TCP probe log timestamps use struct timespec which is
not y2038 safe. Even though timespec might be good enough here
as it is used to represent delta time, the plan is to get rid
of all uses of timespec in the kernel.
Replace with struct timespec64 which is y2038 safe.
Prints still use unsigned long format and type.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP timestamp messages and IP source route options require
timestamps to be in milliseconds modulo 24 hours from
midnight UT format.
Add inet_current_timestamp() function to support this. The function
returns the required timestamp in network byte order.
Timestamp calculation is also changed to call ktime_get_real_ts64()
which uses struct timespec64. struct timespec64 is y2038 safe.
Previously it called getnstimeofday() which uses struct timespec.
struct timespec is not y2038 safe.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Example usage:
Set the skb priority using skbedit then allow it to be encoded
sudo tc qdisc add dev $ETH root handle 1: prio
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbedit prio 17 \
action ife encode \
allow prio \
dst 02:15:15:15:15:15
Note: You dont need the skbedit action if you are already encoding the
skb priority earlier. A zero skb priority will not be sent
Alternative hard code static priority of decimal 33 (unlike skbedit)
then mark of 0x12 every time the filter matches
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action ife encode \
type 0xDEAD \
use prio 33 \
use mark 0x12 \
dst 02:15:15:15:15:15
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Example usage:
Set the skb using skbedit then allow it to be encoded
sudo tc qdisc add dev $ETH root handle 1: prio
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbedit mark 17 \
action ife encode \
allow mark \
dst 02:15:15:15:15:15
Note: You dont need the skbedit action if you are already encoding the
skb mark earlier. A zero skb mark, when seen, will not be encoded.
Alternative hard code static mark of 0x12 every time the filter matches
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action ife encode \
type 0xDEAD \
use mark 0x12 \
dst 02:15:15:15:15:15
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action allows for a sending side to encapsulate arbitrary metadata
which is decapsulated by the receiving end.
The sender runs in encoding mode and the receiver in decode mode.
Both sender and receiver must specify the same ethertype.
At some point we hope to have a registered ethertype and we'll
then provide a default so the user doesnt have to specify it.
For now we enforce the user specify it.
Lets show example usage where we encode icmp from a sender towards
a receiver with an skbmark of 17; both sender and receiver use
ethertype of 0xdead to interop.
YYYY: Lets start with Receiver-side policy config:
xxx: add an ingress qdisc
sudo tc qdisc add dev $ETH ingress
xxx: any packets with ethertype 0xdead will be subjected to ife decoding
xxx: we then restart the classification so we can match on icmp at prio 3
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xdead \
u32 match u32 0 0 flowid 1:1 \
action ife decode reclassify
xxx: on restarting the classification from above if it was an icmp
xxx: packet, then match it here and continue to the next rule at prio 4
xxx: which will match based on skb mark of 17
sudo tc filter add dev $ETH parent ffff: prio 3 protocol ip \
u32 match ip protocol 1 0xff flowid 1:1 \
action continue
xxx: match on skbmark of 0x11 (decimal 17) and accept
sudo tc filter add dev $ETH parent ffff: prio 4 protocol ip \
handle 0x11 fw flowid 1:1 \
action ok
xxx: Lets show the decoding policy
sudo tc -s filter ls dev $ETH parent ffff: protocol 0xdead
xxx:
filter pref 2 u32
filter pref 2 u32 fh 800: ht divisor 1
filter pref 2 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:1 (rule hit 0 success 0)
match 00000000/00000000 at 0 (success 0 )
action order 1: ife decode action reclassify
index 1 ref 1 bind 1 installed 14 sec used 14 sec
type: 0x0
Metadata: allow mark allow hash allow prio allow qmap
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
xxx:
Observe that above lists all metadatum it can decode. Typically these
submodules will already be compiled into a monolithic kernel or
loaded as modules
YYYY: Lets show the sender side now ..
xxx: Add an egress qdisc on the sender netdev
sudo tc qdisc add dev $ETH root handle 1: prio
xxx:
xxx: Match all icmp packets to 192.168.122.237/24, then
xxx: tag the packet with skb mark of decimal 17, then
xxx: Encode it with:
xxx: ethertype 0xdead
xxx: add skb->mark to whitelist of metadatum to send
xxx: rewrite target dst MAC address to 02:15:15:15:15:15
xxx:
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 u32 \
match ip dst 192.168.122.237/24 \
match ip protocol 1 0xff \
flowid 1:2 \
action skbedit mark 17 \
action ife encode \
type 0xDEAD \
allow mark \
dst 02:15:15:15:15:15
xxx: Lets show the encoding policy
sudo tc -s filter ls dev $ETH parent 1: protocol ip
xxx:
filter pref 10 u32
filter pref 10 u32 fh 800: ht divisor 1
filter pref 10 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:2 (rule hit 0 success 0)
match c0a87aed/ffffffff at 16 (success 0 )
match 00010000/00ff0000 at 8 (success 0 )
action order 1: skbedit mark 17
index 6 ref 1 bind 1
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
action order 2: ife encode action pipe
index 3 ref 1 bind 1
dst MAC: 02:15:15:15:15:15 type: 0xDEAD
Metadata: allow mark
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
xxx:
test by sending ping from sender to destination
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow for more multicast router port information to be dumped such as
timer and type attributes. For that that purpose we need to extend the
MDBA_ROUTER_PORT attribute similar to how it was done for the mdb entries
recently. The new format is thus:
[MDBA_ROUTER_PORT] = { <- nested attribute
u32 ifindex <- router port ifindex for user-space compatibility
[MDBA_ROUTER_PATTR attributes]
}
This way it remains compatible with older users (they'll simply retrieve
the u32 in the beginning) and new users can parse the remaining
attributes. It would also allow to add future extensions to the router
port without breaking compatibility.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a temporary router port which doesn't depend only on the
incoming query. It can be refreshed if set to the same value, which is
a no-op for the rest.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed for the upcoming temporary port router. There's no point
to go through the logic if the value is the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using raw values makes it difficult to extend and also understand the
code, give them names and do explicit per-option manipulation in
br_multicast_set_port_router.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user explicitly requests VLAN filtering with something like:
# echo 1 > /sys/class/net/<bridge>/bridge/vlan_filtering
Switchdev propagates a SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING port
attribute.
Add support for it in the DSA layer with a new port_vlan_filtering
function to let drivers toggle 802.1Q filtering on user demand.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce devlink infrastructure for drivers to register and expose to
userspace via generic Netlink interface.
There are two basic objects defined:
devlink - one instance for every "parent device", for example switch ASIC
devlink port - one instance for every physical port of the device.
This initial portion implements basic get/dump of objects to userspace.
Also, port splitter and port type setting is implemented.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the initial implementation the only way to stop a rule from being
inserted into the hardware table was via the device feature flag.
However this doesn't work well when working on an end host system
where packets are expect to hit both the hardware and software
datapaths.
For example we can imagine a rule that will match an IP address and
increment a field. If we install this rule in both hardware and
software we may increment the field twice. To date we have only
added support for the drop action so we have been able to ignore
these cases. But as we extend the action support we will hit this
example plus more such cases. Arguably these are not even corner
cases in many working systems these cases will be common.
To avoid forcing the driver to always abort (i.e. the above example)
this patch adds a flag to add a rule in software only. A careful
user can use this flag to build software and hardware datapaths
that work together. One example we have found particularly useful
is to use hardware resources to set the skb->mark on the skb when
the match may be expensive to run in software but a mark lookup
in a hash table is cheap. The idea here is hardware can do in one
lookup what the u32 classifier may need to traverse multiple lists
and hash tables to compute. The flag is only passed down on inserts.
On deletion to avoid stale references in hardware we always try
to remove a rule if it exists.
The flags field is part of the classifier specific options. Although
it is tempting to lift this into the generic structure doing this
proves difficult do to how the tc netlink attributes are implemented
along with how the dump/change routines are called. There is also
precedence for putting seemingly generic pieces in the specific
classifier options such as TCA_U32_POLICE, TCA_U32_ACT, etc. So
although not ideal I've left FLAGS in the u32 options as well as it
simplifies the code greatly and user space has already learned how
to manage these bits ala 'tc' tool.
Another thing if trying to update a rule we require the flags to
be unchanged. This is to force user space, software u32 and
the hardware u32 to keep in sync. Thanks to Simon Horman for
catching this case.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offload decision was originally very basic and tied to if the dev
implemented the appropriate ndo op hook. The next step is to allow
the user to more flexibly define if any paticular rule should be
offloaded or not. In order to have this logic in one function lift
the current check into a helper routine tc_should_offload().
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements bookkeeping support to compute the maximum
headroom for all the devices in each datapath. When said value
changes, the underlying devs are notified via the
ndo_set_rx_headroom method.
This also increases the internal vports xmit performance.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On bridge needed_headroom changes, the enslaved devices are
notified via the ndo_set_rx_headroom method
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly, we need to update backlog too when we update qlen.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We saw qlen!=0 but backlog==0 on our production machine:
qdisc htb 1: dev eth0 root refcnt 2 r2q 10 default 1 direct_packets_stat 0 ver 3.17
Sent 172680457356 bytes 222469449 pkt (dropped 0, overlimits 123575834 requeues 0)
backlog 0b 72p requeues 0
The problem is we only count qlen for HTB qdisc but not backlog.
We need to update backlog too when we update qlen, so that we
can at least know the average packet length.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bottom qdisc decides to, for example, drop some packet,
it calls qdisc_tree_decrease_qlen() to update the queue length
for all its ancestors, we need to update the backlog too to
keep the stats on root qdisc accurate.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove nearly duplicated code and prepare for the following patch.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On reviewing the code I realized that GRE and UDP tunnels could cause a
kernel panic if we used GSO to segment a large UDP frame that was sent
through the tunnel with an outer checksum and hardware offloads were not
available.
In order to correct this we need to update the feature flags that are
passed to the skb_segment function so that in the event of UDP
fragmentation being requested for the inner header the segmentation
function will correctly generate the checksum for the payload if we cannot
segment the outer header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When selecting an address in context of a VRF, the vrf master should be
preferred for address selection. If it isn't, the user has a hard time
getting the system to select to their preference - the code will pick
the address off the first in-VRF interface it can find, which on a
router could well be a non-routable address.
Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
[dsa: Fixed comment style and removed extra blank link ]
Signed-off-by: David S. Miller <davem@davemloft.net>
David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces.
Relevant commands from his script:
ip addr add 9.9.9.9/32 dev lo
ip link set lo up
ip link add name vrf0 type vrf table 101
ip rule add oif vrf0 table 101
ip rule add iif vrf0 table 101
ip link set vrf0 up
ip addr add 10.0.0.3/32 dev vrf0
ip link add name dummy2 type dummy
ip link set dummy2 master vrf0 up
--> note dummy2 has no address - unnumbered device
ip route add 10.2.2.2/32 dev dummy2 table 101
ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02
tcpdump -ni dummy2 &
And using ping instead of his socat example:
$ ping -I vrf0 -c1 10.2.2.2
ping: Warning: source address might be selected on device other than vrf0.
PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.
>From tcpdump:
12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64
Note the source address is from lo and is not a VRF local address. With
this patch:
$ ping -I vrf0 -c1 10.2.2.2
PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.
>From tcpdump:
12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64
Now the source address comes from vrf0.
The ipv4 function for selecting source address takes a const argument.
Removing the const requires touching a lot of places, so instead
l3mdev_master_ifindex_rcu is changed to take a const argument and then
do the typecast to non-const as required by netdev_master_upper_dev_get_rcu.
This is similar to what l3mdev_fib_table_rcu does.
IPv6 for unnumbered interfaces appears to be selecting the addresses
properly.
Cc: David Lamparter <david@opensourcerouting.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines a new ETHTOOL_GLINKSETTINGS/SLINKSETTINGS API,
handled by the new get_link_ksettings/set_link_ksettings callbacks.
This API provides support for most legacy ethtool_cmd fields, adds
support for larger link mode masks (up to 4064 bits, variable length),
and removes ethtool_cmd deprecated
fields (transceiver/maxrxpkt/maxtxpkt).
This API is deprecating the legacy ETHTOOL_GSET/SSET API and provides
the following backward compatibility properties:
- legacy ethtool with legacy drivers: no change, still using the
get_settings/set_settings callbacks.
- legacy ethtool with new get/set_link_ksettings drivers: the new
driver callbacks are used, data internally converted to legacy
ethtool_cmd. ETHTOOL_GSET will return only the 1st 32b of each link
mode mask. ETHTOOL_SSET will fail if user tries to set the
ethtool_cmd deprecated fields to
non-0 (transceiver/maxrxpkt/maxtxpkt). A kernel warning is logged if
driver sets higher bits.
- future ethtool with legacy drivers: no change, still using the
get_settings/set_settings callbacks, internally converted to new data
structure. Deprecated fields (transceiver/maxrxpkt/maxtxpkt) will be
ignored and seen as 0 from user space. Note that that "future"
ethtool tool will not allow changes to these deprecated fields.
- future ethtool with new drivers: direct call to the new callbacks.
By "future" ethtool, what is meant is:
- query: first try ETHTOOL_GLINKSETTINGS, and revert to ETHTOOL_GSET if
fails
- set: query first and remember which of ETHTOOL_GLINKSETTINGS or
ETHTOOL_GSET was successful
+ if ETHTOOL_GLINKSETTINGS was successful, then change config with
ETHTOOL_SLINKSETTINGS. A failure there is final (do not try
ETHTOOL_SSET).
+ otherwise ETHTOOL_GSET was successful, change config with
ETHTOOL_SSET. A failure there is final (do not try
ETHTOOL_SLINKSETTINGS).
The interaction user/kernel via the new API requires a small
ETHTOOL_GLINKSETTINGS handshake first to agree on the length of the link
mode bitmaps. If kernel doesn't agree with user, it returns the bitmap
length it is expecting from user as a negative length (and cmd field is
0). When kernel and user agree, kernel returns valid info in all
fields (ie. link mode length > 0 and cmd is ETHTOOL_GLINKSETTINGS).
Data structure crossing user/kernel boundary is 32/64-bit
agnostic. Converted internally to a legal kernel bitmap.
The internal __ethtool_get_settings kernel helper will gradually be
replaced by __ethtool_get_link_ksettings by the time the first
"link_settings" drivers start to appear. So this patch doesn't change
it, it will be removed before it needs to be changed.
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the SO_CNX_ADVICE socket option (setsockopt only). The
purpose is to allow an application to give feedback to the kernel about
the quality of the network path for a connected socket. The value
argument indicates the type of quality report. For this initial patch
the only supported advice is a value of 1 which indicates "bad path,
please reroute"-- the action taken by the kernel is to call
dst_negative_advice which will attempt to choose a different ECMP route,
reset the TX hash for flow label and UDP source port in encapsulation,
etc.
This facility should be useful for connected UDP sockets where only the
application can provide any feedback about path quality. It could also
be useful for TCP applications that have additional knowledge about the
path outside of the normal TCP control loop.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all ipv6 addresses are flushed when the interface is configured
down, including global, static addresses:
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
inet6 2100:1::2/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
valid_lft forever preferred_lft forever
$ ip link set dev eth1 down
$ ip -6 addr show dev eth1
<< nothing; all addresses have been flushed>>
Add a new sysctl to make this behavior optional. The new setting defaults to
flush all addresses to maintain backwards compatibility. When the set global
addresses with no expire times are not flushed on an admin down. The sysctl
is per-interface or system-wide for all interfaces
$ sysctl -w net.ipv6.conf.eth1.keep_addr_on_down=1
or
$ sysctl -w net.ipv6.conf.all.keep_addr_on_down=1
Will keep addresses on eth1 on an admin down.
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
inet6 2100:1::2/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
valid_lft forever preferred_lft forever
$ ip link set dev eth1 down
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST> mtu 1500 state DOWN qlen 1000
inet6 2100:1::2/120 scope global tentative
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link tentative
valid_lft forever preferred_lft forever
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
msg.dst_sk needs to be set up with a valid socket because some callbacks
later derive the netns from it.
Fixes: 263ea09084d172d ("Revert "genl: Add genlmsg_new_unicast() for unicast message allocation")
Reported-by: Jon Maloy <maloy@donjonn.com>
Bisected-by: Jon Maloy <maloy@donjonn.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the TIPC module is unloaded, we have identified a race condition
that allows a node reference counter to go to zero and the node instance
being freed before the node timer is finished with accessing it. This
leads to occasional crashes, especially in multi-namespace environments.
The scenario goes as follows:
CPU0:(node_stop) CPU1:(node_timeout) // ref == 2
1: if(!mod_timer())
2: if (del_timer())
3: tipc_node_put() // ref -> 1
4: tipc_node_put() // ref -> 0
5: kfree_rcu(node);
6: tipc_node_get(node)
7: // BOOM!
We now clean up this functionality as follows:
1) We remove the node pointer from the node lookup table before we
attempt deactivating the timer. This way, we reduce the risk that
tipc_node_find() may obtain a valid pointer to an instance marked
for deletion; a harmless but undesirable situation.
2) We use del_timer_sync() instead of del_timer() to safely deactivate
the node timer without any risk that it might be reactivated by the
timeout handler. There is no risk of deadlock here, since the two
functions never touch the same spinlocks.
3: We remove a pointless tipc_node_get() + tipc_node_put() from the
timeout handler.
Reported-by: Zhijiang Hu <huzhijiang@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we have never seen it happen, we have identified the
following problematic scenario when nodes are stopped and deleted:
CPU0: CPU1:
tipc_node_xxx() //ref == 1
tipc_node_put() //ref -> 0
tipc_node_find() // node still in table
tipc_node_delete()
list_del_rcu(n. list)
tipc_node_get() //ref -> 1, bad
kfree_rcu()
tipc_node_put() //ref to 0 again.
kfree_rcu() // BOOM!
We fix this by introducing use of the conditional kref_get_if_not_zero()
instead of kref_get() in the function tipc_node_find(). This eliminates
any risk of post-mortem access.
Reported-by: Zhijiang Hu <huzhijiang@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN GetNext operation is specific to some switches, and thus can be
complicated to implement for some drivers.
Remove the support for the vlan_getnext/port_pvid_get approach in favor
of the generic and simpler port_vlan_dump function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to port_fdb_dump, add a port_vlan_dump function to DSA drivers
which gets passed the switchdev VLAN object and callback.
This function, if implemented, takes precedence over the soon legacy
vlan_getnext/port_pvid_get approach.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tc actions are stored in a per-module hashtable,
therefore are visible to all network namespaces. This is
probably the last part of the tc subsystem which is not
aware of netns now. This patch makes them per-netns,
several tc action API's need to be adjusted for this.
The tc action API code is ugly due to historical reasons,
we need to refactor that code in the future.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only release the memory of the hashtable itself, not its
entries inside. This is not a problem yet since we only call
it in module release path, and module is refcount'ed by
actions. This would be a problem after we move the per module
hinfo into per netns in the latter patch.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to try and pull the L4 header in if it is available in the first
fragment. As such add the flag to indicate we want to pull the headers on
the first fragment in.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 parsing was using a local pointer when it could use the same
pointer as the IPv4 portion of the code since the key_addrs can support
both IPv4 and IPv6 as it is just a pointer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow dissector bits handling FCoE didn't bother to actually validate
that the space there was enough for the FCoE header. So we need to update
things so that if there is room we add the header and report a good result,
otherwise we do not add the header, and report the bad result.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that for IPv4 we were reporting the ip_proto of the fragment,
and for IPv6 we were not. This patch updates that behavior so that we
always report the IP protocol of the fragment. In addition it takes the
steps of updating the payload offset code so that we will determine the
start of the payload not including the L4 header for any fragment after the
first.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the logic for the IPv4 parsing so that it is consistent
with how we handle IPv6. Specifically if we do not have the flow key
indicating we want the addresses we still may need to take a look at the IP
fragmentation bits and to see if we should stop after we have recognized
the L3 header.
Fixes: 807e165dc44f ("flow_dissector: Add control/reporting of fragmentation")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the validation checks for the new array-based TCP SO_REUSEPORT
validation was unintentionally dropped in ea8add2b1903. This adds it back.
Lack of this check allows the user to allocate multiple sock_reuseport
structures (leaking all but the first).
Fixes: ea8add2b1903 ("tcp/dccp: better use of ephemeral ports in bind()")
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor all assignments to rfkill_global_states[].cur into a single
function rfkill_update_global_state().
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This prepares the driver for removal of platform data.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Helper for finding the type based on name. Useful if the
type needs to be determined based on device property.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[modify rfkill_types array and BUILD_BUG_ON to not cause errors]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add IEEE80211_RADIOTAP_VHT entry to rtap_namespace_sizes array in order to
define alignment and size of VHT info in tx radiotap
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
