Having the device detection happening at reset is bad, as every time,
it will produce a message like:
tvp5150 2-005c: tvp5150am1 detected.
This only polutes the log and for an accidental kernel hacker, it looks
like a real problem. So, move those printk's to happen during device
probe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When digitizing composite video from a analog videotape source using the
TVP5150's first composite input channel, the captured stream exhibits
tearing and synchronization problems[1].
It turns out that commit c0477ad9fe caused
"TV mode" (as opposed to "VCR mode" or "auto-detect") to be forcibly
enabled for both composite inputs. According to the chip
documentation[2], "TV mode" disables a "chrominance trap" input filter,
which appears to be necessary for high-quality video capture from an
analog videotape source. [ Commit
c7c0b34c27 subsequently restricted the
problem to the first composite input, apparently inadvertently. ]
Since any type of composite signal source can be connected to the
TVP5150's first composite input, unconditionally forcing "TV mode" isn't
correct. There doesn't appear to be a good way for applications to tell
the driver what is connected. Fortunately, the TVP5150 has an operating
mode auto-detection feature, which, when enabled, should cause the TVP5150
to auto-detect whether it should use "VCR mode" or "TV mode". Enabling
operating mode auto-detection improved video capture quality
significantly[3].
Therefore, fix this bug by using operating mode auto-detection. (Also,
while here, fix a CodingStyle issue.)
For those users who may find this patch via a mailing list archive but who
are not able to upgrade to a kernel with a fixed driver: the TVP5150's
S-Video and second composite input sources have auto-detection enabled, so
you may wish to try using those -- if available on your device -- until
this fix makes it a downstream distribution near you.
1. Pre-patch tvtime snapshot using a Pinnacle PCTV HD Pro as the
capture device and a Sony EV-S2000 as a video source:
http://www.booyaka.com/~paul/tvp5150/1a.png
2. Section 3.21.3, "Operation Mode Control Register", _TVP5150AM1
Ultralow-Power NTSC/PAL/SECAM Video Decoder (Rev. D)_ [SLES209D],
downloaded 8 October 2010, available via
http://focus.ti.com/lit/ds/symlink/tvp5150am1.pdf
3. Post-patch tvtime snapshot (same signal chain as #1, above):
http://www.booyaka.com/~paul/tvp5150/1b.png
Signed-off-by: Paul Walmsley <paul@booyaka.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that s_fmt is no longer used for VBI format setup in subdevs, remove
the VBI support from s_fmt.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only a relatively small number of video receivers and transmitters actually
support VBI. So start moving the vbi specific ops to an ops struct of their
own.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
It is no longer needed to use a struct pointer as argument, since v4l2_subdev
doesn't require that ioctl-like approach anymore. Instead just pass the input,
output and config (new!) arguments directly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_std didn't belong in the tuner ops. Stricly speaking it should be part of
the video ops, but it is used by audio and tuner devices as well, so it is
more efficient to make it part of the core ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers that use tvp5150 now use v4l2_subdev, so we can remove the
legacy code from tvp5150.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace 'VIDIOC_' references in v4l i2c drivers by their new v4l2_subdev
callback names.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, just a few modules are still dependent of this legacy header:
$ grep -l DECODER_ `find linux/drivers/media/ -name '*.[ch]' -exec grep -l video_decoder '{}' \;`
linux/drivers/media/video/v4l2-ioctl.c
linux/drivers/media/video/indycam.c
linux/drivers/media/video/saa7191.c
linux/drivers/media/video/vino.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C_DRIVERIDs are phased out. Remove those that are unused at the moment.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the i2c driver ID will be removed in the near future we have to
modify the v4l2 debugging API to use the driver name instead of driver ID.
Note that this API is not used in applications other than v4l2-dbg.cpp
as it is for debugging and testing only.
Should anyone use the old VIDIOC_G_CHIP_IDENT, then this will be logged
with a warning that it is deprecated and will be removed in 2.6.30.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several V4L2 drivers still included videodev.h. Fix this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Static memory is always initialized with 0.
- Replaced in some cases C99 comments for /* */
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The chip matching in struct v4l2_register for VIDIOC_DBG_G/S_REGISTER
was rather primitive. It could not be extended to other busses besides
i2c and it lacked a way to.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before, root privileges were only needed to set hardware registers, not
to read them. On some hardware, reading from the wrong place at the
wrong time can hang the machine. So, to be consistent, root privileges
are required to read registers on all hardware.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The direct register access ioctls were defined as kernel internal only,
but they are very useful for debugging hardware from userspace and are
used as such. Officially export them.
VIDIOC_INT_[SG]_REGISTER is renamed to VIDIOC_DBG_[SG]_REGISTER
Definition of ioctl and struct v4l2_register is moved from v4l2-common.h
to videodev2.h.
Types used in struct v4l2_register are changed to the userspace
exportable versions (u32 -> __u32, etc).
Use of VIDIOC_DBG_S_REGISTER requires CAP_SYS_ADMIN permission, so move
the check into the video_ioctl2() dispatcher so it doesn't need to be
duplicated in each driver's call-back function. CAP_SYS_ADMIN check is
added to pvrusb2 (which doesn't use video_ioctl2).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Use new routing input defines in em28xx-cards.c
- Fix S-Video settings for tvp5150-based cards (input was copied from saa7115
based cards and worked only because S-Video was selected in the default: case)
- Replace VIDIOC_S_INPUT by VIDIOC_INT_S_VIDEO_ROUTING in em28xx-video.c
- Remove the now obsolete VIDIOC_S_INPUT handler in saa7115.c
- Add VIDIOC_INT_G/S_VIDEO_ROUTING in tvp5150.c
- Add new media/tvp5150.h with the routing defines.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Remove old DECODER_ commands from tvp5150.c, replacing them with newer
ones if appropriate.
- Small VIDIOC_G_TUNER fixes in msp3400 and tuner.
- Fix VIDIOC_S_TUNER support in em28xx.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The sliced VBI defines added in videodev2.h are removed since requires
more discussion.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
disabled debug on by default in tvp5150
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- added signal detection support to tvp5150
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added other sliced VBI types to videodev2.h
- tvp5150 now uses standard V4L2 API codes from videodev2.h
- Implemented VIDIOC_G_SLICED_VBI_CAP for tvp5150. This is
dynamically filled based on defined VDP C-RAM values filled
by the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Renamed some registers and improved register debug message
- Some cleanups at register dump
- Added code to set VBI processor (VDP)
- VBI code still incomplete
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Tvp5150 type were determined by a secondary register instead of
using ROM code.
- tvp5150am1 have ROM=4.0, while tvp5150a have ROM=3.33 (decimal).
All other ROM versions are reported as unknown tvp5150.
- Except for reporting, current code doesn't enable any special feature
for tvp5150am1 or tvp5150a. Code should work for both models (but were
tested only for tvp5150am1).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- This patch makes some needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Included advanced debug option to tvp5150.c
- Now, advanced debug info is the first item at V4L menu.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Now reset do init tvp5150 registers to its default.
- Debug messages improved.
- Implemented video standard selection function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Controls now come from video and audio decoder driver for msp3400 and tvp5150.
- Added audio and sound controls as provided by msp3400 and tvp5150.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
