Actually better than brctl showmacs because we can filter by bridge
port in the kernel.
The current bridge netlink interface doesnt scale when you have many
bridges each with large fdbs or even bridges with many bridge ports
And now for the science non-fiction novel you have all been
waiting for..
//lets see what bridge ports we have
root@moja-1:/configs/may30-iprt/bridge# ./bridge link show
8: eth1 state DOWN : <BROADCAST,MULTICAST> mtu 1500 master br0 state
disabled priority 32 cost 19
17: sw1-p1 state DOWN : <BROADCAST,NOARP> mtu 1500 master br0 state
disabled priority 32 cost 100
// show all..
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show
33:33:00:00:00:01 dev bond0 self permanent
33:33:00:00:00:01 dev dummy0 self permanent
33:33:00:00:00:01 dev ifb0 self permanent
33:33:00:00:00:01 dev ifb1 self permanent
33:33:00:00:00:01 dev eth0 self permanent
01:00:5e:00:00:01 dev eth0 self permanent
33:33:ff:22:01:01 dev eth0 self permanent
02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:07 dev eth1 self permanent
33:33:00:00:00:01 dev eth1 self permanent
33:33:00:00:00:01 dev gretap0 self permanent
da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent
33:33:00:00:00:01 dev sw1-p1 self permanent
//filter by bridge
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br br0
02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:07 dev eth1 self permanent
33:33:00:00:00:01 dev eth1 self permanent
da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent
33:33:00:00:00:01 dev sw1-p1 self permanent
// bridge sw1 has no ports attached..
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br sw1
//filter by port
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show brport eth1
02:00:00:12:01:02 vlan 0 master br0 permanent
00:17:42:8a:b4:05 vlan 0 master br0 permanent
00:17:42:8a:b4:07 self permanent
33:33:00:00:00:01 self permanent
// filter by port + bridge
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br br0 brport
sw1-p1
da:ac:46:27:d9:53 vlan 0 master br0 permanent
33:33:00:00:00:01 self permanent
// for shits and giggles (as they say in New Brunswick), lets
// change the mac that br0 uses
// Note: a magical fdb entry with no brport is added ...
root@moja-1:/configs/may30-iprt/bridge# ip link set dev br0 address
02:00:00:12:01:04
// lets see if we can see the unicorn ..
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show
33:33:00:00:00:01 dev bond0 self permanent
33:33:00:00:00:01 dev dummy0 self permanent
33:33:00:00:00:01 dev ifb0 self permanent
33:33:00:00:00:01 dev ifb1 self permanent
33:33:00:00:00:01 dev eth0 self permanent
01:00:5e:00:00:01 dev eth0 self permanent
33:33:ff:22:01:01 dev eth0 self permanent
02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:07 dev eth1 self permanent
33:33:00:00:00:01 dev eth1 self permanent
33:33:00:00:00:01 dev gretap0 self permanent
02:00:00:12:01:04 dev br0 vlan 0 master br0 permanent <=== there it is
da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent
33:33:00:00:00:01 dev sw1-p1 self permanent
//can we see it if we filter by bridge?
root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br br0
02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent
00:17:42:8a:b4:07 dev eth1 self permanent
33:33:00:00:00:01 dev eth1 self permanent
02:00:00:12:01:04 dev br0 vlan 0 master br0 permanent <=== there it is
da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent
33:33:00:00:00:01 dev sw1-p1 self permanent
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumping a bridge fdb dumps every fdb entry
held. With this change we are going to filter
on selected bridge port.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a bonding master reclaims the netpoll info struct, slaves could
still hold a pointer to the reclaimed data. This patch fixes it: as
soon as netpoll_async_cleanup is called for a slave (eg. when
un-enslaved), we make sure that this slave doesn't point to the data.
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
load_pointer() is already a static inline function.
Let's move it into filter.h so BPF JIT implementations can reuse this
function.
Since we're exporting this function, let's also rename it to
bpf_load_pointer() for clarity.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sw_hash flag to skbuff to indicate that skb->hash was computed
from flow_dissector. This flag is checked in skb_get_hash to avoid
repeatedly trying to compute the hash (ie. in the case that no L4 hash
can be computed).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the receive side to support RFC 6438 which is to
use the flow label as an ECMP hash. If an IPv6 flow label is set
in a packet we can use this as input for computing an L4-hash. There
should be no need to parse any transport headers in this case.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call standard function to get a packet hash instead of taking this from
skb->sk->sk_hash or only using skb->protocol.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the hash computation located in __skb_get_hash to be a separate
function which takes flow_keys as input. This will allow flow hash
computation in other contexts where we only have addresses and ports.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp
classes are changed to orthogonal bitfields representing version, transport
and vlan values to simplify matching.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace two switch statements enumerating all valid ptp classes with an if
statement matching for not PTP_CLASS_NONE.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The if_lock()/if_unlock() in next_to_run() adds a significant
overhead, because its called for every packet in busy loop of
pktgen_thread_worker(). (Thomas Graf originally pointed me
at this lock problem).
Removing these two "LOCK" operations should in theory save us approx
16ns (8ns x 2), as illustrated below we do save 16ns when removing
the locks and introducing RCU protection.
Performance data with CLONE_SKB==100000, TX-size=512, rx-usecs=30:
(single CPU performance, ixgbe 10Gbit/s, E5-2630)
* Prev : 5684009 pps --> 175.93ns (1/5684009*10^9)
* RCU-fix: 6272204 pps --> 159.43ns (1/6272204*10^9)
* Diff : +588195 pps --> -16.50ns
To understand this RCU patch, I describe the pktgen thread model
below.
In pktgen there is several kernel threads, but there is only one CPU
running each kernel thread. Communication with the kernel threads are
done through some thread control flags. This allow the thread to
change data structures at a know synchronization point, see main
thread func pktgen_thread_worker().
Userspace changes are communicated through proc-file writes. There
are three types of changes, general control changes "pgctrl"
(func:pgctrl_write), thread changes "kpktgend_X"
(func:pktgen_thread_write), and interface config changes "etcX@N"
(func:pktgen_if_write).
Userspace "pgctrl" and "thread" changes are synchronized via the mutex
pktgen_thread_lock, thus only a single userspace instance can run.
The mutex is taken while the packet generator is running, by pgctrl
"start". Thus e.g. "add_device" cannot be invoked when pktgen is
running/started.
All "pgctrl" and all "thread" changes, except thread "add_device",
communicate via the thread control flags. The main problem is the
exception "add_device", that modifies threads "if_list" directly.
Fortunately "add_device" cannot be invoked while pktgen is running.
But there exists a race between "rem_device_all" and "add_device"
(which normally don't occur, because "rem_device_all" waits 125ms
before returning). Background'ing "rem_device_all" and running
"add_device" immediately allow the race to occur.
The race affects the threads (list of devices) "if_list". The if_lock
is used for protecting this "if_list". Other readers are given
lock-free access to the list under RCU read sections.
Note, interface config changes (via proc) can occur while pktgen is
running, which worries me a bit. I'm assuming proc_remove() takes
appropriate locks, to assure no writers exists after proc_remove()
finish.
I've been running a script exercising the race condition (leading me
to fix the proc_remove order), without any issues. The script also
exercises concurrent proc writes, while the interface config is
getting removed.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling set_current_state() inside the busy-loop in
pktgen_thread_worker(). In case of pkt_dev->delay, then it is still
used/enabled in pktgen_xmit() via the spin() call.
The set_current_state(TASK_INTERRUPTIBLE) uses a xchg, which implicit
is LOCK prefixed. I've measured the asm LOCK operation to take approx
8ns on this E5-2630 CPU. Performance increase corrolate with this
measurement.
Performance data with CLONE_SKB==100000, rx-usecs=30:
(single CPU performance, ixgbe 10Gbit/s, E5-2630)
* Prev: 5454050 pps --> 183.35ns (1/5454050*10^9)
* Now: 5684009 pps --> 175.93ns (1/5684009*10^9)
* Diff: +229959 pps --> -7.42ns
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, it is assumed that ops->setup is filled up. But there might be
case that ops might make sense even without ->setup. In that case,
forbid to newlink and dellink.
This allows to register simple rtnl link ops containing only ->kind.
That allows consistent way of passing device kind (either device-kind or
slave-kind) to userspace.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 371121057607e3127e19b3fa094330181b5b031e("net:
QDISC_STATE_RUNNING dont need atomic bit ops") the
__QDISC_STATE_RUNNING is renamed to __QDISC___STATE_RUNNING,
but the old names existing in comment are not replaced with
the new name completely.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Jones reported that a crash is occurring in
csum_partial
tcp_gso_segment
inet_gso_segment
? update_dl_migration
skb_mac_gso_segment
__skb_gso_segment
dev_hard_start_xmit
sch_direct_xmit
__dev_queue_xmit
? dev_hard_start_xmit
dev_queue_xmit
ip_finish_output
? ip_output
ip_output
ip_forward_finish
ip_forward
ip_rcv_finish
ip_rcv
__netif_receive_skb_core
? __netif_receive_skb_core
? trace_hardirqs_on
__netif_receive_skb
netif_receive_skb_internal
napi_gro_complete
? napi_gro_complete
dev_gro_receive
? dev_gro_receive
napi_gro_receive
It looks like a likely culprit is that SKB_GSO_CB()->csum_start is
not set correctly when doing non-scatter gather. We are using
offset as opposed to doffset.
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 7e2b10c1e5 ("net: Support for multiple checksums with gso")
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IP route cache had been removed in linux-3.6, we broke assumption
that dst entries were all freed after rcu grace period. DST_NOCACHE
dst were supposed to be freed from dst_release(). But it appears
we want to keep such dst around, either in UDP sockets or tunnels.
In sk_dst_get() we need to make sure dst refcount is not 0
before incrementing it, or else we might end up freeing a dst
twice.
DST_NOCACHE set on a dst does not mean this dst can not be attached
to a socket or a tunnel.
Then, before actual freeing, we need to observe a rcu grace period
to make sure all other cpus can catch the fact the dst is no longer
usable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dormando <dormando@rydia.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kcalloc/kmalloc_array to make it clear we're allocating arrays. No
integer overflow can actually happen here, since len/flen is guaranteed
to be less than BPF_MAXINSNS (4096). However, this changed makes sure
we're not going to get one if BPF_MAXINSNS were ever increased.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the order of the parameters to sk_unattached_filter_create() in
the kerneldoc to reflect the order they appear in the actual function.
This fix is only cosmetic, in the generated doc they still appear in the
correct order without the fix.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems overkill to use vmalloc() for typical listeners with less than
2048 hash buckets. Try kmalloc() and fallback to vmalloc() to reduce TLB
pressure.
Use kvfree() helper as it is now available.
Use ilog2() instead of a loop.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_flow_dissect() dissects only transport header type in ip_proto. It dose not
give any information about IPv4 or IPv6.
This patch adds new member, n_proto, to struct flow_keys. Which records the
IP layer type. i.e IPv4 or IPv6.
This can be used in netdev->ndo_rx_flow_steer driver function to dissect flow.
Adding new member to flow_keys increases the struct size by around 4 bytes.
This causes BUILD_BUG_ON(sizeof(qcb->data) < sz); to fail in
qdisc_cb_private_validate()
So increase data size by 4
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original checks (via sk_chk_filter) for instruction count uses ">",
not ">=", so changing this in sk_convert_filter has the potential to break
existing seccomp filters that used exactly BPF_MAXINSNS many instructions.
Fixes: bd4cf0ed33 ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org # v3.15+
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return the actual error code if call kset_create_and_add() failed
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __dev_open(), it already calls dev_set_rx_mode().
and dev_set_rx_mode() has no effect for a net device which does not have
IFF_UP flag set.
So the call of dev_set_rx_mode() is duplicate in __dev_change_flags().
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead517
("net: Save software checksum complete") is not correct.
This patch:
1) Restores code in __skb_checksum_complete_header except for setting
CHECKSUM_UNNECESSARY. This function may be calculating checksum on
something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
checksum 0..skb->len is calculated without adding in pseudo header.
This value is saved in skb->csum and then the pseudo header is added
to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
set skb->csum_valid to whether checksum of zero was computed. This
allows skb_csum_unnecessary to return true without changing to
CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
When running RHEL6 userspace on a current upstream kernel, "ip link"
fails to show VF information.
The reason is a kernel<->userspace API change introduced by commit
88c5b5ce5c ("rtnetlink: Call nlmsg_parse() with correct header length"),
after which the kernel does not see iproute2's IFLA_EXT_MASK attribute
in the netlink request.
iproute2 adjusted for the API change in its commit 63338dca4513
("libnetlink: Use ifinfomsg instead of rtgenmsg in rtnl_wilddump_req_filter").
The problem has been noticed before:
http://marc.info/?l=linux-netdev&m=136692296022182&w=2
(Subject: Re: getting VF link info seems to be broken in 3.9-rc8)
We can do better than tell those with old userspace to upgrade. We can
recognize the old iproute2 in the kernel by checking the netlink message
length. Even when including the IFLA_EXT_MASK attribute, its netlink
message is shorter than struct ifinfomsg.
With this patch "ip link" shows VF information in both old and new
iproute2 versions.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1d8faf48c7 (net/core: Add VF link state control) added VF link state
control to the netlink VF nested structure, but failed to add a proper entry
for the new structure into the VF policy table. Add the missing entry so
the table and the actual data copied into the netlink nested struct are in
sync.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In skb_checksum complete, if we need to compute the checksum for the
packet (via skb_checksum) save the result as CHECKSUM_COMPLETE.
Subsequent checksum verification can use this.
Also, added csum_complete_sw flag to distinguish between software and
hardware generated checksum complete, we should always be able to trust
the software computation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several instances where a pskb_copy or __pskb_copy is
immediately followed by an skb_clone.
Add a couple of new functions to allow the copy skb to be allocated
from the fclone cache and thus speed up subsequent skb_clone calls.
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix compiler warning on 32-bit architectures:
net/core/filter.c: In function '__sk_run_filter':
net/core/filter.c:540:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
net/core/filter.c:550:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
net/core/filter.c:560:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a kernel BUG_ON in skb_segment. It is hit when
testing two VMs on openvswitch with one VM acting as VXLAN gateway.
During VXLAN packet GSO, skb_segment is called with skb->data
pointing to inner TCP payload. skb_segment calls skb_network_protocol
to retrieve the inner protocol. skb_network_protocol actually expects
skb->data to point to MAC and it calls pskb_may_pull with ETH_HLEN.
This ends up pulling in ETH_HLEN data from header tail. As a result,
pskb_trim logic is skipped and BUG_ON is hit later.
Move skb_push in front of skb_network_protocol so that skb->data
lines up properly.
kernel BUG at net/core/skbuff.c:2999!
Call Trace:
[<ffffffff816ac412>] tcp_gso_segment+0x122/0x410
[<ffffffff816bc74c>] inet_gso_segment+0x13c/0x390
[<ffffffff8164b39b>] skb_mac_gso_segment+0x9b/0x170
[<ffffffff816b3658>] skb_udp_tunnel_segment+0xd8/0x390
[<ffffffff816b3c00>] udp4_ufo_fragment+0x120/0x140
[<ffffffff816bc74c>] inet_gso_segment+0x13c/0x390
[<ffffffff8109d742>] ? default_wake_function+0x12/0x20
[<ffffffff8164b39b>] skb_mac_gso_segment+0x9b/0x170
[<ffffffff8164b4d0>] __skb_gso_segment+0x60/0xc0
[<ffffffff8164b6b3>] dev_hard_start_xmit+0x183/0x550
[<ffffffff8166c91e>] sch_direct_xmit+0xfe/0x1d0
[<ffffffff8164bc94>] __dev_queue_xmit+0x214/0x4f0
[<ffffffff8164bf90>] dev_queue_xmit+0x10/0x20
[<ffffffff81687edb>] ip_finish_output+0x66b/0x890
[<ffffffff81688a58>] ip_output+0x58/0x90
[<ffffffff816c628f>] ? fib_table_lookup+0x29f/0x350
[<ffffffff816881c9>] ip_local_out_sk+0x39/0x50
[<ffffffff816cbfad>] iptunnel_xmit+0x10d/0x130
[<ffffffffa0212200>] vxlan_xmit_skb+0x1d0/0x330 [vxlan]
[<ffffffffa02a3919>] vxlan_tnl_send+0x129/0x1a0 [openvswitch]
[<ffffffffa02a2cd6>] ovs_vport_send+0x26/0xa0 [openvswitch]
[<ffffffffa029931e>] do_output+0x2e/0x50 [openvswitch]
Signed-off-by: Wei-Chun Chao <weichunc@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro 'A' used in internal BPF interpreter:
#define A regs[insn->a_reg]
was easily confused with the name of classic BPF register 'A', since
'A' would mean two different things depending on context.
This patch is trying to clean up the naming and clarify its usage in the
following way:
- A and X are names of two classic BPF registers
- BPF_REG_A denotes internal BPF register R0 used to map classic register A
in internal BPF programs generated from classic
- BPF_REG_X denotes internal BPF register R7 used to map classic register X
in internal BPF programs generated from classic
- internal BPF instruction format:
struct sock_filter_int {
__u8 code; /* opcode */
__u8 dst_reg:4; /* dest register */
__u8 src_reg:4; /* source register */
__s16 off; /* signed offset */
__s32 imm; /* signed immediate constant */
};
- BPF_X/BPF_K is 1 bit used to encode source operand of instruction
In classic:
BPF_X - means use register X as source operand
BPF_K - means use 32-bit immediate as source operand
In internal:
BPF_X - means use 'src_reg' register as source operand
BPF_K - means use 32-bit immediate as source operand
Suggested-by: Chema Gonzalez <chema@google.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Chema Gonzalez <chema@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup updates from Tejun Heo:
"A lot of activities on cgroup side. Heavy restructuring including
locking simplification took place to improve the code base and enable
implementation of the unified hierarchy, which currently exists behind
a __DEVEL__ mount option. The core support is mostly complete but
individual controllers need further work. To explain the design and
rationales of the the unified hierarchy
Documentation/cgroups/unified-hierarchy.txt
is added.
Another notable change is css (cgroup_subsys_state - what each
controller uses to identify and interact with a cgroup) iteration
update. This is part of continuing updates on css object lifetime and
visibility. cgroup started with reference count draining on removal
way back and is now reaching a point where csses behave and are
iterated like normal refcnted objects albeit with some complexities to
allow distinguishing the state where they're being deleted. The css
iteration update isn't taken advantage of yet but is planned to be
used to simplify memcg significantly"
* 'for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (77 commits)
cgroup: disallow disabled controllers on the default hierarchy
cgroup: don't destroy the default root
cgroup: disallow debug controller on the default hierarchy
cgroup: clean up MAINTAINERS entries
cgroup: implement css_tryget()
device_cgroup: use css_has_online_children() instead of has_children()
cgroup: convert cgroup_has_live_children() into css_has_online_children()
cgroup: use CSS_ONLINE instead of CGRP_DEAD
cgroup: iterate cgroup_subsys_states directly
cgroup: introduce CSS_RELEASED and reduce css iteration fallback window
cgroup: move cgroup->serial_nr into cgroup_subsys_state
cgroup: link all cgroup_subsys_states in their sibling lists
cgroup: move cgroup->sibling and ->children into cgroup_subsys_state
cgroup: remove cgroup->parent
device_cgroup: remove direct access to cgroup->children
memcg: update memcg_has_children() to use css_next_child()
memcg: remove tasks/children test from mem_cgroup_force_empty()
cgroup: remove css_parent()
cgroup: skip refcnting on normal root csses and cgrp_dfl_root self css
cgroup: use cgroup->self.refcnt for cgroup refcnting
...
unregister_netdevice_many() API is error prone and we had too
many bugs because of dangling LIST_HEAD on stacks.
See commit f87e6f4793 ("net: dont leave active on stack LIST_HEAD")
In fact, instead of making sure no caller leaves an active list_head,
just force a list_del() in the callee. No one seems to need to access
the list after unregister_netdevice_many()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
Conflicts:
drivers/net/xen-netback/netback.c
net/core/filter.c
A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.
A xen-netback bug fix overlapped the addition of multi-queue
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF classic->internal converter broke SKF_AD_PKTTYPE extension, since
pkt_type_offset() was failing to find skb->pkt_type field which is defined as:
__u8 pkt_type:3,
fclone:2,
ipvs_property:1,
peeked:1,
nf_trace:1;
Fix it by searching for 3 most significant bits and shift them by 5 at run-time
Fixes: bd4cf0ed33 ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an MPLS packet requires segmentation then use mpls_features
to determine if the software implementation should be used.
As no driver advertises MPLS GSO segmentation this will always be
the case.
I had not noticed that this was necessary before as software MPLS GSO
segmentation was already being used in my test environment. I believe that
the reason for that is the skbs in question always had fragments and the
driver I used does not advertise NETIF_F_FRAGLIST (which seems to be the
case for most drivers). Thus software segmentation was activated by
skb_gso_ok().
This introduces the overhead of an extra call to skb_network_protocol()
in the case where where CONFIG_NET_MPLS_GSO is set and
skb->ip_summed == CHECKSUM_NONE.
Thanks to Jesse Gross for prompting me to investigate this.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is available since v3.15-rc5.
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a GSO packet segment we may need to set more than
one checksum in the packet (for instance a TCP checksum and
UDP checksum for VXLAN encapsulation). To be efficient, we want
to do checksum calculation for any part of the packet at most once.
This patch adds csum_start offset to skb_gso_cb. This tracks the
starting offset for skb->csum which is initially set in skb_segment.
When a protocol needs to compute a transport checksum it calls
gso_make_checksum which computes the checksum value from the start
of transport header to csum_start and then adds in skb->csum to get
the full checksum. skb->csum and csum_start are then updated to reflect
the checksum of the resultant packet starting from the transport header.
This patch also adds a flag to skbuff, encap_hdr_csum, which is set
in *gso_segment fucntions to indicate that a tunnel protocol needs
checksum calculation
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we jump to free_pcpu on failure in alloc_netdev_mqs()
rx and tx queues are not yet allocated, so no need to free them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that ->newlink() fails before registering
the device, in this case we should just free it, it's
safe to call free_netdev().
Fixes: commit 0e0eee2465 (net: correct error path in rtnl_newlink())
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Pull request: Fixes for new ethtool RSS commands
This addresses several problems I previously identified with the new
ETHTOOL_{G,S}RSSH commands:
1. Missing validation of reserved parameters
2. Vague documentation
3. Use of unnamed magic number
4. No consolidation with existing driver operations
I don't currently have access to suitable network hardware, but have
tested these changes with a dummy driver that can support various
combinations of operations and sizes, together with (a) Debian's ethtool
3.13 (b) ethtool 3.14 with the submitted patch to use ETHTOOL_{G,S}RSSH
and minor adjustment for fixes 1 and 3.
v2: Update RSS operations in vmxnet3 too
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
