This adds support for probing the COH 901 318 DMA controller
and channels from the device tree.
Contains portions of a sketch patch from Arnd Bergmann.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the U300 MMC/SD card slot from the device
tree boot. No other changes needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have enabled board power and the AB3100 regulators,
put the regulator data into the device tree and enable it so
we can start to tie regulators to devices. To begin with we're
only supplying the power to the board itself.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for setting up the board power from the
device tree on the U300. We use a board-specific node in the
device tree for the S365 board and bind a regulator for the
board power to this node.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This add devicetree probe support to the COH 901 331 RTC
driver.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
WM8962 needs 24MHz clock for its MCLK, so choose PLL4 as the parent of clko1.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
These options are useful for controlling backlight contrast via PWM.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There are ulpi access ops implemented in drivers/usb/phy/phy-ulpi.c.
mxc access ops implement the same access operations within mach-imx. This
patch removes the mxc ulpi file and uses phy-ulpi instead for
imx_otg_ulpi_create.
phy-ulpi successfully tested with i.MX27 Phytec phyCARD-S (pca100).
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add clock support for Vybrid VF610. It uses dtc macro support to
define all clock IDs in vf610-clock.h to keep clock IDs coherence
between kernel and DT.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
commit 84344b43c (ARM: i.MX5: Allow DT clock providers) introduce the following
sparse warning:
arch/arm/mach-imx/clk.c:12:43: warning: Using plain integer as NULL pointer
There is no need to initialize phandle, so remove it.
Cc: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fix the following sparse warning:
arch/arm/mach-imx/irq-common.c:24:5: warning: symbol 'mxc_set_irq_fiq' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of explicitly calling clock initialization functions, we can
declare the functions with CLK_OF_DECLARE() and then call common
of_clk_init() to have them invoked properly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Let the mx53 TVE driver be built by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CCM_CBCMR register (address 0x02C4018) has different meaning
between the i.MX6 Quad/Dual and the i.MX6 Solo/DualLite.
Compared to the i.MX6 Quad/Dual, the CCM_CBCMR register in the
i.MX6 Solo/DualLite reuses the gpu2d_core bits for the MLB clock
configuration.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds the S/PDIF clocks for i.MX51 and i.MX53. Tested on i.MX53.
The i.MX51 has a second set of spdif_root clock dividers, and on i.MX53
there is an additional input to the spdif_xtal mux.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
MLB PLL should be handled internally in MLB driver,
so remove it from pllv3.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The MLB PLL clock's operation doesn't fit for clock framework and
it should be handled internally in MLB driver.
Remove initialization of pll8_mlb clock device but leave its
declaration in mx6q_clks to avoid affecting imx6q clock numbering.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add clock support for i.MX6 SoloLite. It uses the dtc marco support to
define all clock IDs in imx6sl-clock.h, which will be included by both
clock driver and device tree sources, so that the data will stay sync
all the time between kernel and DT.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The mxc_arch_reset_init() uses static mapping and calls clk_get_sys() to
get clock. It's suitable for non-DT boot but not for DT boot where
dynamic mapping and of_clk_get() should be used instead. Create
mxc_arch_reset_init_dt() as the DT variant of mxc_arch_reset_init(),
and change DT platforms to use it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's inappropriate to call clk_prepare() in mxc_restart(), because the
restart routine could be called in atomic context. Move clk_get() and
clk_prepare() into mxc_arch_reset_init() and only have the atomic part
clk_enable() be called in mxc_restart().
As a result, mxc_arch_reset_init() needs to be called after clk gets
initialized.
While there, it also changes printk(KERN_ERR ...) to pr_err() and adds
__init annotation for mxc_arch_reset_init().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CCM_CBCMR register (address 0x02C4018) has different meaning
between the i.MX6 Quad/Dual and the i.MX6 Solo/DualLite.
Compared to the i.MX6 Quad/Dual, the CCM_CBCMR register in the
i.MX6 Solo/DualLite doesn't have a gpu3d_shader configuration and
moves the gpu2_core configuration at that place.
Handle these i.MX6 Quad/Dual vs. i.MX6 Solo/DualLite clock differences
by using cpu_is_mx6dl().
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
To improve the performance and power consumption add an i.MX6
specific L2 cache initialization.
This configuration is taken from Freescale's kernel patch
"ENGR00153601 [MX6]Adjust L2 cache parameter" [1]
with two additional improvements:
a) The L2X0_POWER_CTRL has only the two bits we set. So no need
to read the register before. Remove the register read done
in Freescale's patch.
b) In the L2X0_PREFETCH_CTRL register, besides the double linefill (bit[30]),
additionally enable the instruction and data prefetch (bit[29-28]).
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[1] http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_12.09.01&id=814656410b40c67a10b25300e51b0477b2bb96d1
Currently clock providers defined in the DT are not registered
on i.MX5 platforms since of_clk_init() is not called.
This is not a problem for the SOC's own clocks, which are registered
in code, but prevents the DT being used to define clocks for external
hardware.
Fix this by calling of_clk_init() and actually using the DT to obtain
the 4 SOC fixed clocks.
These are already defined in the DT but were previously just used to
manually obtain the rate.
Fall back to the old scheme for non DT platforms.
Since the same method may be useful for other i.MX platforms
implement the imx_obtain_fixed_clock() function in common code.
Actually changing other i.MX platforms to use this should be done
later by someone with access to the appropriate hardware.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Remove board support for the r8a7740 based Bonito board
The r8a7740 SoC support code is still kept around since it
is in use by the Armadillo800eva board which is basically a more
recent board where the design is based on Bonito.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove board support for the sh7372 based AP4EVB board
The sh7372 SoC support code is still kept around since it
is in use by the Mackerel board which is basically a more
recent board where the design is based on AP4EVB.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove mach-shmobile memory.h since it is no longer needed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove CONFIG_MEMORY_START and CONFIG_MEMORY_SIZE from mach-shmobile.
Boards should use DT to specify their memory setup. Boards that still
not support DT may pass ATAGS with memory information from the boot
loader. If those ATAGS turn out to be incorrect then appended DTB with
memory information should be used as a workaround.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust mach-shmobile to add a select for CONFIG_ARM_PATCH_PHYS_VIRT
and at the same time remove NEED_MACH_MEMORY_H.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove shmobile_secondary_vector_scu now when all SCU enabled
SMP platforms instead make use of shmobile_boot_scu. This
removes two inline virtual to physical address conversions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Let EMEV2 make use of shmobile_boot_fn and shmobile_boot_arg
together with shmobile_boot_scu and the SCU base address.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Let sh73a0 make use of shmobile_boot_fn and shmobile_boot_arg
together with shmobile_boot_scu and the SCU base address.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Let r8a7779 make use of shmobile_boot_fn and shmobile_boot_arg
together with shmobile_boot_scu and the SCU base address.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a shmoible_boot_scu function that assumes that the base address
of the SCU is passed in r0. This code is free from inline virtual
to physical address conversion.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add code for mach-shmobile to allow specifying boot function
and argument. Will initially be used for SMP together with SCU
but may in the future also be used for deep sleep resume. This
patch removes one inline virtual to physical address conversion.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instead of having a hard coded virt-to-phys address
conversion code in sleep-sh7372.S, rework the code
to do the conversion in C using virt_to_phys().
This removes the need for PLAT_PHYS_OFFSET which
in turn is needed for ARCH_MULTIPLATFORM.
Signed-off-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: squashed in build fix posted as
"ARM: shmobile: sh7372 build fix for SUSPEND=n && CPU_IDLE=n"]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The A10s is a SoC member of the Allwinner sun5i family. It is basically
an A13 with an EMAC and an HDMI controller.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Another week, another batch of fixes for arm-soc platforms.
Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical since
it fixes a problem where multiplatform kernels panic on all but prima2
hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=c555
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"These are a little later than I planned on since I got caught up with
handling merges for 3.11 most of the week.
Another week, another batch of fixes for arm-soc platforms.
Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical
since it fixes a problem where multiplatform kernels panic on all but
prima2 hardware."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SAMSUNG: pm: Adjust for pinctrl- and DT-enabled platforms
ARM: prima2: fix incorrect panic usage
arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range
ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().
ARM: omap3: clock: fix wrong container_of in clock36xx.c
ARM: dts: OMAP5: Fix missing PWM capability to timer nodes
ARM: dts: omap4-panda|sdp: Fix mux for twl6030 IRQ pin and msecure line
ARM: dts: AM33xx: Fix properties on gpmc node
arm: omap2: fix AM33xx hwmod infos for UART2
ARM: OMAP3: Fix iva2_pwrdm settings for 3703
