Steffen Klassert says:
====================
pull request (net): ipsec 2017-06-23
1) Fix xfrm garbage collecting when unregistering a netdevice.
From Hangbin Liu.
2) Fix NULL pointer derefernce when exiting a network namespace.
From Hangbin Liu.
3) Fix some error codes in pfkey to prevent a NULL pointer derefernce.
From Dan Carpenter.
4) Fix NULL pointer derefernce on allocation failure in pfkey.
From Dan Carpenter.
5) Adjust IPv6 payload_len to include extension headers. Otherwise
we corrupt the packets when doing ESP GRO on transport mode.
From Yossi Kuperman.
6) Set nhoff to the proper offset of the IPv6 nexthdr when doing ESP GRO.
From Yossi Kuperman.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory allocation size is controlled by user-space,
if it is too large just fail silently and return NULL,
not to mention there is a fallback allocation later.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our customer encountered stuck NFS writes for blocks starting at specific
offsets w.r.t. page boundary caused by networking stack sending packets via
UFO enabled device with wrong checksum. The problem can be reproduced by
composing a long UDP datagram from multiple parts using MSG_MORE flag:
sendto(sd, buff, 1000, MSG_MORE, ...);
sendto(sd, buff, 1000, MSG_MORE, ...);
sendto(sd, buff, 3000, 0, ...);
Assume this packet is to be routed via a device with MTU 1500 and
NETIF_F_UFO enabled. When second sendto() gets into __ip_append_data(),
this condition is tested (among others) to decide whether to call
ip_ufo_append_data():
((length + fragheaderlen) > mtu) || (skb && skb_is_gso(skb))
At the moment, we already have skb with 1028 bytes of data which is not
marked for GSO so that the test is false (fragheaderlen is usually 20).
Thus we append second 1000 bytes to this skb without invoking UFO. Third
sendto(), however, has sufficient length to trigger the UFO path so that we
end up with non-UFO skb followed by a UFO one. Later on, udp_send_skb()
uses udp_csum() to calculate the checksum but that assumes all fragments
have correct checksum in skb->csum which is not true for UFO fragments.
When checking against MTU, we need to add skb->len to length of new segment
if we already have a partially filled skb and fragheaderlen only if there
isn't one.
In the IPv6 case, skb can only be null if this is the first segment so that
we have to use headersize (length of the first IPv6 header) rather than
fragheaderlen (length of IPv6 header of further fragments) for skb == NULL.
Fixes: e89e9cf539 ("[IPv4/IPv6]: UFO Scatter-gather approach")
Fixes: e4c5e13aa4 ("ipv6: Should use consistent conditional judgement for
ip6 fragment between __ip6_append_data and ip6_finish_output")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a RAID set was created on dm-raid version < 1.9.0 (old RAID
superblock format), all of the new 1.9.0 members of the superblock are
uninitialized (zero) -- including the device sectors member needed to
support shrinking.
All the other accesses to superblock fields new in 1.9.0 were reviewed
and verified to be properly guarded against invalid use. The 'sectors'
member was the only one used when the superblock version is < 1.9.
Don't access the superblock's >= 1.9.0 'sectors' member unconditionally.
Also add respective comments.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- Do not double the offset of inline expansions when using
'perf probe' on inlined functions (Björn Töpel)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=oZCf
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-4.12-20170622' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull 'perf probe' fix from Arnaldo Carvalho de Melo:
- Do not double the offset of inline expansions when using
'perf probe' on inlined functions (Björn Töpel)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The F54 driver is currently only using the first 6 bytes of F54 so there is
no need to read all 27 bytes. Some Dell systems (Dell XP13 9333 and
similar) have an issue with the touchpad or I2C bus when reading reports
larger then 16 bytes. Reads larger then 16 bytes are reported in two HID
reports. Something about the back to back reports seems to cause the next
read to report incorrect data. This results in F30 failing to load and the
click button failing to work.
Previous issues with the I2C controller or touchpad were addressed in:
commit 5b65c2a029 ("HID: rmi: check sanity of the incoming report")
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=195949
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A previous set of patches "cxl: Add support for Coherent Accelerator
Interface Architecture 2.0" has introduced a new support for the CAPI
cards. These patches have been tested on Simulation environment and
quite a bit of them have been tested on real hardware.
This patch brings new fixes after a series of tests carried out on new
equipment:
- Add POWER9 definition.
- Re-enable any masked interrupts when the AFU is not activated
after resetting the AFU.
- Remove the api cxl_is_psl8/9 which is no longer useful.
- Do not dump CAPI1 registers.
- Rewrite cxl_is_page_fault() function.
- Do not register slb callack on P9.
Fixes: f24be42aab ("cxl: Add psl9 specific code")
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Emergency stacks have their thread_info mostly uninitialised, which in
particular means garbage preempt_count values.
Emergency stack code runs with interrupts disabled entirely, and is
used very rarely, so this has been unnoticed so far. It was found by a
proposed new powerpc watchdog that takes a soft-NMI directly from the
masked_interrupt handler and using the emergency stack. That crashed
at BUG_ON(in_nmi()) in nmi_enter(). preempt_count()s were found to be
garbage.
To fix this, zero the entire THREAD_SIZE allocation, and initialize
the thread_info.
Cc: stable@vger.kernel.org
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Move it all into setup_64.c, use a function not a macro. Fix
crashes on Cell by setting preempt_count to 0 not HARDIRQ_OFFSET]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix sparse warnings in scripts/kconfig/nconf* ('make nconfig'):
../scripts/kconfig/nconf.c:1071:32: warning: Using plain integer as NULL pointer
../scripts/kconfig/nconf.c:1238:30: warning: Using plain integer as NULL pointer
../scripts/kconfig/nconf.c:511:51: warning: Using plain integer as NULL pointer
../scripts/kconfig/nconf.c:1460:6: warning: symbol 'setup_windows' was not declared. Should it be static?
../scripts/kconfig/nconf.c:274:12: warning: symbol 'current_instructions' was not declared. Should it be static?
../scripts/kconfig/nconf.c:308:22: warning: symbol 'function_keys' was not declared. Should it be static?
../scripts/kconfig/nconf.gui.c:132:17: warning: non-ANSI function declaration of function 'set_colors'
../scripts/kconfig/nconf.gui.c:195:24: warning: Using plain integer as NULL pointer
nconf.gui.o before/after files are the same.
nconf.o before/after files are the same until the 'static' function
declarations are added.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In commit 613f050d68 ("perf probe: Fix to probe on gcc generated
functions in modules"), the offset from symbol is, incorrectly, added
to the trace point address. This leads to incorrect probe trace points
for inlined functions and when using relative line number on symbols.
Prior this patch:
$ perf probe -m nf_nat -D in_range
p:probe/in_range nf_nat:in_range.isra.9+0
$ perf probe -m i40e -D i40e_clean_rx_irq
p:probe/i40e_clean_rx_irq i40e:i40e_napi_poll+2212
$ perf probe -m i40e -D i40e_clean_rx_irq:16
p:probe/i40e_clean_rx_irq i40e:i40e_lan_xmit_frame+626
After:
$ perf probe -m nf_nat -D in_range
p:probe/in_range nf_nat:in_range.isra.9+0
$ perf probe -m i40e -D i40e_clean_rx_irq
p:probe/i40e_clean_rx_irq i40e:i40e_napi_poll+1106
$ perf probe -m i40e -D i40e_clean_rx_irq:16
p:probe/i40e_clean_rx_irq i40e:i40e_napi_poll+2665
Committer testing:
Using 'pfunct', a tool found in the 'dwarves' package [1], one can ask what are
the functions that while not being explicitely marked as inline, were inlined
by the compiler:
# pfunct --cc_inlined /lib/modules/4.12.0-rc4+/kernel/drivers/net/ethernet/intel/e1000e/e1000e.ko | head
__ew32
e1000_regdump
e1000e_dump_ps_pages
e1000_desc_unused
e1000e_systim_to_hwtstamp
e1000e_rx_hwtstamp
e1000e_update_rdt_wa
e1000e_update_tdt_wa
e1000_put_txbuf
e1000_consume_page
Then ask 'perf probe' to produce the kprobe_tracer probe definitions for two of
them:
# perf probe -m e1000e -D e1000e_rx_hwtstamp
p:probe/e1000e_rx_hwtstamp e1000e:e1000_receive_skb+74
# perf probe -m e1000e -D e1000_consume_page
p:probe/e1000_consume_page e1000e:e1000_clean_jumbo_rx_irq+876
p:probe/e1000_consume_page_1 e1000e:e1000_clean_jumbo_rx_irq+1506
p:probe/e1000_consume_page_2 e1000e:e1000_clean_rx_irq_ps+1074
Now lets concentrate on the 'e1000_consume_page' one, that was inlined twice in
e1000_clean_jumbo_rx_irq(), lets see what readelf says about the DWARF tags for
that function:
$ readelf -wi /lib/modules/4.12.0-rc4+/kernel/drivers/net/ethernet/intel/e1000e/e1000e.ko
<SNIP>
<1><13e27b>: Abbrev Number: 121 (DW_TAG_subprogram)
<13e27c> DW_AT_name : (indirect string, offset: 0xa8945): e1000_clean_jumbo_rx_irq
<13e287> DW_AT_low_pc : 0x17a30
<3><13e6ef>: Abbrev Number: 119 (DW_TAG_inlined_subroutine)
<13e6f0> DW_AT_abstract_origin: <0x13ed2c>
<13e6f4> DW_AT_low_pc : 0x17be6
<SNIP>
<1><13ed2c>: Abbrev Number: 142 (DW_TAG_subprogram)
<13ed2e> DW_AT_name : (indirect string, offset: 0xa54c3): e1000_consume_page
So, the first time in e1000_clean_jumbo_rx_irq() where e1000_consume_page() is
inlined is at PC 0x17be6, which subtracted from e1000_clean_jumbo_rx_irq()'s
address, gives us the offset we should use in the probe definition:
0x17be6 - 0x17a30 = 438
but above we have 876, which is twice as much.
Lets see the second inline expansion of e1000_consume_page() in
e1000_clean_jumbo_rx_irq():
<3><13e86e>: Abbrev Number: 119 (DW_TAG_inlined_subroutine)
<13e86f> DW_AT_abstract_origin: <0x13ed2c>
<13e873> DW_AT_low_pc : 0x17d21
0x17d21 - 0x17a30 = 753
So we where adding it at twice the offset from the containing function as we
should.
And then after this patch:
# perf probe -m e1000e -D e1000e_rx_hwtstamp
p:probe/e1000e_rx_hwtstamp e1000e:e1000_receive_skb+37
# perf probe -m e1000e -D e1000_consume_page
p:probe/e1000_consume_page e1000e:e1000_clean_jumbo_rx_irq+438
p:probe/e1000_consume_page_1 e1000e:e1000_clean_jumbo_rx_irq+753
p:probe/e1000_consume_page_2 e1000e:e1000_clean_jumbo_rx_irq+1353
#
Which matches the two first expansions and shows that because we were
doubling the offset it would spill over the next function:
readelf -sw /lib/modules/4.12.0-rc4+/kernel/drivers/net/ethernet/intel/e1000e/e1000e.ko
673: 0000000000017a30 1626 FUNC LOCAL DEFAULT 2 e1000_clean_jumbo_rx_irq
674: 0000000000018090 2013 FUNC LOCAL DEFAULT 2 e1000_clean_rx_irq_ps
This is the 3rd inline expansion of e1000_consume_page() in
e1000_clean_jumbo_rx_irq():
<3><13ec77>: Abbrev Number: 119 (DW_TAG_inlined_subroutine)
<13ec78> DW_AT_abstract_origin: <0x13ed2c>
<13ec7c> DW_AT_low_pc : 0x17f79
0x17f79 - 0x17a30 = 1353
So:
0x17a30 + 2 * 1353 = 0x184c2
And:
0x184c2 - 0x18090 = 1074
Which explains the bogus third expansion for e1000_consume_page() to end up at:
p:probe/e1000_consume_page_2 e1000e:e1000_clean_rx_irq_ps+1074
All fixed now :-)
[1] https://git.kernel.org/pub/scm/devel/pahole/pahole.git/
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 613f050d68 ("perf probe: Fix to probe on gcc generated functions in modules")
Link: http://lkml.kernel.org/r/20170621164134.5701-1-bjorn.topel@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull cifs fixes from Steve French:
"Various small fixes for stable"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix some return values in case of error in 'crypt_message'
cifs: remove redundant return in cifs_creation_time_get
CIFS: Improve readdir verbosity
CIFS: check if pages is null rather than bv for a failed allocation
CIFS: Set ->should_dirty in cifs_user_readv()
MIPS:
- Fix build with KVM, DYNAMIC_DEBUG and JUMP_LABEL.
PPC:
- Fix host crashes/hangs on POWER9.
- Properly restore userspace state after KVM_RUN ioctl.
s390:
- Fix address translation in odd-ball cases (real-space designation
ASCEs).
x86:
- Fix privilege escalation in 64-bit Windows guests.
All patches are for stable and the x86 also has a CVE.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJZS9uIAAoJEED/6hsPKofou7UH/1AopK/4WzfZqIlObxf1O2K/
iqeoHlU/7TPz3+YVN4PxCyb9KWxOR1CS6IjmrrQRnl/ncYkFwUI11zb1Dao7mvYo
L/D4XeT9rLheNATj9RPlznIAbQicN3TFWWczMzR0T2kftHHDAe0rWF1hkyS3BDyY
n6V6LbG6h6ONacUHUFfDAgRugiI1rKAjKtOeFvylIS5nIe1ez1ocULBxoXVJFxv1
0XnX/OrWDocGeope0xt6Jmjr7N5cMU0fyjJ+VM4ap8HGmovVUPeXF+cKdaOUyZyS
L+4goghsHDK8fCrtQiPhL+TqQ7El0OtzzcSScb662vT1wd7haAtrQcv96WFAVE4=
=Zhvq
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"MIPS:
- Fix build with KVM, DYNAMIC_DEBUG and JUMP_LABEL.
PPC:
- Fix host crashes/hangs on POWER9.
- Properly restore userspace state after KVM_RUN ioctl.
s390:
- Fix address translation in odd-ball cases (real-space designation
ASCEs).
x86:
- Fix privilege escalation in 64-bit Windows guests
All patches are for stable and the x86 also has a CVE"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix singlestepping over syscall
KVM: s390: gaccess: fix real-space designation asce handling for gmap shadows
KVM: MIPS: Fix maybe-uninitialized build failure
KVM: PPC: Book3S HV: Ignore timebase offset on POWER9 DD1
KVM: PPC: Book3S HV: Save/restore host values of debug registers
KVM: PPC: Book3S HV: Preserve userspace HTM state properly
KVM: PPC: Book3S HV: Restore critical SPRs to host values on guest exit
KVM: PPC: Book3S HV: Context-switch EBB registers properly
KVM: PPC: Book3S HV: Cope with host using large decrementer mode
- Use address passed in, rather than hard coded value
- Correct clock-names value in DT binding documentation
-----BEGIN PGP SIGNATURE-----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=iygS
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
- arizona: use address passed in, rather than hard coded value
- correct STM32 clock-names value in DT binding documentation
* tag 'mfd-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
dt-bindings: mfd: Update STM32 timers clock names
mfd: arizona: Fix typo using hard-coded register
The 8000 series adapters uses catch-all filters for encapsulated traffic
to support filtering VXLAN, NVGRE and GENEVE traffic.
This new filter functionality requires a longer MCDI command.
This patch increases the size of buffers on stack that were missed, which
fixes a kernel panic from the stack protector.
Fixes: 9b41080125 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Acked-by: Bert Kenward bkenward@solarflare.com
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure member is hidden behind CONFIG_SYSFS, and we
get a build error when that is disabled:
drivers/net/hyperv/netvsc_drv.c: In function 'netvsc_set_channels':
drivers/net/hyperv/netvsc_drv.c:754:49: error: 'struct net_device' has no member named 'num_rx_queues'; did you mean 'num_tx_queues'?
drivers/net/hyperv/netvsc_drv.c: In function 'netvsc_set_rxfh':
drivers/net/hyperv/netvsc_drv.c:1181:25: error: 'struct net_device' has no member named 'num_rx_queues'; did you mean 'num_tx_queues'?
As the value is only set once to the argument of alloc_netdev_mq(),
we can compare against that constant directly.
Fixes: ff4a441990 ("netvsc: allow get/set of RSS indirection table")
Fixes: 2b01888d1b ("netvsc: allow more flexible setting of number of channels")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per netns loopback_dev->ip6_ptr is unregistered and set to
NULL when its mtu is set to smaller than IPV6_MIN_MTU, this
leads to that we could set rt->rt6i_idev NULL after a
rt6_uncached_list_flush_dev() and then crash after another
call.
In this case we should just bring its inet6_dev down, rather
than unregistering it, at least prior to commit 176c39af29
("netns: fix addrconf_ifdown kernel panic") we always
override the case for loopback.
Thanks a lot to Andrey for finding a reliable reproducer.
Fixes: 176c39af29 ("netns: fix addrconf_ifdown kernel panic")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladislav Yasevich says:
====================
macvlan: Fix some issues with changing mac addresses
There are some issues in macvlan wrt to changing it's mac address.
* An error is returned in the specified address is the same as an already
assigned address.
* In passthru mode, the mac address of the macvlan device doesn't change.
* After changing the mac address of a passthru macvlan and then removing it,
the mac address of the physical device remains changed.
This patch series attempts to resolve these issues.
V2: Address a small issue in p4 where we save the address from the lowerdev
(from girish.moodalbail@oracle.com)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Passthru macvlans directly change the mac address of the lower
level device. That's OK, but after the macvlan is deleted,
the lower device is left with changed address and one needs to
reboot to bring back the origina HW addresses.
This scenario is actually quite common with passthru macvtap devices.
This patch attempts to solve this, by storing the mac address
of the lower device in macvlan_port structure and keeping track of
it through the changes.
After this patch, any changes to the lower device mac address
done trough the macvlan device, will be reverted back. Any
changs done directly to the lower device mac address will be kept.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the port passthru boolean into flags with accesor functions.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a lower device of the passthru macvlan changes it's address,
passthru macvlan is supposed to change it's own address as well.
However, that doesn't happen correctly because the check in
macvlan_addr_busy() will catch the fact that the lower level
(port) mac address is the same as the address we are trying to
assign to the macvlan, and return an error. As a reasult,
the address of the passthru macvlan device is never changed.
The same thing happens when the user attempts to change the
mac address of the passthru macvlan.
The simple solution appers to be to not check against
the lower device in case of passthru macvlan device, since
the 2 addresses are _supposed_ to be the same.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user currently gets an EBUSY error when attempting to set
the mac address on a macvlan device to the same value.
This should really be a no-op as nothing changes. Catch
the condition and return early.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flag to indicate if a queue is rate-limited. Test the flag in
NAPI poll handler and avoid rescheduling the queue if true, otherwise
we risk locking up the host. The rescheduling will be done in the
timer callback function.
Reported-by: Jean-Louis Dupond <jean-louis@dupond.be>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Tested-by: Jean-Louis Dupond <jean-louis@dupond.be>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are number of problems with configuration peer
network device in absence of IFLA_VETH_PEER attributes
where attributes for main network device shared with
peer.
First it is not feasible to configure both network
devices with same MAC address since this makes
communication in such configuration problematic.
This case can be reproduced with following sequence:
# ip link add address 02:11:22:33:44:55 type veth
# ip li sh
...
26: veth0@veth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc \
noop state DOWN mode DEFAULT qlen 1000
link/ether 00:11:22:33:44:55 brd ff:ff:ff:ff:ff:ff
27: veth1@veth0: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc \
noop state DOWN mode DEFAULT qlen 1000
link/ether 00:11:22:33:44:55 brd ff:ff:ff:ff:ff:ff
Second it is not possible to register both main and
peer network devices with same name, that happens
when name for main interface is given with IFLA_IFNAME
and same attribute reused for peer.
This case can be reproduced with following sequence:
# ip link add dev veth1a type veth
RTNETLINK answers: File exists
To fix both of the cases check if corresponding netlink
attributes are taken from peer_tb when valid or
name based on rtnl ops kind and random address is used.
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpsw driver tries to get macid for am43xx SoCs using the compatible
ti,am4372. But not all variants of am43x uses this complatible like
epos evm uses ti,am438x. So use a generic compatible ti,am43 to get
macid for all am43 based platforms.
Reviewed-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 242d3a49a2 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf")
I assumed NETDEV_REGISTER and NETDEV_UNREGISTER are paired,
unfortunately, as reported by jeffy, netdev_wait_allrefs()
could rebroadcast NETDEV_UNREGISTER event until all refs are
gone.
We have to add an additional check to avoid this corner case.
For netdev_wait_allrefs() dev->reg_state is NETREG_UNREGISTERED,
for dev_change_net_namespace(), dev->reg_state is
NETREG_REGISTERED. So check for dev->reg_state != NETREG_UNREGISTERED.
Fixes: 242d3a49a2 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf")
Reported-by: jeffy <jeffy.chen@rock-chips.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit ("net/phy: micrel: Add workaround for bad autoneg") fixes an
autoneg failure case by resetting the hardware. This turns off
intterupts. Things will work themselves out if the phy polls, as it will
figure out it's state during a poll. However if the phy uses only
intterupts, the phy will stall, since interrupts are off. This patch
fixes the issue by calling config_intr after resetting the phy.
Fixes: d2fd719bcb ("net/phy: micrel: Add workaround for bad autoneg ")
Signed-off-by: Zach Brown <zach.brown@ni.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TF is handled a bit differently for syscall and sysret, compared
to the other instructions: TF is checked after the instruction completes,
so that the OS can disable #DB at a syscall by adding TF to FMASK.
When the sysret is executed the #DB is taken "as if" the syscall insn
just completed.
KVM emulates syscall so that it can trap 32-bit syscall on Intel processors.
Fix the behavior, otherwise you could get #DB on a user stack which is not
nice. This does not affect Linux guests, as they use an IST or task gate
for #DB.
This fixes CVE-2017-7518.
Cc: stable@vger.kernel.org
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
NPU2 requires an extra explicit flush to an active GPU PID when
sending address translation shoot downs (ATSDs) to reliably flush the
GPU TLB. This patch adds just such a flush at the end of each sequence
of ATSDs.
We can safely use PID 0 which is always reserved and active on the
GPU. PID 0 is only used for init_mm which will never be a user mm on
the GPU. To enforce this we add a check in pnv_npu2_init_context()
just in case someone tries to use PID 0 on the GPU.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
[mpe: Use true/false for bool literals]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For real-space designation asces the asce origin part is only a token.
The asce token origin must not be used to generate an effective
address for storage references. This however is erroneously done
within kvm_s390_shadow_tables().
Furthermore within the same function the wrong parts of virtual
addresses are used to generate a corresponding real address
(e.g. the region second index is used as region first index).
Both of the above can result in incorrect address translations. Only
for real space designations with a token origin of zero and addresses
below one megabyte the translation was correct.
Furthermore replace a "!asce.r" statement with a "!*fake" statement to
make it more obvious that a specific condition has nothing to do with
the architecture, but with the fake handling of real space designations.
Fixes: 3218f7094b ("s390/mm: support real-space for gmap shadows")
Cc: David Hildenbrand <david@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Current DTLB load/store miss events (0x608/0x649) only counts 4K,2M and
4M page size.
Need to extend the events to support any page size (4K/2M/4M/1G).
The complete DTLB load/store miss events are:
DTLB_LOAD_MISSES.WALK_COMPLETED 0xe08
DTLB_STORE_MISSES.WALK_COMPLETED 0xe49
Signed-off-by: Kan Liang <Kan.liang@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/20170619142609.11058-1-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The i2c-imx driver incorrectly uses readb()/writeb() to read and
write to the appropriate registers when performing a repeated start.
The appropriate imx_i2c_read_reg()/imx_i2c_write_reg() functions
should be used instead. Performing a repeated start results in
a kernel panic. The platform is imx.
Signed-off-by: Michail G Etairidis <m.etairidis@beck-ipc.com>
Fixes: ce1a78840f ("i2c: imx: add DMA support for freescale i2c driver")
Fixes: 054b62d9f2 ("i2c: imx: fix the i2c bus hang issue when do repeat restart")
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
IP6CB(skb)->nhoff is the offset of the nexthdr field in an IPv6
header, unless there are extension headers present, in which case
nhoff points to the nexthdr field of the last extension header.
In non-GRO code path, nhoff is set by ipv6_rcv before any XFRM code
is executed. Conversely, in GRO code path (when esp6_offload is loaded),
nhoff is not set. The following functions fail to read the correct value
and eventually the packet is dropped:
xfrm6_transport_finish
xfrm6_tunnel_input
xfrm6_rcv_tnl
Set nhoff to the proper offset of nexthdr in esp6_gro_receive.
Fixes: 7785bba299 ("esp: Add a software GRO codepath")
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
IPv6 payload length indicates the size of the payload, including any
extension headers.
In xfrm6_transport_finish, ipv6_hdr(skb)->payload_len is set to the
payload size only, regardless of the presence of any extension headers.
After ESP GRO transport mode decapsulation, ipv6_rcv trims the packet
according to the wrong payload_len, thus corrupting the packet.
Set payload_len to account for extension headers as well.
Fixes: 7785bba299 ("esp: Add a software GRO codepath")
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Pull block fixes from Jens Axboe:
"This contains a set of fixes for xen-blkback by way of Konrad, and a
performance regression fix for blk-mq for shared tags.
The latter could account for as much as a 50x reduction in
performance, with the test case from the user with 500 name spaces. A
more realistic setup on my end with 32 drives showed a 3.5x drop. The
fix has been thoroughly tested before being committed"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: fix performance regression with shared tags
xen-blkback: don't leak stack data via response ring
xen/blkback: don't use xen_blkif_get() in xen-blkback kthread
xen/blkback: don't free be structure too early
xen/blkback: fix disconnect while I/Os in flight
bmap returns a dumb LBA address but not the block device that goes with
that LBA. Swapfiles don't care about this and will blindly assume that
the data volume is the correct blockdev, which is totally bogus for
files on the rt subvolume. This results in the swap code doing IOs to
arbitrary locations on the data device(!) if the passed in mapping is a
realtime file, so just turn off bmap for rt files.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Since commit fcc8487d47 ("uapi: export all headers under uapi
directories") fakechroot make bindeb-pkg fails, mismatching files for
directories:
touch: cannot touch 'usr/include/video/uvesafb.h/.install': Not a
directory
This due to a bug in fakechroot:
when using the function $(wildcard $(srcdir)/*/.) in a makefile, under a
fakechroot environment, not only directories but also files are
returned.
To circumvent that, we are using the functions:
$(sort $(dir $(wildcard $(srcdir)/*/))))
Fixes: fcc8487d47 ("uapi: export all headers under uapi directories")
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit f406270bf7 ("ACPI / scan: Set the visited flag for all
enumerated devices") caused that two group of special SPI or I2C
devices do not enumerate. SPI and I2C devices are expected to be
enumerated by the SPI and I2C subsystems but change caused that
acpi_bus_attach() marks those devices with acpi_device_set_enumerated().
First group of devices are matched using Device Tree compatible property
with special _HID "PRP0001". Those devices have matched scan handler,
acpi_scan_attach_handler() retuns 1 and acpi_bus_attach() marks them
with acpi_device_set_enumerated().
Second group of devices without valid _HID such as "LNXVIDEO" have
device->pnp.type.platform_id set to zero and change again marks them
with acpi_device_set_enumerated().
Fix this by flagging the SPI and I2C devices during struct acpi_device
object initialization time and let the code in acpi_bus_attach() to go
through the device_attach() and acpi_default_enumeration() path for all
SPI and I2C devices.
Fixes: f406270bf7 (ACPI / scan: Set the visited flag for all enumerated devices)
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.11+ <stable@vger.kernel.org> # 4.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull networking fixes from David Miller:
1) Fix refcounting wrt timers which hold onto inet6 address objects,
from Xin Long.
2) Fix an ancient bug in wireless wext ioctls, from Johannes Berg.
3) Firmware handling fixes in brcm80211 driver, from Arend Van Spriel.
4) Several mlx5 driver fixes (firmware readiness, timestamp cap
reporting, devlink command validity checking, tc offloading, etc.)
From Eli Cohen, Maor Dickman, Chris Mi, and Or Gerlitz.
5) Fix dst leak in IP/IP6 tunnels, from Haishuang Yan.
6) Fix dst refcount bug in decnet, from Wei Wang.
7) Netdev can be double freed in register_vlan_device(). Fix from Gao
Feng.
8) Don't allow object to be destroyed while it is being dumped in SCTP,
from Xin Long.
9) Fix dpaa_eth build when modular, from Madalin Bucur.
10) Fix throw route leaks, from Serhey Popovych.
11) IFLA_GROUP missing from if_nlmsg_size() and ifla_policy[] table,
also from Serhey Popovych.
12) Fix premature TX SKB free in stmmac, from Niklas Cassel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
igmp: add a missing spin_lock_init()
net: stmmac: free an skb first when there are no longer any descriptors using it
sfc: remove duplicate up_write on VF filter_sem
rtnetlink: add IFLA_GROUP to ifla_policy
ipv6: Do not leak throw route references
dt-bindings: net: sms911x: Add missing optional VDD regulators
dpaa_eth: reuse the dma_ops provided by the FMan MAC device
fsl/fman: propagate dma_ops
net/core: remove explicit do_softirq() from busy_poll_stop()
fib_rules: Resolve goto rules target on delete
sctp: ensure ep is not destroyed before doing the dump
net/hns:bugfix of ethtool -t phy self_test
net: 8021q: Fix one possible panic caused by BUG_ON in free_netdev
cxgb4: notify uP to route ctrlq compl to rdma rspq
ip6_tunnel: Correct tos value in collect_md mode
decnet: always not take dst->__refcnt when inserting dst into hash table
ip6_tunnel: fix potential issue in __ip6_tnl_rcv
ip_tunnel: fix potential issue in ip_tunnel_rcv
brcmfmac: fix uninitialized warning in brcmf_usb_probe_phase2()
net/mlx5e: Avoid doing a cleanup call if the profile doesn't have it
...
- Make the AMD driver use a regular interrupt rather than a chained one,
so the system does not lock up.
- Fix a function call error deep inside the STM32 driver.
-----BEGIN PGP SIGNATURE-----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=2zx1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull more pin control fixes from Linus Walleij:
"Some late arriving fixes. I should have sent earlier, just swamped
with work as usual. Thomas patch makes AMD systems usable despite
firmware bugs so it is fairly important.
- Make the AMD driver use a regular interrupt rather than a chained
one, so the system does not lock up.
- Fix a function call error deep inside the STM32 driver"
* tag 'pinctrl-v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: stm32: Fix bad function call
pinctrl/amd: Use regular interrupt instead of chained
Pull HID fixes from Jiri Kosina:
- revert of a commit to magicmouse driver that regressess certain
devices, from Daniel Stone
- quirk for a specific Dell mouse, from Sebastian Parschauer
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: magicmouse: Set multi-touch keybits for Magic Mouse"
HID: Add quirk for Dell PIXART OEM mouse
Pull livepatching fix from Jiri Kosina:
"Fix the way how livepatches are being stacked with respect to RCU,
from Petr Mladek"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Fix stacking of patches with respect to RCU
Pull more ufs fixes from Al Viro:
"More UFS fixes, unfortunately including build regression fix for the
64-bit s_dsize commit. Fixed in this pile:
- trivial bug in signedness of 32bit timestamps on ufs1
- ESTALE instead of ufs_error() when doing open-by-fhandle on
something deleted
- build regression on 32bit in ufs_new_fragments() - calculating that
many percents of u64 pulls libgcc stuff on some of those. Mea
culpa.
- fix hysteresis loop broken by typo in 2.4.14.7 (right next to the
location of previous bug).
- fix the insane limits of said hysteresis loop on filesystems with
very low percentage of reserved blocks. If it's 5% or less, just
use the OPTSPACE policy.
- calculate those limits once and mount time.
This tree does pass xfstests clean (both ufs1 and ufs2) and it _does_
survive cross-builds.
Again, my apologies for missing that, especially since I have noticed
a related percentage-of-64bit issue in earlier patches (when dealing
with amount of reserved blocks). Self-LART applied..."
* 'ufs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs: fix the logics for tail relocation
ufs_iget(): fail with -ESTALE on deleted inode
fix signedness of timestamps on ufs1
Fix expand_upwards() on architectures with an upward-growing stack (parisc,
metag and partly IA-64) to allow the stack to reliably grow exactly up to
the address space limit given by TASK_SIZE.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trinity gets kernel BUG at mm/mmap.c:1963! in about 3 minutes of
mmap testing. That's the VM_BUG_ON(gap_end < gap_start) at the
end of unmapped_area_topdown(). Linus points out how MAP_FIXED
(which does not have to respect our stack guard gap intentions)
could result in gap_end below gap_start there. Fix that, and
the similar case in its alternative, unmapped_area().
Cc: stable@vger.kernel.org
Fixes: 1be7107fbe ("mm: larger stack guard gap, between vmas")
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Debugged-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we have shared tags enabled, then every IO completion will trigger
a full loop of every queue belonging to a tag set, and every hardware
queue for each of those queues, even if nothing needs to be done.
This causes a massive performance regression if you have a lot of
shared devices.
Instead of doing this huge full scan on every IO, add an atomic
counter to the main queue that tracks how many hardware queues have
been marked as needing a restart. With that, we can avoid looking for
restartable queues, if we don't have to.
Max reports that this restores performance. Before this patch, 4K
IOPS was limited to 22-23K IOPS. With the patch, we are running at
950-970K IOPS.
Fixes: 6d8c6c0f97 ("blk-mq: Restart a single queue if tag sets are shared")
Reported-by: Max Gurtovoy <maxg@mellanox.com>
Tested-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If only a subset of the devices associated with multiple regions support
a given special operation (eg. DISCARD) then the dec_count() that is
used to set error for the region must increment the io->count.
Otherwise, when the dec_count() is called it can cause the dm-io
caller's bio to be completed multiple times. As was reported against
the dm-mirror target that had mirror legs with a mix of discard
capabilities.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=196077
Reported-by: Zhang Yi <yizhan@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use spin_lock_irqsave and spin_unlock_irqrestore rather than
spin_{lock,unlock}_irq in submit_flush_bio().
Otherwise lockdep issues the following warning:
DEBUG_LOCKS_WARN_ON(current->hardirq_context)
WARNING: CPU: 1 PID: 0 at kernel/locking/lockdep.c:2748 trace_hardirqs_on_caller+0x107/0x180
Reported-by: Ondrej Kozina <okozina@redhat.com>
Tested-by: Ondrej Kozina <okozina@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
If the event for which an AUX area is about to be allocated, does
not support setting up an AUX area, rb_alloc_aux() return -ENOTSUPP.
This error condition is being returned unfiltered to the user space,
and, for example, the perf tools fails with:
failed to mmap with 524 (INTERNAL ERROR: strerror_r(524, 0x3fff497a1c8, 512)=22)
This error can be easily seen with "perf record -m 128,256 -e cpu-clock".
The 524 error code maps to -ENOTSUPP (in rb_alloc_aux()). The -ENOTSUPP
error code shall be only used within the kernel. So the correct error
code would then be -EOPNOTSUPP.
With this commit, the perf tool then reports:
failed to mmap with 95 (Operation not supported)
which is more clear.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pu Hou <bjhoupu@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Cc: acme@kernel.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/1497954399-6355-1-git-send-email-brueckner@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
