This way all the utility functions are at the top, then the
state machine and externally callable functions are moved to
the bottom. Also clean up ieee80211_i.h a bit and add a few
comments about which functions are called from where.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove an interface, we can currently end up having
a pointer to it left in local->scan_sdata after it has been
set down, and then with a hardware scan the scan completion
can try to access it which is a bug. Alternatively, a scan
that started as a hardware scan may terminate as though it
was a software scan, if the timing is just right.
On SMP systems, software scan also has a similar problem,
just canceling the delayed work and setting a flag isn't
enough since it may be running concurrently; in this case
we would also never restore state of other interfaces.
This patch hopefully fixes the problems by always invoking
ieee80211_scan_completed or requiring it to be invoked by
the driver, I suspect the drivers that have ->hw_scan() are
buggy. The bug will not manifest itself unless you remove
the interface while hw-scanning which will also turn off
the hw, and then add a new interface which will be unusable
until you scan once.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we stop an interface, the work on it may still be pending
or running. We do cancel the timer, but we do not currently
protect against the work struct. The race is very unlikely to
hit -- it'll happen only when the driver is using mac80211's
workqueue to run long-running tasks and the sta/mesh works are
delayed for quite a bit.
This patch fixes it by cancelling the work explicitly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits off mesh handling from the STA/IBSS.
Unfortunately it increases mesh code size a bit, but I
think it makes things clearer. The patch also reduces
per-interface run-time memory usage.
Also clean up a few places where ifdef is not required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The timer restart is done wrongly, we shouldn't set the REQ_RUN
bit when the scan has finished if it hadn't been set before the
scan started. If the timer fires during the scan, it will set
REQ_RUN and then we can run the work for it, if it didn't fire
then we shouldn't run its work either.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This I shouldn't have moved to the scan implementation, move
it back to the MLME where it belongs, to the notification.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_sta_expire uses the internal __sta_info_unlink
function which can become static if this function is moved
to sta_info.c.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the new wireless regulatory infrastructure. The
main motiviation behind this was to centralize regulatory
code as each driver was implementing their own regulatory solution,
and to replace the initial centralized code we have where:
* only 3 regulatory domains are supported: US, JP and EU
* regulatory domains can only be changed through module parameter
* all rules were built statically in the kernel
We now have support for regulatory domains for many countries
and regulatory domains are now queried through a userspace agent
through udev allowing distributions to update regulatory rules
without updating the kernel.
Each driver can regulatory_hint() a regulatory domain
based on either their EEPROM mapped regulatory domain value to a
respective ISO/IEC 3166-1 country code or pass an internally built
regulatory domain. We also add support to let the user set the
regulatory domain through userspace in case of faulty EEPROMs to
further help compliance.
Support for world roaming will be added soon for cards capable of
this.
For more information see:
http://wireless.kernel.org/en/developers/Regulatory/CRDA
For now we leave an option to enable the old module parameter,
ieee80211_regdom, and to build the 3 old regdomains statically
(US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY.
These old static definitions and the module parameter is being
scheduled for removal for 2.6.29. Note that if you use this
you won't make use of a world regulatory domain as its pointless.
If you leave this option enabled and if CRDA is present and you
use US or JP we will try to ask CRDA to update us a regulatory
domain for us.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_free_keys() must be called before
ieee80211_debugfs_remove_netdev() in order to make sure that the
possible default_key symlink is removed before attempting to
remove the netdev debugfs directory.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_sta_tx function isn't MLME code any more,
it's getting used by a lot of code. Move it to utils and
rename it to ieee80211_tx_skb.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That function isn't exactly easy to read especially since it
does something in an if branch that continues after the if
because the else returns. Express it in a more readable way.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Like the HT code, this doesn't depend on the STA-mode implementation
and can be handled entirely independently. There's only stub code
for now, but when it gets filled having it in its own file will be
beneficial.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation handling isn't dependent on anything related to our
STA-mode implementation, and doesn't need to depend on it for frame
processing. This patch moves the relevant code to ht.c and adds a
hook in rx.c. For now, the relevant action frames are only processed
in STA/IBSS modes, but that's now something we can easily change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hardware is started it might be in a confused state with
respect to queue QoS parameters. This patch changes mac80211
to set sane defaults right after the hardware is brought up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleans up the code a bit and prepares for the next patch
that will use the function elsewhere.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
deauth and disassoc frames are completely identical so there's
little point in having two functions to send them rather than
one that gets a parameter. This same a bit of code size.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reorders all frame sending functions to be at the top of the
file. When reading the file, I tend to be looking at either the
frame code or the state machine, and having them mixed in the file
is confusing. When all frame sending is at the top the remainder
of the file is more readable, in my opinion.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since we refactored beaconing to not be controlled by a
fake queue this parameter to ieee80211_sta_def_wmm_params
has been unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_sta_start_scan() can very well take a non-NULL
ssid pointer with a zero ssid_len.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a scan is requested for non-STA interfaces, we simply fire
off a scan, but for STA interfaces we shouldn't because they
could be in the middle of an association. This clarifies the
corresponding code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that I've created ht.c, I can move the aggregation
code from main.c into it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the HT code in mlme.c is misplaced:
* constants/definitions belong to the ieee80211.h header
* code being used in other modes as well shouldn't be there
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves all the BSS list handling out of mlme.c to scan.c,
no further changes except fixing kzalloc/atomic_inc/atomic_inc
to kzalloc/atomic_set(2).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch refactors some code and moves the scan RX function
to scan.c. More importantly, however, it changes it so that the
MLME's beacon/probe_resp functions aren't invoked when scanning
so that we can remove a "if (scanning)" conditions from two
places.
There's a very slight behavioural change in this patch: now,
when scanning, IBSS and mesh aren't updated even on the same
channel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Here's a first patch to move some code from mlme.c to a
new file called scan.c. The end result will hopefully be
a more manageable mlme.c.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm surprised nobody complained about these before. What a waste.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now use sdata pointers most of the time, using a netdev
pointer here is somewhat artificial, use an sdata pointer instead.
Replace a netdev-prefix in a few messages by a wiphy-prefix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reorders the mlme code a bit so we don't need all the forward
function declarations. It also removes the ERP_INFO_USE_PROTECTION
define that is unused, but otherwise contains no real changes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During testing of the disassociation fixes, Tomas noticed that it
was possible to run into a situation where you'd suddenly get a
few "wlan0: dropped frame to <AP> (unauthorized port)" messages
and I found this to be due to the AP's sta_info having been
removed but netif_carrier_off not having removed/stopped traffic
yet. To avoid that, stop the queue for the interface (and avoid
bringing them up when another vif scans when they weren't up.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves disassociation code from ieee80211_set_associated
to ieee80211_set_disassoc. To reduce code duplication, it introduces
the ieee80211_sta_send_apinfo function. Additionally, it fixes a lapse
where BSS_CHANGED_HT wasn't set when notifying the driver of changes
due to disassociation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the MLME cleanly disassociate from the current BSS
when leaving it for a new one. This is not just nicer to the old AP
(we're leaving it, might as well tell it!) but also required for some
drivers that keep track of the station we're associated with, they'd
get confused because they'd think we are associated with two APs.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch restructure the flow of disassociation and deauthentication
flows to be consistent under all circumstances.
It ensures that BA session is treated down before deauthentication or disassociation,
adds the removal of the obsolete sta form station table and fixes a related bug (sta_info_destroy
without sta_info_unlink) in ieee80211_associated()
and reduce some code duplication
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since IE parsing is required for the mlme and mesh code, it's
not a static function anyway, and it's much better to have it
in util rather than the overly large mlme.c
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This says chan_switch.action_code but really means
measurement.action_code, of course the actual offset in
the frame is the same, it's just harder to understand
this way.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The action frame length checks are one too small, there's not just
an action code as the comment makes you believe, there's a category
code too, and the category code is required in each action frame
(hence part of IEEE80211_MIN_ACTION_SIZE).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we receive information about a BSS we check at some point
whether or not we think we're allowed to use the channel it is
on, but we do that fairly late. I don't think we should do it
that late, so do it earlier to avoid doing IBSS/mesh stuff on
that channel and then getting confused because it's disabled.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The conf_tx callback currently needs to be atomic, this requirement
is just because it can be called from scanning. This rearranges it
slightly to only update while not scanning (which is fine, we'll be
getting beacons when associated) and thus removes the atomic
requirement.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The if itself doesn't need to be protected, so move in the RCU
locking to avoid doing anything at all when the condition isn't
true.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch follows 11n spec naming more rigorously replacing MIMO_PS
with SM_PS (Spatial Multiplexing Power Save).
(Originally submitted as 4 patches, "mac80211: change MIMO_PS to SM_PS",
"iwlwifi: change MIMO_PS to SM_PS", "ath9k: change MIMO_PS to SM_PS",
and "iwlwifi: remove double definition of SM PS". -- JWL)
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix mac80211 kernel-doc missing struct field:
Warning(linux-2.6.27-rc1-git2//net/mac80211/sta_info.h:329): No description found for parameter 'tid_seq[IEEE80211_QOS_CTL_TID_MASK + 1]'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch address some IBSS rate issues introduced or not covered
by "mac80211: eliminate IBSS warning in rate_lowest_index()" and
"cfg80211 API for channels/bitrates, mac80211 and driver conversion".
This patch:
1. Moves addition of IBSS station from
prepare_for_handlers to ieee80211_rx_bss_info when triggered from beacon
eliminating bogus supported rates.
2. Initialize properly supported rates also in IBSS merging
3. Ensure that mandatory rates are always added into supported
rates. This is needed in case when station addition is triggered from
non beacon/probe packet. Some management frames need to be sent
4. Remove initialization of supported rates from self rates. This path
was dead code after 6bc37c06bc4 and in general incorrect.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: Vladimir Koutny <vlado@work.ksp.sk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes regression in iwlwifi IBSS rate scaling caused by patch:
commit 6bc37c06bc424bcf3f944e6a79e2d5bb537e02ed
Author: Vladimir Koutny <vlado@work.ksp.sk>
Date: Fri Jun 13 16:50:44 2008 +0200
mac80211: eliminate IBSS warning in rate_lowest_index()
An IBSS station is added in prepare_for_handlers where the rate scaling was
initialized only with single rate matching the received packet.
The correct rate scale information should be updated only in
ieee80211_rx_bss_info function where beacon is parsed. Because
of coding error the rate info was left untouched.
If a beacon has triggered the connection the rate remined 1Mbps.
This patch fixes this coding error
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: Vladimir Koutny <vlado@work.ksp.sk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously good for userspace to know up front which
interface modes a given piece of hardware might support (even
if adding such an interface might fail later because of
concurrency issues), so let's make cfg80211 aware of that.
For good measure, disallow adding interfaces in all other
modes so drivers don't forget to announce support for one mode
when they add it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 087d833e5a, which was
reported to break wireless at least in some combinations with 32bit user
space and a 64bit kernel. Alex Williamnson bisected it to this commit.
Reported-and-bisected-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: David Miller <davem@davemloft.net>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
debugfs union in struct ieee80211_sub_if_data is misused by including a
common default_key dentry as a union member. This ends occupying the same
memory area with the first dentry in other union members (structures;
usually drop_unencrypted). Consequently, debugfs operations on
default_key symlinks and drop_unencrypted entry are using the same
dentry pointer even though they are supposed to be separate ones. This
can lead to removing entries incorrectly or potentially leaving
something behind since one of the dentry pointers gets lost.
Fix this by moving the default_key dentry to a new struct
(common_debugfs) that contains dentries (more to be added in future)
that are shared by all vif types. The debugfs union must only be used
for vif type-specific entries to avoid this type of pointer corruption.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace (e.g., hostapd) to set HT capabilities for associated
STAs. This is based on a patch from Zhu Yi <yi.zhu@intel.com> (only
the NL80211_ATTR_HT_CAPABILITY for NEW_STA part is included here).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 4-5 of DSCP should not be considered by classify_d1. The
802.11 QoS Priority field is only depending on the precedence level.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up and extend scan result processing by storing all the IEs from
Beacon/Probe Response frames in a single block instead of allocating
memory for each specific IE separately. This removes lot of unnecessary
code and automatically supports reporting of new IEs (e.g., IEEE
802.11r) into user space without need to manually extend mac80211
scanning code whenever a new protocol adds IE(s).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
