ipwireless: Increase PPP outgoing queue size
Increase default size of PPP outgoing queue. Currently set to 1, which
means that a packet quickly following another pushed by PPP must wait
until hardware actually sends the previous and PPP has to be waken up
by ppp_wakeup(). This slows down upstream.
Now PPP can push more packets at once which get buffered inside driver
and pushed immediatelly to hardware when previous packet is out.
Experiments show that size = 10 is quite good for all connection types
(GPRS/EDGE/UMTS) and gains 4 KB/sec of upload for UMTS for batch uploads.
Need for higher queue size than 10 occures in only < 0.1 % of cases.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipwireless: Explicitly request io and mem regions
Documentation/pcmcia/driver-changes.txt says, that driver should call request_region
for used memory/io regions since PCMCIA does not do this (since 2.6.8).
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipwireless: Do not return value from sending funcs
Do not return value from do_send_fragment and do_send_packet, it's not used.
The packet size checks are not useful too:
* zero length packet will never be sent, caller always passes packet_header
size which is either 1 or 3
* MTU check is done in caller, no need to repeat
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipwireless: Misc cleanups
- remove likely() and some extra () in ifs
- use unsigned in for loops
- remove useless typecasts
- remove obvious comments
- add () around ?:
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: state userland requirements in Kconfig help
firewire: avoid memleak after phy config transmit failure
firewire: fw-ohci: TSB43AB22/A dualbuffer workaround
firewire: queue the right number of data
firewire: warn on unfinished transactions during card removal
firewire: small fw_fill_request cleanup
firewire: fully initialize fw_transaction before marking it pending
firewire: fix race of bus reset with request transmission
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (59 commits)
[SCSI] replace __FUNCTION__ with __func__
[SCSI] extend the last_sector_bug flag to cover more sectors
[SCSI] qla2xxx: Update version number to 8.02.01-k6.
[SCSI] qla2xxx: Additional NPIV corrections.
[SCSI] qla2xxx: suppress uninitialized-var warning
[SCSI] qla2xxx: use memory_read_from_buffer()
[SCSI] qla2xxx: Issue proper ISP callbacks during stop-firmware.
[SCSI] ch: fix ch_remove oops
[SCSI] 3w-9xxx: add MSI support and misc fixes
[SCSI] scsi_lib: use blk_rq_tagged in scsi_request_fn
[SCSI] ibmvfc: Update driver version to 1.0.1
[SCSI] ibmvfc: Add ADISC support
[SCSI] ibmvfc: Miscellaneous fixes
[SCSI] ibmvfc: Fix hang on module removal
[SCSI] ibmvfc: Target refcounting fixes
[SCSI] ibmvfc: Reduce unnecessary log noise
[SCSI] sym53c8xx: free luntbl in sym_hcb_free
[SCSI] scsi_scan.c: Release mutex in error handling code
[SCSI] scsi_eh_prep_cmnd should save scmd->underflow
[SCSI] sd: Support for SCSI disk (SBC) Data Integrity Field
...
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: some mmc/sd cleanups
include/video/atmel_lcdc.h must #include <linux/workqueue.h>
avr32: allow system timer to share interrupt to make OProfile work
drivers/misc/atmel-ssc.c: Removed duplicated include
avr32: Add platform data for AC97C platform device
avr32: clean up mci platform code
fix avr32 build errors
* 'kvm-updates-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: ppc: fix invalidation of large guest pages
KVM: s390: Fix possible host kernel bug on lctl(g) handling
KVM: s390: Fix instruction naming for lctlg
KVM: s390: Fix program check on interrupt delivery handling
KVM: s390: Change guestaddr type in gaccess
KVM: s390: Fix guest kconfig
KVM: s390: Advertise KVM_CAP_USER_MEMORY
KVM: ia64: Fix irq disabling leak in error handling code
KVM: VMX: Fix undefined beaviour of EPT after reload kvm-intel.ko
KVM: VMX: Fix bypass_guest_pf enabling when disable EPT in module parameter
KVM: task switch: translate guest segment limit to virt-extension byte granular field
KVM: Avoid instruction emulation when event delivery is pending
KVM: task switch: use seg regs provided by subarch instead of reading from GDT
KVM: task switch: segment base is linear address
KVM: SVM: allow enabling/disabling NPT by reloading only the architecture module
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (25 commits)
setlocalversion: do not describe if there is nothing to describe
kconfig: fix typos: "Suport" -> "Support"
kconfig: make defconfig is no longer chatty
kconfig: make oldconfig is now less chatty
kconfig: speed up all*config + randconfig
kconfig: set all new symbols automatically
kconfig: add diffconfig utility
kbuild: remove Module.markers during mrproper
kbuild: sparse needs CF not CHECKFLAGS
kernel-doc: handle/strip __init
vmlinux.lds: move __attribute__((__cold__)) functions back into final .text section
init: fix URL of "The GNU Accounting Utilities"
kbuild: add arch/$ARCH/include to search path
kbuild: asm symlink support for arch/$ARCH/include
kbuild: support arch/$ARCH/include for tags, cscope
kbuild: prepare headers_* for arch/$ARCH/include
kbuild: install all headers when arch is changed
kbuild: make clean removes *.o.* as well
kbuild: optimize headers_* targets
kbuild: only one call for include/ in make headers_*
...
On powerpc (allyesconfig build) we get this error:
drivers/isdn/hardware/mISDN/hfcpci.c:1991: error: implicit declaration of function 'virt_to_bus'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
you can pull this git://git./linux/kernel/git/kkeil/ISDN-2.6 master
rename release_tei() to TEIrelease() because release_tei() was
already exported bei the old HiSax driver.
Signed-off-by: Karsten Keil <kkeil@suse.de>
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The last_sector_bug flag was added to work around a bug in certain usb
cardreaders, where they would crash if a multiple sector read included the
last sector. The original implementation avoids this by e.g. splitting an 8
sector read which includes the last sector into a 7 sector read, and a single
sector read for the last sector. The flag is enabled for all USB devices.
This revealed a second bug in other usb cardreaders, which crash when they
get a multiple sector read which stops 1 sector short of the last sector.
Affected hardware includes the Kingston "MobileLite" external USB cardreader
and the internal USB cardreader on the Asus EeePC.
Extend the last_sector_bug workaround to ensure that any access which touches
the last 8 hardware sectors of the device is a single sector long. Requests
are shrunk as necessary to meet this constraint.
This gives us a safety margin against potential unknown or future bugs
affecting multi-sector access to the end of the device. The two known bugs
only affect the last 2 sectors. However, they suggest that these devices
are prone to fencepost errors and that multi-sector access to the end of the
device is not well tested. Popular OS's use multi-sector accesses, but they
rarely read the last few sectors. Linux (with udev & vol_id) automatically
reads sectors from the end of the device on insertion. It is assumed that
single sector accesses are more thoroughly tested during development.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Minor cleanups for the MMC/SD support on avr32:
- Make at32_add_device_mci() properly initialize "missing"
platform data ... so boards like STK1002 won't try GPIO 0.
- Switch over to gpio_is_valid() instead of testing for only
one designated value.
- Provide STK1002 platform data for the unlikely case that
switches are set so first Ethernet controller isn't in use.
(That's the only way to get card detect and writeprotect
switch sensing on the STK1000.)
And get rid of one "unused variable" warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cornelia Huck noticed that a modular virtio without kvm guest support
leads to a build error in the s390 virtio transport:
CONFIG_VIRTIO=m leads to
ERROR: "vmem_add_mapping" [drivers/s390/kvm/kvm_virtio.ko] undefined!
ERROR: "max_pfn" [drivers/s390/kvm/kvm_virtio.ko] undefined!
ERROR: "vmem_remove_mapping" [drivers/s390/kvm/kvm_virtio.ko] undefined!
The virtio transport only works with kvm guest support and only as a
builtin. Lets change the build process of drivers/s390/kvm/kvm_virtio.c
to depend on kvm guest support, which is also a bool.
CONFIG_S390_GUEST already selects CONFIG_VIRTIO, that should prevent
CONFIG_S390_GUEST=y CONFIG_VIRTIO=n situations.
CC: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4: Update/add Mellanox Technologies copyright lines to mlx4 driver files
mlx4_core: Add VLAN tag field to WQE control segment struct
RDMA/nes: CM connection setup/teardown rework
IPoIB: Correct help text for INFINIBAND_IPOIB_DEBUG
IPoIB/cm: Connected mode is no longer EXPERIMENTAL
RDMA/ucm: BKL is not needed for ib_ucm_open()
RDMA/ucma: BKL is not needed for ucma_open()
The fix NULLed a pointer without freeing it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Juha Motorsportcom <juha_motorsportcom@luukku.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6: (57 commits)
[MTD] [NAND] subpage read feature as a way to increase performance.
CPUFREQ: S3C24XX NAND driver frequency scaling support.
[MTD][NAND] au1550nd: remove unused variable
[MTD] jedec_probe: Fix SST 16-bit chip detection
[MTD][MTDPART] Fix a division by zero bug
[MTD][MTDPART] Cleanup and document the erase region handling
[MTD][MTDPART] Handle most checkpatch findings
[MTD][MTDPART] Seperate main loop from per-partition code in add_mtd_partition
[MTD] physmap: resume already suspended chips on failure to suspend
[MTD] physmap: Fix suspend/resume/shutdown bugs.
[MTD] [NOR] Fix -ETIMEO errors in CFI driver
[MTD] [NAND] fsl_elbc_nand: fix section mismatch with CONFIG_MTD_OF_PARTS=y
[JFFS2] Use .unlocked_ioctl
[MTD] Fix const assignment in the MTD command line partitioning driver
[MTD] [NOR] gen_probe: No debug message when debugging is disabled
[MTD] [NAND] remove __PPC__ hardcoded address from DiskOnChip drivers
[MTD] [MAPS] Remove the bast-flash driver.
[MTD] [NAND] fsl_elbc_nand: ecclayout cleanups
[MTD] [NAND] fsl_elbc_nand: implement support for flash-based BBT
[MTD] [NAND] fsl_elbc_nand: fix OOB workability for large page NAND chips
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
atmel-mci: debugfs support
mmc: Add per-card debugfs support
mmc: Export internal host state through debugfs
imxmmc: fix crash when no platform data is provided
imxmmc: fix platform resources
imxmmc: remove DEBUG definition
mmc_spi: put signals to low power off fix
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (39 commits)
[PATCH] fix RLIM_NOFILE handling
[PATCH] get rid of corner case in dup3() entirely
[PATCH] remove remaining namei_{32,64}.h crap
[PATCH] get rid of indirect users of namei.h
[PATCH] get rid of __user_path_lookup_open
[PATCH] f_count may wrap around
[PATCH] dup3 fix
[PATCH] don't pass nameidata to __ncp_lookup_validate()
[PATCH] don't pass nameidata to gfs2_lookupi()
[PATCH] new (local) helper: user_path_parent()
[PATCH] sanitize __user_walk_fd() et.al.
[PATCH] preparation to __user_walk_fd cleanup
[PATCH] kill nameidata passing to permission(), rename to inode_permission()
[PATCH] take noexec checks to very few callers that care
Re: [PATCH 3/6] vfs: open_exec cleanup
[patch 4/4] vfs: immutable inode checking cleanup
[patch 3/4] fat: dont call notify_change
[patch 2/4] vfs: utimes cleanup
[patch 1/4] vfs: utimes: move owner check into inode_change_ok()
[PATCH] vfs: use kstrdup() and check failing allocation
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix ip_rt_frag_needed rt_is_expired
netfilter: nf_conntrack_extend: avoid unnecessary "ct->ext" dereferences
netfilter: fix double-free and use-after free
netfilter: arptables in netns for real
netfilter: ip{,6}tables_security: fix future section mismatch
selinux: use nf_register_hooks()
netfilter: ebtables: use nf_register_hooks()
Revert "pkt_sched: sch_sfq: dump a real number of flows"
qeth: use dev->ml_priv instead of dev->priv
syncookies: Make sure ECN is disabled
net: drop unused BUG_TRAP()
net: convert BUG_TRAP to generic WARN_ON
drivers/net: convert BUG_TRAP to generic WARN_ON
Fix firmware/memmap printk format warnings:
drivers/firmware/memmap.c:156: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/firmware/memmap.c:161: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Bernhard Walle <bwalle@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make it atomic_long_t; while we are at it, get rid of useless checks in affs,
hfs and hpfs - ->open() always has it equal to 1, ->release() - to 0.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Enable support for digital audio processing capability.
This module may be used for special applications that require
cross connecting of bchannels, conferencing, dtmf decoding
echo cancelation, tone generation, and Blowfish encryption and
decryption.
It may use hardware features if available.
Signed-off-by: Karsten Keil <kkeil@suse.de>
mISDN is a new modular ISDN driver, in the long term it should replace
the old I4L driver architecture for passiv ISDN cards.
Signed-off-by: Karsten Keil <kkeil@suse.de>
For each card successfully added to the bus, create a subdirectory under
the host's debugfs root with information about the card.
At the moment, only a single file is added to the card directory for
all cards: "state". It reflects the "state" field in struct mmc_card,
indicating whether the card is present, readonly, etc.
For MMC and SD cards (not SDIO), another file is added: "status".
Reading this file will ask the card about its current status and
return it. This can be useful if the card just refuses to respond to
any commands, which might indicate that the card state is not what the
MMC core thinks it is (due to a missing stop command, for example.)
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
When CONFIG_DEBUG_FS is set, create a few files under /sys/kernel/debug
containing information about an mmc host's internal state. Currently,
just a single file is created, "ios", which contains information about
the current operating parameters for the bus (clock speed, bus width,
etc.)
Host drivers can add additional files and directories under the host's
root directory by passing the debugfs_root field in struct mmc_host as
the 'parent' parameter to debugfs_create_*.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Don't crash if no platform data is provided.
In this case assume that card is present.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fixup platform resources handling.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Removed DEBUG #define #undef, because module is automaticaly
compiled with -DDEBUG when CONFIG_MMC_DEBUG is defined.
Currently it just generates compiler warning about redefinition.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
