Fix bnx2 so that netpoll works properly. Specifically:
1) Fix parameters to bnx2_interrupt to be a struct bnx2_napi rather than a
struct net_device
2) Fix poll_controller method to check every queue in the rx case so frames
aren't missed
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a TX hang reported by Jesper Dangaard Brouer.
When an architecutre cannot provide a fully functional
64-bit atomic readq/writeq, the driver must implement
it's own. This is because only the driver can say whether
doing something like using two 32-bit reads to implement
the full 64-bit read will actually work properly.
In particular one of the issues is whether the top 32-bits
or the bottom 32-bits of the 64-bit register should be read
first. There could be side effects, and in fact that is
exactly the problem here.
The TX_CS register has counters in the upper 32-bits and
state bits in the lower 32-bits. A read clears the state
bits.
We would read the counter half before the state bit half.
That first read would clear the state bits, and then the
driver thinks that no interrupts are pending because the
interrupt indication state bits are seen clear every time.
Fix this by reading the bottom half before the upper half.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like mac80211 did, this driver makes 'clever' use of skb->cb to pass
information along with an skb as it is requeued from the virtual device
to the physical wireless device. Unfortunately, that trick no longer
works...
Unlike mac80211, code complexity and driver apathy makes this hack
the best option we have in the short run. Hopefully someone will
eventually be motivated to code a proper fix before all the effected
hardware dies.
(Above text by me. Johannes officially disavows all knowledge of this
hack. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the Sitecom 0001 v4 with product id 0x0df6:0028, uses Realtek's
RTL8187B and work fine with new 2.6.27 driver.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I am trying out suspend, resume on an OMAP3 based board. What I see
during resume is that the SMC911x driver resume routing gets stuck
after trying to transmit the packet out of the controller. Some debug
messages below:
--> smc911x_drv_resume
eth0: --> smc911x_reset
eth0: smc911x_reset timeout waiting for PM restore
eth0: --> smc911x_enable
eth0: --> smc911x_phy_configure()
eth0: --> smc911x_phy_reset()
eth0: phy caps=0x782d
eth0: phy advertised caps=0x0de1
eth0: --> smc911x_phy_check_media
smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809
smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809
eth0: link down
Restarting tasks ... eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
nfs: server 172.24.190.217 not responding, still trying
nfs: server 172.24.190.217 not responding, still trying
The following change makes it work fine: (The change within
smc911x_drv_probe function was to get rid of a compilation warning).
Signed-off-by: Romit Dasgupta <romit@ti.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When the iw_cxgb3 module's cxgb3_client "add" func gets called by the
cxgb3 module, the iwarp driver ends up calling the ethtool ops get_drvinfo
function in cxgb3 to get the fw version and other info. Currently the
iwarp driver grabs the rtnl lock around this down call to serialize.
As of 2.6.27 or so, things changed such that the rtnl lock is held around
the call to the netdev driver open function. Also the cxgb3_client "add"
function doesn't get called if the device is down.
So, if you load cxgb3, then load iw_cxgb3, then ifconfig up the device,
the iw_cxgb3 add func gets called with the rtnl_lock held. If you
load cxgb3, ifconfig up the device, then load iw_cxgb3, the add func
gets called without the rtnl_lock held. The former causes the deadlock,
the latter does not.
In addition, there are iw_cxgb3 sysfs handlers that also can call
down into cxgb3 to gather the fw and hw versions. These can be called
concurrently on different processors and at any time. Thus we need to
push this serialization down in the cxgb3 driver get_drvinfo func.
The fix is to remove rtnl lock usage, and use a per-device lock in cxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Protect against invalid phy entries in the eeprom.
Extend eeprom access timeout.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The doorbell writes may be seen out of order by the firmware if they
are in WC memory since the tx spin(un)lock does not flush WC writes.
Hence if the "stop" is written on a different CPU than the "go", it
is possible that the stop will arrive after the go unless we add an
explicit memory barrier (and mmiowb() is not enough).
It fixes transmit hangs in multi tx queue mode.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Yup, this appears to be the problem, thanks. I think &hso_net->net->dev
is more intuitive for the error message, so I've used that. I've also
added missing line endings on the error messages and set our local
rfkill structure element to NULL on failure so we don't try to call
rfkill_unregister on driver removal if we failed to register at all.
The patch below Works For Me (TM); the device is detected fine, can be
removed without problems and connects ok. I'll have a prod at why the
rfkill stuff isn't working next, but I believe this cleanup of the error
handling is appropriate no matter what the issue with registration is.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to a hardware bug, the originally assigned range cannot reliably
be used for boot configuration and must not be modifiable through
ethtool.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tried to deactivate rx ring that wasn't activated,
used wrong index.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Fix recursive descent in __scm_destroy().
iwl3945: fix deadlock on suspend
iwl3945: do not send scan command if channel count zero
iwl3945: clear scanning bits upon failure
ath5k: correct handling of rx status fields
zd1211rw: Add 2 device IDs
Fix logic error in rfkill_check_duplicity
iwlagn: avoid sleep in softirq context
iwlwifi: clear scanning bits upon failure
Revert "ath5k: honor FIF_BCN_PRBRESP_PROMISC in STA mode"
tcp: Fix recvmsg MSG_PEEK influence of blocking behavior.
netfilter: netns ct: walk netns list under RTNL
ipv6: fix run pending DAD when interface becomes ready
net/9p: fix printk format warnings
net: fix packet socket delivery in rx irq handler
xfrm: Have af-specific init_tempsel() initialize family field of temporary selector
This patch fixes iwl3945 deadlock during suspend by moving notify_mac out
of iwl3945 mutex. This is a portion of the same fix for iwlwifi by Tomas.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ensures we clear any scan status bit when
an error occurs while sending the scan command. It is
the implementation of patch:
"iwlwifi: clear scanning bits upon failure"
for iwl3945.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_rx_status fields rs_antenna and rs_more are u8s, but we
were setting them with bitwise ANDs of 32-bit values.
As a consequence, jumbo frames would not be discarded as intended.
Then, because the hw rate value of such frames is zero, and, since
"ath5k: rates cleanup", we do not fall back to the basic rate, such
packets would trigger the following WARN_ON:
------------[ cut here ]------------
WARNING: at net/mac80211/rx.c:2192 __ieee80211_rx+0x4d/0x57e [mac80211]()
Modules linked in: ath5k af_packet sha256_generic aes_i586 aes_generic cbc loop i915 drm binfmt_misc acpi_cpufreq fan container nls_utf8 hfsplus dm_crypt dm_mod kvm_intel kvm fuse sbp2 snd_hda_intel snd_pcm_oss snd_pcm snd_mixer_oss snd_seq_dummy snd_seq_oss arc4 joydev hid_apple ecb snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device usbhid appletouch mac80211 sky2 snd ehci_hcd ohci1394 bitrev crc32 sr_mod cdrom rtc sg uhci_hcd snd_page_alloc cfg80211 ieee1394 thermal ac battery processor button evdev unix [last unloaded: ath5k]
Pid: 0, comm: swapper Tainted: G W 2.6.28-rc2-wl #14
Call Trace:
[<c0123d1e>] warn_on_slowpath+0x41/0x5b
[<c012005d>] ? sched_debug_show+0x31e/0x9c6
[<c012489f>] ? vprintk+0x369/0x389
[<c0309539>] ? _spin_unlock_irqrestore+0x54/0x58
[<c011cd8f>] ? try_to_wake_up+0x14f/0x15a
[<f81918cb>] __ieee80211_rx+0x4d/0x57e [mac80211]
[<f828872a>] ath5k_tasklet_rx+0x5a1/0x5e4 [ath5k]
[<c013b9cd>] ? clockevents_program_event+0xd4/0xe3
[<c01283a9>] tasklet_action+0x94/0xfd
[<c0127d19>] __do_softirq+0x8c/0x13e
[<c0127e04>] do_softirq+0x39/0x55
[<c0128082>] irq_exit+0x46/0x85
[<c010576c>] do_IRQ+0x9a/0xb2
[<c010461c>] common_interrupt+0x28/0x30
[<f80e934a>] ? acpi_idle_enter_bm+0x2ad/0x31b [processor]
[<c02976bf>] cpuidle_idle_call+0x65/0x9a
[<c010262c>] cpu_idle+0x76/0xa6
[<c02fb402>] rest_init+0x62/0x64
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
07fa/1196
Bewan BWIFI-USB54AR: Tested by night1308, this device is a ZD1211B with
an AL2230S radio.
0ace/b215
HP 802.11abg: Tested by Robert Philippe
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_tasklet_handler -> __ieee80211_rx ->
__ieee80211_rx_handle_packet -> ieee80211_invoke_rx_handlers ->
ieee80211_rx_h_decrypt -> ieee80211_crypto_tkip_decrypt ->
ieee80211_tkip_decrypt_data -> iwl4965_mac_update_tkip_key ->
iwl_scan_cancel_timeout -> msleep
Ooops!
Avoid the sleep by changing iwl_scan_cancel_timeout with
iwl_scan_cancel and simply returning on failure if the scan persists.
This will cause hardware decryption to fail and we'll handle a few more
frames with software decryption.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unfortunately, the result was that mac80211 didn't see all the beacons
it actually wanted to see. This caused lost associations.
Hopefully we can revisit this when mac80211 is less greedy about seeing
beacons directly...
This reverts commit 063279062a.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
xfrm: Fix xfrm_policy_gc_lock handling.
niu: Use pci_ioremap_bar().
bnx2x: Version Update
bnx2x: Calling netif_carrier_off at the end of the probe
bnx2x: PCI configuration bug on big-endian
bnx2x: Removing the PMF indication when unloading
mv643xx_eth: fix SMI bus access timeouts
net: kconfig cleanup
fs_enet: fix polling
XFRM: copy_to_user_kmaddress() reports local address twice
SMC91x: Fix compilation on some platforms.
udp: Fix the SNMP counter of UDP_MIB_INERRORS
udp: Fix the SNMP counter of UDP_MIB_INDATAGRAMS
drivers/net/smc911x.c: Fix lockdep warning on xmit.
netif_carrier_off was called too early at the probe. In case of failure
or simply bad timing, this can cause a fatal error since linkwatch_event
might run too soon.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code read nothing but zeros on big-endian (wrong part of the
32bits). This caused poor performance on big-endian machines. Though this
issue did not cause the system to crash, the performance is significantly
better with the fix so I view it as critical bug fix.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PMF flag is set, the driver can access the HW freely. When the
driver is unloaded, it should not access the HW. The problem caused fatal
errors when "ethtool -i" was called after the calling instance was unloaded
and another instance was already loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv643xx_eth mii bus implementation uses wait_event_timeout() to
wait for SMI completion interrupts.
If wait_event_timeout() would return zero, mv643xx_eth would conclude
that the SMI access timed out, but this is not necessarily true --
wait_event_timeout() can also return zero in the case where the SMI
completion interrupt did happen in time but where it took longer than
the requested timeout for the process performing the SMI access to be
scheduled again. This would lead to occasional SMI access timeouts
when the system would be under heavy load.
The fix is to ignore the return value of wait_event_timeout(), and
to re-check the SMI done bit after wait_event_timeout() returns to
determine whether or not the SMI access timed out.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The bool kconfig option added to ixgbe and myri10ge for DCA is ambigous,
so this patch adds a description to the kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This reverts 51ac3beffd ('SMC91x: delete
unused local variable "lp"') and adds __maybe_unused markers to these
(potentially) unused variables.
The issue is that in some configurations SMC_IO_SHIFT evaluates
to '(lp->io_shift)', but in some others it's plain '0'.
Based upon a build failure report from Manuel Lauss.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
af_unix: netns: fix problem of return value
IRDA: remove double inclusion of module.h
udp: multicast packets need to check namespace
net: add documentation for skb recycling
key: fix setkey(8) policy set breakage
bpa10x: free sk_buff with kfree_skb
xfrm: do not leak ESRCH to user space
net: Really remove all of LOOPBACK_TSO code.
netfilter: nf_conntrack_proto_gre: switch to register_pernet_gen_subsys()
netns: add register_pernet_gen_subsys/unregister_pernet_gen_subsys
net: delete excess kernel-doc notation
pppoe: Fix socket leak.
gianfar: Don't reset TBI<->SerDes link if it's already up
gianfar: Fix race in TBI/SerDes configuration
at91_ether: request/free GPIO for PHY interrupt
amd8111e: fix dma_free_coherent context
atl1: fix vlan tag regression
SMC91x: delete unused local variable "lp"
myri10ge: fix stop/go mmio ordering
bonding: fix panic when taking bond interface down before removing module
...
dev_kfree_skb should not be called with irqs disabled, use dev_kfree_skb_irq
instead. The warning caused looks like this:
======================================================
[ INFO: hard-safe -> hard-unsafe lock order detected ]
2.6.28-rc1 #273
------------------------------------------------------
swapper/0 [HC0[0]:SC1[2]:HE0:SE0] is trying to acquire:
(clock-AF_INET){-..+}, at: [<4015c17c>] _sock_def_write_space+0x28/0xd8
and this task is already holding:
(&lp->lock){++..}, at: [<4013f230>] _smc911x_hard_start_xmit+0x30/0x4b8
which would create a new lock dependency:
(&lp->lock){++..} -> (clock-AF_INET){-..+}
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As noticed by Saikiran Madugula, commit 7447ef63cf
("loopback: Remove rest of LOOPBACK_TSO code.") got rid of
emulate_large_send_offload() but didn't get rid of the call
site as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove excess kernel-doc function parameters from networking header
& driver files:
Warning(include/net/sock.h:946): Excess function parameter or struct member 'sk' description in 'sk_filter_release'
Warning(include/linux/netdevice.h:1545): Excess function parameter or struct member 'cpu' description in 'netif_tx_lock'
Warning(drivers/net/wan/z85230.c:712): Excess function parameter or struct member 'regs' description in 'z8530_interrupt'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move SKB trim before we lookup the socket so we don't have to
put it on failure.
Based upon an initial patch by Jarek Poplawski and suggestions
from Herbert Xu.
Signed-off-by: David S. Miller <davem@davemloft.net>
The link may be up already via the chip's reset strapping, or though action
of U-Boot, or from the last time the interface was brought up. Resetting
the link causes it to go down for several seconds. This can significantly
increase the time from power-on to DHCP completion and a device being
accessible to the network.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.
The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus. This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.
The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.
Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device. This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.
The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY. This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers. As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).
Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar. But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.
We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers. If one is found the ID of its platform device is saved in the
gianfar's platform data.
A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID. The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
