When I added 3448a19da4
I forgot about the special uv handling code for this, so this
patch fixes it up.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ingo Molnar
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds support for a new version of the SGI UV hub
chip. The hub chip is the node controller that connects multiple
blades into a larger coherent SSI.
For the most part, UV2 is compatible with UV1. The majority of
the changes are in the addresses of MMRs and in a few cases, the
contents of MMRs. These changes are the result in changes in the
system topology such as node configuration, processor types,
maximum nodes, physical address sizes, etc.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20110511175028.GA18006@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This will pave the way for each apic driver to be self-contained
and eliminate the need for apic_probe[].
Order in which apic drivers are listed in the .apicdrivers
section is important, as this determines the apic probe order.
And this is enforced by the ordering of apic driver files in the
Makefile and the macros apic_driver()/apic_drivers().
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: steiner@sgi.com
Cc: gorcunov@openvz.org
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110521005526.068775085@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use the unused probe routine in the apic driver to finalize the
apic model selection. This cleans up the
default_setup_apic_routing() and this probe routine in future
can also be used for doing any apic model specific
initialisation.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: steiner@sgi.com
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110519234637.247458931@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes problems seen on UV systems handling NMIs from the
node controller.
I isolated the "dazed..." messages that I saw earlier to a bug in
the BMC on our platform. It was sending NMIs w/o properly setting
a register that indicated the source of NMI.
So rather than _assuming_ any unhandled NMI came from the UV system
maintenance console (SMC), add a check to verify that the SMC actually
sent the NMI.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: gorcunov@gmail.com
Cc: dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After a crash dump on an SGI Altix UV system the crash kernel
fails to cause a reboot. EFI mode is disabled in the kdump
kernel, so only the reboot_type of BOOT_ACPI works.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: rja@sgi.com
LKML-Reference: <E1Q5Iuo-00013b-UK@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Stop including <linux/delay.h> in x86 header files which don't
need it. This will let the compiler complain when this header is
not included by source files when it should, so that
contributors can fix the problem before building on other
architectures starts to fail.
Credits go to Geert for the idea.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20110325152014.297890ec@endymion.delvare>
[ this also fixes an upstream build bug in drivers/media/rc/ite-cir.c ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
apic->apicid_to_node() is 32bit specific apic operation which
determines NUMA node for a CPU. Depending on the APIC
implementation, it can be easier to determine NUMA node from
either physical or logical apicid. Currently,
->apicid_to_node() takes @logical_apicid and calls
hard_smp_processor_id() if the physical apicid is needed.
This prevents NUMA mapping from being queried from a different
CPU, which in turn makes it impossible to initialize NUMA
mapping before SMP bringup.
This patch replaces apic->apicid_to_node() with
->x86_32_numa_cpu_node() which takes @cpu, from which both
logical and physical apicids can easily be determined. While at
it, drop duplicate implementations from bigsmp_32 and summit_32,
and use the default one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Cc: eric.dumazet@gmail.com
Cc: yinghai@kernel.org
Cc: brgerst@gmail.com
Cc: gorcunov@gmail.com
Cc: shaohui.zheng@intel.com
Cc: rientjes@google.com
LKML-Reference: <1295789862-25482-13-git-send-email-tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After the previous patch, apic->cpu_to_logical_apicid() is no
longer used. Kill it.
For apic types with custom cpu_to_logical_apicid() which is also
used for other purposes, remove the function and modify its
users to do the mapping directly.
#ifdef's on CONFIG_SMP in es7000_32 and summit_32 are ignored
during conversion as they are not used for UP kernels.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: eric.dumazet@gmail.com
Cc: yinghai@kernel.org
Cc: brgerst@gmail.com
Cc: gorcunov@gmail.com
Cc: penberg@kernel.org
Cc: shaohui.zheng@intel.com
Cc: rientjes@google.com
LKML-Reference: <1295789862-25482-7-git-send-email-tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix Moorestown VRTC fixmap placement
x86/gpio: Implement x86 gpio_to_irq convert function
x86, UV: Fix APICID shift for Westmere processors
x86: Use PCI method for enabling AMD extended config space before MSR method
x86: tsc: Prevent delayed init if initial tsc calibration failed
x86, lapic-timer: Increase the max_delta to 31 bits
x86: Fix sparse non-ANSI function warnings in smpboot.c
x86, numa: Fix CONFIG_DEBUG_PER_CPU_MAPS without NUMA emulation
x86, AMD, PCI: Add AMD northbridge PCI device id for CPU families 12h and 14h
x86, numa: Fix cpu to node mapping for sparse node ids
x86, numa: Fake node-to-cpumask for NUMA emulation
x86, numa: Fake apicid and pxm mappings for NUMA emulation
x86, numa: Avoid compiling NUMA emulation functions without CONFIG_NUMA_EMU
x86, numa: Reduce minimum fake node size to 32M
Fix up trivial conflict in arch/x86/kernel/apic/x2apic_uv_x.c
Westmere processors use a different algorithm for
assigning APICIDs on SGI UV systems. The location of the
node number within the apicid is now a function of the
processor type.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20110110195210.GA18737@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (30 commits)
gameport: use this_cpu_read instead of lookup
x86: udelay: Use this_cpu_read to avoid address calculation
x86: Use this_cpu_inc_return for nmi counter
x86: Replace uses of current_cpu_data with this_cpu ops
x86: Use this_cpu_ops to optimize code
vmstat: User per cpu atomics to avoid interrupt disable / enable
irq_work: Use per cpu atomics instead of regular atomics
cpuops: Use cmpxchg for xchg to avoid lock semantics
x86: this_cpu_cmpxchg and this_cpu_xchg operations
percpu: Generic this_cpu_cmpxchg() and this_cpu_xchg support
percpu,x86: relocate this_cpu_add_return() and friends
connector: Use this_cpu operations
xen: Use this_cpu_inc_return
taskstats: Use this_cpu_ops
random: Use this_cpu_inc_return
fs: Use this_cpu_inc_return in buffer.c
highmem: Use this_cpu_xx_return() operations
vmstat: Use this_cpu_inc_return for vm statistics
x86: Support for this_cpu_add, sub, dec, inc_return
percpu: Generic support for this_cpu_add, sub, dec, inc_return
...
Fixed up conflicts: in arch/x86/kernel/{apic/nmi.c, apic/x2apic_uv_x.c, process.c}
as per Tejun.
They are a handful of places in the code that register a die_notifier
as a catch all in case no claims the NMI. Unfortunately, they trigger
on events like DIE_NMI and DIE_NMI_IPI, which depending on when they
registered may collide with other handlers that have the ability to
determine if the NMI is theirs or not.
The function unknown_nmi_error() makes one last effort to walk the
die_chain when no one else has claimed the NMI before spitting out
messages that the NMI is unknown.
This is a better spot for these devices to execute any code without
colliding with the other handlers.
The two drivers modified are only compiled on x86 arches I believe, so
they shouldn't be affected by other arches that may not have
DIE_NMIUNKNOWN defined.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: openipmi-developer@lists.sourceforge.net
Cc: dann frazier <dannf@hp.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294348732-15030-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Go through x86 code and replace __get_cpu_var and get_cpu_var
instances that refer to a scalar and are not used for address
determinations.
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
UV systems can be partitioned into multiple independent SSIs.
Large partitioned systems may have extra bits in the node_id
register. These bits are used when the total memory on all SSIs
exceeds 16TB. These extra bits need to be ignored when
calculating x2apic_extra_bits.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20101130195926.972776133@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Early in boot, reading MMRs from the UV hub controller require
calls to early_ioremap()/early_iounmap(). Rather than
duplicating code, add a common function to do the
map/read/unmap.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20101130195926.834804371@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch for SGI UV systems addresses a problem whereby
interrupt transactions being looped back from a local IOH,
through the hub to a local CPU can (erroneously) conflict with
IO port operations and other transactions.
To workaound this we set a high bit in the APIC IDs used for
interrupts. This bit appears to be ignored by the sockets, but
it avoids the conflict in the hub.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
LKML-Reference: <20101116222352.GA8155@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
___
arch/x86/include/asm/uv/uv_hub.h | 4 ++++
arch/x86/include/asm/uv/uv_mmrs.h | 19 ++++++++++++++++++-
arch/x86/kernel/apic/x2apic_uv_x.c | 25 +++++++++++++++++++++++--
arch/x86/platform/uv/tlb_uv.c | 2 +-
arch/x86/platform/uv/uv_time.c | 4 +++-
5 files changed, 49 insertions(+), 5 deletions(-)
A new version of the SGI UV hub node controller is being
developed. A few of the MMRs (control registers) that exist on
the current hub no longer exist on the new hub. Fortunately,
there are alternate MMRs that are are functionally equivalent
and that exist on both hubs.
This patch changes the UV code to use MMRs that exist in BOTH
versions of the hub node controller.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20101106204056.GA27584@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Enable Westmere support for all APIC modes on SGI UV.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20101028224132.GB15804@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Enable Westmere support on SGI UV. The UV initialization code is dependent on
the APICID bits. Westmere-EX uses different APIC bit mapping than Nehalem-EX.
This code reads the apic shift value from a UV MMR to do the proper bit
decoding to determint the pnode.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20101026212728.GB15071@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Fix calculation of "max_pnode" for systems where the the highest
blade has neither cpus or memory. (And, yes, although rare this
does occur).
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20100910150808.GA19802@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
UV NMI callback's should not write stack dumps when a kdump is to be written.
When invoking the crash kernel to write a dump, kdump_nmi_shootdown_cpus()
uses NMI's to get all the cpu's to save their register context and halt.
But the NMI interrupt handler runs a callback list. This patch sets a flag
to prevent any of those callbacks from interfering with the halt of the cpu.
For UV, which currently has the only callback to which this is relevant, the
uv_handle_nmi() callback should not do dumping of stacks.
The 'in_crash_kexec' flag is defined as an extern in kdebug.h firstly
because x2apic_uv_x.c includes it. Secondly because some future callback
might need the flag to know that it should not enter the debugger.
(Such a scenario was in fact present in the 2.6.32 kernel, SuSE distribution,
where a call to kdb needed to be avoided.)
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1ObLvt-0005UZ-Va@eag09.americas.sgi.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
SGI:UV: Delete extra boot messages that describe the system
topology. These messages are no longer useful.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20100317154038.GA29346@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, k8 nb: Fix boot crash: enable k8_northbridges unconditionally on AMD systems
x86, UV: Fix target_cpus() in x2apic_uv_x.c
x86: Reduce per cpu warning boot up messages
x86: Reduce per cpu MCA boot up messages
x86_64, cpa: Don't work hard in preserving kernel 2M mappings when using 4K already
target_cpu() should initially target all cpus, not just cpu 0.
Otherwise systems with lots of disks can exhaust the interrupt
vectors on cpu 0 if a large number of disks are discovered
before the irq balancer is running.
Note: UV code only...
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20100311184328.GA21433@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, uv: Remove recursion in uv_heartbeat_enable()
x86, uv: uv_global_gru_mmr_address() macro fix
x86, uv: Add serial number parameter to uv_bios_get_sn_info()
Enable NMI on all cpus in UV system and add an NMI handler
to dump_stack on each cpu.
By default on x86 all the cpus except the boot cpu have NMI
masked off. This patch enables NMI on all cpus in UV system
and adds an NMI handler to dump_stack on each cpu. This
way if a system hangs we can NMI the machine and get a
backtrace from all the cpus.
Version 2: Use x86_platform driver mechanism for nmi init, per
Ingo's suggestion.
Version 3: Clean up Ingo's nits.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20100226164912.GA24439@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add function to direct Legacy VGA I/O traffic to correct I/O Hub.
Signed-off-by: Mike Travis <travis@sgi.com>
LKML-Reference: <201002022238.o12McEbi018727@imap1.linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Ensure that UV hub revision is set for all ACPI modes.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20100115180908.GB7757@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add function for determining the revision id of the SGI UV
node controller chip (HUB). This function is needed in a
subsequent patch.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20100112210904.GA24546@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This fixes the problem of the initialization code not correctly
mapping the entire MMIO space on a UV system. A side effect is
the map_high() interface needed to be changed to accommodate
different address and size shifts.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Cc: <stable@kernel.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4B479202.7080705@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The recursion is not needed and does not improve readability.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
LKML-Reference: <4B45F13E.3040202@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The wrong address was being used to write the SCIR led regs on
remote hubs. Also, there was an inconsistency between how BIOS
and the kernel indexed these regs. Standardize on using the
lower 6 bits of the APIC ID as the index.
This patch fixes the problem of writing to an errant address to
a cpu # >= 64.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@kernel.org
LKML-Reference: <4B3922F9.3060905@sgi.com>
[ v2: fix a number of annoying checkpatch artifacts and whitespace noise ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
John Blackwood reported:
> on an older Dell PowerEdge 6650 system with 8 cpus (4 are hyper-threaded),
> and 32 bit (x86) kernel, once you change the irq smp_affinity of an irq
> to be less than all cpus in the system, you can never change really the
> irq smp_affinity back to be all cpus in the system (0xff) again,
> even though no error status is returned on the "/bin/echo ff >
> /proc/irq/[n]/smp_affinity" operation.
>
> This is due to that fact that BAD_APICID has the same value as
> all cpus (0xff) on 32bit kernels, and thus the value returned from
> set_desc_affinity() via the cpu_mask_to_apicid_and() function is treated
> as a failure in set_ioapic_affinity_irq_desc(), and no affinity changes
> are made.
set_desc_affinity() is already checking if the incoming cpu mask
intersects with the cpu online mask or not. So there is no need
for the apic op cpu_mask_to_apicid_and() to check again
and return BAD_APICID.
Remove the BAD_APICID return value from cpu_mask_to_apicid_and()
and also fix set_desc_affinity() to return -1 instead of using BAD_APICID
to represent error conditions (as cpu_mask_to_apicid_and() can return
logical or physical apicid values and BAD_APICID is really to represent
bad physical apic id).
Reported-by: John Blackwood <john.blackwood@ccur.com>
Root-caused-by: John Blackwood <john.blackwood@ccur.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1261103386.2535.409.camel@sbs-t61>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add system_serial_number to the information returned by
uv_bios_get_sn_info() UV BIOS call.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20091217165323.GA30774@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
x86, mm: Correct the implementation of is_untracked_pat_range()
x86/pat: Trivial: don't create debugfs for memtype if pat is disabled
x86, mtrr: Fix sorting of mtrr after subtracting
x86: Move find_smp_config() earlier and avoid bootmem usage
x86, platform: Change is_untracked_pat_range() to bool; cleanup init
x86: Change is_ISA_range() into an inline function
x86, mm: is_untracked_pat_range() takes a normal semiclosed range
x86, mm: Call is_untracked_pat_range() rather than is_ISA_range()
x86: UV SGI: Don't track GRU space in PAT
x86: SGI UV: Fix BAU initialization
x86, numa: Use near(er) online node instead of roundrobin for NUMA
x86, numa, bootmem: Only free bootmem on NUMA failure path
x86: Change crash kernel to reserve via reserve_early()
x86: Eliminate redundant/contradicting cache line size config options
x86: When cleaning MTRRs, do not fold WP into UC
x86: remove "extern" from function prototypes in <asm/proto.h>
x86, mm: Report state of NX protections during boot
x86, mm: Clean up and simplify NX enablement
x86, pageattr: Make set_memory_(x|nx) aware of NX support
x86, sleep: Always save the value of EFER
...
Fix up conflicts (added both iommu_shutdown and is_untracked_pat_range)
to 'struct x86_platform_ops') in
arch/x86/include/asm/x86_init.h
arch/x86/kernel/x86_init.c
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
x86, apic: Enable lapic nmi watchdog on AMD Family 11h
x86: Remove unnecessary mdelay() from cpu_disable_common()
x86, ioapic: Document another case when level irq is seen as an edge
x86, ioapic: Fix the EOI register detection mechanism
x86, io-apic: Move the effort of clearing remoteIRR explicitly before migrating the irq
x86: SGI UV: Map low MMR ranges
x86: apic: Print out SRAT table APIC id in hex
x86: Re-get cfg_new in case reuse/move irq_desc
x86: apic: Remove not needed #ifdef
x86: io-apic: IO-APIC MMIO should not fail on resource insertion
x86: Remove asm/apicnum.h
x86: apic: Do not use stacked physid_mask_t
x86, apic: Get rid of apicid_to_cpu_present assign on 64-bit
x86, ioapic: Use snrpintf while set names for IO-APIC resourses
x86, apic: Use PAGE_SIZE instead of numbers
x86: Remove local_irq_enable()/local_irq_disable() in fixup_irqs()
x86: Use EOI register in io-apic on intel platforms
x86: Force irq complete move during cpu offline
x86: Remove move_cleanup_count from irq_cfg
x86, intr-remap: Avoid irq_chip mask/unmask in fixup_irqs() for intr-remapping
...
The semantics the PAT code expect of is_untracked_pat_range() is "is
this range completely contained inside the untracked region." This
means that checkin 8a27138924 was
technically wrong, because the implementation needlessly confusing.
The sane interface is for it to take a semiclosed range like just
about everything else (as evidenced by the sheer number of "- 1"'s
removed by that patch) so change the actual implementation to match.
Reported-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <20091119202341.GA4420@sgi.com>
Explicitly mmap the UV chipset MMR address ranges used to
access blade-local registers. Although these same MMRs are also
mmaped at higher addresses, the low range is more
convenient when accessing blade-local registers.
The low range addresses always alias to the local blade
regardless of the blade id.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20091125162018.GA25445@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- Change is_untracked_pat_range() to return bool.
- Clean up the initialization of is_untracked_pat_range() -- by default,
we simply point it at is_ISA_range() directly.
- Move is_untracked_pat_range to the end of struct x86_platform, since
it is the newest field.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20091119202341.GA4420@sgi.com>
GRU space is always mapped as WB in the page table. There is
no need to track the mappings in the PAT. This also eliminates
the "freeing invalid memtype" messages when the GRU space is
unmapped.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20091119202341.GA4420@sgi.com>
[ v2: fix build failure ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A few parts of the uv_hub_info structure are initialized
incorrectly.
- n_val is being loaded with m_val.
- gpa_mask is initialized with a bytes instead of an unsigned long.
- Handle the case where none of the alias registers are used.
Lastly I converted the bau over to using the uv_hub_info->m_val
which is the correct value.
Without this patch, booting a large configuration hits a
problem where the upper bits of the gnode affect the pnode
and the bau will not operate.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
Cc: Cliff Whickman <cpw@sgi.com>
Cc: stable@kernel.org
LKML-Reference: <20091015224946.396355000@alcatraz.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
UV depends on the MMRHI space being identity mapped. The patch:
x86: Make 64-bit efi_ioremap use ioremap on MMIO regions
changed this to make efi regions at a different address using
ioremap. Add the identity mapping to uv_system_init.
( Note this code was previously present but was deleted when BIOS
added the ranges to the EFI map - previous efi code identify
mapped the ranges. )
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090909154339.GA7946@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The function uv_acpi_madt_oem_check() has been marked __init,
the struct apic_x2apic_uv_x has been marked __refdata.
The aim is to address the following section mismatch messages:
WARNING: arch/x86/kernel/apic/built-in.o(.data+0x1368): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/x86/kernel/built-in.o(.data+0x68e8): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/x86/built-in.o(.text+0x7b36f): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_ioremap()
The function uv_acpi_madt_oem_check() references
the function __init early_ioremap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_ioremap is wrong.
WARNING: arch/x86/built-in.o(.text+0x7b38d): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_iounmap()
The function uv_acpi_madt_oem_check() references
the function __init early_iounmap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_iounmap is wrong.
WARNING: arch/x86/built-in.o(.data+0x8668): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
LKML-Reference: <200908161855.48302.lpotenza@inwind.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change SGI UV default apicid mode to "physical". This is
required to match settings in the UV hub chip.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090727143856.GA8905@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
