This patch correctly releases the firmware if the magic string in the
firmware header does not match.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch correctly releases the firmware if the magic string in the
firmware header does not match.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Place a cap on the number of channels clocks are generated for. This is
intended for use with systems which have the WM5102 master an I2S bus with
multiple data lines.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some systems may wish to support switching between telephony and CD audio
clock rates but this is restricted by enforcement of constraints on the
current DAI clock. Support setting clocks to zero and don't enforce any
constraints in that case in order to facilitate this use case.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix up all callers as they were before, with make one change: an
unsigned module taints the kernel, but doesn't turn off lockdep.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Normally kmalloc() returns things that are DMA safe so not visible on all
platforms but we do need to explicitly request DMA safe memory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Normally kmalloc() returns things that are DMA safe so not visible on all
platforms but we do need to explicitly request DMA safe memory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sets the ADSP1 clock rate to match the system clock
rate. To support this the codec driver provides
details of register containing the system clock
control bits.
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement support for a new revision of the coefficeint file format for
ADSP cores.
Since coefficient file format 0 has not been widely deployed and is very
unlikely to ever be used with this driver code support for it has been
removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds a very simple machine driver using the Wolfson wm9712 AC97
codec.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise we'll get the wrong LRCLK if we need to pick a higher BCLK than
is required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
__devinitconst and friends have recently been removed and must not be
used anymore.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We only log the result and since the interrupt triggers on loss of lock
during shutdown this may lead to spurious interrupts during shutdown
delaying the process.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is always true now and the __dev* macros have been removed.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Support for loading the Renesas FSI driver via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds the driver for the Tegra 2x AC97 host controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current simple-card driver calls asoc_simple_card_dai_init()
if platform had a asoc_simple_card_dai_init pointer.
And, this initialization function works only
when platform has an applicable initial value for each dai settings.
And basically, almost all sound card requires certain initialization.
This means that almost all platform has initialization settings,
and driver do nothing if it doesn't have settings.
And additionally, current simple-card supports sysclk settings but it was
only for codec. In order to abolish deviation between cpu and codec,
and in order to simplify processing,
this patch adds asoc_simple_dai, and removed pointless
struct asoc_simple_dai_init_info which was trigger of
calling asoc_simple_card_dai_init().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With idle_bias_off these are no longer needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are many firmwares available for ADSP devices. Add basic support
for selecting between them, including a couple of feature sets in the
set of available firmware to start off with.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The generated defines in the header are pre-shifted.
Reported-by: Heather Lomond <Heather.Lomond@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enable bypass when the regulator is idle, not when it is in use. This is
consistent with what the few existing users actually want.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I've removed several unreachable returns.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With commit f2818d0 (ASoC: fsl: fix miscompilation of snd-soc-imx-pcm),
we will see the following build error when building modules with
CONFIG_SND_IMX_SOC=m in imx_v6_v7_defconfig.
CC [M] sound/soc/fsl/phycore-ac97.o
LD [M] sound/soc/fsl/snd-soc-fsl-ssi.o
LD [M] sound/soc/fsl/snd-soc-fsl-utils.o
LD [M] sound/soc/fsl/snd-soc-imx-ssi.o
LD [M] sound/soc/fsl/snd-soc-imx-audmux.o
LD [M] sound/soc/fsl/snd-soc-imx-pcm.o
sound/soc/fsl/imx-pcm-dma.o: In function `init_module':
imx-pcm-dma.c:(.init.text+0x0): multiple definition of `init_module'
sound/soc/fsl/imx-pcm-fiq.o:imx-pcm-fiq.c:(.init.text+0x0): first defined here
sound/soc/fsl/imx-pcm-dma.o: In function `cleanup_module':
imx-pcm-dma.c:(.exit.text+0x0): multiple definition of `cleanup_module'
sound/soc/fsl/imx-pcm-fiq.o:imx-pcm-fiq.c:(.exit.text+0x0): first defined here
make[4]: *** [sound/soc/fsl/snd-soc-imx-pcm.o] Error 1
Instead of using bool for SND_SOC_IMX_PCM_FIQ and SND_SOC_IMX_PCM_DMA
to fix the original issue, we should completely remove SND_SOC_IMX_PCM
and have imx-pcm.o statically linked with imx-pcm-fiq.o or imx-pcm-dma.o.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As the IEC-60958 channel status word is set by ANDing and ORing with
the appropriate definitions, the word bytes need to be initialized
to zero to avoid misconfiguration due to previous hw_params calls.
Signed-off-by: Ricardo Neri <rneri@dextratech.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The code to do the ramp has been removed a long time ago. Remove the
remaining code as well since this is not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's no need to create a queue for this anymore
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In this way we can clean up the probe and remove paths
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No need to set the bias_level twice to _STANDBY - since this is the only
state the device could be at suspend time. The driver do not support
idle_bias_off yet.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With idle_bias_off these are no longer needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
