Add support for the DMA blocks in the S3C64XX series of CPUS,
which are based on the ARM PL080 PrimeCell system.
Unfortunately, these DMA controllers diverge from the PL080
design by adding another DMA controller register and
configuration for OneNAND.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use the newly moved <plat/watchdog-reset.h> to perform the
arch_reset() call which has been unimplemented for a while.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix compilation bug when debug was enabled
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cleanup arm/plat-s3c64xx/include/plat/gpio-bank-h.h include file.
Using shift-left operation with value >32 is a bad habit.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add missing DMA controller block clocks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for S3C6400 SDHCI channels 0 and 1, making
the GPIO code common to both S3C6400 and S3C6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add detection support for the S3C6400 SoC which has it's
id register in a different place to the S3C6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add power management support to the VIC by registering
each VIC as a system device to get suspend/resume
events going.
Since the VIC registeration is done early, we need to
record the VICs in a static array which is used to add
the system devices later once the initcalls are run. This
means there is now a configuration value for the number
of VICs in the system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the GPIO suspend/resume support inline with the gpiolib support
so that it will work with both the S3C24XX and S3C64XX series.
The s3c_gpio_chip is extended to have a pm callback and a save block
to keep the state of the GPIO over suspend, and the code from the
s3c24xx implementation is added to a new common file.
The suspend process now uses the list of registered chips to go through
saving and restoring each one as appropriate, using the pm callback to
select the appropriate routine depending on the type of control register
present.
This change also means that any additional GPIO added should not require
changes to the PM.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for saving the state of the IRQ registers over suspend.
This requires moving the S3C64XX UART registers into <plat/regs-serial.h>
and adding irq-pm.c which saves the state of all the IRQ registers.
The irq-pm.c saves all the IRQ registers, including the IRQ_EINT and
IRQ_EINT_GROUP registers as it was easier than adding three different
files. Also ensuring that all the registers are restored to the same
state as before suspend is considered to be the best thing to do.
Note, we do not suspend the VIC here, this is done by the VIC driver
itself.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add an s3c64xx_sysclass and device for items that currently
want to bind to any s3c64xx processor. The first user of this
will be parts of the s3c64xx suspend support which need to
save device state over suspend/resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the initial support for the S3C64XX based systems to use
suspend-to-RAM to sleep.
Includes basic debugging for use with the SMDK6410 usign the
LEDs on the baseboard.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the register defines for the sleep and power control
functions in the S3C64XX SYSCON register block.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add definitions for the EINT group registers and move the EINT IRQ
register definitions out of arch/arm/plat-s3c64xx/irq-eint.c so that
they are available for re-use with PM and the other code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the modem registers and a virtual mapping for the
modem block. This is is required as there are registers
that control the LCD block that need to be saved over
suspend as well as interrupt controls.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some of the rate selection logic in s3c64xx_setrate_clksrc uses what
appears to be parent clock selection logic. This patch corrects it.
I also added a check for overly large dividers to prevent them from
changing unrelated clocks.
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warnings in s3c6400-clock.c:
39:12: warning: symbol 'clk_ext_xtal_mux' was not declared. Should it be static?
66:12: warning: symbol 'clk_fout_apll' was not declared. Should it be static?
81:19: warning: symbol 'clk_mout_apll' was not declared. Should it be static?
91:12: warning: symbol 'clk_fout_epll' was not declared. Should it be static?
106:19: warning: symbol 'clk_mout_epll' was not declared. Should it be static?
126:19: warning: symbol 'clk_mout_mpll' was not declared. Should it be static?
148:12: warning: symbol 'clk_dout_mpll' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clock list for the USB host bus clock was in the wrong order,
move clk_48m to position 0.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The USB OHCI host device expects the IRQ definition to be named
IRQ_USBH, so rename the S3C64XX IRQ header to match.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
arch_initcall() runs after the machine init function which means that
any configuration of GPIO pins must currently be done later on, for
example in callbacks from drivers. Move the initialisation earlier in
order to allow machines to configure GPIOs directly in their init
functions rather than having to have a callback invoked later on.
Some other ARM platforms use this method. Other solutions for this
include providing a special interface for setting up GPIOs en masse,
adding callbacks to do the GPIO configuration from devices and doing
the GPIO configuration implicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It's an initcall and does not need to be exported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Currently the unmask function for EINT interrupts was setting the mask
bit rather than clearing it. This was also previously reported and
fixed by Kyungmin Park <kyungmin.park@samsung.com> and others.
Acked-By: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix IRQ_EINT_GROUP which has an extra _ in it and
an error in the IRQ offset.
Signed-off-by: Matt Hsu <matt_hsu@openmoko.org>
[ben-linux@fluff.org: rewrite description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As per Russell King's last review comment, find and remove
all unnecessary includes of <linux/delay.h> in the files
that do not need them.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Select the correct EINT configuration register when configuring
the external interrupt level/edge type.
Signed-off-by: Matt Hsu <matt_hsu@openmoko.org>
[ben-linux@fluff.org: description improvement]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Correct the PLL field masks to ensure the PLL functions return the
right value.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[ben-linux@fluff.org: improve the description text]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C64XX timer is running at the wrong rate due to the
assumptions made in the timer initialisation about the way
the pwm dividers work. This means that time on the S3C64XX
runs twice as fast as it should.
Fix the problem by moving to using the clk framework to setup
the pwm timer clock muxes, as the pwm-clock code has all the
necessary knowledge of how the timer clock inputs are routed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add device definition and support functions for the
second i2c device (i2c1). If this is selected, the first
i2c bus will become index 0 instead of index -1.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_fout_epll clock wasn't registered as part of the initial clock
work, which can cause problems if it is used by one of the hardware
blocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The gpiolib driver keeps its chip array to itself
and having a separate array for s3c-only gpios stops
any non-s3c gpio being used in one of the s3c specific
configuration calls.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add definitions for the external interrupt groups which accompany
the original IRQ_EINT from the s3c24xx series.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Discard the 'void *' from the pointers used for the
virtual addresses when setting up the .virtual fields
of the io map to avoid implicit cast warnings
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Index: linux.git/arch/arm/plat-s3c64xx/cpu.c
===================================================================
Some of the startup output can be reduced to
KERN_DEBUG from KERN_INFO as it is only really
useful when trying to debug kernel initialisation
problems.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the necessary code to support IRQ_EINT(x) on
the S3C64XX series of CPUs.
Note, since there is no GPIO configuration support
in the kernel, the irq set_type method does not
configure the relevant pin to interrupt.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add demux handling for the UART interrupts
generated by the VIC into their seperate IRQs
that the serial driver can register.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the PLL clock initialisation and clock registration
and include the clocks sourced via CLKDIVx for most of
the on-chip peripherals.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the initial clocks definitions for the s3c6400
and s3c6410. Move the epll and ext clock from the
s3c2443 support into the common code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the physical to virtual memory mapping and the
necessary interrupt demuxing for the PWM timer blocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Initialise the basic physical to virtual mappings and
then detect the CPU that the system is being run on so
that the cpu code code can call the correct initialisation
code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the initial header files for the S3C64XX support to satisfy the
minimal requirements to build a kernel. Some definitions will therefore
be placeholders or empty functions that will ensure that the system can
build and have base functionality. These will be filled in at a later
date.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
