Now that we have kvfree, use it in vhost-scsi instead of
the open-coded version.
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 23cc5a991c ("vhost-net: extend device allocation to vmalloc")
added another open-coded version of kvfree (which is available since
v3.15-rc5), nuke it.
Signed-off-by: Romain Francoise <romain@orebokech.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes commit 3be2a49e5c ("of: provide a binding for fixed link PHYs")
Fix the parsing of the new fixed link dts bindings for duplex,
pause, and asym_pause by using the correct device node pointer.
Signed-off-by: Richard Retanubun <rretanubun.work@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Varka Bhadram says:
====================
Driver for TI CC2520 Radio
changes since v6:
- proper releasing of resources
- changed pr_debug() to dev_dbg()
- removed unwanted header file
- changed is_tx type to bool
changes since v5:
- added saddr and panc_changed functionality
- rework on lqi field
- improvements in checkings for reception
- modification in debug messages
changes since v4:
- feature to write into cc2520 RAM
- added h/w address filtering
changes since v3:
- drop the unused varible
changes since v2:
- drop spi mode dt binding
changes since v1:
- improvement in gpio setup
- changed len pointer to len variable
changes for v1:
- improvements in the locking mechanism in Tx and SFD ISR
- proper checkings for GPIO pins
- avoids the memory leak for priv
- used devm_* API's
- moved the code from header file to .c file
- removed cc2520_unregister()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver support for the cc2520 radio.
Driver support:
- Tx and Rx of IEEE-802.15.4 packets
- Energy Detection on channel
- Setting the Channel for the radio. [b/w 11 - 26 channels]
- Start and Stop the radio
- h/w address filtering
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anish Bhatt says:
====================
cxgb4 : Add DCBx support to Chelsio cxgb4 driver
This patchset adds support for DCBx via dcbnl_ops to the cxgb4
driver. This should enable cxgb4 to work with open-lldp and the
like. The last patch only updates copyright year.
v2 : move inclusion of struct port_dcb_info to the same patch as where it is defined.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8eba0eefae ("at86rf230: remove irq_type in
request_irq") removed the trigger configuration when requesting an irq,
and instead relied on the interrupt trigger to be properly configured
already. This does not seem to be an assumption that can be safely made,
since boards disable all interrupt triggers on boot.
On these boards, force the irq to trigger on rising edge, which is also
the default for the chip.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/phy/at803x.c:196:26-32: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The time comparsion functions require arguments of type unsigned long
instead of (signed) long.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Single ported VF are currently not supported on configurations where
one or both ports are IB. When we hit this case, the relevant flow in
the driver didn't return error and jumped to the wrong label. Fix that.
Fixes: dd41cc3 ('net/mlx4: Adapt num_vfs/probed_vf params for single port VF')
Reported-by: Shirley Ma <shirley.ma@oracle.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It now takes up to 60 seconds to detect cable (un)plug on ADMtek Comet chips.
That's too slow and might cause people to think that it doesn't work at all.
Poll link status every 2 seconds instead of 60 for ADMtek Comet chips.
That should be fast enough while not stressing the system too much.
Tested with ADMtek AN983B.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3Mlm
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge Samsung fixes for 3.16 from Kukjin Kim:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
ARM: EXYNOS: fix pm code to check for cortex A9 rather than the SoC
clocksource: exynos_mct: Don't reset the counter during boot and resume
ARM: dts: fix reg sizes of GIC for exynos4
ARM: EXYNOS: Use wfi macro in platform_do_lowpower
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull i2c new drivers from Wolfram Sang:
"Here is a pull request from i2c hoping for the "new driver" rule.
Originally, I wanted to send this request during the merge window, but
code checkers with very recent additions complained, so a few fixups
were needed. So, some more time went by and I merged rc1 to get a
stable base"
So the "new driver" rule is really about drivers that people absolutely
need for the kernel to work on new hardware, which is not so much the
case for i2c. So I considered not pulling this, but eventually
relented.
Just for FYI: the whole (and only) point of "new drivers" is not that
new drivers cannot regress things (they can, and they have - by
triggering badly tested code on machines that never triggered that code
before), but because they can bring to life machines that otherwise
wouldn't be useful at all without the drivers.
So the new driver rule is for essential things that actual consumers
would care about, ie devices like networking or disk drivers that matter
to normal people (not server people - they run old kernels anyway, so
mainlining new drivers is irrelevant for them).
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sun6-p2wi: fix call to snprintf
i2c: rk3x: add NULL entry to the end of_device_id array
i2c: sun6i-p2wi: use proper return value in probe
i2c: sunxi: add P2WI (Push/Pull 2 Wire Interface) controller support
i2c: sunxi: add P2WI DT bindings documentation
i2c: rk3x: add driver for Rockchip RK3xxx SoC I2C adapter
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTpiwZAAoJEAAOaEEZVoIVplsP/383a9q3eXonbsi+Ea8CGbRl
tdjjVhM1OY4NZYFAoulILDt3HqPTC6MBnqKlHz+BuMziwd/1+3w8S4E7IEwm/KtM
ghNYX8ct5Bf1nc5QEdDmwf4PX48QbRwTuT1uIcXaJ+KtxTzI9qN7mnjRN91TUtq4
WRGvOl0AsGCVq8YqxjztgD3TYbu7AG/72Em+DE9f81PTArAPTo2ySc3gxPuJJAsg
G1x46Gx46sfqFX2FY4SPsXen+J/67Og67y6eBawxnT2Bp6ZGDuW+jyPRmkhf0yth
pWAtkUi3XmEe6kk6GHiICsS0Yn0RG4jbz39+Ja+X7jibQVJ8Iz6b+Optw9RNQwYt
jDWHKFS2AaL/CDejHYOQ1shHcozpRojtIbDLIZ9vTNTQ2r5cdaBvkXMmQzdoktmN
wQtQ9AzBl8fHOFOQeCAwd/ZfCLIotvLoLds3K/CSqmpsyK2+9IyriQLKKZ2xm6Iu
8+UUspGQcNVwcMP6YWtI6G+u58/mVanmK6dtpiyXrncZLAfU4H7ETL2IPu8jJTbv
kTFCOJtXQzNZa5Xqur1hIewOG9/RlvAZAnii0Ghc3nXTWCCeNeI8re3jw4g9KdRv
33t4sYfJld8LQ1NSMqIDyAs+fvytmGurYt+uhVpb58G/4CqBLNpmmIGIQ6LFLMfs
75FQnbAezrD0H/JyAHUk
=AJD3
-----END PGP SIGNATURE-----
Merge tag 'locks-v3.16-2' of git://git.samba.org/jlayton/linux
Pull file locking fixes from Jeff Layton:
"File locking related bugfixes
Nothing too earth-shattering here. A fix for a potential regression
due to a patch in pile #1, and the addition of a memory barrier to
prevent a race condition between break_deleg and generic_add_lease"
* tag 'locks-v3.16-2' of git://git.samba.org/jlayton/linux:
locks: set fl_owner for leases back to current->files
locks: add missing memory barrier in break_deleg
Pull kbuild fixes from Michal Marek:
"There are three fixes for regressions caused by the relative paths
series: deb-pkg, tar-pkg and *docs did not work with O=.
Plus, there is a fix for the linux-headers deb package and a fixed
typo. These are not regression fixes but are safe enough"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: fix a typo in a kbuild document
builddeb: fix missing headers in linux-headers package
Documentation: Fix DocBook build with relative $(srctree)
kbuild: Fix tar-pkg with relative $(objtree)
deb-pkg: Fix for relative paths
Messages from the modem exceeding 256 bytes cause communication
failure.
The WDM protocol is strictly "read on demand", meaning that we only
poll for unread data after receiving a notification from the modem.
Since we have no way to know how much data the modem has to send,
we must make sure that the buffer we provide is "big enough".
Message truncation does not work. Truncated messages are left unread
until the modem has another message to send. Which often won't
happen until the userspace application has given up waiting for the
final part of the last message, and therefore sends another command.
With a proper CDC WDM function there is a descriptor telling us
which buffer size the modem uses. But with this vendor specific
implementation there is no known way to calculate the exact "big
enough" number. It is an unknown property of the modem firmware.
Experience has shown that 256 is too small. The discussion of
this failure ended up concluding that 512 might be too small as
well. So 1024 seems like a reasonable value for now.
Fixes: 41c47d8cfd ("net: huawei_cdc_ncm: Introduce the huawei_cdc_ncm driver")
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull btrfs fixes from Chris Mason:
"This fixes some lockups in btrfs reported with rc1. It probably has
some performance impact because it is backing off our spinning locks
more often and switching to a blocking lock. I'll be able to nail
that down next week, but for now I want to get the lockups taken care
of.
Otherwise some more stack reduction and assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix wrong error handle when the device is missing or is not writeable
Btrfs: fix deadlock when mounting a degraded fs
Btrfs: use bio_endio_nodec instead of open code
Btrfs: fix NULL pointer crash when running balance and scrub concurrently
btrfs: Skip scrubbing removed chunks to avoid -ENOENT.
Btrfs: fix broken free space cache after the system crashed
Btrfs: make free space cache write out functions more readable
Btrfs: remove unused wait queue in struct extent_buffer
Btrfs: fix deadlocks with trylock on tree nodes
Pull nfsd bugfixes from Bruce Fields:
"Fixes for a new regression from the xdr encoding rewrite, and a
delegation problem we've had for a while (made somewhat more annoying
by the vfs delegation support added in 3.13)"
* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
NFSD: fix bug for readdir of pseudofs
NFSD: Don't hand out delegations for 30 seconds after recalling them.
In commit 629c9a8fd0 (drivers: net: cpsw: Add
default vlan for dual emac case also), api cpsw_add_default_vlan() also
changes the port vlan which is required to seperate the ports which results
in the following behavior
In Dual EMAC mode, when both the Etnernet connected is connected to same
switch, it creates a loop in the switch and when a broadcast packet is
received it is forwarded to the other port which stalls the whole switch
and needs a reset/power cycle to the switch to recover. So intead of using
the api, add only the default VLAN entry in dual EMAC case.
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Vrabel says:
====================
xen-netfront: fix resume regressions in 3.16-rc1
The introduction of multi-queue support to xen-netfront in 3.16-rc1,
broke resume/migration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When reconnecting to the backend (after a resume/migration, for example),
a different number of queues may be required (since the guest may have
moved to a different host with different capabilities). During the
reconnection the old queues are torn down and new ones created.
Introduce xennet_create_queues() and xennet_destroy_queues() that fixes
three bugs during the reconnection.
- The old info->queues was leaked.
- The old queue's napi instances were not deleted.
- The new queue's napi instances were left disabled (which meant no
packets could be received).
The xennet_destroy_queues() calls is deferred until the reconnection
instead of the disconnection (in xennet_disconnect_backend()) because
napi_disable() might sleep.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xennet_disconnect_backend() was not correctly iterating over all the
queues.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack says:
====================
Handle stuck TX queue bug in AT8030 PHY
These three small patches circument a hardware bug in AT8030 PHYs that
leads to stuck TX FIFO queues when the link goes away while there are
pending patches in der outbound queue. This bug has been confirmed by
the vendor, and their only proposed fix is to apply a hardware reset
every time the link goes down.
v1 -> v2:
* Rename phy device callback from adjust_state to link_change_notify
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT8030 will enter a FIFO error mode if a packet is transmitted while
the cable is unplugged. This hardware issue is acknowledged by the
vendor, and the only proposed solution is to conduct a hardware reset
via the external pin each time the link goes down. There is apparantly
no way to fix up the state via the register set.
This patch adds support for reading a 'reset-gpios' property from the DT
node of the PHY. If present, this gpio is used to apply a hardware reset
each time a 'link down' condition is detected. All relevant registers
are read out before, and written back after the reset cycle.
Doing this every time the link goes down might seem like overkill, but
there is unfortunately no way of figuring out whether the PHY is in
such a lock-up state. Hence, this is the only way of reliably fixing up
things.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes magic values from two tables and also allows us to match
against specific PHY models at runtime.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a notify callback to inform phy drivers when the core is about to
do its link adjustment. No change for drivers that do not implement
this callback.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_ematch is allocated by kzalloc in function tcf_em_tree_validate(),
so cm_old is always NULL.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use list_for_each_entry_continue_reverse to rollback in fdb_add_hw
when add address failed
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_cow called in vlan_reorder_header does not free the skb when it failed,
and vlan_reorder_header returns NULL to reset original skb when it is called
in vlan_untag, lead to a memory leak.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-06-20
This series contains updates to i40e and i40evf.
Anjali provides an update to the registers to handle the updates from the
hardware. Also provides a fix so that we do not try to access the rings
through the qvectors at the time of freeing the qvectors.
Jesse provides a workaround for some older NVM versions where the NVM
was not filling in the GLQF_HKEY register, so made sure that the
critical register is initialized.
Michal provides a fix to reset the head and tail on admin queue
initialization where head and tail are not reset by the hardware.
Neerav adds a helper routine that would wait for the Rx/Tx queue to reach
the enable or disable state that is requested. Also provides a fix
to the debugfs command "lldp get remote" which was dumping the local
LLDPDU instead of the peer's LLDPDU. Fixed a bug when all the Tx hang
recovery mechanisms have failed and the driver tries to bring down the
interface in the interrupt context.
Shannon provides a patch to clear the Virtual Ethernet Bridge (VEB) stats
when the PF stats are cleared. Also cleans the service tasks so that
they do not run while a reset is in progress.
Mitch fixes an issue in i40evf_get_rxfh() where only fifteen registers
were being read instead of all sixteen.
Carolyn provides a change to the RSS configuration to set table size and
write to the hardware to confirm the RSS table size being used.
Kamil makes a change to the admin queue debug prints so that they will not
cause segmentation faults in some of our tool applications.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull perf fixes from Ingo Molnar:
"This is larger than usual: the main reason are the ARM symbol lookup
speedups that came in late and were hard to resist.
There's also a kprobes fix and various tooling fixes, plus the minimal
re-enablement of the mmap2 support interface"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/kprobes: Fix build errors and blacklist context_track_user
perf tests: Add test for closing dso objects on EMFILE error
perf tests: Add test for caching dso file descriptors
perf tests: Allow reuse of test_file function
perf tests: Spawn child for each test
perf tools: Add dso__data_* interface descriptons
perf tools: Allow to close dso fd in case of open failure
perf tools: Add file size check and factor dso__data_read_offset
perf tools: Cache dso data file descriptor
perf tools: Add global count of opened dso objects
perf tools: Add global list of opened dso objects
perf tools: Add data_fd into dso object
perf tools: Separate dso data related variables
perf tools: Cache register accesses for unwind processing
perf record: Fix to honor user freq/interval properly
perf timechart: Reflow documentation
perf probe: Improve error messages in --line option
perf probe: Improve an error message of perf probe --vars mode
perf probe: Show error code and description in verbose mode
perf probe: Improve error message for unknown member of data structure
...
Pull rtmutex fixes from Thomas Gleixner:
"Another three patches to make the rtmutex code more robust. That's
the last urgent fallout from the big futex/rtmutex investigation"
* 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rtmutex: Plug slow unlock race
rtmutex: Detect changes in the pi lock chain
rtmutex: Handle deadlock detection smarter
Pull s390 patches from Martin Schwidefsky:
"A couple of bug fixes, a debug change for qdio, an update for the
default config, and one small extension.
The watchdog module based on diagnose 0x288 is converted to the
watchdog API and it now works under LPAR as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ccwgroup: use ccwgroup_ungroup wrapper
s390/ccwgroup: fix an uninitialized return code
s390/ccwgroup: obtain extra reference for asynchronous processing
qdio: Keep device-specific dbf entries
s390/compat: correct ucontext layout for high gprs
s390/cio: set device name as early as possible
s390: update default configuration
s390: avoid format strings leaking into names
s390/airq: silence lockdep warning
s390/watchdog: add support for LPAR operation (diag288)
s390/watchdog: use watchdog API
s390/sclp_vt220: Enable ASCII console per default
s390/qdio: replace shift loop by ilog2
s390/cio: silence lockdep warning
s390/uaccess: always load the kernel ASCE after task switch
s390/ap_bus: Make modules parameters visible in sysfs
Here are 3 patches, one a revert of the UIO patch you objected to in
3.16-rc1 and that no one wanted to defend, a w1 driver bugfix, and a
MAINTAINERS update for the vmware balloon driver. All of these, except
for the MAINTAINERS update which just got added, have been in linux-next just
fine.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlOkkTEACgkQMUfUDdst+ynIKACgxyvwXygqwiKaNutDvwrP9l+e
3joAn0gW1wVUq+7r/msb7sWosuNF9S2F
=kc9k
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver fixes from Greg KH:
"Here are 3 patches, one a revert of the UIO patch you objected to in
3.16-rc1 and that no one wanted to defend, a w1 driver bugfix, and a
MAINTAINERS update for the vmware balloon driver.
All of these, except for the MAINTAINERS update which just got added,
have been in linux-next just fine"
* tag 'char-misc-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: add entry for VMware Balloon driver
w1: mxc_w1: Fix incorrect "presence" status
Revert "uio: fix vma io range check in mmap"
Here are a few fixes for staging and iio drivers that resolve issues
reported in 3.16-rc1.
All have been in linux-next just fine.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlOkj58ACgkQMUfUDdst+ykg8QCfdKDeHmeZI2TEUadR460FJy4c
B5IAnAsLSIL/KPhLGjC5f1Ored6ESXal
=Ml7O
-----END PGP SIGNATURE-----
Merge tag 'staging-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few fixes for staging and iio drivers that resolve issues
reported in 3.16-rc1.
All have been in linux-next just fine"
* tag 'staging-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
imx-drm: parallel-display: Fix DPMS default state.
staging: android: timed_output: fix use after free of dev
staging: comedi: addi_apci_1564: add addi_watchdog dependency
staging: rtl8723au: Reference correct firmwarefiles with MODULE_FIRMWARE()
staging: rtl8723au: Request correct firmware file for A-cut parts
iio: adc: checking for NULL instead of IS_ERR() in probe
iio: adc: at91: signedness bug in at91_adc_get_trigger_value_by_name()
iio: mxs-lradc: fix divider
iio: Fix endianness issue in ak8975_read_axis()
staging/iio: IIO_SIMPLE_DUMMY_BUFFER neds IIO_BUFFER
twl4030-madc: Request processed values in twl4030_get_madc_conversion
staging: iio: tsl2x7x_core: fix proximity treshold
iio: Fix two mpl3115 issues in measurement conversion
iio: hid-sensors: Get feature report from sensor hub after changing power state
Here are some tty / serial driver bugfixes for 3.16-rc2 that resolve
some reported issues. The samsung driver build error itself has been
reported by a bunch of people, sorry about that one. The others are all
tiny and everyone seems to like them in linux-next so far.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlOkkKQACgkQMUfUDdst+ymZbwCgt1mJsOte0uOmb/bzDkJiM4mX
JuYAn3BF53FY50Y/bY1cVpcSDCbwFPdp
=gugC
-----END PGP SIGNATURE-----
Merge tag 'tty-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial bugfixes from Greg KH:
"Here are some tty / serial driver bugfixes for 3.16-rc2 that resolve
some reported issues. The samsung driver build error itself has been
reported by a bunch of people, sorry about that one. The others are
all tiny and everyone seems to like them in linux-next so far"
* tag 'tty-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty/serial: fix 8250 early console option passing to regular console
tty: Correct INPCK handling
serial: Fix IGNBRK handling
serial: samsung: Fix build error
Here are some USB fixes for 3.16-rc2 that resolve some reported issues.
All of these have been in linux-next for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlOkkZcACgkQMUfUDdst+ykfMQCfS3ANqdOu7FFfdnnzYLbQRiFP
RGUAn0/x1x6CGD5HKHWRE9NnmpZImGgU
=+3+c
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.16-rc2 that resolve some reported
issues. All of these have been in linux-next for a while with no
problems"
* tag 'usb-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbtest: add a timeout for scatter-gather tests
USB: EHCI: avoid BIOS handover on the HASEE E200
usb: fix hub-port pm_runtime_enable() vs runtime pm transitions
usb: quiet peer failure warning, disable poweroff
usb: improve "not suspended yet" message in hub_suspend()
xhci: Fix sleeping with IRQs disabled in xhci_stop_device()
usb: fix ->update_hub_device() vs hdev->maxchild
On exynos mcpm systems the firmware is hardcoded to jump to an address
in SRAM (0x02073000) when secondary CPUs come up. By default the
firmware puts a bunch of code at that location. That code expects the
kernel to fill in a few slots with addresses that it uses to jump back
to the kernel's entry point for secondary CPUs.
Originally (on prerelease hardware) this firmware code contained a
bunch of workarounds to deal with boot ROM bugs. However on all
shipped hardware we simply use this code to redirect to a kernel
function for bringing up the CPUs.
Let's stop relying on the code provided by the bootloader and just
plumb in our own (simple) code jump to the kernel. This has the nice
benefit of fixing problems due to the fact that older bootloaders
(like the one shipped on the Samsung Chromebook 2) might have put
slightly different code into this location.
Once suspend/resume is implemented for systems using exynos-mcpm we'll
need to make sure we reinstall our fixed up code after resume. ...but
that's not anything new since IRAM (and thus the address of the
mcpm_entry_point) is lost across suspend/resume anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The following commit:
89d7e5c mmc: sdhci-esdhc-imx: add runtime pm support
has the effect of also disabling the hardware card detect
in runtime pm.
We switch to GPIO based detection to avoid this issue.
This patch is based on:
ARM: dts: imx51-babbage: Fix esdhc setup
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since commit 89d7e5c131 (mmc: sdhci-esdhc-imx: add runtime pm
support), controller based card detection / write protection is not
supported anymore by esdhc driver. Let's use GPIO for CD/WP on esdhc1
instead.
While at it, fix cd gpio polarity for esdhc2. This is wrong and
currently only works because the imx esdhc driver ignores the polarity.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Move the display {} node out of the soc {} node . This just aligns
the DT with other boards, there is no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
