Fix the retrn value check which testing the wrong variable
in mmp2_clk_init().
Fixes: 1ec770d92a ("clk: mmp: add mmp2 DT support for clock driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The boot-time frequency of a CPU is considered its rated maximum, as we
have no other source of such information. However, this was previously
only used for chips with 80% restrictions on secondary PLLs. This
usually wasn't a problem because most chips/configs boot with a divider
of /1, with other dividers being used only for dynamic frequency
reduction. However, at least one config (LS1021A at less than 1 GHz)
uses a different divider for top speed. This was causing cpufreq to set
a frequency beyond the chip's rated speed.
This is fixed by applying a 100%-of-initial-speed limit to all CPU PLLs,
similar to the existing 80% limit that only applied to some.
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYExRoEBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYEwIgf8
CHYShoQVgCm/GF9Qg2RrhbeU0PZBKzoltBojZQJYgd16pCiXWRBRMaUSaxJI+p+N
VYqLbrtCgQoIX5d8a3z7K1PgVpDgLH/qKXBAjZ74VSJEcVQuZn9dGfzjtiTgW4eD
0QNItlKH/bZ4VmR+KAu1wkmTz9hVIvN7K0lnJjP/+xQT2A6nX3NjE3o/wA6ZLvWR
Fwk6LSJ28wZNkDbG0HGY9Jeew2oOSm3jxE+8/CK6lGMtBA1yhXXVmDcFklw4MQlp
Hx7Bt0MZT6Nl+dMViAwjZz+MpLpG72gXxG7M8SvftfHg7nKhgUleD+axEkVlKE0C
Yd8/QpEx7lpXvdf8GZ1V/w==
=hBXv
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rockchip-clkfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-fixes
Fix return value in error case of new ddrclk type.
* tag 'v4.9-rockchip-clkfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: don't return NULL when failing to register ddrclk branch
Since 'parent_rate * mfn' may overflow 32 bits, the result should be
stored using 64 bits.
The problem was discovered when trying to set the rate of the audio PLL
(pll4_post_div) on an i.MX6Q. The desired rate was 196.608 MHz, but
the actual rate returned was 192.000570 MHz. The round rate function should
have been able to return 196.608 MHz, i.e., the desired rate.
Fixes: ba7f4f557e ("clk: imx: correct AV PLL rate formula")
Cc: Anson Huang <b20788@freescale.com>
Signed-off-by: Emil Lundmark <emil@limesaudio.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
ioremaped addresses are not linearly mapped so the physical
address can not be figured out via __pa. More generally, there
is no guarantee that backing value of an ioremapped address
is a physical address at all. The value here is only used
for debugging so just drop the call to __pa on the ioremapped
address.
Fixes: 6ae5fd3812 ("clk: xgene: Silence sparse warnings")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Loc Ho <lho@apm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Exynos PMU node is an interrupt, clock and PMU (Power Management Unit)
controller, and these functionalities are supported by different drivers
that matches the same compatible strings.
Since commit 989eafd0b6 ("clk: core: Avoid double initialization of
clocks") the OF core flags clock controllers registered with the
CLK_OF_DECLARE() macro as OF_POPULATED, so platform devices with the same
compatible string will not be registered.
This prevents the PMU platform device to be created, so the Exynos PMU
driver is never probed. This breaks (among other things) Suspend-to-RAM.
Fix this by changing CLKOUT driver initialization method to
CLK_OF_DECLARE_DRIVER(), which doesn't clear the OF_POPULATED flag, so
later a platform device is created and the Exynos PMU platform driver
can be be probed properly.
Fixes: 989eafd0b6 ("clk: core: Avoid double initialization of clocks")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If 'clk_hw_register()' fails, it is likely that we expect to return an
error instead of a valid pointer (which would mean success).
Fix commit f5644f10dc ("clk: at91: Migrate to clk_hw based registration
and OF APIs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
I made a mistake as for naming for this block. The MIO block is not
implemented for these 3 SoCs in the first place. The current naming
will be a trouble if an SoC with both MIO and SD-ctrl blocks appear
in the future.
This driver has just been merged in the previous merge window.
Rename it before the release.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The first loop of this "for" statement writes memory beyond the
allocated clk_hw_onecell_data.
It should be:
for (clk_num--; clk_num >= 0; clk_num--)
...
Or more simply:
while (--clk_num >= 0)
...
Fixes: 734d82f4a6 ("clk: uniphier: add core support code for UniPhier clock driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The hi6220-sysctrl and hi6220-mediactrl are not only clock provider but
also reset controller. It worked fine that single sysctrl/mediactrl
device node in DT can be used to initialize clock driver and populate
platform device for reset controller. But it stops working after
commit 989eafd0b6 ("clk: core: Avoid double initialization of clocks")
gets merged. The commit sets flag OF_POPULATED during clock
initialization to skip the platform device populating for the same
device node. On hi6220, it effectively makes hi6220-sysctrl reset
driver not probe any more.
The patch changes hi6220 sysctrl and mediactrl clock init macro from
CLK_OF_DECLARE to CLK_OF_DECLARE_DRIVER, so that the reset driver using
the same hardware block can continue working.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
For the gate part of the peripheral clock setting the bit disables the
clock and clearing it enables the clock. This is not the default behavior
of clk_gate component, so we need to use the CLK_GATE_SET_TO_DISABLE flag.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: 8ca4746a78 ("clk: mvebu: Add the peripheral clock driver for Armada 3700")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fixes setting low-resolution video modes on HDMI. Now the PLLH_PIX
divider adjusts itself until the PLLH is within bounds.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The commit 9b4cac33ad ("clk: max77686: Migrate to clk_hw based OF and
registration APIs") converted the driver to use the new provider API to
register clocks using clk_hw.
But unfortunately, in the conversion it missed to set the num_clks value
which lead to the following error when trying to register a clk provider:
[ 1.963782] of_clk_max77686_get: invalid index 0
[ 1.967460] ERROR: could not get clock /rtc@10070000:rtc_src(1)
[ 1.973638] s3c-rtc 10070000.rtc: failed to find rtc source clock
Fix it by correctly set the max77686_clk_driver_data num_clks member.
Fixes: 9b4cac33ad ("clk: max77686: Migrate to clk_hw based OF and registration APIs")
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
While trying using a peripheral clock on a driver, I saw that the clock
pointer returned by the provider was NULL.
The problem was a missing indirection. It was the pointer stored in the
hws array which needed to be updated not the value it contains.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: 8ca4746a78 ("clk: mvebu: Add the peripheral clock driver for Armada 3700")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Only propose the mediatek clock drivers on this platform, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Shunli Wang <shunli.wang@mediatek.com>
Cc: James Liao <jamesjj.liao@mediatek.com>
Cc: Erin Lo <erin.lo@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/clk/samsung/clk-exynos-audss.ko | grep alias
alias: platform:exynos-audss-clk
After this patch:
$ modinfo drivers/clk/samsung/clk-exynos-audss.ko | grep alias
alias: platform:exynos-audss-clk
alias: of:N*T*Csamsung,exynos5420-audss-clockC*
alias: of:N*T*Csamsung,exynos5420-audss-clock
alias: of:N*T*Csamsung,exynos5410-audss-clockC*
alias: of:N*T*Csamsung,exynos5410-audss-clock
alias: of:N*T*Csamsung,exynos5250-audss-clockC*
alias: of:N*T*Csamsung,exynos5250-audss-clock
alias: of:N*T*Csamsung,exynos4210-audss-clockC*
alias: of:N*T*Csamsung,exynos4210-audss-clock
Fixes: 4d252fd571 ("clk: samsung: Allow modular build of the Audio Subsystem CLKCON driver")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The 3rd argument of regmap_read() takes a pointer to unsigned int.
This driver is saved just because u32 happens to be typedef'ed as
unsigned int, but we should not rely on that fact. Change the
variable type just in case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
I do not know why, but I missed to add this compatible string in
the initial commit of this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
rockchip_clk_register_ddrclk should not return NULL when failing
to call clk_register, otherwise rockchip_clk_register_branches
prints "unknown clock type". The actual case is that it's a known
clock type but we fail to register it, which may makes user confuse
the reason of failure. And the pr_err here is pointless as
rockchip_clk_register_branches will also print the similar message.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been
merged for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and
usb driver changes are required and included here, and also
the clk tree changes.
- The Allwinner platforms have seen a large-scale change to their
clk drivers and the dts file updates must come after that.
This includes the newly added Nextthing GR8 platform, which is
derived from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't
added until just before the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAV/gzeGCrR//JCVInAQKVhw/5AS5R2S7m7VTlWMvGjvH9ITudYhiAGJP1
z5nP5SwJsfmSjfvw0kSxGUmsNS3rHutsPMz65EesKqFuC3LPZiqMUqrzxt9iqqJx
I+XdAxDTnOE1RBZFtB9dL+qLzHQ87pMo6R9dfs32sxb3QuCQBYhcFyLmQDuZuHH0
yeDi3ARFvgxx/qoRUA7cnSlY5RLNzM44y+Ik/ZcVr4ReqYBC2g5mGi5htoiNSLWR
nwWR+5hNLAp44OZgkZfNsf6kB9brWDQh3PbnBjy6sKXSBoSVIfxTweh2DMJXbZ7l
1Ck+S7WyLMhGJp448TcuBykr/l9i3uqNh061XavjwP8CAjAdZ787XlnNSztc2pyh
dvbI/E76pLGb5ZoFdqlY2Syl63ZFN4K8mjZMSPYfYKf85EDIxe4MYwpbo7/pwzh3
8OlBwH6r4aUMw+QgE1nx8nsjaCoGDMFdgJeJJaWdriZ6Nst2n5gREk/mzbrAWkNG
ujChn/6hES9LuE21aCp1ipB7qnnyeRinfqz2acEFxMQxuPdjwKrdJqNsBaTWsapE
Z+b/BFP+LTdPfHCmMSVwfMrNbwsoY7+L4EXXL36lUgOwcDp0vCXA+PiiahYASewA
1LDQ3CURCEapdBhVU+06Kb4y5eWU7M7EqpOwpHgRJ92dVxgNxuCfcurvxzqPP1UP
3O4R7bfUTTg=
=OmAu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
Driver updates for ARM SoCs, including a couple of newly added drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for the
EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GvTq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion
of old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files.
If no regressions are found, another large cleanup for the platform
will happen as a follow-up, removing dead code and restructuring
the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now DT-only.
The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT
in principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress.
We can probably merge the remaining code into a single directory
in the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then.
Conflicts: two files deleted here have been modified upstream,
the changes can be discarded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WaLy
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion of
old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files. If no regressions are found, another
large cleanup for the platform will happen as a follow-up, removing
dead code and restructuring the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now
DT-only. The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT in
principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress. We
can probably merge the remaining code into a single directory in
the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: select PCI_DOMAINS config from ARCH_MULTIPLATFORM
ARM: stop *MIGHT_HAVE_PCI* config from being selected redundantly
ARM: imx: (trivial) fix typo and grammar
ARM: clps711x: remove extraneous files
ARM: imx: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP2+: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP1: use IS_ENABLED() instead of checking for built-in or module
ARM: imx: remove platform-mxc_rnga
ARM: realview: imply device tree boot
ARM: realview: no need to select SMP_ON_UP explicitly
ARM: realview: delete the RealView board files
ARM: imx: no need to select SMP_ON_UP explicitly
ARM: i.MX: Move SOC_IMX1 into 'Device tree only'
ARM: i.MX: Remove i.MX1 non-DT support
ARM: i.MX: Remove i.MX1 Synertronixx SCB9328 board support
ARM: i.MX: Remove i.MX1 Armadeus APF9328 board support
ARM: mxs: remove obsolete startup code for TX28
ARM: i.MX31 iomux: remove duplicates with alternate name
ARM: i.MX31 iomux: remove plain duplicates
ARM: OMAP2+: Drop legacy board file for LDP
...
This patch adds clock support to Loongson1C SoC.
Signed-off-by: Yang Ling <gnaygnil@gmail.com>
Acked-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make use of GENMASK instead of open coding the equivalent operation,
and update the PLL formula.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch updates some clock names of Loongson1B,
and adds AC97, DMA and NAND clock.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Factor out the common functions into loongson1/clk.c
to support both Loongson1B and Loongson1C. And, put
the rest into loongson1/clk-loongson1b.c.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock driver should be registered with an earlier initcall than
module_init which is used by most of client device drivers. Otherwise,
probing of these client drivers will likely be deferred due to that
calls into clk API will return -EPROBE_DEFER.
Deferred probing is not a problem for most subsystems, but could bring
some side effect for particular subsystem, like display. On ZX296718
platform, we get Linux logo and boot log lost from display device, just
because the DRM/KMS driver gets -EPROBE_DEFER from devm_clk_get() call.
Let's use core_initcall (qcom and a few other clk drivers use that) for
driver registration to avoid those unnecessary -EPROBE_DEFER and get rid
of the side effect with ZX296718 display system.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Original commit, which added support for Armada CP110 system controller
used global variables for storing all clock information. It worked
fine for Armada 7k SoC, with single CP110 block. After dual-CP110 Armada 8k
was introduced, the data got overwritten and corrupted.
This patch fixes the issue by allocating resources dynamically in the
driver probe and storing it as platform drvdata.
Fixes: d3da3eaef7 ("clk: mvebu: new driver for Armada CP110 system ...")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Armada CP110 system controller comprises its own routine responsble
for registering gate clocks. Among others 'flags' field in
struct clk_init_data was not set, using a random values, which
may cause an unpredicted behavior.
This patch fixes the problem by resetting all fields of clk_init_data
before assigning values for all gated clocks of Armada 7k/8k SoCs family.
Fixes: d3da3eaef7 ("clk: mvebu: new driver for Armada CP110 system ...")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Free memory mapping, if lpc32xx_clk_init is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Referring to the u-boot sources for the Netgear WNR854T, add support
for the mv88f5181.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Free memory mapping if init is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There's been a copy and paste mistake in the A23 and A33 from the H3,
leading in the reset offset for the UART and I2C.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Assume that if the oscillator is enabled (OSC32EN bit is present), the
delay has already elapsed as the bootloader probably waited for the
oscillator to settle. This could waste up to 1.2s.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Starting with sama5d4, the crystal oscillator is always enabled at startup
and the SCKC doesn't have an OSC32EN bit anymore.
Add support for that new controller.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Move all clocks related to the slow clock controller to sckc.c. This avoids
extern definitions and allows to remove sckc.h
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[sboyd@codeaurora.org: Mark some functions static]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Initialize the GPU clock muxes to sane inputs. Until now they have
not been changed from their default values, which means that both
GPU3D shader and GPU2D core were fed by clock inputs whose rates
exceed the maximium allowed frequency of the cores by as much as
200MHz.
This fixes a severe GPU stability issue on i.MX6DL.
Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current clock tree only implements the minimal set of differences
between the i.MX6Q and the i.MX6DL, but that doesn't really reflect
reality.
Apply the following fixes to match the RM:
- DL has no GPU3D_SHADER_SEL/PODF, the shader domain is clocked by
GPU3D_CORE
- GPU3D_SHADER_SEL/PODF has been repurposed as GPU2D_CORE_SEL/PODF
- GPU2D_CORE_SEL/PODF has been repurposed as MLB_SEL/PODF
Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- media: update IR support for newer SoCs
- firmware: add secure monitor driver
- net: new stmmac glue driver
- usb: udd DWC2 support for meson-gxbb
- clocks: expose more clock IDs for use by DT
- DT binding updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DlpW
-----END PGP SIGNATURE-----
Merge tag 'amlogic-drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/late
Pull "Amlogic driver updates for v4.9, 2nd round" from Kevin Hilman:
- media: update IR support for newer SoCs
- firmware: add secure monitor driver
- net: new stmmac glue driver
- usb: udd DWC2 support for meson-gxbb
- clocks: expose more clock IDs for use by DT
- DT binding updates
* tag 'amlogic-drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (21 commits)
clk: gxbb: expose i2c clocks
clk: gxbb: expose USB clocks
clk: gxbb: expose spifc clock
clk: gxbb: expose MPLL2 clock for use by DT
Documentation: dt-bindings: Add documentation for the Meson USB2 PHYs
usb: dwc2: add support for Meson8b and GXBB SoCs
net: stmmac: update the module description of the dwmac-meson driver
net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC
stmmac: introduce get_stmmac_bsp_priv() helper
net: dt-bindings: Document the new Meson8b and GXBB DWMAC bindings
clk: meson-gxbb: Export PWM related clocks for DT
meson: clk: Add support for clock gates
gxbb: clk: Adjust MESON_GATE macro to be shared with meson8b
clk: meson: Copy meson8b CLKID defines to private header file
meson: clk: Rename register names according to Amlogic datasheet
meson: clk: Move register definitions to meson8b.h
clk: meson: Rename meson8b-clkc.c to reflect gxbb naming convention
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
media: rc: meson-ir: Add support for newer versions of the IR decoder
...
Add clock data arrays for all UniPhier SoCs with a binding document.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This includes UniPhier clock driver code, except SoC-specific
data arrays.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clock is present on BCM53573 devices (including BCM47189) that use
Cortex-A7. ILP is a part of PMU (Power Management Unit) multi-function
device so we use syscon (and regmap) for it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@codeaurora.org: Remove 0 from clk_init_data to silence sparse]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The zx296718 clock driver has a creative way of assigning the register
values for each clock, by initializing an __iomem pointer to an
offset and then later adding the base (from ioremap) on top
with a cast to u64. This fail on all 32-bit architectures during
compile testing:
drivers/clk/zte/clk-zx296718.c: In function 'top_clocks_init':
drivers/clk/zte/clk-zx296718.c:554:35: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
zx296718_pll_clk[i].reg_base += (u64)reg_base;
drivers/clk/zte/clk-zx296718.c:579:29: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/clk/zte/clk-zx296718.c:592:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
It would be nice to avoid all the casts, but I decided to simply
shut up the warnings by changing the type from u64 to uintptr_t,
which does the right thing in practice.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ca0233285a ("clk: zx: register ZX296718 clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use the builtin_platform_driver() macro to make the code simpler.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The register offset for the mipi-csi clk is off by 4, a copy paste
error from the mipi-dsi clk.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The PLLs have a "lock" bit in their configuration registers which
indicate if the PLL has locked on to the requested clock rate. We
check this bit in the .set_rate op. The PLL cannot lock on if it's
not running, which might be a false positive (warning).
Set the CLK_SET_RATE_UNGATE flag for all PLLs so whenever clk_set_rate
is called on them, they get enabled and the "lock" check is really
checking the PLL.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The LCD controller and HDMI controller use the LCDx-CHy and HDMI clocks
to generate their dot clocks. To be able to generate a full range of
possible clock rates, the parent PLL clock rates should also be changed.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
