* acpi-lpss:
ACPI / LPSS: not using UART RTS override with Auto Flow Control
ACPI / LPSS: remove struct lpss_shared_clock
ACPI / LPSS: support for 133MHz I2C source clock on Baytrail
ACPI / LPSS: drop clkdev_name member from lpss_device_desc
ACPI / LPSS: introduce flags
* acpi-apple:
ACPI / SBS: Fix check in acpi_ac_get_present()
ACPI: Support _OSI("Darwin") correctly
ACPI / SBS: Disable smart battery manager on Apple
ACPI / SBS: Don't assume the existence of an SBS charger
Add a routine for host OSes to enable all wakeup GPEs and disable
all of the non-wakeup ones at the same time.
It will be used for the handling of GPE wakeup from suspend-to-idle
in Linux.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since acpi_hw_enable_wakeup_gpe_block() is currently always called
after disabling all GPEs, it can actually write zeros to all
non-wakeup enable bits unconditionally.
That will be useful going forward for disabling runtime GPEs and
enabling wakeup GPEs in one go instead of doing that in two steps
(disable runtime and enable wakeup) which in theory may lead to a
loss of a wakeup event.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The _DOD method lists which video output device is currently attached so
we should only care about them and ignore others. An user recently
reported that there are two acpi_video interfaces appeared on his system
and one of them doesn't work. From the acpidump, it is found that there
are more than one video output devices that have _BCM control method but
the _DOD lists only one of them. So this patch checks if the video output
device is in the _DOD list and will not create backlight device if it is
not in the list. Also, we consider the broken _DOD case(reflected by the
video->attached_count is 0) and do not change behaviour for those broken
_DOD systems.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84111
Reported-and-tested-by: ntrrgc@gmail.com
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Parentheses are missing under an if () statement in
acpi_ac_get_present() which makes the check work differently
from what was intended (at least according to the comment right
above it). Add the missing parens.
The problem was found by sparse.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Apple hardware queries _OSI("Darwin") in order to determine whether the
system is running OS X, and changes firmware behaviour based on the
answer. The most obvious difference in behaviour is that Thunderbolt
hardware is forcibly powered down unless the system is running OS X. The
obvious solution would be to simply add Darwin to the list of supported
_OSI strings, but this causes problems.
Recent Apple hardware includes two separate methods for checking _OSI
strings. The first will check whether Darwin is supported, and if so
will exit. The second will check whether Darwin is supported, but will
then continue to check for further operating systems. If a further
operating system is found then later firmware code will assume that the
OS is not OS X. This results in the unfortunate situation where the
Thunderbolt controller is available at boot time but remains powered
down after suspend.
The easiest way to handle this is to special-case it in the
Linux-specific OSI handling code. If we see Darwin, we should answer
true and then disable all other _OSI vendor strings.
The next problem is that the Apple PCI _OSC method has the following
code:
if (LEqual (0x01, OSDW ()))
if (LAnd (LEqual (Arg0, GUID), NEXP)
(do stuff)
else
(fail)
NEXP is a value in high memory and is presumably under the control of
the firmware. No methods sets it. The methods that are called in the "do
stuff" path are dummies. Unless there's some additional firmware call in
early boot, there's no way for this call to succeed - and even if it
does, it doesn't do anything.
The easiest way to handle this is simply to ignore it. We know which
flags would be set, so just set them by hand if the platform is running
in Darwin mode.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
[andreas.noever@gmail.com: merged two patches, do not touch ACPICA]
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Touching the smart battery manager at all on Apple hardware appears to
make it unhappy - unplugging the AC adapter triggers accesses that hang
the controller for several minutes. Quirk it out via DMI in order to
avoid this. Compensate by changing battery presence if we fail to
communicate with the battery.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Apple hardware continues to expose an ACPI AC charger even when using
SBS to report battery state. The charger status byte returns all 0s in
this case. Since the spec requires that bit 4 be 1 at all times, assume
that there's not really a charger if it's set to zero.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lenovo Ideapad 570 is a pre-win8 laptop where not using vendor
backlight causes the backlight controls not to work.
Signed-off-by: Stepan Bujnak <stepanbujnak@fastmail.fm>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adding a check for UART Auto Flow Control feature and only
enabling the RTS override when it's not supported. RTS
override is not needed when Auto Flow Control is used and
they shouldn't be used together.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Changes to correct several GPIO issues:
1) The update_rule in a GPIO field definition is now ignored;
a read-modify-write operation is never performed for GPIO fields.
(Internally, this means that the field assembly/disassembly
code is completely bypassed for GPIO.)
2) The Address parameter passed to a GPIO region handler is
now the bit offset of the field from a previous Connection()
operator. Thus, it becomes a "Pin Number Index" into the
Connection() resource descriptor.
3) The bit_width parameter passed to a GPIO region handler is
now the exact bit width of the GPIO field. Thus, it can be
interpreted as "number of pins".
Overall, we can now say that the region handler interface
to GPIO handlers is a raw "bit/pin" addressed interface, not
a byte-addressed interface like the system_memory handler interface.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some systems (Asus T100 in particular) there are strict ordering
dependencies between LPSS devices with respect to power management
that break if they suspend/resume asynchronously.
In theory it should be possible to follow those dependencies in the
async suspend/resume case too (the ACPI tables tell as that the
dependencies are there), but since we're missing infrastructure
for that at the moment, disable async suspend/resume for all of
the LPSS devices for the time being.
Link: http://marc.info/?l=linux-acpi&m=141158962321905&w=2
Fixes: 8ce62f85a81f (ACPI / platform / LPSS: Enable async suspend/resume of LPSS devices)
Signed-off-by: Li Aubrey <aubrey.li@linux.intel.com>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a typo, it should be negative -errno instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ThinkPad X201s has a working ACPI video backlight interface and is
shipped before Win8; then there is BIOS update that starts to query
_OSI("Windows 2012") and that would make our video module stop creating
backlight interface and caused problem for the user. Add it to the DMI
table to disable native backlight to fix this problem.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81691
Link: https://bugzilla.kernel.org/show_bug.cgi?id=51231
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Reported-and-tested-by: Yves-Alexis Perez <corsac@debian.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 46394fd01 (ACPI / hotplug: Move container-specific code out of
the core) removed the generation of "online" uevents for containers,
because "add" uevents are now generated for them automatically when
container system devices are registered. However, there are user
space tools that need to be notified when the container and all of
its children have been enumerated, which doesn't happen any more.
For this reason, add a mechanism allowing "online" uevents to be
generated for ACPI containers after enumerating the container along
with all of its children.
Fixes: 46394fd01 (ACPI / hotplug: Move container-specific code out of the core)
Reported-and-tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Enumeration
- Don't default exclusively to first video device (Bruno Prémont)
PCI device hotplug
- Remove "no hotplug settings from platform" warning (Bjorn Helgaas)
- Add pci_ignore_hotplug() for VGA switcheroo (Bjorn Helgaas)
Freescale i.MX6
- Put LTSSM in "Detect" state before disabling (Lucas Stach)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xIYe
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These fix:
- Boot video device detection on dual-GPU Apple systems
- Hotplug fiascos on VGA switcheroo with radeon & nouveau drivers
- Boot hang on Freescale i.MX6 systems
- Excessive "no hotplug settings from platform" warnings
In particular:
Enumeration
- Don't default exclusively to first video device (Bruno Prémont)
PCI device hotplug
- Remove "no hotplug settings from platform" warning (Bjorn Helgaas)
- Add pci_ignore_hotplug() for VGA switcheroo (Bjorn Helgaas)
Freescale i.MX6
- Put LTSSM in "Detect" state before disabling (Lucas Stach)"
* tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
vgaarb: Drop obsolete #ifndef
vgaarb: Don't default exclusively to first video device with mem+io
ACPIPHP / radeon / nouveau: Remove acpi_bus_no_hotplug()
PCI: Remove "no hotplug settings from platform" warning
PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device
PCI: imx6: Put LTSSM in "Detect" state before disabling it
MAINTAINERS: Add Lucas Stach as co-maintainer for i.MX6 PCI driver
Revert parts of f244d8b623da ("ACPIPHP / radeon / nouveau: Fix VGA
switcheroo problem related to hotplug").
A previous commit 5493b31f0b55 ("PCI: Add pci_ignore_hotplug() to ignore
hotplug events for a device") added equivalent functionality implemented in
a different way for both acpiphp and pciehp.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Rajat Jain <rajatxjain@gmail.com>
PM entries of LPSS power domain were not implemented correctly
in commit c78b0830667a "ACPI / LPSS: custom power domain for LPSS".
This patch fixes and completes these PM entries.
Fixes: c78b0830667a (ACPI / LPSS: custom power domain for LPSS)
Signed-off-by: Li Aubrey <aubrey.li@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 232de5143790 ("ACPI / battery: fix wrong value of
capacity_now reported when fully charged")
There is nothing wrong or unexpected about 'capacity_now' increasing above
the last 'full_charge_capacity' value. Different charging cycles will cause
'full_charge_capacity' to vary, both up and down. Good battery firmwares
will update 'full_charge_capacity' when the current charging cycle is
complete, increasing it if necessary. It might even go above
'design_capacity' on a fresh and healthy battery.
Capping 'capacity_now' to 'full_charge_capacity' is plain wrong, and
printing a warning if this doesn't happen to match the 'design_capacity'
is both annoying and terribly wrong.
This results in bogus warnings on perfectly working systems/firmwares:
[Firmware Bug]: battery: reported current charge level (39800) is higher than reported maximum charge level (39800).
and wrong values being reported for 'capacity_now' and
'full_charge_capacity' after the warning has been triggered.
Fixes: 232de5143790 ("ACPI / battery: fix wrong value of capacity_now reported when fully charged")
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit d719870b41e0 ("ACPI / battery: Fix warning message in
acpi_battery_get_state()")
Capping 'capacity_now' to 'full_charge_capacity' is plain wrong. If this
is necessary to work around some buggy firmware, then the workaround needs
protection against being applied to working firmwares.
Good battery firmwares will allow 'capacity_now' to increase above
'full_charge_capacity', and will update the latter when the battery
is fully charged. By capping 'capacity_now' we lose accurate capacity
reporting until charging is complete whenever 'full_charge_capacity'
needs to be increased.
Fixes: d719870b41e0 ("ACPI / battery: Fix warning message in acpi_battery_get_state()")
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The value64 parameter is an u64 point that used to transfer the value
for write to CMOS, or used to return the value that's read from CMOS.
The value64 is an u64 point, so don't need get address again. It causes
acpi_cmos_rtc_space_handler always return 0 to reader and didn't write
expected value to CMOS.
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Cc: 3.11+ <stable@vger.kernel.org> # 3.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpica:
ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.
* acpi-processor:
ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
* acpi-scan:
ACPI / scan: not cache _SUN value in struct acpi_device_pnp
There is a following AB-BA dependency between cpu_hotplug.lock and
cpuidle_lock:
1) cpu_hotplug.lock -> cpuidle_lock
enable_nonboot_cpus()
_cpu_up()
cpu_hotplug_begin()
LOCK(cpu_hotplug.lock)
cpu_notify()
...
acpi_processor_hotplug()
cpuidle_pause_and_lock()
LOCK(cpuidle_lock)
2) cpuidle_lock -> cpu_hotplug.lock
acpi_os_execute_deferred() workqueue
...
acpi_processor_cst_has_changed()
cpuidle_pause_and_lock()
LOCK(cpuidle_lock)
get_online_cpus()
LOCK(cpu_hotplug.lock)
Fix this by reversing the order acpi_processor_cst_has_changed() does
thigs -- let it first execute the protection against CPU hotplug by
calling get_online_cpus() and obtain the cpuidle lock only after that (and
perform the symmentric change when allowing CPUs hotplug again and
dropping cpuidle lock).
Spotted by lockdep.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
use_native_backlight_dmi defaults to true now, so
video_set_use_native_backlight is a nop. Drop it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The _SUN device indentification object is not guaranteed to return
the same value every time it is executed, so we should not cache its
return value, but rather execute it every time as needed. If it is
cached, an incorrect stale value may be used in some situations.
This issue was exposed by commit 202317a573b2 (ACPI / scan: Add
acpi_device objects for all device nodes in the namespace). Fix it
by avoiding to cache the return value of _SUN.
Fixes: 202317a573b2 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The field is actually 2 bits, not 1.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Nothing requires it anymore. The PWM driver no longer
uses clk framework to get the rate.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The I2C controllers on Baytrail can get the clock from
100MHz or 133MHz source clock. The first bits in the private
clock parameter register indicates which one is being used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It was used to provide the correct con_id for the dma
driver, but it's not needed. Even if the driver requests a
clock with the con_id, it still gets the correct clock. The
device name is enough to match a single clock.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace the booleans with a single flags member variable.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Clevo W350etq's EC will not produce GPE interrupt some time after
booting. The ACPI notify event won't trigger when the issue takes
place. After debugging, adding msi quirk for the machine can fix
the issue. This patch is to add msi quirk for the machine.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431
Reported-and-tested-by: qbanin@gmail.com
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://bugs.freedesktop.org/show_bug.cgi?id=81515
Reported-and-tested-by: Hohahiu <rakothedin@gmail.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some laptops have a working acpi_video backlight control, and using native
backlight on these causes a regression where backlight control does not work
when userspace is not handling brightness key events. Disable native_backlight
on these to fix this.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81691
Reported-and-tested-by: Andre Müller <andre.muller@web.de>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 751109aad583 ("ACPI / video: Change the default for
video.use_native_backlight to 1") has changed the default for
use_native_backlight from 0 to 1, but instead of changing
use_native_backlight_dmi to true, and leaving use_native_backlight_param at -1,
it has changed use_native_backlight_param to 1.
This causes acpi_video_use_native_backlight() to always think that a value was
specified through the param, making it impossible to add a dmi based quirk
to force 0 now that the default is 1.
This fixes this by restoring the use_native_backlight_param default to -1, and
instead setting the use_native_backlight_dmi default to true.
Fixes: 751109aad583 (ACPI / video: Change the default for video.use_native_backlight to 1)
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds ACPICA kernel runtime support to validate contents/format
of the _DSD package, similar to the iASL support. Ported by
Mika Westerberg.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull x86 fixes from Peter Anvin:
"One patch to avoid assigning interrupts we don't actually have on
non-PC platforms, and two patches that addresses bugs in the new
IOAPIC assignment code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, irq, PCI: Keep IRQ assignment for runtime power management
x86: irq: Fix bug in setting IOAPIC pin attributes
x86: Fix non-PC platform kernel crash on boot due to NULL dereference
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during runtime power
management, otherwise it may cause failure of device wakeups.
Commit 3eec595235c17a7 "x86, irq, PCI: Keep IRQ assignment for PCI
devices during suspend/hibernation" has fixed the issue for suspend/
hibernation, we also need the same fix for runtime device sleep too.
Fix: https://bugzilla.kernel.org/show_bug.cgi?id=83271
Reported-and-Tested-by: EmanueL Czirai <amanual@openmailbox.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: EmanueL Czirai <amanual@openmailbox.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1409304383-18806-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* acpi-scan:
ACPI: Run fixed event device notifications in process context
ACPI / scan: Allow ACPI drivers to bind to PNP device objects
* acpi-ec:
ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC
ACPI / EC: Add support to disallow QR_EC to be issued when SCI_EVT isn't set
* acpi-lpss:
ACPI / LPSS: Add ACPI IDs for Intel Braswell
Enable more identifiers for the existing devices for Intel Braswell and
Cherryview.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is platform refusing to respond QR_EC when SCI_EVT isn't set
which is Acer Aspire V5-573G.
By disallowing QR_EC to be issued before the previous one has been
completed we are able to reduce the possibilities to trigger issues on
such platforms.
Note that this fix can only reduce the occurrence rate of this issue, but
this issue may still occur when such a platform doesn't clear SCI_EVT
before or immediately after completing the previous QR_EC transaction.
This patch cannot fix the CLEAR_ON_RESUME quirk which also relies on
the assumption that the platforms are able to respond even when SCI_EVT
isn't set.
But this patch is still useful as it can help to reduce the number of
scheduled QR_EC work items.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=82611
Reported-and-tested-by: Alexander Mezin <mezin.alexander@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a platform refusing to respond QR_EC when SCI_EVT isn't set
(Acer Aspire V5-573G).
Currently, we rely on the behaviour that the EC firmware can respond
something (for example, 0x00 to indicate "no outstanding events") to
QR_EC even when SCI_EVT is not set, but the reporter has complained
about AC/battery pluging/unpluging and video brightness change delay
on that platform.
This is because the work item that has issued QR_EC has to wait until
timeout in this case, and the _Qxx method evaluation work item queued
after QR_EC one is delayed.
It sounds reasonable to fix this issue by:
1. Implementing SCI_EVT sanity check before issuing QR_EC in the EC
driver's main state machine.
2. Moving QR_EC issuing out of the work queue used by _Qxx evaluation
to a seperate IRQ handling thread.
This patch fixes this issue using solution 1.
By disallowing QR_EC to be issued when SCI_EVT isn't set, we are able to
handle such platform in the EC driver's main state machine. This patch
enhances the state machine in this way to survive with such malfunctioning
EC firmware.
Note that this patch can also fix CLEAR_ON_RESUME quirk which also relies
on the assumption that the platforms are able to respond even when SCI_EVT
isn't set.
Fixes: c0d653412fc8 ACPI / EC: Fix race condition in ec_transaction_completed()
Link: https://bugzilla.kernel.org/show_bug.cgi?id=82611
Reported-and-tested-by: Alexander Mezin <mezin.alexander@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
