commit 2372c38caadeaebc68a5ee190782c2a0df01edc3
drbd: fix for possible deadlock on IO error during resync
introduced a new ASSERT, which turns out to be wrong. Drop it.
Also serialize the state change to D_DISKLESS with the after state
change work of the -> D_FAILED transition, don't open a new race.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
As we usually update the generation UUIDs here, we should explicitly
sync them to disk. So far this has been done only implicitly by related
code paths.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This might happen if on the VERIFY_S node the disk gets dropped.
Although this is an cluster wide state transition, the VERIFY_T node,
updates it connection state first. Then the ack packet for the
cluster wide state transition travels back, and the VERIFY_S node
stops to produce the P_OV_REQUEST packets.
There is absolutely nothing wrong with that.
Further, do not log "Can not satisfy peer's..." on the VERIFY_S
node in this case, but pretend that they had equal checksum.
[Bugz 327]
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Scenario:
Something (say, flush-147:0) is in drbd_al_begin_io,
holding a local_cnt, waiting for the resync to make progress.
Disk fails, worker in after_state_ch does drbd_rs_cancel_all,
then waits for local_cnt to drop to zero.
flush-147:0 is woken by drbd_rs_cancel_all, needs to write an AL
transaction, and queues that on the worker.
Deadlock.
Fix: do not wait in the worker, have put_ldev() trigger the
state change D_FAILED -> D_DISKLESS when necessary.
put_ldev() cannot do the state change directly, as it may or may not
already hold various spinlocks. We queue a short work instead.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Various cleanup paths have been incomplete, for the very unlikely case
that we cannot allocate enough bios from process context when submitting
on behalf of the peer or resync process.
Never observed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If it was an "empty" resync, the SyncSource may have already "finished"
the resync and rotated the UUIDs, before noticing the connection loss
(and generating a new uuid, if Primary, rotating again), while the
SyncTarget did not change its uuids at all, or only got to the previous
sync-uuid.
This would then again lead to a full sync on next handshake
(see also Bug #251).
Fix:
Use explicit resync finished notification even for empty resyncs,
do not finish an empty resync implicitly on the SyncSource.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Preparation patch so more drbd_send_state() usage on the peer
will not confuse drbd in receive_state().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
no functional change, just using full state instead of just the .conn
part of it for comparisons.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd commit 17c854fea474a5eb3cfa12e4fb019e46debbc4ec
drbd: receiving of big packets, for payloads between 64kByte and 4GByte
introduced a new on-the-wire packet header format. We must no longer
assume either format, but use the result of whatever drbd_recv_header
has decoded.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We used to be16_to_cpu the length field in our received packet header.
drbd commit 17c854fea474a5eb3cfa12e4fb019e46debbc4ec
drbd: receiving of big packets, for payloads between 64kByte and 4GByte
changed this, but forgot to adjust a few places where we relied on
h->length being in native byte order.
This broke the receiving side of the RLE compressed bitmap exchange.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This caused rs_planed to be not in sync with the content of the fifo.
That in turn could cause that the resync comes to a complete halt.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Connections through a compressing proxy might have more bits
on the fly. 500MByte instead of 50MByte
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we release the page pointed to by md_io_tmpp, we need to zero out the
pointer, too, as that may be used later to decide whether we need to
allocate a new page again.
Impact: a previously freed page may be used and clobbered. Depending on
what that particular page is being used for meanwhile, this may result
in silent data corruption of completely unrelated things.
Only of concern on devices with logical_block_size != 512 byte,
if you re-attach after becoming diskless once.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Two missing corner cases to the "maximum packet size" handshake.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There are three ways to get IO suspended:
* Loss of any access to data
* Fence-peer-handler running
* User requested to suspend IO
Track those in different bits, so that one condition clearing its
state bit does not interfere with the other two conditions.
Only when the user resumes IO he overrules all three bits.
The fact is hidden from the user, he sees only a single suspend
bit.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Forgot to consider the max size for the resync requests.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a synctarget lost connection while being WFSyncUUID,
due to "state sanitizing", the attempted state change to SyncTarget
looked like an "invalidate" to after_state_ch() later,
thus caused a full sync on next handshake (Bug #318).
drbd0: PingAck did not arrive in time.
drbd0: peer( Primary -> Unknown ) conn( WFSyncUUID -> NetworkFailure ) pdsk( UpToDate -> DUnknown )
from : { cs:NetworkFailure ro:Secondary/Unknown ds:UpToDate/DUnknown r--- }
to : { cs:SyncTarget ro:Secondary/Unknown ds:Inconsistent/DUnknown r--- }
after sanizising, resulted in
state: { cs:NetworkFailure ro:Secondary/Unknown ds:Inconsistent/DUnknown r--- }
drbd0: disk( UpToDate -> Inconsistent )
Fix:
don't mask state transition errors in "sanitizing",
so the requested state change to SyncTarget fails,
instead of being implicitly "remaped" to invalidate.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we cannot satisfy a request (because our disk just broke),
we still need to drain the payload. Or we'll get a protocol error
when interpreting the payload as DRBD packet header.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
BUG trace would look like:
lc_find
drbd_rs_complete_io
got_OVResult
drbd_asender
Could be triggered by explicit, or IO-error policy based,
detach during online-verify.
We may only dereference mdev->resync, if we first get_ldev(), as the
disk may break any time, causing mdev->resync to disappear once all
ldev references have been returned.
Already in flight online-verify requests or replies may still come in,
which we then need to ignore.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Just in case we have some pending meta data changes to sync, do it
before we call our userland helper, as that may take some time,
or even cause a hard reboot.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
addendum to baa33ae4eaa4477b60af7c434c0ddd1d182c1ae7
The race:
drbd_md_sync()
if (!test_and_clear_bit(MD_DIRTY, &mdev->flags))
return;
==> RACE with drbd_md_mark_dirty() rearming the timer.
del_timer(&mdev->md_sync_timer);
Fixed by moving the del_timer before the test_and_clear_bit.
Additionally only rearm the timer in drbd_md_mark_dirty, if MD_DIRTY was
not already set, reduce the grace period from five to one second, and
add an ifdef'ed debuging aid to find code paths missing an explicit
drbd_md_sync, if any, as those are the only relevant ones for this race.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The actual race happened int the drbd_start_resync() function. Where
drbd_resync_finished() -> __drbd_set_state() set STOP_SYNC_TIMER and
armed the timer.
If the timer fired before execution reaches the mod_timer statement
at the end of drbd_start_resync() the latter would cause an
unexpected call to w_make_resync_request().
Removed the STOP_SYNC_TIMER bit, and base it on the connection state.
The STOP_SYNC_TIMER bit probably originates probably the time before
the state engine.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If pacemaker (for example) decided to initialize minor devices not in
the exact sync-after dependency order, the configuration partially
failed with an error "The sync-after minor number is invalid". (Bugz. #322)
We can avoid that by implicitly creating unconfigured minor devices,
if others depend on them.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a drbd_nl_net_conf hits the small window between the state change
to C_STANDALONE and the corresponding cleanup in after_state_ch,
that cleanup would throw away stuff we now need again,
and later trigger BUG_ON()s.
Fixed by properly serializing the new config request with
any pending cleanup.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When the complete device is marked as out of sync, we can disable
updates of the on disk AL. Currently AL updates are only disabled
if one uses the "invalidate-remote" command on an unconnected,
primary device, or when at attach time all bits in the bitmap are
set.
As of now, AL updated do not get disabled when a all bits becomes
set due to application writes to an unconnected DRBD device.
While this is a missing feature, it is not considered important,
and might get added later.
BTW, after initializing a "one legged" DRBD device
drbdadm create-md resX
drbdadm -- --force primary resX
AL updates also get disabled, until the first connect.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now we have multiple BIOs per ee, packets with a 32 bit length field,
it gets time to use these goodies.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we intent to use the block_id member of an epoch entry,
we may not use the digest member.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We now track the data rate of locally submitted resync related requests,
and can thus detect non-resync activity on the lower level device.
If the current sync rate is above c-min-rate, and the lower level device
appears to be busy, we throttle the resyncer.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
also canonicalize the return values of read_for_csum
and drbd_rs_begin_io to return -ESOMETHING, or 0 for success.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The current resync speed as displayed in /proc/drbd fluctuates a lot.
Using an array of rolling marks makes this calculation much more stable.
We used to have this (a long time ago with 0.7), but it got lost somehow.
If "stalled", do not discard the rest of the information, just add a
" (stalled)" tag to the progress line.
This patch also shortens a spinlock critical section somewhat, and
reduces the number of atomic operations in put_ldev.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The commit 288f422ec1
drbd: Track all IO requests on the TL, not writes only
moved a list_add_tail(req, ) into a region where req
may have just been freed due to conflict detection.
Fix this by adding a proper cleanup section for that code path.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We may not free tl_hash when IO is suspended, since we can not wait
until ap_bio_cnt reaches zero.
We can do this after susp reched 0, since then tl_clear was called
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
