AFAICT, nobody is using ft_ordered(), and it causes a build warning
to be generated. This patch cleans that up by removing the function
and the commented-out code that calls it.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, spu_create with an invalid neighbo(u)r will return -ENOSYS,
not -EBADF, but only when spufs.o is built as a module.
This change adds the appropriate errno, making the behaviour the same
as the built-in case.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My "slices" address space management code that was added in the 2.6.22
implementation of get_unmapped_area() doesn't properly check that the
size is a multiple of the requested page size. This allows userland to
create VMAs that aren't a multiple of the huge page size with hugetlbfs
(since hugetlbfs entirely relies on get_unmapped_area() to do that
checking) which leads to a kernel BUG() when such areas are torn down.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc has a couple of bugs in the usage of dma_masks that tend to
break when drivers explicitly try to set a 32-bit mask for example.
First, the code that generates the pci devices from the OF device-tree
doesn't initialize the mask properly, then our implementation of
set_dma_mask() was trying to validate the -previous- mask value, not the
one passed in as an argument.
This fixes these problems.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 3baee95595.
That commit was a mistake from the start; I added mdio type to the
bus scan list early on in my ucc_geth migrate to phylib development,
which is just pure wrong (the ucc_geth_mii driver creates the mii
bus and the PHY layer handles PHY enumeration without translation).
This follows on from commit 77926826f3:
Revert "[POWERPC] Don't complain if size-cells == 0 in prom_parse()"
which was basically trying to hide a symptom of the original mistake
this revert fixes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the Kconfig message that indicates the PS3 platform support is
incomplete.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the PS3 storage probe logic to properly find device regions on cold
startup.
o Change the storage probe event mask from notify_device_ready
to notify_region_update.
o Improve the storage probe error handling.
o Change ps3_storage_wait_for_device() to use a temporary variable to hold
the buffer address.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves affinity initialization code from spu_base.c to a
new spu_management_of_ops function (init_affinity), which is empty
in the case of PS3. This fixes a linking problem that was happening
when compiling for PS3.
Also, some small code style changes were made.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were getting a duplicate entry in the SLB shadow buffer in
slb_flush_and_rebolt() if the kernel stack was in the same segment
as PAGE_OFFSET, which on POWER6 causes the hypervisor to terminate
the partition with an error. This fixes it.
Also we were not creating an SLB entry (or an SLB shadow buffer
entry) for the kernel stack on secondary CPUs when starting the
CPU. This isn't a major problem, since an appropriate entry will
be created on demand, but this fixes that also for consistency.
Signed-off-by: Paul Mackerras <paulus@samba.org>
On a machine with hardware 64kB pages and a kernel configured for a
64kB base page size, we need to change the vmalloc segment from 64kB
pages to 4kB pages if some driver creates a non-cacheable mapping in
the vmalloc area. However, we never updated with SLB shadow buffer.
This fixes it. Thanks to paulus for finding this.
Also added some write barriers to ensure the shadow buffer contents
are always consistent.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
...by using the pci_get API instead of the deprecated old stuff.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some new machines use the "ibm,dynamic-reconfiguration-memory" property
to provide memory layout information, rather than via memory nodes.
There is a bug in the code to parse this property for start addresses
over 4GB; we store the start address in an unsigned int, which means
we throw away the high bits and add apparently duplicate regions.
This results in a BUG() in free_bootmem_core(). This fixes it by
using an unsigned long instead.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In smp_call_function_map(), num_cpus is set to the number of online
CPUs minus one. However, if the CPU mask does not include all CPUs
(except the one we're running on), the routine will hang in the first
while() loop until the 8 second timeout occurs.
The num_cpus should be set to the number of CPUs specified in the mask
passed into the routine, after we've made any modifications to the
mask. With this change, we can also get rid of the call to
cpus_empty() and avoid adding another pass through the bitmask.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x605d4): Section mismatch: reference to
.init.text:.__alloc_bootmem (between '.prealloc' and '.ps3_power_save')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes affinity reference point placement, which was not being
done in some situations, after the introduction of node_allowed() calls.
The previously used parameter, 'ctx', is just the iterator of the
previous list_for_each_entry_reverse loop, and its value might be
invalid at the end of the loop. Also, the right context to seek
for information when defining the reference ctx location
_is_ the reference ctx.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code for mapping special 4k pages on kernels using a 64kB base
page size was missing the code for doing the RPN (real page number)
manipulation when inserting the hardware PTE in the secondary hash
bucket. It needs the same code as has already been added to the
code that inserts the HPTE in the primary hash bucket. This adds it.
Spotted by Ben Herrenschmidt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (28 commits)
[WATCHDOG] Fix pcwd_init_module crash
[WATCHDOG] ICH9 support for iTCO_wdt
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt - add all LPC bridges
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt
[WATCHDOG] omap_wdt.c - default error for IOCTL is -ENOTTY
[WATCHDOG] Return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Rework the timeout register manipulation
[WATCHDOG] mv64x60_wdt: disable watchdog timer when driver is probed
[WATCHDOG] mv64x60_wdt: Support the WDIOF_MAGICCLOSE feature
[WATCHDOG] mv64x60_wdt: Add a module parameter to change nowayout setting
[WATCHDOG] mv64x60_wdt: Add WDIOC_SETOPTIONS ioctl support
[WATCHDOG] mv64x60_wdt: Support for WDIOC_SETTIMEOUT ioctl
[WATCHDOG] mv64x60_wdt: Fix WDIOC_GETTIMEOUT return value
[WATCHDOG] mv64x60_wdt: Check return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Add arch/powerpc platform support
[WATCHDOG] mv64x60_wdt: Get register address from platform data
[WATCHDOG] mv64x60_wdt: set up platform_device in platform code
[WATCHDOG] ensure mouse and keyboard ignored in w83627hf_wdt
[WATCHDOG] s3c2410_wdt: fixup after arch include moves
[WATCHDOG] git-watchdog-typo
...
Remove unused TIF_NOTIFY_RESUME flag for all processor architectures. The
flag was not used excecpt on IA-64 where the patch replaces it with
TIF_PERFMON_WORK.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace CONFIG_SOFTWARE_SUSPEND with CONFIG_HIBERNATION to avoid
confusion (among other things, with CONFIG_SUSPEND introduced in the
next patch).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we calculate the first timeslice for every context
incorrectly - alloc_spu_context calls spu_set_timeslice before we set
ctx->prio so we always calculate the longest possible timeslice for the
lowest possible priority.
This patch makes sure to update the schedule-related fields before
calculating the timeslice and also makes sure we update the timeslice for
a non-running context when entering spu_run so a priority change affects
the context as soon as possible.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently initialize cbe_spu_info[].spus in both init_spu_base and
spu_sched_init. The initialise in spu_sched_init clears the SPU list,
so we end up with no physical SPUs. Because of this, the spu_run
syscall will block forever.
This change removes the unnecessary initialization in spu_sched_init.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Maple platform has ISA IOs but didn't call the new functions to
actually map those, thus crashing when trying to access the nvram.
This fixes Maple and JS2x using SLOF.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch uses the newly added functions for testing if an address is
an ISA or PCI IO port to properly unmap things in pci_iounmap that
aren't such ports. Without that, drivers using the iomap API will never
actually unmap resources, which on IBM server machines will prevent
hot-unplug of the corresponding HW adapters.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a function that tells you if a given kernel virtual address
is hitting a PCI or ISA IO port permanent mapping or not. This is to
be used in the next patch to fix iomap APIs to properly unmap things.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As of 2.6.22 the kernel doesn't recognize the i8042 keyboard/mouse
controller on the PegasosPPC. This is because of a feature/bug in the
OF device tree: the "device_type" attribute is an empty string instead
of "8042" as the kernel expects. This adds a secondary detection
which looks for a device whose *name* is "8042" if there is no device
whose *type* is "8042".
Signed-off-by: Alan Curry <pacman@world.std.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x4f568): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.setup_hvlpevent_queue' and '.process_hvlpevents')
setup_hvlpevent_queue is only called from __init code so make it __init
as well.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x8124): Section mismatch: reference to .init.text:.iSeries_early_setup (between '.__start_initialization_iSeries' and '.__mmu_off')
WARNING: vmlinux.o(.text+0x8128): Section mismatch: reference to .init.text:.early_setup (between '.__start_initialization_iSeries' and '.__mmu_off')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the RTC on linkstation ppc machines again, and updates the
device tree: add rtc nodes on i2c, remove bogus 0-size cache-line
declarations, rename interrupt-controller nodes, remove erroneous
interrupt-parent line, accidentally introduced by a recent patch.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Scan the device tree for i2c devices, check their "compatible" property
against a hard-coded table, and, if found, register with i2c boardinfo.
This provides the infrastructure needed to find i2c devices in the
device tree and register them with the i2c subsystem.
This and the following commit let the linkstation work with the new i2c
API and thus fix a regression.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a possible infinite loop when the unsigned long counter "i"
is used in lmb_add_region() in the following for loop:
for (i = rgn->cnt-1; i >= 0; i--)
by making the loop counter "i" be signed.
Signed-off-by: Manish Ahuja <ahuja@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In a show_regs() message The DEAR and ESR were reported as
DAR and DSISR which only exist on classic parts.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
BootX text code is only supported on systems with real OF at this point
which is PPC_OF && PPC_MULTIPLATFORM.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add global-utilities node with has-rstcr on MPC8544 DS and MPC8568 MDS
boards so they are able to reset properly.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix mpc7448hpc2 tsi108 device_type bug.
Wrong device type will break the board startup.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fixed the following warnings:
WARNING: vmlinux.o(.text+0x2934): Section mismatch: reference to .init.text:__alloc_bootmem (between 'irq_alloc_host' and 'irq_set_default_host')
WARNING: vmlinux.o(.text+0xb2aa): Section mismatch: reference to .init.data:boot_command_line (between 'register_early_udbg_console' and 'udbg_printf')
WARNING: vmlinux.o(.text+0xb2b2): Section mismatch: reference to .init.data:boot_command_line (between 'register_early_udbg_console' and 'udbg_printf')
WARNING: vmlinux.o(.text+0xe354): Section mismatch: reference to .init.text:__alloc_bootmem (between 'pcibios_alloc_controller' and 'pci_domain_nr')
WARNING: vmlinux.o(.text+0x12768): Section mismatch: reference to .init.text:update_bridge_resource (between 'quirk_fsl_pcie_transparent' and 'indirect_read_config')
WARNING: vmlinux.o(.text+0x127a8): Section mismatch: reference to .init.text:update_bridge_resource (between 'quirk_fsl_pcie_transparent' and 'indirect_read_config')
WARNING: vmlinux.o(.text+0x17566c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bus_parented')
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8544 dts needed to set the new phy-connection-type to rgmii-id
for the Vitesse PHY on the board to work properly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale PCI PHBs actual report back values in the BAR registers
this causes issues in that we try to allocate resources for them
and will get error messages like the following on MPC8544 DS:
PCI: Failed to allocate mem resource #1:80000000@0 for 0000:00:00.0
To address this if we are class PCI_CLASS_PROCESSOR_POWERPC, a normal
header type, and the PHB we clear out all the resources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit fd6e9d3945.
Having #size-cells == 0 in a node indicates that things under the
node aren't directly accessible, and therefore we shouldn't try to
translate addresses for devices under the node into CPU physical
addresses.
Some drivers, such as the nvram driver for powermacs, rely on
of_address_to_resource failing if they are called for a node
representing a device whose resources aren't directly accessible
by the CPU. These drivers were broken by commit fd6e9d39,
resulting in the "Lombard" powerbook hanging early in the boot
process.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We didn't actually propogate the flag we pass into setup_indirect_pci()
to set indirect_type and thus were getting the wrong endianness if
PPC_INDIRECT_TYPE_BIG_ENDIAN was set.
Also, we need to or in additional flags rather than just doing a
direct assignment.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for arch/powerpc, specifically for the prpmc2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
spufs.h now has two enums for the sched_flags leading to identical
values for SPU_SCHED_WAS_ACTIVE and SPU_SCHED_NOTIFY_ACTIVE. Merge
them into a single enum as they were in the IBM development tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added the MPC85xx PCI device IDs that we need for the quirks we have.
Also, fixed the MPC8567E, MPC8567 device IDs which had the wrong value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also add 8641/8641D device IDs as well.
All of which already exist or have been submitted to
The Linux PCI ID Repository at:
http://pci-ids.ucw.cz/
CC-to: pci-ids@ucw.cz
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added the P2P bridge present on the Arcadia base board and moved the VIA
Southbridge behind the bridge to reflect its actual position in the bus
organization. Added the RTC that's in the VIA Southbridge and expanded
the ranges array for the SOC node to allow proper address translation of
the RTC registers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Setting the host bridge @8000 as primary. Also fixing a bug in
setting the USB interrupt numbers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupts of an E100 card inserted in PCI slot 4 may be on at bootup.
The resulting interrupt flood interacts with the 8259 cascade handler and
prevents proper boot up. There is a quirk for the E100 that will disable
the E100's interrupts but to use it, the 8259 cascade hookup must be
delayed until after the quirk has run. This patch delays the 8259 cascade
hookup by registering a device_initcall() which runs after the PCI quirk
for the E100.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current 85xxCDS restart code fails to reset the PCI bus which can
lead to odd behavior after the restart. This patch uses the VIA Super
Southbridge to perform a PCI reset which will reset the entire system.
NOTE: Since the VIA chip is behind a PCI-to-PCI bridge which can be
disabled with a switch setting, it may not be possible to perform the
PCI bus reset. In this case, the code defaults to the previous restart
mechanism.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale MPC8555CDS and MPC8548CDS reference hardware has a legacy
8259 interrupt controller pair contained within a VIA VT82C686B Southbridge
on the main carrier board. The processor complex plugs into the carrier
card using a PCI slot which limits the available interrupts to the
INTA-INTD PCI interrupts. The output of the 8259 cascade pair is routed
through a gate array and connected to the PCI INTA interrupt line.
The normal interrupt chaining hook (set_irq_chained_handler) does
not allow sharing of the chained interrupt which prevents the
use of PCI INTA by PCI devices. This patch allows the 8259 cascade
pair to share their interrupt line with PCI devices.
NOTE: The addition of the .end routine for the MPIC is not strictly
necessary for this patch. It's there so this code will run from within
the threaded interrupt context used by the Real Time patch.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some set of 85xx platforms have PCI-X controllers. The old arch/ppc
code setup these controllers and we haven't moved it over to arch/powerpc.
We use the PCI-X Capabilties to know if we are in PCI-X mode instead
of the Global Utilities PORDEVSR.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the Freescale PCIe PHBs Not all firmwares setup the virtual P2P
bridge registers properly. Make sure they get setup based on what
the struct pci_controller got from the device tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need the ability to set P2P bridge registers to properly setup the virtual
P2P bridges that exist in PCIe controllers for some of the embedded setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian. This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't use setup_indirect_pci_nomap in arch/powerpc and it appears
the users that needed it from arch/ppc are now using setup_indirect_pci.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The newer Arcadia boards for CDS have an FPGA that shows up on PCI
however isn't a real PCI device. Add a quirk to just ignore the
FPGA.
This is based on the following patch from Andy & York:
http://ozlabs.org/pipermail/linuxppc-dev/2007-February/032042.html
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the 85xx/86xx PCIe controllers if there is no device connected to the
PHB we will still allocate a pci_bus for downstream bus of the virtual
P2P bridge. However the resources allocated to the downstream bus are not
correct and so we just mimic the resources from the upstream pci_bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch the 85xx platform over to using the FSL generic PCI code. This
gets ups PCIe support in addition to base PCI support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the 83xx & 85xx device tree PCI related compartible property.
Used the following compatible properties:
PCI "fsl,mpc8349-pci"
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 8548 CDS PCI express controller node and PCI-X device node. The current
dts file is suitable for 8548 Rev 2.0 board with Arcadia 3.1.
This kind of board combination is the most popular.
Used the following compatible properties:
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the PCI capabilities to determine if we are PCIe PHB. Also use
PPC_INDIRECT_TYPE_NO_PCIE_LINK since the Freescale PCIe controllers
will lock the system if they don't have link and you try to do a config
access to anything but the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added PPC_INDIRECT_TYPE_NO_PCIE_LINK flag to the indirect pci handling
code to ensure that we don't talk to any device other than the PHB
if we don't have PCIe link. Some controllers will lockup if they try
to do a config cycle to any device on the bus except the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added early_find_capability that wraps pci_bus_find_capability and uses
fake_pci_bus() to allow us to call it before we've fully setup the
pci_controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rewrite the Freescale PCI code to support PCI on 83xx/85xx/86xx and
PCIe on 85xx/86xx.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move
arch/powerpc/platforms/86xx/pci.c -> arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pcie.h -> arch/powerpc/sysdev/fsl_pci.h
as the base to unify 83xx/85xx/86xx pci and pcie.
Add CONFIG_FSL_PCI to build fsl_pci.c for Freescale pci and pcie option.
The code still works for 86xx platforms.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Clean up duplicate includes in drivers/macintosh/
[POWERPC] Quiet section mismatch warning on pcibios_setup
[POWERPC] init and exit markings for hvc_iseries
[POWERPC] Quiet section mismatch in hvc_rtas.c
[POWERPC] Constify of_platform_driver match_table
[POWERPC] hvcs: Make some things static and const
[POWERPC] Constify of_platform_driver name
[POWERPC] MPIC protected sources
[POWERPC] of_detach_node()'s device node argument cannot be const
[POWERPC] Fix ARCH=ppc builds
[POWERPC] mv64x60: Use mutex instead of semaphore
[POWERPC] Allow smp_call_function_single() to current cpu
[POWERPC] Allow exec faults on readable areas on classic 32-bit PowerPC
[POWERPC] Fix future firmware feature fixups function failure
[POWERPC] fix showing xmon help
[POWERPC] Make xmon_write accept a const buffer
[POWERPC] Fix misspelled "CONFIG_CHECK_CACHE_COHERENCY" Kconfig option.
[POWERPC] cell: CONFIG_SPE_BASE is a typo
Fix a mismerge in commit 8b6f50ef1d:
"spufs: make signal-notification files readonly for NOSCHED contexts",
where structs got duplicated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: vmlinux.o(.text+0x1cefcc): Section mismatch: reference to .init.text:.pcibios_setup (between '.pci_setup' and '.pci_init')
pci_setup() is marked __devinit and calls pcibios_setup.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some HW platforms, such as the new cell blades, requires some MPIC sources
to be left alone by the operating system. This implements support for
a "protected-sources" property in the mpic controller node containing a list
of source numbers to be protected against operating system interference.
For those interested in the gory details, the MPIC on the southbridge of
those blades has some of the processor outputs routed to the cell, and
at least one routed as a GPIO to the service processor. It will be used
in the GA product for routing some of the southbridge error interrupts
to the service processor which implements some of the RAS stuff, such
as checkstopping when fatal errors occurs before they can propagate.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
...since it modifies it (when it sets the OF_DETACHED flag).
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes the requirement for callers to get_cpu() to check in simple
cases. i386 and x86_64 already received a similar treatment.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Classic 32-bit PowerPC CPUs, and the early 64-bit PowerPC CPUs, don't
provide a way to prevent execution from readable pages, that is, the
MMU doesn't distinguish between data reads and instruction reads,
although a different exception is taken for faults in data accesses
and instruction accesses.
Commit 9ba4ace39f, in the course of
fixing another bug, added a check that meant that a page fault due
to an instruction access would fail if the vma did not have the
VM_EXEC flag set. This gives an inconsistent enforcement on these
CPUs of the no-execute status of the vma (since reading from the page
is sufficient to allow subsequent execution from it), and causes old
versions of ppc32 glibc (2.2 and earlier) to fail, since they rely
on executing the word before the GOT but don't have it marked
executable.
This fixes the problem by allowing execution from readable (or writable)
areas on CPUs which do not provide separate control over data and
instruction reads.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Move firmware feature initialisation from pSeries_init_early to the
earlier pSeries_probe_hypertas so they are initialised before firmware
feature fixups are applied.
Currently firmware feature sections are only used for iSeries which
initialises the these features much earlier. This is a bug in waiting
on pSeries.
Also adds some whitespace fixups.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In some configuration, xmon help string is larger than xmon_printf
buffer. We need not to use printf. This patch adds xmon_puts and
change to use it to show help string.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because xmon_write doesn't change the buffer, we should add 'const'
qualifier to the argument which points it.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The config symbol for SPE support is called CONFIG_SPU_BASE, not
CONFIG_SPE_BASE.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reading from the signal{1,2} files requires a spu_acquire_saved, so make these
files write-only for contexts created with SPU_CREATE_NOSCHED.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PS3 bootwrapper files use instructions only available on 64-bit CPUs.
Add the code generation directive '.machine "ppc64"' for toolchains
configured for 32-bit CPUs.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a FLASH ROM Storage Driver for the PS3:
- Implemented as a misc character device driver
- Uses a fixed 256 KiB buffer allocated from boot memory as the hypervisor
requires the writing of aligned 256 KiB blocks
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a BD/DVD/CD-ROM Storage Driver for the PS3:
- Implemented as a SCSI device driver
- Uses software scatter-gather with a 64 KiB bounce buffer as the hypervisor
doesn't support scatter-gather
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a Disk Storage Driver for the PS3:
- Implemented as a block device driver with a dynamic major
- Disk names (and partitions) are of the format ps3d%c(%u)
- Uses software scatter-gather with a 64 KiB bounce buffer as the hypervisor
doesn't support scatter-gather
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
allnoconfig results in this:
CC arch/powerpc/mm/tlb_32.o
In file included from include/asm/tlb.h:60,
from arch/powerpc/mm/tlb_32.c:30:
include/asm-generic/tlb.h: In function 'tlb_flush_mmu':
include/asm-generic/tlb.h:76: error: implicit declaration of function 'release_pages'
include/asm-generic/tlb.h: In function 'tlb_remove_page':
include/asm-generic/tlb.h:105: error: implicit declaration of function 'page_cache_release'
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This sorts out the various lists and related locks in the spu code.
In detail:
- the per-node free_spus and active_list are gone. Instead struct spu
gained an alloc_state member telling whether the spu is free or not
- the per-node spus array is now locked by a per-node mutex, which
takes over from the global spu_lock and the per-node active_mutex
- the spu_alloc* and spu_free function are gone as the state change is
now done inline in the spufs code. This allows some more sharing of
code for the affinity vs normal case and more efficient locking
- some little refactoring in the affinity code for this locking scheme
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
From: Maynard Johnson <mpjohn@us.ibm.com>
This patch updates the existing arch/powerpc/oprofile/op_model_cell.c
to add in the SPU profiling capabilities. In addition, a 'cell' subdirectory
was added to arch/powerpc/oprofile to hold Cell-specific SPU profiling code.
Exports spu_set_profile_private_kref and spu_get_profile_private_kref which
are used by OProfile to store private profile information in spufs data
structures.
Also incorporated several fixes from other patches (rrn). Check pointer
returned from kzalloc. Eliminated unnecessary cast. Better error
handling and cleanup in the related area. 64-bit unsigned long parameter
was being demoted to 32-bit unsigned int and eventually promoted back to
unsigned long.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
From: Maynard Johnson <mpjohn@us.ibm.com>
This patch adds to the capability of spu_switch_event_register so that
the caller is also notified of currently active SPU tasks.
Exports spu_switch_event_register and spu_switch_event_unregister so
that OProfile can get access to the notifications provided.
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Sort out the locking mess in spu_base and document the current rules.
As an added benefit spu_alloc* and spu_free don't block anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch links spus according to their physical position using
information provided by the firmware through a special vicinity
device-tree property. This property is present in current version
of Malta firmware.
Example of vicinity properties for a node in Malta:
Node: Vicinity property contains phandles of:
spe@0 [ spe@100000 , mic-tm@50a000 ]
spe@100000 [ spe@0 , spe@200000 ]
spe@200000 [ spe@100000 , spe@300000 ]
spe@300000 [ spe@200000 , bif0@512000 ]
spe@80000 [ spe@180000 , mic-tm@50a000 ]
spe@180000 [ spe@80000 , spe@280000 ]
spe@280000 [ spe@180000 , spe@380000 ]
spe@380000 [ spe@280000 , bif0@512000 ]
Only spe@* have a vicinity property (e.g., bif0@512000 and
mic-tm@50a000 do not have it).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch makes the scheduller honor affinity information for each
context being scheduled. If the context has no affinity information,
behaviour is unchanged. If there are affinity information, context is
schedulled to be run on the exact spu recommended by the affinity
placement algorithm.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch provides the spu affinity placement logic for the spufs scheduler.
Each time a gang is going to be scheduled, the placement of a reference
context is defined. The placement of all other contexts with affinity from
the gang is defined based on this reference context location and on a
precomputed displacement offset.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds support for additional flags at spu_create, which relate
to the establishment of affinity between contexts and contexts to memory.
A fourth, optional, parameter is supported. This parameter represent
a affinity neighbor of the context being created, and is used when defining
SPU-SPU affinity.
Affinity is represented as a doubly linked list of spu_contexts.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch allows the use of spu affinity on QS20, whose
original FW does not provide affinity information.
This is done through two hardcoded arrays, and by reading the reg
property from each spu.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds affinity data to each spu instance.
A doubly linked list is created, meant to connect the spus
in the physical order they are placed in the BE. SPUs
near to memory should be marked as having memory affinity.
Adjustments of the fields acording to FW properties is done
in separate patches, one for CPBW, one for Malta (patch for
Malta under testing).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
