In dm_thin_find_block() the ->fail_io flag was checked outside the
metadata device's root_lock, causing dm_thin_find_block() to race with
the setting of this flag.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use EOPNOTSUPP, rather than EINVAL, error code when user attempts to
send the pool a message. Otherwise usespace is led to believe the
message failed due to invalid argument.
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Previously REQ_DISCARD bios have been split into block sized chunks
before submission to the thin target. There are a couple of issues with
this:
- If the block size is small, a large discard request can
get broken up into a great many bios which is both slow and causes
a lot of memory pressure.
- The thin pool block size and the discard granularity for the
underlying data device need to be compatible if we want to passdown
the discard.
This patch relaxes the block size granularity for thin devices. It
makes use of the recent range locking added to the bio_prison to
quiesce a whole range of thin blocks before unmapping them. Once a
thin range has been unmapped the discard can then be passed down to
the data device for those sub ranges where the data blocks are no
longer used (ie. they weren't shared in the first place).
This patch also doesn't make any apologies about open-coding portions
of block core as a means to supporting async discard completions in the
near-term -- if/when late bio splitting lands it'll all get cleaned up.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Retrieve the next run of contiguously mapped blocks. Useful for working
out where to break up IO.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The policy tick() method is normally called from interrupt context.
Both the mq and smq policies do some bottom half work for the tick
method in their map functions. However if no IO is going through the
cache, then that bottom half work doesn't occur. With these policies
this means recently hit entries do not age and do not get written
back as early as we'd like.
Fix this by introducing a new 'can_block' parameter to the tick()
method. When this is set the bottom half work occurs immediately.
'can_block' is set when the tick method is called every second by the
core target (not in interrupt context).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If a cache metadata operation fails (e.g. transaction commit) the
cache's metadata device will abort the current transaction, set a new
needs_check flag, and the cache will transition to "read-only" mode. If
aborting the transaction or setting the needs_check flag fails the cache
will transition to "fail-io" mode.
Once needs_check is set the cache device will not be allowed to
activate. Activation requires write access to metadata. Future work is
needed to add proper support for running the cache in read-only mode.
Once in fail-io mode the cache will report a status of "Fail".
Also, add commit() wrapper that will disallow commits if in read_only or
fail mode.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When the cache is idle, writeback work was only being issued every
second. With this change outstanding writebacks are streamed
constantly. This offers a writeback performance improvement.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The stochastic-multi-queue (smq) policy addresses some of the problems
with the current multiqueue (mq) policy.
Memory usage
------------
The mq policy uses a lot of memory; 88 bytes per cache block on a 64
bit machine.
SMQ uses 28bit indexes to implement it's data structures rather than
pointers. It avoids storing an explicit hit count for each block. It
has a 'hotspot' queue rather than a pre cache which uses a quarter of
the entries (each hotspot block covers a larger area than a single
cache block).
All these mean smq uses ~25bytes per cache block. Still a lot of
memory, but a substantial improvement nontheless.
Level balancing
---------------
MQ places entries in different levels of the multiqueue structures
based on their hit count (~ln(hit count)). This means the bottom
levels generally have the most entries, and the top ones have very
few. Having unbalanced levels like this reduces the efficacy of the
multiqueue.
SMQ does not maintain a hit count, instead it swaps hit entries with
the least recently used entry from the level above. The over all
ordering being a side effect of this stochastic process. With this
scheme we can decide how many entries occupy each multiqueue level,
resulting in better promotion/demotion decisions.
Adaptability
------------
The MQ policy maintains a hit count for each cache block. For a
different block to get promoted to the cache it's hit count has to
exceed the lowest currently in the cache. This means it can take a
long time for the cache to adapt between varying IO patterns.
Periodically degrading the hit counts could help with this, but I
haven't found a nice general solution.
SMQ doesn't maintain hit counts, so a lot of this problem just goes
away. In addition it tracks performance of the hotspot queue, which
is used to decide which blocks to promote. If the hotspot queue is
performing badly then it starts moving entries more quickly between
levels. This lets it adapt to new IO patterns very quickly.
Performance
-----------
In my tests SMQ shows substantially better performance than MQ. Once
this matures a bit more I'm sure it'll become the default policy.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
With the planned cgroup writeback support, backing-dev related
declarations will be more widely used across block and cgroup;
unfortunately, including backing-dev.h from include/linux/blkdev.h
makes cyclic include dependency quite likely.
This patch separates out backing-dev-defs.h which only has the
essential definitions and updates blkdev.h to include it. c files
which need access to more backing-dev details now include
backing-dev.h directly. This takes backing-dev.h off the common
include dependency chain making it a lot easier to use it across block
and cgroup.
v2: fs/fat build failure fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, a bdi (backing_dev_info) embeds single wb (bdi_writeback)
and the role of the separation is unclear. For cgroup support for
writeback IOs, a bdi will be updated to host multiple wb's where each
wb serves writeback IOs of a different cgroup on the bdi. To achieve
that, a wb should carry all states necessary for servicing writeback
IOs for a cgroup independently.
This patch moves bdi->state into wb.
* enum bdi_state is renamed to wb_state and the prefix of all enums is
changed from BDI_ to WB_.
* Explicit zeroing of bdi->state is removed without adding zeoring of
wb->state as the whole data structure is zeroed on init anyway.
* As there's still only one bdi_writeback per backing_dev_info, all
uses of bdi->state are mechanically replaced with bdi->wb.state
introducing no behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: drbd-dev@lists.linbit.com
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
testing from Junichi Nomura and Bart Van Assche.
Also fix a casting bug in dm_merge_bvec() that could cause only a single
page to be added to a bio (Joe identified this while testing dm-cache
writeback).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVaLGPAAoJEMUj8QotnQNa1pcH/3TumkM0rvl1DK7DfWvjgfpp
+h+whWn79lOUzan/AszRvRU4Pwr7symndnJzJ/tqQ76fm8x84obvKa0jFfB9rmlM
sgw45alqB+AKcKAvocsuDIdzy2/K8FHBihccPWhe87AtJRlj57nTOJWO06gzExOp
/AJ/0Vgv3pxUCL2M4XucpQOV8eUg+gpwjDMxuMEsPVzBVYJfuRvNKoERtd9LSCSV
Y5iqdHCJiW0SWesZNrfthAAlReFzqb1c3mq55G0q0C+Z77Jf3TIPBhVfouM4NOKt
wjQoPavzyAEiKfLFy6QFCjhSOXKCI3klqO7zcyzyygVue5UTHICYRJKn7TFtbfU=
=xGAV
-----END PGP SIGNATURE-----
Merge tag 'dm-4.1-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fixes from Mike Snitzer:
"Quite a few fixes for DM's blk-mq support thanks to extra DM multipath
testing from Junichi Nomura and Bart Van Assche.
Also fix a casting bug in dm_merge_bvec() that could cause only a
single page to be added to a bio (Joe identified this while testing
dm-cache writeback)"
* tag 'dm-4.1-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix casting bug in dm_merge_bvec()
dm: fix reload failure of 0 path multipath mapping on blk-mq devices
dm: fix false warning in free_rq_clone() for unmapped requests
dm: requeue from blk-mq dm_mq_queue_rq() using BLK_MQ_RQ_QUEUE_BUSY
dm mpath: fix leak of dm_mpath_io structure in blk-mq .queue_rq error path
dm: fix NULL pointer when clone_and_map_rq returns !DM_MAPIO_REMAPPED
dm: run queue on re-queue
When considering whether to move a block to the cache we already give
preferential treatment to discarded blocks, since they are cheap to
promote (no read of the origin required since the data is junk).
The same is true of blocks that are about to be completely
overwritten, so we likewise boost their promotion chances.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Currently individual bios are deferred to the worker thread if they
cannot be processed immediately (eg, a block is in the process of
being moved to the fast device).
This patch passes whole cells across to the worker. This saves
reaquiring the cell, and also collects bios destined for the same block
together, which allows them to be mapped with a single look up to the
policy. This reduces the overhead of using dm-cache.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Rather than always releasing the prisoners in a cell, the client may
want to promote one of them to be the new holder. There is a race here
though between releasing an empty cell, and other threads adding new
inmates. So this function makes the decision with its lock held.
This function can have two outcomes:
i) An inmate is promoted to be the holder of the cell (return value of 0).
ii) The cell has no inmate for promotion and is released (return value of 1).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
We only allow non critical writeback if the origin is idle. It is up
to the policy to decide what writeback work is critical.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A little class that keeps track of the volume of io that is in flight,
and the length of time that a device has been idle for.
FIXME: rather than jiffes, may be best to use ktime_t (to support faster
devices).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There is a race between a policy deciding to replace a cache entry,
the core target writing back any dirty data from this block, and other
IO threads doing IO to the same block.
This sort of problem is avoided most of the time by the core target
grabbing a bio prison cell before making the request to the policy.
But for a demotion the core target doesn't know which block will be
demoted, so can't do this in advance.
Fix this demotion race by introducing a callback to the policy interface
that allows the policy to grab the cell on behalf of the core target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
A crypto driver can process requests synchronously or asynchronously
and can use an internal driver queue to backlog requests.
Add some comments to clarify internal logic and completion return codes.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Currently if there is a leg failure, the bio will be put into the hold
list until userspace does a remove/replace on the leg. Doing so in a
cluster config (clvmd) is problematic because there may be a temporary
path failure that results in cluster raid1 remove/replace. Such
recovery takes a long time due to a full resync.
Update dm-raid1 to optionally ignore these failures so bios continue
being issued without interrupton. To enable this feature userspace
must pass "keep_log" when creating the dm-raid1 device.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Tested-by: Liuhua Wang <lwang@suse.com>
Acked-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
On 32-bit:
drivers/md/dm-log-writes.c: In function ‘log_super’:
drivers/md/dm-log-writes.c:323: warning: integer constant is too large for ‘long’ type
Add a ULL suffix to WRITE_LOG_MAGIC to fix this.
Also add a ULL suffix to WRITE_LOG_VERSION as it's stored in a __le64
field.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add dm-raid access to the MD RAID0 personality to enable single zone
striping.
The following changes enable that access:
- add type definition to raid_types array
- make bitmap creation conditonal in super_validate(), because
bitmaps are not allowed in raid0
- set rdev->sectors to the data image size in super_validate()
to allow the raid0 personality to calculate the MD array
size properly
- use mdddev(un)lock() functions instead of direct mutex_(un)lock()
(wrapped in here because it's a trivial change)
- enhance raid_status() to always report full sync for raid0
so that userspace checks for 100% sync will succeed and allow
for resize (and takeover/reshape once added in future paches)
- enhance raid_resume() to not load bitmap in case of raid0
- add merge function to avoid data corruption (seen with readahead)
that resulted from bio payloads that grew too large. This problem
did not occur with the other raid levels because it either did not
apply without striping (raid1) or was avoided via stripe caching.
- raise version to 1.7.0 because of the raid0 API change
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- ensure maximum device limit in superblock
- rename DMPF_* (print flags) to CTR_FLAG_* (constructor flags)
and their respective struct raid_set member
- use strcasecmp() in raid10_format_to_md_layout() as in the constructor
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Remove comment above parse_raid_params() that claims
"devices_handle_discard_safely" is a table line argument when it is
actually is a module parameter.
Also, backfill dm-raid target version 1.6.0 documentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Leverage the block manager's read_only flag instead of duplicating it;
access with new dm_bm_is_read_only() method.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The overwrite has only ever about optimizing away the need to zero a
block if the entire block was being overwritten. As such it is only
relevant when zeroing is enabled.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Introduce a single common method for cleaning up a DM device's
mapped_device. No functional change, just eliminates duplication of
delicate mapped_device cleanup code.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
More often than not a request that is requeued _is_ mapped (meaning the
clone request is allocated and clone->q is initialized). Rename
dm_requeue_unmapped_original_request() to avoid potential confusion due
to function name containing "unmapped".
Also, remove dm_requeue_unmapped_request() since callers can easily call
the dm_requeue_original_request() directly.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Do not allocate the io_pool mempool for blk-mq request-based DM
(DM_TYPE_MQ_REQUEST_BASED) in dm_alloc_rq_mempools().
Also refine __bind_mempools() to have more precise awareness of which
mempools each type of DM device uses -- avoids mempool churn when
reloading DM tables (particularly for DM_TYPE_REQUEST_BASED).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm_merge_bvec() was originally added in f6fccb ("dm: introduce
merge_bvec_fn"). In that commit a value in sectors is converted to
bytes using << 9, and then assigned to an int. This code made
assumptions about the value of BIO_MAX_SECTORS.
A later commit 148e51 ("dm: improve documentation and code clarity in
dm_merge_bvec") was meant to have no functional change but it removed
the use of BIO_MAX_SECTORS in favor of using queue_max_sectors(). At
this point the cast from sector_t to int resulted in a zero value. The
fallout being dm_merge_bvec() would only allow a single page to be added
to a bio.
This interim fix is minimal for the benefit of stable@ because the more
comprehensive cleanup of passing a sector_t to all DM targets' merge
function will impact quite a few DM targets.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.19+
dm-multipath accepts 0 path mapping.
# echo '0 2097152 multipath 0 0 0 0' | dmsetup create newdev
Such a mapping can be used to release underlying devices while still
holding requests in its queue until working paths come back.
However, once the multipath device is created over blk-mq devices,
it rejects reloading of 0 path mapping:
# echo '0 2097152 multipath 0 0 1 1 queue-length 0 1 1 /dev/sda 1' \
| dmsetup create mpath1
# echo '0 2097152 multipath 0 0 0 0' | dmsetup load mpath1
device-mapper: reload ioctl on mpath1 failed: Invalid argument
Command failed
With following kernel message:
device-mapper: ioctl: can't change device type after initial table load.
DM tries to inherit the current table type using dm_table_set_type()
but it doesn't work as expected because of unnecessary check about
whether the target type is hybrid or not.
Hybrid type is for targets that work as either request-based or bio-based
and not required for blk-mq or non blk-mq checking.
Fixes: 65803c205983 ("dm table: train hybrid target type detection to select blk-mq if appropriate")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Unfortunately this functionality was merged a little prematurely.
The necessary testing and code review is now complete (or as
complete as it can be) and to code passes a variety of tests
and looks quite sensible.
Also a fix for some recent locking changes - a race was introduced
which causes a reshape request to sometimes fail. No data safety issues.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Y0Vm
-----END PGP SIGNATURE-----
Merge tag 'md/4.1-rc5-fixes' of git://neil.brown.name/md
Pull m,ore md bugfixes gfrom Neil Brown:
"Assorted fixes for new RAID5 stripe-batching functionality.
Unfortunately this functionality was merged a little prematurely. The
necessary testing and code review is now complete (or as complete as
it can be) and to code passes a variety of tests and looks quite
sensible.
Also a fix for some recent locking changes - a race was introduced
which causes a reshape request to sometimes fail. No data safety
issues"
* tag 'md/4.1-rc5-fixes' of git://neil.brown.name/md:
md: fix race when unfreezing sync_action
md/raid5: break stripe-batches when the array has failed.
md/raid5: call break_stripe_batch_list from handle_stripe_clean_event
md/raid5: be more selective about distributing flags across batch.
md/raid5: add handle_flags arg to break_stripe_batch_list.
md/raid5: duplicate some more handle_stripe_clean_event code in break_stripe_batch_list
md/raid5: remove condition test from check_break_stripe_batch_list.
md/raid5: Ensure a batch member is not handled prematurely.
md/raid5: close race between STRIPE_BIT_DELAY and batching.
md/raid5: ensure whole batch is delayed for all required bitmap updates.
When stacking request-based dm device on non blk-mq device and
device-mapper target could not map the request (error target is used,
multipath target with all paths down, etc), the WARN_ON_ONCE() in
free_rq_clone() will trigger when it shouldn't.
The warning was added by commit aa6df8d ("dm: fix free_rq_clone() NULL
pointer when requeueing unmapped request"). But free_rq_clone() with
clone->q == NULL is valid usage for the case where
dm_kill_unmapped_request() initiates request cleanup.
Fix this false warning by just removing the WARN_ON -- it only generated
false positives and was never useful in catching the intended case
(completing clone request not being mapped e.g. clone->q being NULL).
Fixes: aa6df8d ("dm: fix free_rq_clone() NULL pointer when requeueing unmapped request")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A recent change removed the need for locking around writing
to "sync_action" (and various other places), but introduced a
subtle race.
When e.g. setting 'reshape' on a 'frozen' array, the 'frozen'
flag is cleared before 'reshape' is set, so the md thread can
get in and start trying recovery - which isn't wanted.
So instead of clearing MD_RECOVERY_FROZEN for any command
except 'frozen', only clear it when each specific command
is parsed. This allows the handling of 'reshape' to clear
the bit while a lock is held.
Also remove some places where we set MD_RECOVERY_NEEDED,
as it is always set on non-error exit of the function.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 6791875e2e53 ("md: make reconfig_mutex optional for writes to md sysfs files.")
Now that the code in break_stripe_batch_list() is nearly identical
to the end of handle_stripe_clean_event, replace the later
with a function call.
The only remaining difference of any interest is the masking that is
applieds to dev[i].flags copied from head_sh.
R5_WriteError certainly isn't wanted as it is set per-stripe, not
per-patch. R5_Overlap isn't wanted as it is explicitly handled.
Signed-off-by: NeilBrown <neilb@suse.de>
When a batch of stripes is broken up, we keep some of the flags
that were per-stripe, and copy other flags from the head to all
others.
This only happens while a stripe is being handled, so many of the
flags are irrelevant.
The "SYNC_FLAGS" (which I've renamed to make it clear there are
several) and STRIPE_DEGRADED are set per-stripe and so need to be
preserved. STRIPE_INSYNC is the only flag that is set on the head
that needs to be propagated to all others.
For safety, add a WARN_ON if others are set, except:
STRIPE_HANDLE - this is safe and per-stripe and we are going to set
in several cases anyway
STRIPE_INSYNC
STRIPE_IO_STARTED - this is just a hint and doesn't hurt.
STRIPE_ON_PLUG_LIST
STRIPE_ON_RELEASE_LIST - It is a point pointless for a batched
stripe to be on one of these lists, but it can happen
as can be safely ignored.
Signed-off-by: NeilBrown <neilb@suse.de>
When we break a stripe_batch_list we sometimes want to set
STRIPE_HANDLE on the individual stripes, and sometimes not.
So pass a 'handle_flags' arg. If it is zero, always set STRIPE_HANDLE
(on non-head stripes). If not zero, only set it if any of the given
flags are present.
Signed-off-by: NeilBrown <neilb@suse.de>
break_stripe_batch list didn't clear head_sh->batch_head.
This was probably a bug.
Also clear all R5_Overlap flags and if any were cleared, wake up
'wait_for_overlap'.
This isn't always necessary but the worst effect is a little
extra checking for code that is waiting on wait_for_overlap.
Also, don't use wake_up_nr() because that does the wrong thing
if 'nr' is zero, and it number of flags cleared doesn't
strongly correlate with the number of threads to wake.
Signed-off-by: NeilBrown <neilb@suse.de>
handle_stripe_clean_event() contains a chunk of code very
similar to check_break_stripe_batch_list().
If we make the latter more like the former, we can end up
with just one copy of this code.
This first step removed the condition (and the 'check_') part
of the name. This has the added advantage of making it clear
what check is being performed at the point where the function is
called.
Signed-off-by: NeilBrown <neilb@suse.de>
If a stripe is a member of a batch, but not the head, it must
not be handled separately from the rest of the batch.
'clear_batch_ready()' handles this requirement to some
extent but not completely. If a member is passed to handle_stripe()
a second time it returns '0' indicating the stripe can be handled,
which is wrong.
So add an extra test.
Signed-off-by: NeilBrown <neilb@suse.de>
When we add a write to a stripe we need to make sure the bitmap
bit is set. While doing that the stripe is not locked so it could
be added to a batch after which further changes to STRIPE_BIT_DELAY
and ->bm_seq are ineffective.
So we need to hold off adding to a stripe until bitmap_startwrite has
completed at least once, and we need to avoid further changes to
STRIPE_BIT_DELAY once the stripe has been added to a batch.
If a bitmap_startwrite() completes after the stripe was added to a
batch, it will not have set the bit, only incremented a counter, so no
extra delay of the stripe is needed.
Reported-by: Shaohua Li <shli@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
