Simplify and cleanup the sysfs code a bit.
[m.chehab@samsung.com: rebased and fixed a CodingStyle issue]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver codes the two address bytes in reverse order when compared to the
other drivers, so make it consistent (and update the keymap, note that the
result is a prefix change from 0x6b86 -> 0x866b, and the latter is pretty
common among the NECX keymaps. While not conclusive, it's still a strong hint
that the change is correct).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
the RC RX packet is defined as:
struct dib0700_rc_response {
...
u8 not_system;
u8 system;
...
u8 data;
u8 not_data;
The NEC protocol transmits in the order:
system
not_system
data
not_data
Note that the code defines the NEC extended scancode as:
scancode = be16_to_cpu(poll_reply->system16) << 8 | poll_reply->data;
i.e.
scancode = poll_reply->not_system << 16 |
poll_reply->system << 8 |
poll_reply->data;
Which, if the order *is* reversed, would mean that the scancode that
gets defined is in reality:
scancode = poll_reply->system << 16 |
poll_reply->not_system << 8 |
poll_reply->data;
Which is the same as the order used in drivers/media/rc/ir-nec-decoder.c.
This patch changes the code to match my assumption (the generated scancode
should, however, not change).
[m.chehab@samsung.com: rebased and fixed the decoding error message]
Signed-off-by: David Härdeman <david@hardeman.nu>
CC: Patrick Boettcher <pboettcher@kernellabs.com>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The arguments used for ir-kbd-i2c's get_key() functions are not
really suited for rc-core and the ir_raw/ir_key distinction is
just confusing.
Convert all of them to return a protocol/scancode/toggle triple instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The bt8xx driver does RC5 decoding for Nebula digi hardware, but includes
some pointless limitations (both start bits must be one, the
device/address/system must be 0x00). Remove those limitations and update
the keymap to use the full RC5 scancode (fortunately the 0x00 address
means that this is perfectly backwards compatible).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Vincent:
[ 16.332247] xc2028 0-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000.
[ 16.344378] cxusb: i2c wr: len=64 is too big!
64 bytes is too short for firmware load on this device. So, increase it
to 80 bytes.
Reported-by: Vincent McIntyre <vincent.mcintyre@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The DocBook documentation is incorrect: on ISDB-T, interleaving
time is always a power of 2. Fix it and provides a table showing
the actual interleaving length for each mode.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The programmed frequency on xc4000 is not the middle
frequency, but the initial frequency on the bandwidth range.
However, the DVB API works with the middle frequency.
This works fine on set_frontend, as the device calculates
the needed offset. However, at get_frequency(), the returned
value is the initial frequency. That's generally not a big
problem on most drivers, however, starting with changeset
6fe1099c7a, the frequency drift is taken into account at
dib7000p driver.
This broke support for PCTV 340e, with uses dib7000p demod and
xc4000 tuner.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The programmed frequency on xc5000 is not the middle
frequency, but the initial frequency on the bandwidth range.
However, the DVB API works with the middle frequency.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This meta-tag is used by some distros to help them package
the firmware and generate proper initrd images.
So, add the firmware names there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The firmware name at:
http://www.kernellabs.com/firmware/xc4000/
Is different from the one at the Kernel. Update it
try first the new name, falling back to the previous one
if the new name can't be found.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes the null test on ch. ch is initialized at the
beginning of the function to &demod->dtv_property_cache. Since demod
is dereferenced prior to the null test, demod must be a valid pointer,
and &demod->dtv_property_cache cannot be null.
The following Coccinelle script is used for detecting the change:
@r@
expression e,f;
identifier g,y;
statement S1,S2;
@@
*e = &f->g
<+...
f->y
...+>
*if (e != NULL || ...)
S1 else S2
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of looking at the guard interval field, it was using
the interval length, with is wrong. Fix it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Interleaving code was wrong at mb86a20s: instead, it was looking
at the Guard Interval. Fix it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver was reporting an incorrect mode, when mode 2
is selected.
While testing it, noticed that neither mode 1 or guard
interval 1/32 is supported by this device. Document it,
and ensure that it will report _AUTO when it doesn't lock,
in order to not report a wrong detection to userspace.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was 32-bit calculation overflow. Use div_u64.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This cleans up some line over 80 character violations.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This removes checks of struct member addresses since they likely result
in the condition always being true. Also in the stb6100_get_bandwidth
and tda8261_get_bandwidth functions the pointers frontend_ops and
tuner_ops are assigned the same addresses twice.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This updated patch also fixes out of bound access to b[].
In dib9000_risc_apb_access_write() an out of bound access to mb[].
The current test to avoid out of bound access to mb[] is insufficient.
For len = 19 non-existent mb[10] will be accessed.
For odd values of len b[] is accessed out of bounds.
For large values of len an of bound access to mb[] may occur in
dib9000_mbx_send_attr.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
>From the context this should be hex 0x80 instead of decimal 80.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
changeset a733291d69 didn't merge the fixes well. It ended by
restoring some bad logic removed there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Kbuildtest:
warning: (VIDEO_PVRUSB2 && VIDEO_TLG2300 && VIDEO_USBVISION && VIDEO_GO7007 && VIDEO_AU0828_V4L2 && VIDEO_CX231XX && VIDEO_TM6000 && VIDEO_EM28XX && VIDEO_IVTV && VIDEO_MXB && VIDEO_CX18 && VIDEO_CX23885 && VIDEO_CX88 && VIDEO_BT848 && VIDEO_SAA7134 && VIDEO_SAA7164) selects VIDEO_TUNER which has unmet direct dependencies (MEDIA_SUPPORT && MEDIA_TUNER)
That happens when:
# CONFIG_MEDIA_ANALOG_TV_SUPPORT is not set
CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
# CONFIG_MEDIA_RADIO_SUPPORT is not set
# CONFIG_MEDIA_SDR_SUPPORT is not set
CONFIG_VIDEO_AU0828_V4L2=y
CONFIG_VIDEO_CX231XX=y
CONFIG_VIDEO_TM6000=y
CONFIG_VIDEO_EM28XX=y
CONFIG_VIDEO_TUNER=y
CONFIG_MEDIA_SUPPORT=y
With means that we need to enable MEDIA_TUNER also when DTV
is enabled. While the above config doesn't cover, if we enable
SDR, the same error can also happen.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that the custom motion detection API in this driver has been
replaced with a standard API there is no reason anymore to keep it
in staging. So (finally!) move it to drivers/media/usb.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that the custom motion detection API has been replaced with a
standard API there is no reason anymore to keep it in staging.
So (finally!) move it to drivers/media/pci.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Similarly to workbuf_size and tempbuf_size, store iram_size in the
coda_devtype structure. This also decreases the IRAM used on i.MX6DL
to 128 KiB.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Similarly to the work buffer size, store the temporary buffer size in the
coda_devtype structure.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We had the workbuf_size field since the beginning.
Use it to tighten the code a little bit.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch exports all auxiliary buffers, including SRAM, as debugfs binary
blobs for debugging purposes. It shows, for example, that psbuf currently
doesn't seem to be used at all on CODA7541, and that slicebuf and workbuf
usage is far from the maximum. It can also be used to validate SRAM size
allocation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When encoding into h.264, the input frame stride needs to be a multiple of 16.
During allocation of the input buffers, it may not be known yet whether the
encoder should create h.264 or not. Assume the worst and always use a frame
stride that is a multiple of 16.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
CODA7541 only supports encoding h.264 frames with width and height that are
multiples of the macroblock size.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Even though the CODA h.264 decoder always decodes complete macroblocks, we can
set the stride to the corresponding multiple of 16 and use a value smaller than
that as real width. Unfortunately the same doesn't work for height, as there
is no vertical linesperframe stride for discontiguous planar YUV frames.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
bytesperline is calculated in multiple places, store it in the coda_q_data
structure. This will be more useful later when adding JPEG support.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On i.MX53 and i.MX6, the CODA VPU can be reset by the System Reset Controller.
We can use this to get out of dire situations, for example after a picture
run timeout.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename the per-context prescan_failed variable to hold, as this is what the
flag does: it temporarily keeps the coda from running until new data is fed
into the bitstream buffer or stop_streaming is called on the input side.
A prescan failure on i.MX5 is one possible reason to enter this state, another
one is a picture run timeout on i.MX6.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The coda h.264 decoder also counts PIC_RUNs where no frame was decoded but
a frame was rotated out / marked as ready to be displayed. This causes an
offset between the incoming encoded frame's sequence number and the decode
sequence number returned by the coda. This patch introduces a sequence
counter offset variable to keep track of the difference.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the CODA reports macroblock errors, also set the VB2_BUF_STATE_ERROR flag
to alert userspace.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The coda driver advertises timestamp_type V4L2_BUF_FLAG_TIMESTAMP_COPY on
both queues, so we have to copy timestamps from input v4l2 buffers to the
corresponding destination v4l2 buffers. Since the h.264 decoder can reorder
frames, a timestamp queue is needed to keep track of and assign the correct
timestamp to destination buffers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In case no further buffers are queued after the stop command, restart
job scheduling explicitly.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some drivers might allow to decode remaining frames from an internal ringbuffer
after a decoder stop command. Allow those to call v4l2_m2m_try_schedule
directly.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Allow userspace to enable cyclic intra refresh by setting the number of
intra macroblocks per frame to a non-zero value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the bitrate control is set, the encoder works in CBR mode, dynamically
changing the quantization parameters to achieve a constant bitrate.
With the min/max QP controls the quantization parameters can be limited
to a given range.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
