When statistics are polled from sysfs, the statistics use the same
commands as the adapter initialization. Change the messages printed
here, so they are only printed during initialization and not for each
poll of adapter data.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When sending a exchange config data command, wait for a free SBAL.
This does not matter during adapter initialization, but this is
required for pulling adapter statistics during high I/O load.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (137 commits)
[SCSI] iscsi: bidi support for iscsi_tcp
[SCSI] iscsi: bidi support at the generic libiscsi level
[SCSI] iscsi: extended cdb support
[SCSI] zfcp: Fix error handling for blocked unit for send FCP command
[SCSI] zfcp: Remove zfcp_erp_wait from slave destory handler to fix deadlock
[SCSI] zfcp: fix 31 bit compile warnings
[SCSI] bsg: no need to set BSG_F_BLOCK bit in bsg_complete_all_commands
[SCSI] bsg: remove minor in struct bsg_device
[SCSI] bsg: use better helper list functions
[SCSI] bsg: replace kobject_get with blk_get_queue
[SCSI] bsg: takes a ref to struct device in fops->open
[SCSI] qla1280: remove version check
[SCSI] libsas: fix endianness bug in sas_ata
[SCSI] zfcp: fix compiler warning caused by poking inside new semaphore (linux-next)
[SCSI] aacraid: Do not describe check_reset parameter with its value
[SCSI] aacraid: Fix down_interruptible() to check the return value
[SCSI] sun3_scsi_vme: add MODULE_LICENSE
[SCSI] st: rename flush_write_buffer()
[SCSI] tgt: use KMEM_CACHE macro
[SCSI] initio: fix big endian problems for auto request sense
...
In the case the unit is blocked, zfcp_unit_get has not been called
yet, so the error handling path should not call zfcp_unit_put.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/s390/scsi/zfcp_aux.c: In function ‘zfcp_fsf_incoming_els_rscn’:
drivers/s390/scsi/zfcp_aux.c:1379: warning: cast from pointer to integer of
different size
drivers/s390/scsi/zfcp_aux.c: In function ‘zfcp_fsf_incoming_els_plogi’:
drivers/s390/scsi/zfcp_aux.c:1432: warning: cast from pointer to integer of
different size
drivers/s390/scsi/zfcp_aux.c: In function ‘zfcp_fsf_incoming_els_logo’:
drivers/s390/scsi/zfcp_aux.c:1457: warning: cast from pointer to integer of
different size
..
Just passing pointers rids us of these warnings and improves readability.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
as seen in linux-next tree:
drivers/s390/scsi/zfcp_dbf.c: In function ‘zfcp_rec_dbf_event_thread’:
drivers/s390/scsi/zfcp_dbf.c:697: warning: passing argument 1 of ‘atomic_read’
from incompatible pointer type
Caused by recent git commit:
commit 348447e857
Author: Martin Peschke <mp3@de.ibm.com>
Date: Thu Mar 27 14:22:01 2008 +0100
[SCSI] zfcp: Add trace records for recovery thread and its queues
We are not supposed to poke inside semaphore.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Remove line breaks that do not conform to coding style.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Saving on line breaks, improving readability, by shortening excessive
function names and identifiers, by simplifying some functions call
chains, and by simplifying nesting of some data structure.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Unclutter the global zfcp_def.h header. Move everything required to
call into the debug feature to a new header file.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Simplify usage of zfcp_dbf_tag() and calling functions.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Simplify usage of output function for hex dumps.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Improve readability of code by using more convenient output function.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Change zfcp_dbf_timestamp() so that it just calculates timespec from
timestamp. First step to be able to rip this code out of zfcp.
Besides, this change makes it easier to rip out old-style debug view
functions.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch removes the now obsolete erp_dbf trace.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch writes trace records for various phases of a recovery action:
action being created, action being processed, action continueing
asynchronously, action gone, action timed out, action dismissed etc.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch allows any recovery event to be traced back to an exact
cause, e.g. a particular request identified by an id (address).
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch writes a trace record which provides information about state
changes for adapters, ports and units, e.g. target failure, targets becoming
online, targets being temporarily blocked due to pending recovery, targets
which have been recovered successfully etc.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch writes trace records which provide information about the
operation of the zfcp error recovery thread and the queues it works
on.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch registers the new recovery trace with the s390 debug
feature.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Introducing helper functions that allow for code simpfifications.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds per request hardware debugging data to the trace
record which is written per request. It's a replacement for some sad
kernel message based debugging code. Considering the amount of trace
data, printk() is not suitable for this stuff. Writing binary traces
is more efficient. In addition we got all information in one place.
The QTCB trace data is only dumped for requests other than SCSI
requests. Otherwise we would flood the trace ring buffer. We are
mostly interested in non-SCSI, recovery related requests here anyway.
This patch also works around a known hardware bug. It truncates QTCB
traces so that we do not save unused areas of the hardware trace.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Is not appropriate to printk() tons of hardware trace data.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Clean up _zfcp_san_dbf_event_common_els using zfcp_dbf_hexdump()
helper.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a FSF physical close returns the status boxed, this means that
another system already closed the port. For our system this is the
same status as in the good path, we have to send the normal close. So,
set the status for the boxed response to the same as for the good
status.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[based on proposal from Mike Christie <michaelc@cs.wisc.edu>, this
patch adds some simplifications to the handler functions]
With the new target reset handler callback in the SCSI midlayer, the
device reset handler in zfcp can be split in two parts. Now, zfcp does
not have to track anymore whether the device supports LUN resets, so
remove this flag and let the SCSI midlayer decide what to do.
The device reset handler simply issues a LUN reset and the target
reset handler a target reset.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The commit de25deb180 changed
scsi_cmnd.sense_buffer from a static array to a dynamically allocated
buffer. We can't access to sense_buffer in '&cmd->sense_buffer' way.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
We need to hold the queue-lock when checking whether we still have a valid
unit/port handle for the task management command, i.e whether we can issue this
request for this unit/port. If the error recovery is about to close this
unit/port, then it competes for the queue-lock. If the close request issued by
the error recovery wins, then it is guaranteed that this unit/port has been
blocked for other requests.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We need to hold the queue-lock when checking whether we still have a valid
unit/port handle for the FCP command, i.e whether we can issue this request for
this unit/port. If the error recovery is about to close this unit/port, then it
competes for the queue-lock. If the close request issued by the error recovery
wins, then it is guaranteed that this unit/port has been blocked for other
requests.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We need to hold the queue-lock when checking whether we still have a valid port
handle for the ELS command, i.e whether we can issue this request for this
port. If the error recovery is about to close this port, then it competes for
the queue-lock. If the close request issued by the error recovery wins, then it
is guaranteed that this port has been blocked for other requests.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We need to hold the queue-lock when checking whether we still have a valid
unit/port handle for the abort command, i.e whether we can issue this request
for this unit/port. If the error recovery is about to close this unit/port,
then it competes for the queue-lock. If the close request issued by the error
recovery wins, then it is guaranteed that this unit/port has been blocked for
other requests.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
According to the FSF spec, word 0 (bytes 0-3) has the handle
specified with the abort command and word 1 (bytes 4-7) has the
handle for the command to be aborted. Fix the if statements
that try to compare those.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
zfcp_erp_strategy_check_fsfreq() checks if it is safe to access the
fsf_req associated with the erp_action that gets passed. To test if
it is safe it accesses the fsf_req in order to get its index into
the hash list. This is broken since the fsf_req might be freed already
and the read index has no meaning. It could lead to memory corruption.
Fix this by introducing a new zfcp_reqlist_find_safe() method which
just checks if addresses are equal. This is slower, but only gets
called in case of error recovery.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove tracing for request with a "qualifier" field set in the
response. The protocol status qualifier now contains measurement
data for "good" commands, so this check would trace every response
by default.
The fix is to simply remove the "qual" tracing: The responses with an
interesting status are also traced as "ferr" or "perr" and all
responses can be traced as "norm" with a higher trace level.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When adding an invalid LUN, there is a deadlock between the add
via scsi_scan_target and the slave_destroy handler: The handler
waits for the scan to complete, but for an invalid unit,
scsi_scan_target directly calls the slave_destroy handler.
Fix the deadlock by removing the wait in the slave_destroy
handler, it was not necessary anyway.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The common I/O layer can call remove a handler to inform zfcp
that a device disappeared. The handler zfcp_ccw_remove then
removes all unit, port and the adapter data structures. Removing
the units requires that the SCSI devices are removed first.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
It is not necessary to use jiffies or milliseconds to specify
waiting times that last a couple of seconds.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The callback function used by zfcp always returns success,
which is an indication for the SCSI midlayer to stop error
handling. Remove the bus_reset callback, since the same
function will be called via the host_reset callback.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Calling zfcp_erp_strategy_check_action() after zfcp_erp_action_to_running()
in zfcp_erp_strategy() might cause an unbalanced up() for erp_ready_sem,
which makes the zfcp recovery fail somewhere along the way:
erp thread processing erp_action:
|
| someone waking up erp thread for erp_action
| |
| | someone else dismissing erp_action:
| | |
V V V
write_lock_irqsave(&adapter->erp_lock, flags);
...
if (zfcp_erp_action_exists(erp_action) == ZFCP_ERP_ACTION_RUNNING) {
zfcp_erp_action_to_ready(erp_action);
up(&adapter->erp_ready_sem); /* first up() for erp_action */
}
write_unlock_irqrestore(&adapter->erp_lock, flags);
write_lock_irqsave(&adapter->erp_lock, flags);
...
zfcp_erp_action_to_running(erp_action);
write_unlock_restore(&adapter->erp_lock, flags);
/* processing erp_action */
write_lock_irqsave(&adapter->erp_lock, flags);
...
erp_action->status |= ZFCP_STATUS_ERP_DISMISSED;
if (zfcp_erp_action_exists(erp_action) ==
ZFCP_ERP_ACTION_RUNNING) {
zfcp_erp_action_to_ready(erp_action);
up(&adapter->erp_ready_sem);
/* second, unbalanced up() for erp_action */
}
...
write_unlock_restore(&adapter->erp_lock, flags);
write_lock_irqsave(&adapter->erp_lock, flags);
if (erp_action->status & ZFCP_STATUS_ERP_DISMISSED) {
zfcp_erp_action_dequeue(erp_action);
retval = ZFCP_ERP_DISMISSED;
}
...
write_unlock_restore(&adapter->erp_lock, flags);
down(&adapter->erp_ready_sem);
/* this down() is meant to balance the first up() */
The erp thread must not dismiss an erp_action after moving that action to
erp_running_head. Instead it should just go through the down() operation,
which balances the first up(), and run through zfcp_erp_strategy one more
time for the second up(), which eventually cleans up erp_action. Which
is similar to the normal processing of an event for erp_action doing
something asynchronously (e.g. waiting for the completion of an fsf_req).
This only works if we make sure that a dismissed erp_action is passed to
zfcp_erp_strategy() prior to the other action, which caused actions to be
dismissed. Therefore the patch implements this rule: running actions go to
the head of the ready list; new actions go to the tail of the ready list;
the erp thread picks actions to be processed from the ready list's head.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
zfcp_erp_action_dismiss() used to ignore any actions in the ready list. This
is a bug. Any action superseded by a stronger action needs to be dismissed.
This patch changes zfcp_erp_action_dismiss() so that it dismisses actions
regardless of their list affiliation. The ERP thread is able to handle this.
It is important to kick the erp thread only for actions in the running list,
though, as an imbalance of wakeup signals would confuse the erp thread
otherwise.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Cleanup the whitepace from the entire zfcp driver to prevent
to have those changes in future feature or function patches.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Already register the debug feature before the zfcp adapter is
set online. This allows to use the debug feature to investigate
the online/offline sequence.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
cleanup, using ERP request mempool for all ERP versions of
the exchange functions (exchange_config (ECD), exchange_port (EPD) )
providing individual versions of the ECD, EPD functions for ERP
and other purposes (_sync).
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove braces for only one statement
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
zfcp_adapter_enqueue initialized adapter->ccw_device twice with
the same value. Remove the second assignment, since it is not
necessary.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Avoid "if (whatever) ;" constructs since they seem to confuse people,
even if there is a comment.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Also removes a bunch of ^L in drivers/s390/cio/cmf.c
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce a shutdown method for the ccw bus that calls the driver
specific shutdown method in struct ccw_driver.
Switch zfcp to the new ccw_driver shutdown method.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the data buffer accessor patch.
For request without a data buffer nothing was written into
a SBALE.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Get rid of two 'warning: Using plain integer as NULL pointer'.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Memory allocated with kmalloc is always initialzed to 0 with memset.
Replace the two calls with kzalloc, that already does both steps.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When reporting SCSI devices to the SCSI midlayer, use the FCP LUN as
LUN reported to the SCSI layer. With this approach, zfcp does not have
to create unique LUNS, and this code can be removed.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In some cases we did not reset some adapter status flags properly.
This patch clears these flags during FCP adapter shutdown.
Signed-off-by: Volker Sameske <sameske@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
IO stall after deleting and path checker changes after reenabling zfcp device
Setting one zfcp device offline using chccwdev in a multipath
environment and waiting will lead to IO stall on all paths.
After setting the zfcp device back online using chccwdev,
the devices with io stall will have a different path checker.
Devices corresponding to the deleted units are never freed.
This has the effect that 'slave_destroy' is never called and zfcp
still thinks that this unit is registered
(ZFCP_STATUS_UNIT_REGISTERED is still set). Hence the erp
routine is not called correctly and the unit is not enabled properly.
Do not delete rport and the sdev. Just set the host to block on
'offline'. Setting host online again will then remove the blocked status
and everything is fine again.
Signed-off-by: Michael Loehr <mloehr2@linux.vnet.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
avoid clutter in erp_dbf
cleanup zfcp_fsf_req_dismiss functions:
- avoid clutter in erp_dbf (reqs_active is always 0)
- fold called three-line function into calling function
- add meaningful comment
- coding style
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The boxed flag for units was never cleared. This doesn't hurt, but on
ACL updates the error recovery could reopen more units than needed.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Must clear adapter failed flag if an fsf request times out. This is
necessary because on link down situations the failed flags gets set
but the QDIO queues are still up. Since an adapter reopen will be
skipped if the failed flag is set an adapter_reopen that is issued
on fsf request timeout has no effect if the local link is down.
Might lead to locked up system if the SCSI stack is waiting for abort
completion.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify request ID management and make sure that frequently used
functions are inlined. Also fix a memory leak in zfcp_adapter_enqueue()
which only gets hit in error handling.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SCSI stack requires low level drivers to register and
unregister devices. For zfcp this leads to the situation where
zfcp calls the SCSI stack, the SCSI tries to scan the new device
and the scan SCSI command fails. This would require the zfcp erp,
but the erp thread is already blocked in the register call.
The fix is to make sure that the calls from the ERP thread to
the SCSI stack do not block the ERP thread. In detail:
1) Use a workqueue to avoid blocking of the scsi_scan_target calls.
2) When removing a unit make sure that no scsi_scan_target call is
pending.
3) Replace scsi_flush_work with scsi_target_unblock. This avoids
blocking and has the same result.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is a possible race condition while generating the unique
request ids and sequence numbers. Both might be read at the
same time and have the same value. Fix this by serializing the
access through the queue lock of the adapter: First call
zfcp_fsf_req_sbal_get that acquires the lock, then read and
increment the unique ids.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
S_ID and D_ID are defined in the FCP spec as 3 byte fields.
Change the output in zfcp print statements accordingly to print
them with only 3 bytes.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For each request that is sent to the FCP adapter, zfcp allocates
memory. Status information and data that is being read from the
device is written to this memory by the hardware. After that,
the hardware signals this via the response queue and zfcp
continues processing.
Now, if zfcp detects that there is a signal for an incoming
response from the hardware, but there is no outstanding request
for that request id, then some memory that can be in use anywhere
in the system has just been overwritten. This should never happen,
but if it does, stop the system with a panic.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Invalid locking order. Kernel hangs after trying to take two locks
which are dependend on each other. Introducing temporary variable
to free requests. Free lock after requests are copied.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All on stack DECLARE_COMPLETIONs should be replaced by:
DECLARE_COMPLETION_ONSTACK
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the fix ... One of my previous fixes introduced removal of all fsf
requests in zfcp's eh_host_reset_handler. But this must not happen
before qdio queues are shut down. So, I revert the changes of
zfcp_scsi_eh_host_reset_handler.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This instance will be used whenever a timer is needed for
a request by zfcp.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
zfcp's eh_abort_handler used the wrong request ID to
identify the request to be aborted. The bug was introduced
with commit fea9d6c7bc
for improved management of request IDs. The bug is
fixed with this patch.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Create private slab caches in order to guarantee proper alignment of
data structures that get passed to hardware.
Sidenote: with this patch slab cache debugging will finally work on s390
(at least no known problems left).
Furthermore this patch does some minor cleanups:
- store ptr for transport template in struct zfcp_data
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Compile fix ups and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use do { } while (0) constructs instead of empty defines to avoid
subtle compile bugs.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Bug fixes for zfcp's erp:
- trigger adapter reopen if do_QDIO fails
- avoid erp deadlock if registration of scsi target or remote port hang
- do not treat as error if exchange port data fails
- decrease timeout for target reset and aborts
- mark unit failed if slave_destroy is called
Additionally some code cleanup was done:
- made some functions void when retval is not of interest
- shortened initialization of zfcp's host_template
- corrected some comments
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve request handling. Use hash table to manage request IDs.
Signed-off-by: Volker Sameske <sameske@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bump up version number, skip "4.6.0" because this might
clash with zfcp version in certain distros.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If zfcp's port erp fails we now call fc_remote_port_delete. This helps
to avoid offlined scsi devices if scsi commands time out due to path
failures. When an adapter erp fails we call fc_remote_port_delete for
all ports on that adapter.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace hex dump of bit error threshold data by log message showing
bit error threshold data human readable.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Removed some macros, struct members and typedefs which were
unused or not necessary.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace kmalloc/memset by kzalloc or kcalloc.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch changes several mempool users, all of which are basically just
wrappers around kmalloc(), to use the common mempool_kmalloc/kfree, rather
than their own wrapper function, removing a bunch of duplicated code.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch fixes following issues:
(1) Replace scsi_add_device with scsi_scan_target.
(Thus the rport instead of the scsi_host becomes parent of a
scsi_target again.)
(2) Avoid scsi_device allocation during registration of an remote port.
(Would be done during fc_scsi_scan_rport.)
(3) Fix queuecommand behaviour when an zfcp unit is blocked.
(Call scsi_done with DID_NO_CONNECT instead of returning
SCSI_MLQUEUE_DEVICE_BUSY otherwise we might end up waiting
for completion in blk_execute_rq for ever.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It fixes a bug in zfcp which provokes a race
in scsi_scan.c. Finally this can lead to an Oops like:
kernel BUG at fs/sysfs/symlink.c:87!
Correctly set this_id for the host. Otherwise we provoke
a race between scsi_target_reap_work and concurrent
scsi_add_device.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Flush workqueue of a scsi host after a remote port for that host
is registered at the fc transport class. Otherwise immediate
registration of a scsi device on that host is racy.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Avoid access to old fsf_requests if device reset is logged.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove endless polling for replug of the local link. Just wait for
link up notification.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove all remainders of obsolete zfcp adapter attributes physical_wwpn and
physical_s_id.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Remove all CVS generated information like e.g. revision IDs from
drivers/s390 and include/asm-s390 (none present in arch/s390).
- Add newline at end of arch/s390/lib/Makefile to avoid diff message.
Acked-by: Andreas Herrmann <aherrman@de.ibm.com>
Acked-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replaced zfcp adapter attributes with fc_host attributes:
fc_topology by port_type, physical_wwpn by permanent_port_name.
Make use of fc_host attribute supported_speeds.
Removed zfcp adapter attribute physical_s_id.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Added host stats, removed superfluous get_starget_ functions,
removed some attributes from zfcp specific sysfs tree (e.g.
scsi_host_no, scsi_lun, wwnn and d_id).
Host stats are given for the physical adapter port not for the
virtual adapter. Reset stats is implemented in the device driver.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Handle unsolicited adapter status that informs about loss of
previous unsolicited status notification(s).
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change return code in slave_alloc to avoid irritating error message from
scsi_alloc_sdev() when scsi stack tries target scan.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Don't check link down payload in case of firmware update.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed various problems in opening sequence of adapters which was previously
changed with NPIV support:
o corrected handling when exchange port data function is not supported,
otherwise adapters on z900 cannot be opened anymore
o corrected setup of timer for exchange port data if called from error
recovery
o corrected check of return code of exchange config data
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move initialization of locks and lists to adapter allocation function.
Otherwise we might end up with some uninitialized locks, like e.g. the
erp locks which only will be inititialized if an error recovery thread
for an adapter will be started.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the drivers/s390/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/s390/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Cornelia Huck <cohuck@de.ibm.com>
Acked-by: Stefan Bader <Stefan.Bader@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this patch adds some fc host attributes and removes its equivalents
from the zfcp_adapter structure and zfcp specific sysfs subtree.
Furthermore it removes superfluous calls to fc_remort_port_delete when
an adapter is set offline because rports will be removed by
fc_remove_host anyway.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
N_Port ID Virtualization (NPIV) allows a single FCP port to appear as
multiple, distinct ports providing separate port identification. NPIV
is supported by FC HBAs on System z9. zfcp was adapted to support this
new feature.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Debug features (DBFs) els_dbf, cmd_dbf and abt_dbf were removed and
san_dbf, hba_dbf and scsi_dbf were introduced. The erp_dbf did not
change.
The new traces improve debugging of problems with zfcp, scsi-stack,
multipath and hardware in the SAN. san_dbf traces things like ELS and
CT commands, hba_dbf saves HBA specific information of requests, and
scsi_dbf saves FCP and SCSI specific information of requests. Common
to all new DBFs is that they provide a so called structured view. This
significantly improves readability of the traces.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
o union zfcp_req_data removed
o increment unit refcount when processing FCP commands
(This fixes a theoretical race: When all scsi commands of a unit
are aborted and the scsi_device is removed then the unit could be
removed before all fsf_requests of that unit are completely processed.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
o always use locking when changing erp_action lists,
o avoid escalation to ERP_ACTION_REOPEN_PORT_FORCED if erp_action is
still in use for ERP_ACTION_REOPEN_PORT
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bugfix (usage of uninitialized pointer in zfcp_port_dequeue) and compile
fixes for the zfcp device driver.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a severe problem with 2.6.13-rc7.
Due to recent SCSI changes it is not possible to add any LUNs to the zfcp
device driver anymore. With registration of remote ports this is fixed.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Acked-by: James Bottomley <jejb@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Heiko Carstens <heiko.carstens@de.ibm.com>
Fixes module parameter parsing for "device" parameter. The original
module parameter was changed while parsing it. This corrupted the
output in sysfs (/sys/module/zfcp/parameters/device).
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes a race between zfcp_fsf_req_dismiss_all and
zfcp_qdio_reqid_check. During adapter shutdown it occurred that a
request was cleaned up twice. First during its normal
completion. Second when dismiss_all was called. The fix is to
serialize access to fsf request list between zfcp_fsf_req_dismiss_all
and zfcp_qdio_reqid_check and delete a fsf request from the list if
its completion is triggered. (Additionally a rwlock was replaced by a
spinlock and fsf_req_cleanup was eliminated.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Fixes a bug in zfcp_send_els_handler. If D_ID assignments for ports
are changing between initiation of one ELS request and its completion
the wrong port might be accessed in the completion for that ELS
request. Thus a pointer to the port has to be passed for ELS requests
to identify the port structure if required.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Correct a bug in zfcp_fsf_send_fcp_command_handler. An fsf request
was not marked as failed if an unknown status qualifier was returned.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Reopen a remote port only if the link-test fails. This avoids that a
port is unnecessarily reopened.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Extend the time for adapter initialization: In case of protocol
status HOST_CONNECTION_INITIALIZING for the exchange config data
command do a first retry in 1 second, then double the sleep time for
each following retry until recovery exceeds 2 minutes. The old
behaviour of allowing 6 retries with .5 seconds delay between retries
was insufficient and qdio queues were shut down too erarly.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes the handling of failed requests for GID_PN nameserver command:
Set ZFCP_STATUS_PORT_INVALID_WWPN only if indicated by response
payload for GID_PN nameserver command and not if fsf request fails.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Removes the rarely used "flags_dump" mechanism of zfcp.
Equivalent debug information will be provided with a reworking of
zfcp's s390dbf-facilities which is in preparation.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Andreas Herrmann <aherrman@de.ibm.com>
This patch mainly introduces support for point-2-point
topology.
From: Heiko Carstens <heiko.carstens@de.ibm.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
From: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
