Move and fixup all sysfs related bits to sysfs.c file.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Clean out dma_v2 and remove ioat2 calls since we are moving everything
to just ioat.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Changing the variable names for ioatdma_device to be consistently named
ioat_dma instead of device/dma in order to avoid confusion and distinct
from struct device. This will clearly indicate that it is an
ioatdma_device. This also make all the naming consistent that the dma
device is ioat_dma and all the channels are ioat_chan.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Kill the common ioatdma channel structure and everything that is not
dma_chan to be ioat_dma_chan. Since we don't have to worry about v1
and v2 ioatdma anymore this makes it much cleaner and obvious for
maintenance.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removal of support for ioatdma v2 device support.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cleaning up of ioat1 specific code as it is no longer supported
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removal of any devices that are ioatdma pre-3.0. This is the first step
in attempting to clean up the ioatdma driver and remove hw no longer
supported.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the allocation order is 16, then the u16 count will overflow and wrap
to zero when assigned the value 1 << 16.
Change the type of 'total_descs' to int, so that it is large enough to
store a value equal or greater than 1 << 16.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the allocation order is 16, then the u16 index will overflow and wrap
to zero instead of being equal or greater than 1 << 16. The loop
condition will always be true, and the loop will run until all the
memory resources are depleted.
Change the type of index 'i' to u32, so that it is large enough to store
a value equal or greater than 1 << 16.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The functions irq_irq_err and ipu_irq_fn are identical plus/minus the
comments. Remove one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The XDMAC also supports memset operations over discontiguous areas. Add the
necessary logic to support this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DMA will not stop when clearing enable bit till all transaction
is done. The bug is exposed in audio playback because ring DMA
chain never stop. Force hardware to stop with setting FORCE bit.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Align src and dst width to fix data alignment issue as
trailing single transaction that does not fill a full
burst require identical src/dst data width.
Burst length limitation can be addressed well too.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Most drivers need to set constraints on the buffer alignment for async tx
operations. However, even though it is documented, some drivers either use
a defined constant that is not matching what the alignment variable expects
(like DMA_BUSWIDTH_* constants) or fill the alignment in bytes instead of
power of two.
Add a new enum for these alignments that matches what the framework
expects, and convert the drivers to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
devm_ioremap_resource returns ERR_PTR on failure.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds DEV_TO_DEV support for i.MX SDMA driver to support data
transfer between two peripheral FIFOs.
The per_2_per script requires two peripheral addresses and two DMA
requests, and it need to check the src addr and dst addr is in the SPBA
bus space or in the AIPS bus space.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We had a regression due to reuse of descriptor so we have reverted that.
Rest are driver fixes
at_hdmac and at_xdmac for residue, trannfer width, and channel config
pl330 final fix for dma fails and overflow issue
xgene resouce map fix
mv_xor big endian op fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=X0jd
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.2-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"We had a regression due to reuse of descriptor so we have reverted
that.
The rest are driver fixes:
- at_hdmac and at_xdmac for residue, trannfer width, and channel config
- pl330 final fix for dma fails and overflow issue
- xgene resouce map fix
- mv_xor big endian op fix"
* tag 'dmaengine-fix-4.2-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
Revert "dmaengine: virt-dma: don't always free descriptor upon completion"
dmaengine: mv_xor: fix big endian operation in register mode
dmaengine: xgene-dma: Fix the resource map to handle overlapping
dmaengine: at_xdmac: fix transfer data width in at_xdmac_prep_slave_sg()
dmaengine: at_hdmac: fix residue computation
dmaengine: at_xdmac: fix bug about channel configuration
dmaengine: pl330: Really fix choppy sound because of wrong residue calculation
dmaengine: pl330: Fix overflow when reporting residue in memcpy
This reverts commit b9855f03d560d351e95301b9de0bc3cad3b31fe9.
The patch break existing DMA usage case. For example, audio SOC
dmaengine never release channel and cause virt-dma to cache too
much memory in descriptor to exhaust system memory.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 6f166312c6ea2 ("dmaengine: mv_xor: add support for a38x command
in descriptor mode") introduced the support for a feature that
appeared in Armada 38x: specifying the operation to be performed in a
per-descriptor basis rather than globally per channel.
However, when doing so, it changed the function mv_chan_set_mode() to
use:
if (IS_ENABLED(__BIG_ENDIAN))
instead of:
#if defined(__BIG_ENDIAN)
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler. Consequently, the commit broke support for big-endian,
as the XOR_DESCRIPTOR_SWAP flag was not set in the XOR channel
configuration register.
The primarily visible effect was some nasty warnings and failures
appearing during the self-test of the XOR unit:
[ 1.197368] mv_xor d0060900.xor: error on chan 0. intr cause 0x00000082
[ 1.197393] mv_xor d0060900.xor: config 0x00008440
[ 1.197410] mv_xor d0060900.xor: activation 0x00000000
[ 1.197427] mv_xor d0060900.xor: intr cause 0x00000082
[ 1.197443] mv_xor d0060900.xor: intr mask 0x000003f7
[ 1.197460] mv_xor d0060900.xor: error cause 0x00000000
[ 1.197477] mv_xor d0060900.xor: error addr 0x00000000
[ 1.197491] ------------[ cut here ]------------
[ 1.197513] WARNING: CPU: 0 PID: 1 at ../drivers/dma/mv_xor.c:664 mv_xor_interrupt_handler+0x14c/0x170()
See also:
http://storage.kernelci.org/next/next-20150617/arm-mvebu_v7_defconfig+CONFIG_CPU_BIG_ENDIAN=y/lab-khilman/boot-armada-xp-openblocks-ax3-4.txt
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 6f166312c6ea2 ("dmaengine: mv_xor: add support for a38x command in descriptor mode")
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is an overlap in dma ring cmd csr region due to sharing of ethernet
ring cmd csr region. This patch fix the resource overlapping by mapping
the entire dma ring cmd csr region.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the missing update of the transfer data width in
at_xdmac_prep_slave_sg().
Indeed, for each item in the scatter-gather list, we check whether the
transfer length is aligned with the data width provided by
dmaengine_slave_config(). If so, we directly use this data width for the
current part of the transfer we are preparing. Otherwise, the data width
is reduced to 8 bits (1 byte). Of course, the actual number of register
accesses must also be updated to match the new data width.
So one chunk was missing in the original patch (see Fixes tag below): the
number of register accesses was correctly set to (len >> fixed_dwidth) in
mbr_ubc but the real data width was not updated in mbr_cfg. Since mbr_cfg
may change for each part of the scatter-gather transfer this also explains
why the original patch used the Descriptor View 2 instead of the
Descriptor View 1.
Let's take the example of a DMA transfer to write 8bit data into an Atmel
USART with FIFOs. When FIFOs are enabled in the USART, its Transmit
Holding Register (THR) works in multidata mode, that is to say that up to
4 8bit data can be written into the THR in a single 32bit access and it is
still possible to write only one data with a 8bit access. To take
advantage of this new feature, the DMA driver was modified to allow
multiple dwidths when doing slave transfers.
For instance, when the total length is 22 bytes, the USART driver splits
the transfer into 2 parts:
First part: 20 bytes transferred through 5 32bit writes into THR
Second part: 2 bytes transferred though 2 8bit writes into THR
For the second part, the data width was first set to 4_BYTES by the USART
driver thanks to dmaengine_slave_config() then at_xdmac_prep_slave_sg()
reduces this data width to 1_BYTE because the 2 byte length is not aligned
with the original 4_BYTES data width. Since the data width is modified,
the actual number of writes into THR must be set accordingly.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 6d3a7d9e3ada ("dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers")
Cc: stable@vger.kernel.org #4.0 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As claimed by the programmer datasheet and confirmed by the IP designer,
the Block Transfer Size (BTSIZE) bitfield of the Channel x Control A
Register (CTRLAx) always refers to a number of Source Width (SRC_WIDTH)
transfers.
Both the SRC_WIDTH and BTSIZE bitfields can be extacted from the CTRLAx
register to compute the DMA residue. So the 'tx_width' field is useless
and can be removed from the struct at_desc.
Before this patch, atc_prep_slave_sg() was not consistent: BTSIZE was
correctly initialized according to the SRC_WIDTH but 'tx_width' was always
set to reg_width, which was incorrect for MEM_TO_DEV transfers. It led to
bad DMA residue when 'tx_width' != SRC_WIDTH.
Also the 'tx_width' field was mostly set only in the first and last
descriptors. Depending on the kind of DMA transfer, this field remained
uninitialized for intermediate descriptors. The accurate DMA residue was
computed only when the currently processed descriptor was the first or the
last of the chain. This algorithm was a little bit odd. An accurate DMA
residue can always be computed using the SRC_WIDTH and BTSIZE bitfields
in the CTRLAx register.
Finally, the test to check whether the currently processed descriptor is
the last of the chain was wrong: for cyclic transfer, last_desc->lli.dscr
is NOT equal to zero, since set_desc_eol() is never called, but logically
equal to first_desc->txd.phys. This bug has a side effect on the
drivers/tty/serial/atmel_serial.c driver, which uses cyclic DMA transfer
to receive data. Since the DMA residue was wrong each time the DMA
transfer reaches the second (and last) period of the transfer, no more
data were received by the USART driver till the cyclic DMA transfer loops
back to the first period.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Torsten Fleischer <torfl6749@gmail.com>
Tested-by: Jirí Prchal <jiri.prchal@aksignal.cz>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When using descriptor view 2 or higher, we don't write the configuration
into AT_XDMAC_CC register because this configuration will be fetch from
the descriptor. Unfortunately, the PROT bit is not updated with this
method, we have to do it manually before enabling the channel.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Intel integrated DMA (iDMA) 64-bit is a specific IP that is used as a part of
LPSS devices such as HSUART or SPI. The iDMA IP is attached for private
usage on each host controller independently.
While it has similarities with Synopsys DesignWare DMA, the following
distinctions doesn't allow to use the existing driver:
- 64-bit mode with corresponding changes in Hardware Linked List data structure
- many slight differences in the channel registers
Moreover this driver is based on the DMA virtual channels framework that helps
to make the driver cleaner and easy to understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The crossbar for eDMA works exactly the same way as sDMA, but sDMA
requires an offset of 1, while no offset is needed for eDMA.
Based on the patch from Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Switch to my kernel.org alias instead of a badly named gmail address,
which I rarely use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At device removal, tasklets are not disabled and irqs are still enabled, so
free the irq explicitly on device removal
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add ZTE ZX296702 dma controller support. Only
device tree probe is support currently.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
This is also a preparation for the removal of the 'irq' argument from
interrupt flow handlers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All hardware accesses are done under virtual channel lock. That's why specific
channel lock is excessive and can be removed safely. This has been tested on
Intel Medfield and Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dmaengine core assumes that async DMA devices will only be removed
when they not used anymore, or it assumes dma_async_device_unregister()
will only be called by dma driver exit routines. But this assumption is
not true for the IOAT driver, which calls dma_async_device_unregister()
from ioat_remove(). So current IOAT driver doesn't support device
hot-removal because it may cause system crash to hot-remove an inuse
IOAT device.
To support CPU socket hot-removal, all PCI devices, including IOAT
devices embedded in the socket, will be hot-removed. The idea solution
is to enhance the dmaengine core and IOAT driver to support hot-removal,
but that's too hard.
This patch implements a hack to disable IOAT devices under hotplug-capable
CPU socket so it won't break socket hot-removal.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This allows claiming of non-RAID channels as a private channel. This
prevents breakage of MDRAID using the IOATDMA channels via
async_tx but also allows agents such as NTB to claim channels
exclusively for its usages.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removing static analysis error:-
Possible null pointer dereference: xt
Because currently xt is dereferenced before NULL check,
Thus Use it after NULL Check.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
While at it, change the label 'err' to a more descriptive naming.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When pl330 driver was used during sound playback, after some time or
after a number of plays the sound became choppy or totally noisy. For
example on Odroid XU3 board the first four executions of aplay with
small WAVE worked fine, but fifth was unrecognizable with errors:
$ aplay /usr/share/sounds/alsa/Front_Right.wava
underrun!!! (at least 0.095 ms long)
Issue was caused by wrong residue reported by pl330 driver to
pcm_dmaengine for its cyclic dma transfers.
The pl330_tx_status(), residue reporting function, used a "last" flag in
a descriptor to indicate that there is no more data to send.
The pl330_tx_submit() iterated over descriptors trying to remove this
flag from them and then mark last descriptor as "last". However when
iterating it actually removed the flag not from descriptors but always
from last of it (and then reset it). Thus effectively once some
descriptor was marked as last, then it stayed like this forever causing
residue to be reported too low.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Fixes: aee4d1fac887 ("dmaengine: pl330: improve pl330_tx_status() function")
Cc: <stable@vger.kernel.org>
Reported-by: gabriel@unseen.is
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During memcpy operations the residue was always set to an u32 overflowed
value.
In pl330_tx_status() function number of currently transferred bytes was
subtracted from internal "bytes_requested" field. However this
"bytes_requested" was not initialized at start to length of memcpy
buffer so transferred bytes were subtracted from 0 causing overflow.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: aee4d1fac887 ("dmaengine: pl330: improve pl330_tx_status() function")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 3b62286d0ef7 ("dmaengine: Remove FSF mailing addresses") left Free
Software Foundation mailing address still in two files. Remove it now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Merge third patchbomb from Andrew Morton:
- the rest of MM
- scripts/gdb updates
- ipc/ updates
- lib/ updates
- MAINTAINERS updates
- various other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (67 commits)
genalloc: rename of_get_named_gen_pool() to of_gen_pool_get()
genalloc: rename dev_get_gen_pool() to gen_pool_get()
x86: opt into HAVE_COPY_THREAD_TLS, for both 32-bit and 64-bit
MAINTAINERS: add zpool
MAINTAINERS: BCACHE: Kent Overstreet has changed email address
MAINTAINERS: move Jens Osterkamp to CREDITS
MAINTAINERS: remove unused nbd.h pattern
MAINTAINERS: update brcm gpio filename pattern
MAINTAINERS: update brcm dts pattern
MAINTAINERS: update sound soc intel patterns
MAINTAINERS: remove website for paride
MAINTAINERS: update Emulex ocrdma email addresses
bcache: use kvfree() in various places
libcxgbi: use kvfree() in cxgbi_free_big_mem()
target: use kvfree() in session alloc and free
IB/ehca: use kvfree() in ipz_queue_{cd}tor()
drm/nouveau/gem: use kvfree() in u_free()
drm: use kvfree() in drm_free_large()
cxgb4: use kvfree() in t4_free_mem()
cxgb3: use kvfree() in cxgb_free_mem()
...
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVkgKHAAoJENkgDmzRrbjxQpwQAJVmBN6jF3SnwbQXv9vRixjH
58V33sb1G1RW+kXxQ3/e8jLX/4VaN479CufruXQp+IJWXsN/CH0lbC3k8m7u50d7
b1Zeqd/Yrh79rkc11b0X1698uGCSMlzz+V54Z0QOTEEX+nSu2ZZvccFS4UaHkn3z
rqDo00lb7rxQz8U25qro2OZrG6D3ub2q20TkWUB8EO4AOHkPn8KWP2r429Axrr0K
wlDWDTTt8/IsvPbuPf3T15RAhq1avkMXWn9nDXDjyWbpLfTn8NFnWmtesgY7Jl4t
GjbXC5WYekX3w2ZDB9KaT/DAMQ1a7RbMXNSz4RX4VbzDl+yYeSLmIh2G9fZb1PbB
PsIxrOgy4BquOWsJPm+zeFPSC3q9Cfu219L4AmxSjiZxC3dlosg5rIB892Mjoyv4
qxmg6oiqtc4Jxv+Gl9lRFVOqyHZrTC5IJ+xgfv1EyP6kKMUKLlDZtxZAuQxpUyxR
HZLq220RYnYSvkWauikq4M8fqFM8bdt6hLJnv7bVqllseROk9stCvjSiE3A9szH5
OgtOfYV5GhOeb8pCZqJKlGDw+RoJ21jtNCgOr6DgkNKV9CX/kL/Puwv8gnA0B0eh
dxCeB7f/gcLl7Cg3Z3gVVcGlgak6JWrLf5ITAJhBZ8Lv+AtL2DKmwEWS/iIMRmek
tLdh/a9GiCitqS0bT7GE
=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
To be consistent with other kernel interface namings, rename
of_get_named_gen_pool() to of_gen_pool_get(). In the original function
name "_named" suffix references to a device tree property, which contains
a phandle to a device and the corresponding device driver is assumed to
register a gen_pool object.
Due to a weak relation and to avoid any confusion (e.g. in future
possible scenario if gen_pool objects are named) the suffix is removed.
[sfr@canb.auug.org.au: crypto/marvell/cesa - fix up for of_get_named_gen_pool() rename]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This time we have support for few new devices, few new features and odd
fixes spread thru the subsystem.
New devices added
- support for CSRatlas7 dma controller
- Allwinner H3(sun8i) controller
- TI DMA crossbar driver on DRA7x
- new pxa driver
New features added:
- memset support is bought back now that we have a user in xdmac controller
- interleaved transfers support different source and destination strides
- supporting DMA routers and configuration thru DT
- support for reusing descriptors
- xdmac memset and interleaved transfer support
- hdmac support for interleaved transfers
- omap-dma support for memcpy
Others
- Constify platform_device_id
- mv_xor fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VM4w
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have support for few new devices, few new features and
odd fixes spread thru the subsystem.
New devices added:
- support for CSRatlas7 dma controller
- Allwinner H3(sun8i) controller
- TI DMA crossbar driver on DRA7x
- new pxa driver
New features added:
- memset support is bought back now that we have a user in xdmac controller
- interleaved transfers support different source and destination strides
- supporting DMA routers and configuration thru DT
- support for reusing descriptors
- xdmac memset and interleaved transfer support
- hdmac support for interleaved transfers
- omap-dma support for memcpy
Others:
- Constify platform_device_id
- mv_xor fixes and improvements"
* tag 'dmaengine-4.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: xgene: fix file permission
dmaengine: fsl-edma: clear pending interrupts on initialization
dmaengine: xdmac: Add memset support
Documentation: dmaengine: document DMA_CTRL_ACK
dmaengine: virt-dma: don't always free descriptor upon completion
dmaengine: Revert "drivers/dma: remove unused support for MEMSET operations"
dmaengine: hdmac: Implement interleaved transfers
dmaengine: Move icg helpers to global header
dmaengine: mv_xor: improve descriptors list handling and reduce locking
dmaengine: mv_xor: Enlarge descriptor pool size
dmaengine: mv_xor: add support for a38x command in descriptor mode
dmaengine: mv_xor: Rename function for consistent naming
dmaengine: mv_xor: bug fix for racing condition in descriptors cleanup
dmaengine: pl330: fix wording in mcbufsz message
dmaengine: sirf: add CSRatlas7 SoC support
dmaengine: xgene-dma: Fix "incorrect type in assignement" warnings
dmaengine: fix kernel-doc documentation
dmaengine: pxa_dma: add support for legacy transition
dmaengine: pxa_dma: add debug information
dmaengine: pxa: add pxa dmaengine driver
...
Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNoSAACgkQMUfUDdst+ymxNQCguSEmkAYNDdLyYhdcOqSxJt9u
U1gAoMThUDoomkx6CTDMU1wn53hxgMk9
=eCUS
-----END PGP SIGNATURE-----
Merge tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (152 commits)
Doc: serial-rs485.txt: update RS485 driver interface
Doc: tty.txt: remove mention of the BKL
MAINTAINERS: tty: add serial docs directory
serial: sprd: check for NULL after calling devm_clk_get
serial: 8250_pci: Correct uartclk for xr17v35x expansion chips
serial: 8250_pci: Add support for 12 port Exar boards
serial: 8250_uniphier: add bindings document for UniPhier UART
serial: core: cleanup in uart_get_baud_rate()
serial: stm32-usart: Add STM32 USART Driver
tty/serial: kill off set_irq_flags usage
tty: move linux/gsmmux.h to uapi
doc: dt: add documentation for nxp,lpc1850-uart
serial: 8250: add LPC18xx/43xx UART driver
serial: 8250_uniphier: add UniPhier serial driver
serial: 8250_dw: support ACPI platforms with integrated DMA engine
serial: of_serial: check the return value of clk_prepare_enable()
serial: of_serial: use devm_clk_get() instead of clk_get()
serial: earlycon: Add support for big-endian MMIO accesses
serial: sirf: use hrtimer for data rx
serial: sirf: correct the fifo empty_bit
...
It was a busy development cycle at this time, as you can see a wide
range of changes in diffstat. There are no big changes but many
refactoring and improvements. Here we go some highlights:
* ALSA core:
- Procfs codes were cleaned up to use seq_file
- Procfs can be opt out via Kconfig (only for EXPERT)
- Two types of jack API were unified finally; now both kctl and input
jack devs are handled via a single function call.
* HD-audio
- Continued code restructuring for the future ASoC driver; now HDA
controller driver is split to a core helper module.
- Preliminary codes for Skylake audio support in HDA core.
- Proper i915 gfx power well management for SKL & co
- Enabled runtime PM as default for Intel HDMI/DP codecs
- Newer Tegra chip supports
- More quirks for Dell headsets, Alienware (with CA0132), etc.
- A couple of DRM ELD helper API functions
* ASoC
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring
- Big refactoring, cleanup and enhancement for the Wolfson ADSP driver
- Cleanup series for TI TAS2552 and R-CAR drivers
- Fixes and improvements on RT56xx codecs
- Support for TI TAS571x power amplifiers
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs
- Support for x86 systems with RT5650 and Qualcomm Storm
- Support for Mediatek AFE (Audio Front End) unit
- Other various small fixes to ASoC codec drivers
* Firewire
- Enhanced to allow non-blocking streams to use timestamp
synchronization
- Improve support for DM1500 and BeBoBv3
* Misc
- Cleanup of old pci API functions over all PCI sound drivers
- Fix long-standing regression of the old powermac i2c setup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=D78E
-----END PGP SIGNATURE-----
Merge tag 'sound-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It was a busy development cycle at this time, as you can see a wide
range of changes in diffstat. There are no big changes but many
refactoring and improvements. Here we go some highlights:
ALSA core:
- Procfs codes were cleaned up to use seq_file
- Procfs can be opt out via Kconfig (only for EXPERT)
- Two types of jack API were unified finally; now both kctl and input
jack devs are handled via a single function call.
HD-audio:
- Continued code restructuring for the future ASoC driver; now HDA
controller driver is split to a core helper module.
- Preliminary codes for Skylake audio support in HDA core.
- Proper i915 gfx power well management for SKL & co
- Enabled runtime PM as default for Intel HDMI/DP codecs
- Newer Tegra chip supports
- More quirks for Dell headsets, Alienware (with CA0132), etc.
- A couple of DRM ELD helper API functions
ASoC:
- Support for loading ASoC topology maps from firmware, intended to
be used to allow self-describing DSP firmware images to be built
which can map controls added by the DSP to userspace without the
kernel needing to know about individual DSP firmwares
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring
- Big refactoring, cleanup and enhancement for the Wolfson ADSP
driver
- Cleanup series for TI TAS2552 and R-CAR drivers
- Fixes and improvements on RT56xx codecs
- Support for TI TAS571x power amplifiers
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs
- Support for x86 systems with RT5650 and Qualcomm Storm
- Support for Mediatek AFE (Audio Front End) unit
- Other various small fixes to ASoC codec drivers
Firewire:
- Enhanced to allow non-blocking streams to use timestamp
synchronization
- Improve support for DM1500 and BeBoBv3
Misc:
- Cleanup of old pci API functions over all PCI sound drivers
- Fix long-standing regression of the old powermac i2c setup"
* tag 'sound-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (533 commits)
ALSA: pcm: Fix pcm_class sysfs output
ALSA: hda-beep: Update authors dead email address
ASoC: wm_adsp: Move DSP Rate controls into the codec
ASoC: wm8995: Fix setting sysclk for WM8995_SYSCLK_MCLK2 case
ALSA: hda: provide default bus io ops extended hdac
ALSA: hda: add hda link cleanup routine
ALSA: hda: add hdac_ext stream creation and cleanup routines
ASoC: rsrc-card: remove unused ret
ALSA: HDAC: move SND_HDA_PREALLOC_SIZE to core
ASoC: mediatek: Add machine driver for rt5650 rt5676 codec
ASoC: mediatek: Add machine driver for MAX98090 codec
ASoC: mediatek: Add AFE platform driver
ASoC: rsnd: remove io from rsnd_mod
ASoC: rsnd: move rsnd_mod_is_working() to rsnd_io_is_working()
ASoC: rsnd: don't use rsnd_mod_to_io() on snd_kcontrol
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_src_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_ssi_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_dma_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_get_adinr()
ASoC: rsnd: add common interrupt handler for SSI/SRC/DMA
...
