Different motherboards have different PNP declarations for
W83781D/W83782D chips. Some declare the whole range of I/O ports (8
ports), some declare only the useful ports (2 ports at offset 5) and
some declare fancy ranges, for example 4 ports at offset 4. To
properly handle all cases, request all ports individually for probing.
After we have determined that we really have a W83781D or W83782D
chip, the useful port range will be requested again, as a single
block.
I did not see a board which needs this yet, but I know of one for lm78
driver and I'd like to keep the logic of these two drivers in sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Different motherboards have different PNP declarations for LM78/LM79
chips. Some declare the whole range of I/O ports (8 ports), some
declare only the useful ports (2 ports at offset 5) and some declare
fancy ranges, for example 4 ports at offset 4. To properly handle all
cases, request all ports individually for probing. After we have
determined that we really have an LM78 or LM79 chip, the useful port
range will be requested again, as a single block.
This fixes the driver on the Olivetti M3000 DT 540, at least.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
The #define ADT7462_VOLT_COUNT is wrong, it should be 13 not 12. All the
for loops that use this as a limit count are of the typical form, "for
(n = 0; n < ADT7462_VOLT_COUNT; n++)", so to loop through all voltages
w/o missing the last one it is necessary for the count to be one greater
than it is. (Specifically, you will miss the +1.5V 3GPIO input with count
= 12 vs. 13.)
Signed-off-by: Ray Copeland <ray.copeland@aprius.com>
Acked-by: "Darrick J. Wong" <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
connector: Delete buggy notification code.
be2net: use eq-id to calculate cev-isr reg offset
Bluetooth: Use the control channel for raw HID reports
Bluetooth: Add DFU driver for Atheros Bluetooth chipset AR3011
Bluetooth: Redo checks in IRQ handler for shared IRQ support
Bluetooth: Fix memory leak in L2CAP
Bluetooth: Remove double free of SKB pointer in L2CAP
cdc_ether: Partially revert "usbnet: Set link down initially ..."
be2net: Fix memset() arg ordering.
bonding: bond_open error return value
ixgbe: if ixgbe_copy_dcb_cfg is going to fail learn about it early
ixgbe: set the correct DCB bit for pg tx settings
igbvf: fix issue w/ mapped_as_page being left set after unmap
drivers/net: ks8851_mll ethernet network driver
be2net: Bug fix to support newer generation of BE ASIC
starfire: clean up properly if firmware loading fails
mac80211: fix NULL pointer dereference when ftrace is enabled
netfilter: ctnetlink: fix expectation mask dump
ipv6: conntrack: Add member of user to nf_ct_frag6_queue structure
ath9k: fix eeprom INI values override for 2GHz-only cards
...
This is the counterpart to cba767175b
("pktcdvd: remove broken dev_t export of class devices"). Device is not
registered using dev_t, so it should not be destroyed using device_destroy
which looks up the device by dev_t. This will fail and adding the device
again will fail with the "duplicate name" error. This is fixed using
device_unregister instead of device_destroy.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The probe function passes a pointer to a struct fb_info to
platform_set_drvdata(), so don't interpret the return value of
platform_get_drvdata() as a pointer to struct imxfb_info.
The original imxfb_info *fbi backlight_power was NULL but in imxfb_suspend
it was 4 resulting in an oops as imxfb_suspend calls
imxfb_disable_controller(fbi) which in turn has
if (fbi->backlight_power)
fbi->backlight_power(0);
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
write_kmem() used to assume vwrite() always return the full buffer length.
However now vwrite() could return 0 to indicate memory hole. This
creates a bug that "buf" is not advanced accordingly.
Fix it to simply ignore the return value, hence the memory hole.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <tj@kernel.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise vmalloc_to_page() will BUG().
This also makes the kmem read/write implementation aligned with mem(4):
"References to nonexistent locations cause errors to be returned." Here we
return -ENXIO (inspired by Hugh) if no bytes have been transfered to/from
user space, otherwise return partial read/write results.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the kernel oops when dev_dbg is called with mx3_fbi->txd == NULL
Fix the late initialisation of mx3fb->backlight_level. If not, in the
chain of function started by init_fb_chan(), in __blank() call
sdc_set_brightness(mx3fb, mx3fb->backlight_level) that will shut down the
CONTRAST PWM output.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski <at> gmx.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Tue, Feb 02, 2010 at 02:57:14PM -0800, Greg KH (gregkh@suse.de) wrote:
> > There are at least two ways to fix it: using a big cannon and a small
> > one. The former way is to disable notification registration, since it is
> > not used by anyone at all. Second way is to check whether calling
> > process is root and its destination group is -1 (kind of priveledged
> > one) before command is dispatched to workqueue.
>
> Well if no one is using it, removing it makes the most sense, right?
>
> No objection from me, care to make up a patch either way for this?
Getting it is not used, let's drop support for notifications about
(un)registered events from connector.
Another option was to check credentials on receiving, but we can always
restore it without bugs if needed, but genetlink has a wider code base
and none complained, that userspace can not get notification when some
other clients were (un)registered.
Kudos for Sebastian Krahmer <krahmer@suse.de>, who found a bug in the
code.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: Do not idle on async queues
blk-cgroup: Fix potential deadlock in blk-cgroup
block: fix bugs in bio-integrity mempool usage
block: fix bio_add_page for non trivial merge_bvec_fn case
drbd: null dereference bug
drbd: fix max_segment_size initialization
cev-isr reg offset for each function is better calculated using (any) eq-id
alloted to that function instead of using pci-func number(which
does not work in some configurations...)
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves disable_controller() in the r8a66597-hdc
driver to disable all interrupts and clear status flags. It
also makes sure that disable_controller() is called during
probe(). This fixes the relatively rare case of unexpected
pending interrupts after kexec reboot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The spi_sh_msiof.c driver presently misconfigures REDG and TEDG. TEDG==0
outputs data at the **rising edge** of the clock and REDG==0 samples data
at the **falling edge** of the clock. Therefore for SPI, TEDG must be
equal to REDG, otherwise the last byte received is not sampled in SPI
mode 3.
This brings the driver in line with the SH7723 HW Reference Manual
settings documented in Figures 20.20 and 20.21 ("SPI Clock and data
timing").
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The previous changeset left behind an unused inode variable.
This patch removes it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As the padlock driver for SHA uses a software fallback to perform
partial hashing, it must implement custom import/export functions.
Otherwise hmac which depends on import/export for prehashing will
not work with padlock-sha.
Reported-by: Wolfgang Walter <wolfgang.walter@stwm.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
No other driver does anything remotely like this that I know of except
for the tty drivers, and I can't see any reason for random/urandom to do
it. In fact, it's a (trivial, harmless) timing information leak. And
obviously, it generates power- and flash-cycle wasting I/O, especially
if combined with something like hwrngd. Also, it breaks ubifs's
expectations.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Fix oops after radeon_cs_parser_init() failure.
drm/radeon/kms: move radeon KMS on/off switch out of staging.
drm/radeon/kms: Bailout of blit if error happen & protect with mutex V3
drm/vmwgfx: Don't send bad flags to the host
drm/vmwgfx: Request SVGA version 2 and bail if not found
drm/vmwgfx: Correctly detect 3D
drm/ttm: remove unnecessary save_flags and ttm_flag_masked in ttm_bo_util.c
drm/kms: Remove incorrect comment in struct drm_mode_modeinfo
drm/ttm: remove padding from ttm_ref_object on 64bit builds
drm/radeon/kms: release agp on error.
drm/kms/radeon/agp: Move the check of the aper_size after drm_acp_acquire and drm_agp_info
drm/kms/radeon/agp: Fix warning, format ‘%d’ expects type ‘int’, but argument 4 has type ‘size_t’
drm/ttm: Avoid conflicting reserve_memtype during ttm_tt_set_page_caching.
drm/kms/radeon: pick digitial encoders smarter. (v3)
drm/radeon/kms: use active device to pick connector for encoder
drm/radeon/kms: fix incorrect logic in DP vs eDP connector checking.
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/agp: Fix agp_amd64_init regression
x86: Add quirk for Intel DG45FC board to avoid low memory corruption
x86: Add Dell OptiPlex 760 reboot quirk
x86, UV: Fix RTC latency bug by reading replicated cachelines
oprofile/x86: add Xeon 7500 series support
oprofile/x86: fix crash when profiling more than 28 events
lib/dma-debug.c: mark file-local struct symbol static.
x86/amd-iommu: Fix deassignment of a device from the pt_domain
x86/amd-iommu: Fix IOMMU-API initialization for iommu=pt
x86/amd-iommu: Fix NULL pointer dereference in __detach_device()
x86/amd-iommu: Fix possible integer overflow
The WM8350 LED driver needs to be able to enable and disable the
regulators it is using. Previously the core wasn't properly enforcing
status change constraints so the driver was able to function but this
has always been intended to be required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If radeon_cs_parser_init() fails, radeon_cs_ioctl() calls
radeon_cs_parser_fini() with the non-zero error value. The latter dereferenced
parser->ib which hasn't been initialized yet -> boom. Add a test for parser->ib
being non-NULL before dereferencing it.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We are happy enough that the KMS driver is stable enough for enough people
for the kms enable/disable to leave staging. Distros can now contemplate
turning this on.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If an error happen in r600_blit_prepare_copy report it rather
than WARNING and keeping execution. For instance if ib allocation
failed we did just warn about but then latter tried to access
NULL ib ptr causing oops. This patch also protect r600_copy_blit
with a mutex as otherwise one process might overwrite blit temporary
data with new one possibly leading to GPU lockup.
Should partialy or totaly fix:
https://bugzilla.redhat.com/show_bug.cgi?id=553279
V2 failing blit initialization is not fatal, fallback to memcpy when
this happen
V3 init blit before startup as we pin in startup, remove duplicate
code (this one was actualy tested unlike V2)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes the driver not loading on older versions of VMware.
Signed-off-by: Peter Hanzel <hanzelpeter@gmail.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Re-order structure ttm_ref_object to remove 8 bytes of alignment padding
on 64 bit builds, so shrinking its size from 72 to 64 bytes allowing it
to fit into a smaller slab.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
First call drm_agp_acquire to check if agp has been acquired.
Second call drm_agp_info to fill in the info data struct, including aper_size.
Finally do the check to see if the aper_size makes sense.
Signed-off-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Fix warning by using %zu instead of %d for size_t
- Fix spelling mistake, "to" should be "too".
Signed-off-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes errors like:
> reserve_ram_pages_type failed 0x15b7a000-0x15b7b000, track 0x8, req 0x10
when a BO is moved between WC and UC areas.
Reported-by: Xavier Chantry <shiningxc@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
booting a Lenovo W500 with LVDS + DP outputs showed up a TODO we had
on our list, to pick a correct digital encoder block. The LVTMA
encoder requires the second digital encoder, all others can use any
encoder at all.
This fixes the digital encoder selection logic to enable LVDS/DP combos
to work okay.
V2: fix silly addition of connector dig_block and cleanup the other
places in the code that pick the encoder.
V3: rename to dig_encoder and clean up further - also fix
the picking algorithm.
tested on Lenovo W500 + desktop 3650 cards.
Signed-off-by: Dave Airlie <airlied@redhat.com>
On the W500 we have UNIPHY routed to both DVI and DP, this seems
to always pick the DVI connector which means link training fails.
Switch to using active device to pick the connector, this seems
like it should be safe from a code review, and it fixes things
a bit more here.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes the regression introduced by commit
42590a7501 ("x86/agp: Fix
agp_amd64_init and agp_amd64_cleanup").
The above commit changes agp_amd64_init() not to do anything if
gart_iommu_aperture is not zero.
If GART iommu calls agp_amd64_init(), we need to skip
agp_amd64_init() when it's called later via module_init.
The problem is that gart_iommu_init() calls agp_amd64_init()
with not zero gart_iommu_aperture so agp_amd64_init() is never
initialized.
When gart_iommu_init() calls agp_amd64_init(), agp should be
always initialized.
Reported-by: Marin Mitov <mitov@issp.bas.bg>
Reported-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Marin Mitov <mitov@issp.bas.bg>
Tested-by: Kevin Winchester <kjwinchester@gmail.com>
Cc: davej@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20100125141006O.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit ac019360fe changed the irq handler logic to BUG_ON rather than
returning IRQ_NONE when the incoming argument is invalid. While this
works in most cases, it doesn't work when the IRQ is shared with other
devices (or when DEBUG_SHIRQ is enabled).
So revert the previous change and replace the warning message with a
comment explaining that we want this behavior.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
An earlier commit removed the lock_kernel/unlock_kernel pair but forgot
to remove the unlock_kernel call in the cleanup path at the end of the
function.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
asic3 also needs tmio_core or otherwise will fail to build.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For pressure-based multi-touch devices, a direct way to send sensor
intensity data per finger is needed. This patch adds the ABS_MT_PRESSURE
event to the MT protocol.
Requested-by: Yoonyoung Shim <jy0922.shim@samsung.com>
Requested-by: Mika Kuoppala <mika.kuoppala@nokia.com>
Requested-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
