. Large sequential read into scattered pages
36. Large sequential write from scattered pages
The tests measure transfer times for 10MiB, 100MiB, 1000MiB.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Existing performance tests measure single or sequential I/O speed.
Add two random I/O tests:
33. Random read performance by transfer size
34. Random write performance by transfer size
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The test area size was set to the preferred erase size but for comparison
purposes it is better if it is the same size for different devices. Make
it a multiple of preferred erase size that is greater than or equal to 4MiB.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
