We can easily run out of tx buf if there is any stuck in
transmission, so downgrade it to WARN_ON().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 already has one to keep track of number of failure
addba attempts.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_TX_CTL_AMPDU in tx control flags should be enough
to confirm BA is negotiated for that tid.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there was a reason I'm passing the ifidx I cannot
remember it any more and don't see one now, so let's
just pass the pointer itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit c3a8c5b6 ("cxgb3: move away from LLTX") exposed a bug in how
cxgb3 looks up the netdev_queue it stashes away in a qset during
initialization. For multiport devices, the TX queue index it uses is
offset by the first_qset index of each port. This leads to a crash
once LLTX is removed, since hard_start_xmit is called with one TX
queue lock held, while the TX reclaim timer task grabs a different
(wrong) TX queue lock when it frees skbs.
Fix this by removing the first_qset offset used to look up the TX
queue passed into t3_sge_alloc_qset() from setup_sge_qsets().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coexistence of Fiber Channel over Ethernet (FCoE) and Flow Director (FDIR)
in 82599 and remove the disabling of FDIR when FCoE is enabled.
Currently, FDIR is turned off when FCoE is enabled under the assumption that
FCoE is always enabled with DCB being turned on. However, FDIR does not have
to be turned off all the time when FCoE is enabled since FCoE can be enabled
without DCB being turned on, e.g., use link pause only. This patch makes sure
that when DCB is turned on or off, FDIR is turned on or off correspondingly;
and when FCoE is enabled, it does not disable FDIR, rather, it will have FDIR
set up properly so FCoE and FDIR can coexist regardless of DCB being on or off.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding smp_mb__after_lock define to be used as a smp_mb call after
a lock.
Making it nop for x86, since {read|write|spin}_lock() on x86 are
full memory barriers.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding memory barrier after the poll_wait function, paired with
receive callbacks. Adding fuctions sock_poll_wait and sk_has_sleeper
to wrap the memory barrier.
Without the memory barrier, following race can happen.
The race fires, when following code paths meet, and the tp->rcv_nxt
and __add_wait_queue updates stay in CPU caches.
CPU1 CPU2
sys_select receive packet
... ...
__add_wait_queue update tp->rcv_nxt
... ...
tp->rcv_nxt check sock_def_readable
... {
schedule ...
if (sk->sk_sleep && waitqueue_active(sk->sk_sleep))
wake_up_interruptible(sk->sk_sleep)
...
}
If there was no cache the code would work ok, since the wait_queue and
rcv_nxt are opposit to each other.
Meaning that once tp->rcv_nxt is updated by CPU2, the CPU1 either already
passed the tp->rcv_nxt check and sleeps, or will get the new value for
tp->rcv_nxt and will return with new data mask.
In both cases the process (CPU1) is being added to the wait queue, so the
waitqueue_active (CPU2) call cannot miss and will wake up CPU1.
The bad case is when the __add_wait_queue changes done by CPU1 stay in its
cache, and so does the tp->rcv_nxt update on CPU2 side. The CPU1 will then
endup calling schedule and sleep forever if there are no more data on the
socket.
Calls to poll_wait in following modules were ommited:
net/bluetooth/af_bluetooth.c
net/irda/af_irda.c
net/irda/irnet/irnet_ppp.c
net/mac80211/rc80211_pid_debugfs.c
net/phonet/socket.c
net/rds/af_rds.c
net/rfkill/core.c
net/sunrpc/cache.c
net/sunrpc/rpc_pipe.c
net/tipc/socket.c
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using early netconsole and gianfar driver this error pops up:
netconsole: timeout waiting for carrier
It appears that net/core/netpoll.c:netpoll_setup() is using
cond_resched() in a loop waiting for a carrier.
The thing is that cond_resched() is a no-op when system_state !=
SYSTEM_RUNNING, and so drivers/net/phy/phy.c's state_queue is never
scheduled, therefore link detection doesn't work.
I belive that the main problem is in cond_resched()[1], but despite
how the cond_resched() story ends, it might be a good idea to call
msleep(1) instead of cond_resched(), as suggested by Andrew Morton.
[1] http://lkml.org/lkml/2009/7/7/463
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix the following 'make includecheck' warning:
include/linux/rfkill.h: linux/types.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the mainline kernel, p54usb will fail because the TX queue length can
become < 0. This problem has been reported as Bugzilla #13725. The failure
is expressed by the following message in the logs:
WARNING: at net/mac80211/tx.c:1325 ieee80211_tx+0x23c/0x298 [mac80211]()
Hardware name: HP Pavilion dv2700 Notebook PC
tx refused but queue active
This problem has been recently observed in the wireless-testing tree, where
a full solution is being tested. That fix is too invasive for 2.6.31-rcX,
but the simple change supplied here will prevent the failure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Atheros top level menu needs a "depends WLAN_80211" to properly indent
within menuconfig and xconfig interfaces.
This is purely a visual issue but it effects all subsequent drivers.
The issue is the top level menu does not include a dependency on
WLAN_80211 so within the tree structure, Atheros is at the same level as
WLAN_80211 but when WLAN_80211 collapsed, the menu disappears along with
all subsequent drives, so it is really a subordinate.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These two functions no longer exist in mac80211,
so trying to insert them generates warnings in
the document.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a race condition -- started can be set to true
before channel is set due to the way mac80211 callbacks
currently work (->start should probably pass the channel
we would like to have initially). For now simply add a
check to hwsim to avoid dereferencing the NULL channel
pointer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: Clyde McPherson <ccmcphe@verizon.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: Clyde McPherson <ccmcphe@verizon.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yevgen Kotikov reported success on the sourceforge zd1211-devs list
with the following details:
Brand/retail: SONY IFU-WLM2
USB-IDs: Vendor: 0x054C Device: 0x0257
chip ID: zd1211b chip 054c:0257 v4802 high 00-0b-6b AL2230_RF pa0 -----
FCC ID: unknown
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Yevgen Kotikov <yevgen.kotikov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a shuttle machine here we got 07b8:6001 device, handled by zd1211rw, which does not work.
Scanning is OK but association does not work, we get "direct probe to AP xxx timed out"
It appears that this simple patch makes the device work perfectly.
This id was already there in initial import of the driver so I don't know if it has ever been
working as ZD1211 (which would mean they changed it and kept the id :( ).
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some PHYs require longer timeouts for carrier detection, and
auto-negotiation process may take indefinite amount of time.
It may be inconvenient to force longer timeouts for sane PHYs,
so let's introduce a kernel command line option.
Since we're using module_param(), the option also can be
changed in runtime.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drain the MAC TX fifos when a port goes down.
Back pressure might otherwise occur, leading to both
ports of the same adapter to hang.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Override the mac index computation for the gen2 adapter,
as each port is expected to use index 0.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the HW SMT table initialization to avoid random
mss miscomputations for offload connections.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use request_firmware() to load the phy's EDC programmation
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't always see the link status update interrupt
when we come out of reset and the peer is up.
Check and report the link status right before enabling interrupts.
Also fix LED settings, to get a consistent link status.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max packet size is not the only field in T3C's High Water Mark register.
Mask the register to access this field.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2 phys are were not getting the Global Tx disable bit set
when powered down, leading to an inconsistent link state
on peer.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing SUPPORTED_TP flag.
Update FW version checking.
Do the full initialization even if the FW version is unknown,
it might help catching further issues.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the r6040 device IRQ line is shared we will enter the driver
interrupt service routine, mask off the device interrupt enable
register (MIER) and return with IRQ_NONE, we would then leave the
device with interrupts disabled, this patch fixes that issue.
Reported-by: Steve Holland <sdh4@iastate.edu>
Signed-off-by: Joe Chou <joe.chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pawel Staszewski wrote:
<blockquote>
Some time ago i report this:
http://bugzilla.kernel.org/show_bug.cgi?id=6648
and now with 2.6.29 / 2.6.29.1 / 2.6.29.3 and 2.6.30 it back
dmesg output:
oprofile: using NMI interrupt.
Fix inflate_threshold_root. Now=15 size=11 bits
...
Fix inflate_threshold_root. Now=15 size=11 bits
cat /proc/net/fib_triestat
Basic info: size of leaf: 40 bytes, size of tnode: 56 bytes.
Main:
Aver depth: 2.28
Max depth: 6
Leaves: 276539
Prefixes: 289922
Internal nodes: 66762
1: 35046 2: 13824 3: 9508 4: 4897 5: 2331 6: 1149 7: 5
9: 1 18: 1
Pointers: 691228
Null ptrs: 347928
Total size: 35709 kB
</blockquote>
It seems, the current threshold for root resizing is too aggressive,
and it causes misleading warnings during big updates, but it might be
also responsible for memory problems, especially with non-preempt
configs, when RCU freeing is delayed long after call_rcu.
It should be also mentioned that because of non-atomic changes during
resizing/rebalancing the current lookup algorithm can miss valid leaves
so it's additional argument to shorten these activities even at a cost
of a minimally longer searching.
This patch restores values before the patch "[IPV4]: fib_trie root
node settings", commit: 965ffea43d from
v2.6.22.
Pawel's report:
<blockquote>
I dont see any big change of (cpu load or faster/slower
routing/propagating routes from bgpd or something else) - in avg there
is from 2% to 3% more of CPU load i dont know why but it is - i change
from "preempt" to "no preempt" 3 times and check this my "mpstat -P ALL
1 30"
always avg cpu load was from 2 to 3% more compared to "no preempt"
[...]
cat /proc/net/fib_triestat
Basic info: size of leaf: 20 bytes, size of tnode: 36 bytes.
Main:
Aver depth: 2.44
Max depth: 6
Leaves: 277814
Prefixes: 291306
Internal nodes: 66420
1: 32737 2: 14850 3: 10332 4: 4871 5: 2313 6: 942 7: 371 8: 3 17: 1
Pointers: 599098
Null ptrs: 254865
Total size: 18067 kB
</blockquote>
According to this and other similar reports average depth is slightly
increased (~0.2), and root nodes are shorter (log 17 vs. 18), but
there is no visible performance decrease. So, until memory handling is
improved or added parameters for changing this individually, this
patch resets to safer defaults.
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Reported-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that network interface is running before changing its MAC address.
Otherwise, rxch is accessed when it's NULL - causing a kernel oops.
Moreover, check that the new MAC address is valid.
Signed-off-by: Pablo Bitton <pablo.bitton@gmail.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Tested-by: Chaithrika U S <chaithrika@ti.com>
[tested on DM6467 EVM]
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb driver was defaulting to using the lock for pci-e function 0 for
all of the phys due to the fact that the lan id was not being set prior to
initialization. This change makes it so that the function id is set prior
to checking for the phy id.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can reclaim transmitted skbs to use in the receive path, so-called
skb recycling support.
Also reorder ucc_geth_poll() steps, so that we'll clean tx ring firstly,
thus maybe reclaim some skbs for rx.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rix is not found in mi->r[], i will become -1 after the loop. This value
is eventually used to access arrays, so we were accessing arrays with a
negative index, which is obviously not what we want to do. This patch fixes
this potential problem.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in cfg80211's cfg80211_bss_update erroneously
grabs a reference to the BSS, which means that it will
never be freed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29, 2.6.30]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the third (I think) polarity error I accidentally
introduced in the rfkill rewrite to make wireless work
again on (certain?) HP laptops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're missing a Kconfig help for the iwmc3200wifi driver.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we reclaim the tx desc, we always assume that the
last desc is a holding desc, which is not true, and skip it.
If the tx queue is drained during channel change, internal
reset and etc, the last descriptor may not be the holding
descriptor and we fail to reclaim them. This results in the
following two issues.
1. Tx stuck - We drop all the frames coming from upper layer
due to shortage in tx desc.
2. Crash - If we fail to reclaim a tx descriptor, we miss to
update the tx BA window with the seq number of the frame
associated to that desc, which, at some point, result in
the following crash due to an assert failure in ath_tx_addto_baw().
This patch fixes these two issues.
kernel BUG at ../drivers/net/wireless/ath/ath9k/xmit.c:180!
[155064.304164] invalid opcode: 0000 [#1] SMP
Call Trace:
[<fbc6d83b>] ? ath9k_tx+0xeb/0x160 [ath9k]
[<fbbc9591>] ipv6? __ieee80211_tx+0x41/0x120 [mac80211]
[<fbbcb5ae>] ? aes_i586ieee80211_master_start_xmit+0x28e/0x560 [mac80211]
[<c037e501>] aes_generic? _spin_lock_irqsave+0x31/0x40
[<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
[<c03058b5>] ? __qdisc_run+0x1b5/0x200
[<fbbcda5a>] ? af_packetieee80211_select_queue+0xa/0x100 [mac80211]
[<c02f53b7>] ? i915dev_queue_xmit+0x2e7/0x3f0
[<fbbc9b49>] ? ieee80211_subif_start_xmit+0x369/0x7a0 [mac80211]
[<c031bc35>] ? ip_output+0x55/0xb0
[<c02e0188>] ? show_memcpy_count+0x18/0x60
[<c02eb186>] ? __kfree_skb+0x36/0x90
[<c02f2202>] ? binfmt_miscdev_queue_xmit_nit+0xd2/0x110
[<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
[<c03058b5>] ? __qdisc_run+0x1b5/0x200
[<c033bca7>] ? scoarp_create+0x57/0x2a0
[<c02f53b7>] ? bridgedev_queue_xmit+0x2e7/0x3f0
[<c03034a0>] ? eth_header+0x0/0xc0
[<c033b95f>] stp? arp_xmit+0x5f/0x70
[<c033bf4f>] ? arp_send+0x5f/0x70
[<c033c8f5>] bnep? arp_solicit+0x105/0x210
[<c02fa5aa>] ? neigh_timer_handler+0x19a/0x390
[<c013bf88>] ? run_timer_softirq+0x138/0x210
[<c02fa410>] ? ppdevneigh_timer_handler+0x0/0x390
[<c02fa410>] ? neigh_timer_handler+0x0/0x390
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix condition in which radio LED did not initialize correctly, and remove
4 compilation warnings.
After the recent changes in rfkill, the radio LED used by b43/b43legacy
did not always initialize correctly.
Both b43 and b43legacy used the deprecated variable radio_enabled in
struct ieee80211_conf.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to unlock cfg80211_mutex in one fail path of
nl80211_set_wiphy.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The constant DMA_RX_MODE is defined to be 0x14 in the local include file
cs89x0.h. Since a constant with the same name is used elsewhere with
set_dma_mode, it seems likely that this constant could be used here.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1; identifier I; constant int C; @@
(
set_dma_mode(E1,I,...)
|
*set_dma_mode(E1,C,...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec: fix definition of 5272 version of FEC_X_DES_ACTIVE register
The ColdFire 5272 FEC driver has a different register address map
than other users of the FEC driver. And its definition of the
FEC_X_DES_ACTIVE register is incorrect, it should be 0x14.
The fec interface cannot transmit data with the old value.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
----
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checksum offload support for DM9000A and DM9000B chips.
v2 changes: added a local copy of ip_summed to save IO cycles in dm9000_send_packet
v3 changes: trans_start updating is removed.
Signed-off-by: Yeasah Pell <yeasah@comrex.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>